diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/nand-controller.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/nand-controller.yaml | 85 |
1 files changed, 2 insertions, 83 deletions
diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml index f70a32d2d9d4..83a4fe4cc29d 100644 --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -16,16 +16,6 @@ description: | children nodes of the NAND controller. This representation should be enforced even for simple controllers supporting only one chip. - The ECC strength and ECC step size properties define the user - desires in terms of correction capability of a controller. Together, - they request the ECC engine to correct {strength} bit errors per - {size} bytes. - - The interpretation of these parameters is implementation-defined, so - not all implementations must support all possible - combinations. However, implementations are encouraged to further - specify the value(s) they support. - properties: $nodename: pattern: "^nand-controller(@.*)?" @@ -51,79 +41,8 @@ properties: patternProperties: "^nand@[a-f0-9]$": - $ref: nand-chip.yaml# - - properties: - reg: - description: - Contains the chip-select IDs. - - nand-ecc-placement: - description: - Location of the ECC bytes. This location is unknown by default - but can be explicitly set to "oob", if all ECC bytes are - known to be stored in the OOB area, or "interleaved" if ECC - bytes will be interleaved with regular data in the main area. - $ref: /schemas/types.yaml#/definitions/string - enum: [ oob, interleaved ] - - nand-bus-width: - description: - Bus width to the NAND chip - $ref: /schemas/types.yaml#/definitions/uint32 - enum: [8, 16] - default: 8 - - nand-on-flash-bbt: - description: - With this property, the OS will search the device for a Bad - Block Table (BBT). If not found, it will create one, reserve - a few blocks at the end of the device to store it and update - it as the device ages. Otherwise, the out-of-band area of a - few pages of all the blocks will be scanned at boot time to - find Bad Block Markers (BBM). These markers will help to - build a volatile BBT in RAM. - $ref: /schemas/types.yaml#/definitions/flag - - nand-ecc-maximize: - description: - Whether or not the ECC strength should be maximized. The - maximum ECC strength is both controller and chip - dependent. The ECC engine has to select the ECC config - providing the best strength and taking the OOB area size - constraint into account. This is particularly useful when - only the in-band area is used by the upper layers, and you - want to make your NAND as reliable as possible. - $ref: /schemas/types.yaml#/definitions/flag - - nand-is-boot-medium: - description: - Whether or not the NAND chip is a boot medium. Drivers might - use this information to select ECC algorithms supported by - the boot ROM or similar restrictions. - $ref: /schemas/types.yaml#/definitions/flag - - nand-rb: - description: - Contains the native Ready/Busy IDs. - $ref: /schemas/types.yaml#/definitions/uint32-array - - rb-gpios: - description: - Contains one or more GPIO descriptor (the numper of descriptor - depends on the number of R/B pins exposed by the flash) for the - Ready/Busy pins. Active state refers to the NAND ready state and - should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted. - - wp-gpios: - description: - Contains one GPIO descriptor for the Write Protect pin. - Active state refers to the NAND Write Protect state and should be - set to GPIOD_ACTIVE_LOW unless the signal is inverted. - maxItems: 1 - - required: - - reg + type: object + $ref: raw-nand-chip.yaml# required: - "#address-cells" |