diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
4 files changed, 10 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index d6c6e41648d4..8ec2ca21adeb 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -34,7 +34,7 @@ Required properties: "brcm,bcm6328-switch" "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" -See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. Examples: diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 7ef9dbb08957..1d4d0f49c9d0 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -26,6 +26,10 @@ Optional properties: - interrupt-controller : Indicates the switch is itself an interrupt controller. This is used for the PHY interrupts. #interrupt-cells = <2> : Controller uses two cells, number and flag +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. - mdio : Container of PHY and devices on the switches MDIO bus. - mdio? : Container of PHYs and devices on the external MDIO diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index a1e3693cca16..6f55bdd52f8a 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -15,6 +15,10 @@ Optional properties: - phy-reset-active-high : If present then the reset sequence using the GPIO specified in the "phy-reset-gpios" property is reversed (H=reset state, L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - phy-supply : regulator that powers the Ethernet PHY. - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt index 16c3a9501f5d..acfafc8e143c 100644 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -27,6 +27,7 @@ Optional properties: of the device. On many systems this is wired high so the device goes out of reset at power-on, but if it is under program control, this optional GPIO can wake up in response to it. +- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies Examples: |