diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
8 files changed, 256 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index 3297c53cb915..7aa9b1fa6b21 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -5,6 +5,10 @@ Required properties: - compatible: must be "dlg,da9210" - reg: the i2c slave address of the regulator. It should be 0x68. +Optional properties: + +- interrupts: a reference to the DA9210 interrupt, if available. + Any standard regulator properties can be used to configure the single da9210 DCDC. diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index eb618907c7de..c620493e8dbe 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,7 +1,7 @@ -* Dialog Semiconductor DA9211/DA9213 Voltage Regulator +* Dialog Semiconductor DA9211/DA9213/DA9215 Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9213". +- compatible: "dlg,da9211" or "dlg,da9213" or "dlg,da9215" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -66,3 +66,31 @@ Example 2) DA9213 }; }; }; + + +Example 3) DA9215 + pmic: da9215@68 { + compatible = "dlg,da9215"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/regulator/max77686.txt b/Documentation/devicetree/bindings/regulator/max77686.txt new file mode 100644 index 000000000000..0dded64d89d3 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77686.txt @@ -0,0 +1,71 @@ +Binding for Maxim MAX77686 regulators + +This is a part of the device tree bindings of MAX77686 multi-function device. +More information can be found in ../mfd/max77686.txt file. + +The MAX77686 PMIC has 9 high-efficiency Buck and 26 Low-DropOut (LDO) +regulators that can be controlled over I2C. + +Following properties should be present in main device node of the MFD chip. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator node's name should be initialized with a string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) + +Example: + + max77686: pmic@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 IRQ_TYPE_NONE>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt index 55efb24e5683..f80ea2fe27e6 100644 --- a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -25,6 +25,12 @@ Optional properties: -maxim,enable-frequency-shift: boolean, enable 9% frequency shift. -maxim,enable-bias-control: boolean, enable bias control. By enabling this startup delay can be reduce to 20us from 220us. +-maxim,enable-etr: boolean, enable Enhanced Transient Response. +-maxim,enable-high-etr-sensitivity: boolean, Enhanced transient response + circuit is enabled and set for high sensitivity. If this + property is available then etr will be enable default. + +Enhanced transient response (ETR) will affect the configuration of CKADV. Example: diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt new file mode 100644 index 000000000000..02649d8b3f5a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt @@ -0,0 +1,35 @@ +Mediatek MT6311 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6311-regulator" +- reg: I2C slave address, usually 0x6b. +- regulators: List of regulators provided by this controller. It is named + to VDVFS and VBIASN. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + VDVFS +LDO: + VBIASN + +Example: + mt6311: pmic@6b { + compatible = "mediatek,mt6311-regulator"; + reg = <0x6b>; + + regulators { + mt6311_vcpu_reg: VDVFS { + regulator-name = "VDVFS"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <10000>; + }; + mt6311_ldo_reg: VBIASN { + regulator-name = "VBIASN"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <800000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ce91f61feb12..ed936f0f34f2 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -1,27 +1,68 @@ -pwm regulator bindings +Bindings for the Generic PWM Regulator +====================================== + +Currently supports 2 modes of operation: + +Voltage Table: When in this mode, a voltage table (See below) of + predefined voltage <=> duty-cycle values must be + provided via DT. Limitations are that the regulator can + only operate at the voltages supplied in the table. + Intermediary duty-cycle values which would normally + allow finer grained voltage selection are ignored and + rendered useless. Although more control is given to + the user if the assumptions made in continuous-voltage + mode do not reign true. + +Continuous Voltage: This mode uses the regulator's maximum and minimum + supplied voltages specified in the + regulator-{min,max}-microvolt properties to calculate + appropriate duty-cycle values. This allows for a much + more fine grained solution when compared with + voltage-table mode above. This solution does make an + assumption that a %50 duty-cycle value will cause the + regulator voltage to run at half way between the + supplied max_uV and min_uV values. Required properties: -- compatible: Should be "pwm-regulator" -- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) -- voltage-table: voltage and duty table, include 2 members in each set of - brackets, first one is voltage(unit: uv), the next is duty(unit: percent) +-------------------- +- compatible: Should be "pwm-regulator" + +- pwms: PWM specification (See: ../pwm/pwm.txt) + +Only required for Voltage Table Mode: +- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells + First cell is voltage in microvolts (uV) + Second cell is duty-cycle in percent (%) + +NB: To be clear, if voltage-table is provided, then the device will be used +in Voltage Table Mode. If no voltage-table is provided, then the device will +be used in Continuous Voltage Mode. -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. +Any property defined as part of the core regulator binding can also be used. +(See: ../regulator/regulator.txt) -Example: +Continuous Voltage Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; +Voltage Table Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + + /* Voltage Duty-Cycle */ voltage-table = <1114000 0>, <1095000 10>, <1076000 20>, <1056000 30>, <1036000 40>, <1016000 50>; - - regulator-min-microvolt = <1016000>; - regulator-max-microvolt = <1114000>; - regulator-name = "vdd_logic"; }; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 75b4604bad07..d00bfd8624a5 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -91,13 +91,65 @@ see regulator.txt - with additional custom properties described below: - regulator-initial-mode: Usage: optional Value type: <u32> - Descrption: 1 = Set initial mode to high power mode (HPM), also referred - to as NPM. HPM consumes more ground current than LPM, but + Description: 2 = Set initial mode to auto mode (automatically select + between HPM and LPM); not available on boost type + regulators. + + 1 = Set initial mode to high power mode (HPM), also referred + to as NPM. HPM consumes more ground current than LPM, but it can source significantly higher load current. HPM is not available on boost type regulators. For voltage switch type regulators, HPM implies that over current protection and - soft start are active all the time. 0 = Set initial mode to - low power mode (LPM). + soft start are active all the time. + + 0 = Set initial mode to low power mode (LPM). + +- qcom,ocp-max-retries: + Usage: optional + Value type: <u32> + Description: Maximum number of times to try toggling a voltage switch + off and back on as a result of consecutive over current + events. + +- qcom,ocp-retry-delay: + Usage: optional + Value type: <u32> + Description: Time to delay in milliseconds between each voltage switch + toggle after an over current event takes place. + +- qcom,pin-ctrl-enable: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + enable the regulator, if any; supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + +- qcom,pin-ctrl-hpm: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + force the regulator into high power mode, if any; + supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + BIT(4) = follow PMIC awake state + +- qcom,vs-soft-start-strength: + Usage: optional + Value type: <u32> + Description: This property sets the soft start strength for voltage + switch type regulators; supported values are: + 0 = 0.05 uA + 1 = 0.25 uA + 2 = 0.55 uA + 3 = 0.75 uA Example: diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index db88feb28c03..24bd422cecd5 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -42,6 +42,7 @@ Optional properties: - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. +- regulator-over-current-protection: Enable over current protection. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple |