diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml | 183 |
1 files changed, 183 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml new file mode 100644 index 000000000000..1d33d80af11c --- /dev/null +++ b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml @@ -0,0 +1,183 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/xlnx,axi-ethernet.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AXI 1G/2.5G Ethernet Subsystem + +description: | + Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core + provides connectivity to an external ethernet PHY supporting different + interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two + segments of memory for buffering TX and RX, as well as the capability of + offloading TX/RX checksum calculation off the processor. + + Management configuration is done through the AXI interface, while payload is + sent and received through means of an AXI DMA controller. This driver + includes the DMA driver code, so this driver is incompatible with AXI DMA + driver. + +maintainers: + - Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> + +properties: + compatible: + enum: + - xlnx,axi-ethernet-1.00.a + - xlnx,axi-ethernet-1.01.a + - xlnx,axi-ethernet-2.01.a + + reg: + description: + Address and length of the IO space, as well as the address + and length of the AXI DMA controller IO space, unless + axistream-connected is specified, in which case the reg + attribute of the node referenced by it is used. + maxItems: 2 + + interrupts: + items: + - description: Ethernet core interrupt + - description: Tx DMA interrupt + - description: Rx DMA interrupt + description: + Ethernet core interrupt is optional. If axistream-connected property is + present DMA node should contains TX/RX DMA interrupts else DMA interrupt + resources are mentioned on ethernet node. + minItems: 1 + + phy-handle: true + + xlnx,rxmem: + description: + Set to allocated memory buffer for Rx/Tx in the hardware. + $ref: /schemas/types.yaml#/definitions/uint32 + + phy-mode: + enum: + - mii + - gmii + - rgmii + - sgmii + - 1000BaseX + + xlnx,phy-type: + description: + Do not use, but still accepted in preference to phy-mode. + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + + xlnx,txcsum: + description: + TX checksum offload. 0 or empty for disabling TX checksum offload, + 1 to enable partial TX checksum offload and 2 to enable full TX + checksum offload. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + xlnx,rxcsum: + description: + RX checksum offload. 0 or empty for disabling RX checksum offload, + 1 to enable partial RX checksum offload and 2 to enable full RX + checksum offload. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + xlnx,switch-x-sgmii: + type: boolean + description: + Indicate the Ethernet core is configured to support both 1000BaseX and + SGMII modes. If set, the phy-mode should be set to match the mode + selected on core reset (i.e. by the basex_or_sgmii core input line). + + clocks: + items: + - description: Clock for AXI register slave interface. + - description: AXI4-Stream clock for TXD RXD TXC and RXS interfaces. + - description: Ethernet reference clock, used by signal delay primitives + and transceivers. + - description: MGT reference clock (used by optional internal PCS/PMA PHY) + + clock-names: + items: + - const: s_axi_lite_clk + - const: axis_clk + - const: ref_clk + - const: mgt_clk + + axistream-connected: + $ref: /schemas/types.yaml#/definitions/phandle + description: Phandle of AXI DMA controller which contains the resources + used by this device. If this is specified, the DMA-related resources + from that device (DMA registers and DMA TX/RX interrupts) rather than + this one will be used. + + mdio: + type: object + + pcs-handle: + description: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X + modes, where "pcs-handle" should be used to point to the PCS/PMA PHY, + and "phy-handle" should point to an external PHY if exists. + maxItems: 1 + +required: + - compatible + - interrupts + - reg + - xlnx,rxmem + - phy-handle + +allOf: + - $ref: /schemas/net/ethernet-controller.yaml# + +additionalProperties: false + +examples: + - | + axi_ethernet_eth: ethernet@40c00000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + interrupts = <2 0 1>; + clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; + clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; + phy-mode = "mii"; + reg = <0x40c00000 0x40000>,<0x50c00000 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@1 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; + + - | + axi_ethernet_eth1: ethernet@40000000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + interrupts = <0>; + clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; + clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; + phy-mode = "mii"; + reg = <0x00 0x40000000 0x00 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy1>; + axistream-connected = <&dma>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy1: ethernet-phy@1 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; |