1 files changed, 0 insertions, 99 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt
deleted file mode 100644
index b0e36cf0d289..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt
+++ /dev/null
@@ -1,99 +0,0 @@
-Cirrus Logic Madera class audio codecs pinctrl driver
-
-The Cirrus Logic Madera codecs provide a number of GPIO functions for
-interfacing to external hardware and to provide logic outputs to other devices.
-Certain groups of GPIO pins also have an alternate function, normally as an
-audio interface.
-
-The set of available GPIOs, functions and alternate function groups differs
-between codecs so refer to the datasheet for the codec for further information
-on what is supported on that device.
-
-The properties for this driver exist within the parent MFD driver node.
-
-See also
-  the core bindings for the parent MFD driver:
-    Documentation/devicetree/bindings/mfd/madera.txt
-
-  the generic pinmix bindings:
-    Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
-Required properties of parent mfd node:
-  - pinctrl-names : must be "default"
-  - pinctrl-0 : a phandle to the node containing the subnodes containing default
-      configurations
-
-Required subnodes:
-  One subnode is required to contain the default settings. It contains an
-  arbitrary number of configuration subnodes, one for each group or pin
-  configuration you want to apply as a default.
-
-Required properties of configuration subnodes:
-  - groups : name of one pin group to configure. One of:
-	aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2,
-	dmic4, dmic5, dmic6,
-	gpio1, gpio2, ..., gpio40
-    The gpioN groups select the single pin of this name for configuration
-
-Optional properties of configuration subnodes:
-  Any configuration option not explicitly listed in the dts will be left at
-  chip default setting.
-
-  - function : name of function to assign to this group. One of:
-	aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2,
-	dmic3, dmic4, dmic5, dmic6,
-	io, dsp-gpio, irq1, irq2,
-	fll1-clk, fll1-lock, fll2-clk, fll2-lock, fll3-clk, fll3-lock,
-	fllao-clk, fllao-lock,
-	opclk, opclk-async, pwm1, pwm2, spdif,
-	asrc1-in1-lock, asrc1-in2-lock, asrc2-in1-lock, asrc2-in2-lock,
-	spkl-short-circuit, spkr-short-circuit, spk-shutdown,
-	spk-overheat-shutdown, spk-overheat-warn,
-	timer1-sts, timer2-sts, timer3-sts, timer4-sts, timer5-sts, timer6-sts,
-	timer7-sts, timer8-sts,
-	log1-fifo-ne, log2-fifo-ne, log3-fifo-ne, log4-fifo-ne, log5-fifo-ne,
-	log6-fifo-ne, log7-fifo-ne, log8-fifo-ne,
-
-  - bias-disable : disable pull-up and pull-down
-  - bias-bus-hold : enable buskeeper
-  - bias-pull-up : output is pulled-up
-  - bias-pull-down : output is pulled-down
-  - drive-push-pull : CMOS output
-  - drive-open-drain : open-drain output
-  - drive-strength : drive strength in mA. Valid values are 4 or 8
-  - input-schmitt-enable : enable schmitt-trigger mode
-  - input-schmitt-disable : disable schmitt-trigger mode
-  - input-debounce : A value of 0 disables debounce, a value !=0 enables
-	debounce
-  - output-low : set the pin to output mode with low level
-  - output-high : set the pin to output mode with high level
-
-Example:
-
-cs47l85@0 {
-	compatible = "cirrus,cs47l85";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&cs47l85_defaults>;
-
-	cs47l85_defaults: cs47l85-gpio-defaults {
-		aif1 {
-			groups = "aif1";
-			function = "aif1";
-			bias-bus-hold;
-		};
-
-		aif2 {
-			groups = "aif2";
-			function = "aif2";
-			bias-bus-hold;
-		};
-
-		opclk {
-			groups = "gpio1";
-			function = "opclk";
-			bias-pull-up;
-			drive-strength = <8>;
-		};
-	};
-};