diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/xilinx_axienet.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/xilinx_axienet.txt | 101 |
1 files changed, 0 insertions, 101 deletions
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt deleted file mode 100644 index 80e505a2fda1..000000000000 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ /dev/null @@ -1,101 +0,0 @@ -XILINX AXI ETHERNET Device Tree Bindings --------------------------------------------------------- - -Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core -provides connectivity to an external ethernet PHY supporting different -interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two -segments of memory for buffering TX and RX, as well as the capability of -offloading TX/RX checksum calculation off the processor. - -Management configuration is done through the AXI interface, while payload is -sent and received through means of an AXI DMA controller. This driver -includes the DMA driver code, so this driver is incompatible with AXI DMA -driver. - -For more details about mdio please refer phy.txt file in the same directory. - -Required properties: -- compatible : Must be one of "xlnx,axi-ethernet-1.00.a", - "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" -- reg : Address and length of the IO space, as well as the address - and length of the AXI DMA controller IO space, unless - axistream-connected is specified, in which case the reg - attribute of the node referenced by it is used. -- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA, - and optionally Ethernet core. If axistream-connected is - specified, the TX/RX DMA interrupts should be on that node - instead, and only the Ethernet core interrupt is optionally - specified here. -- phy-handle : Should point to the external phy device if exists. Pointing - this to the PCS/PMA PHY is deprecated and should be avoided. - See ethernet.txt file in the same directory. -- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware - -Optional properties: -- phy-mode : See ethernet.txt -- xlnx,phy-type : Deprecated, do not use, but still accepted in preference - to phy-mode. -- xlnx,txcsum : 0 or empty for disabling TX checksum offload, - 1 to enable partial TX checksum offload, - 2 to enable full TX checksum offload -- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload -- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to - support both 1000BaseX and SGMII modes. If set, the phy-mode - should be set to match the mode selected on core reset (i.e. - by the basex_or_sgmii core input line). -- clock-names: Tuple listing input clock names. Possible clocks: - s_axi_lite_clk: Clock for AXI register slave interface - axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces - ref_clk: Ethernet reference clock, used by signal delay - primitives and transceivers - mgt_clk: MGT reference clock (used by optional internal - PCS/PMA PHY) - - Note that if s_axi_lite_clk is not specified by name, the - first clock of any name is used for this. If that is also not - specified, the clock rate is auto-detected from the CPU clock - (but only on platforms where this is possible). New device - trees should specify all applicable clocks by name - the - fallbacks to an unnamed clock or to CPU clock are only for - backward compatibility. -- clocks: Phandles to input clocks matching clock-names. Refer to common - clock bindings. -- axistream-connected: Reference to another node which contains the resources - for the AXI DMA controller used by this device. - If this is specified, the DMA-related resources from that - device (DMA registers and DMA TX/RX interrupts) rather - than this one will be used. - - mdio : Child node for MDIO bus. Must be defined if PHY access is - required through the core's MDIO interface (i.e. always, - unless the PHY is accessed through a different bus). - Non-standard MDIO bus frequency is supported via - "clock-frequency", see mdio.yaml. - - - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X - modes, where "pcs-handle" should be used to point - to the PCS/PMA PHY, and "phy-handle" should point to an - external PHY if exists. - -Example: - axi_ethernet_eth: ethernet@40c00000 { - compatible = "xlnx,axi-ethernet-1.00.a"; - device_type = "network"; - interrupt-parent = <µblaze_0_axi_intc>; - interrupts = <2 0 1>; - clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; - clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; - phy-mode = "mii"; - reg = <0x40c00000 0x40000 0x50c00000 0x40000>; - xlnx,rxcsum = <0x2>; - xlnx,rxmem = <0x800>; - xlnx,txcsum = <0x2>; - phy-handle = <&phy0>; - axi_ethernetlite_0_mdio: mdio { - #address-cells = <1>; - #size-cells = <0>; - phy0: phy@0 { - device_type = "ethernet-phy"; - reg = <1>; - }; - }; - }; |