11 files changed, 237 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
index a1ee681942cc..6113f9275f42 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
@@ -4,7 +4,7 @@
 Required properties :
 
  - reg             : Offset and length of the register set for the device
- - compatible      : Should be "marvell,mv64xxx-i2c"
+ - compatible      : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c"
  - interrupts      : The interrupt number
 
 Optional properties :
diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
index 38e51ad2e07e..a45ae08c8ed1 100644
--- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -7,9 +7,30 @@ Required properties:
 - reg: Should contain SSC registers location and length
 - interrupts: Should contain SSC interrupt
 
-Example:
+
+Required properties for devices compatible with "atmel,at91sam9g45-ssc":
+- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+  the memory interface and SSC DMA channel ID (for tx and rx).
+  See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
+- dma-names: Must be "tx", "rx".
+
+Examples:
+- PDC transfer:
 ssc0: ssc@fffbc000 {
 	compatible = "atmel,at91rm9200-ssc";
 	reg = <0xfffbc000 0x4000>;
 	interrupts = <14 4 5>;
 };
+
+- DMA transfer:
+ssc0: ssc@f0010000 {
+      compatible = "atmel,at91sam9g45-ssc";
+      reg = <0xf0010000 0x4000>;
+      interrupts = <28 4 5>;
+      dmas = <&dma0 1 13>,
+	     <&dma0 1 14>;
+      dma-names = "tx", "rx";
+      pinctrl-names = "default";
+      pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+      status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
index d5a308629c57..30b0581bb1ce 100644
--- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
+++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
@@ -31,9 +31,8 @@ Optional nodes:
 	       Optional sub-node properties:
 	       ti,warm-reset - maintain voltage during warm reset(boolean)
 	       ti,roof-floor - control voltage selection by pin(boolean)
-	       ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto,
+	       ti,mode-sleep - mode to adopt in pmic sleep 0 - off, 1 - auto,
 	       2 - eco, 3 - forced pwm
-	       ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us
 	       ti,smps-range - OTP has the wrong range set for the hardware so override
 	       0 - low range, 1 - high range.
 
@@ -59,7 +58,6 @@ pmic {
 			ti,warm-reset;
 			ti,roof-floor;
 			ti,mode-sleep = <0>;
-			ti,tstep = <0>;
 			ti,smps-range = <1>;
 		};
 
diff --git a/Documentation/devicetree/bindings/sound/ak4554.c b/Documentation/devicetree/bindings/sound/ak4554.c
new file mode 100644
index 000000000000..934fa02754b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/ak4554.c
@@ -0,0 +1,11 @@
+AK4554 ADC/DAC
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4554"
+
+Example:
+
+ak4554-adc-dac {
+	compatible = "asahi-kasei,ak4554";
+};
diff --git a/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt b/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt
new file mode 100644
index 000000000000..0720857089a7
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt
@@ -0,0 +1,35 @@
+* Atmel at91sam9x5ek wm8731 audio complex
+
+Required properties:
+  - compatible: "atmel,sam9x5-wm8731-audio"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8731 audio codec
+  - atmel,audio-routing: A list of the connections between audio components.
+    Each entry is a pair of strings, the first being the connection's sink,
+    the second being the connection's source.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headphone Jack
+ * Line In Jack
+
+wm8731 pins:
+cf Documentation/devicetree/bindings/sound/wm8731.txt
+
+Example:
+sound {
+	compatible = "atmel,sam9x5-wm8731-audio";
+
+	atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+	atmel,audio-routing =
+		"Headphone Jack", "RHPOUT",
+		"Headphone Jack", "LHPOUT",
+		"LLINEIN", "Line In Jack",
+		"RLINEIN", "Line In Jack";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8731>;
+};
diff --git a/Documentation/devicetree/bindings/sound/atmel-wm8904.txt b/Documentation/devicetree/bindings/sound/atmel-wm8904.txt
new file mode 100644
index 000000000000..8bbe50c884b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/atmel-wm8904.txt
@@ -0,0 +1,55 @@
+Atmel ASoC driver with wm8904 audio codec complex
+
+Required properties:
+  - compatible: "atmel,asoc-wm8904"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,audio-routing: A list of the connections between audio components.
+    Each entry is a pair of strings, the first being the connection's sink,
+    the second being the connection's source. Valid names for sources and
+    sinks are the WM8904's pins, and the jacks on the board:
+
+    WM8904 pins:
+
+    * IN1L
+    * IN1R
+    * IN2L
+    * IN2R
+    * IN3L
+    * IN3R
+    * HPOUTL
+    * HPOUTR
+    * LINEOUTL
+    * LINEOUTR
+    * MICBIAS
+
+    Board connectors:
+
+    * Headphone Jack
+    * Line In Jack
+    * Mic
+
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8904 audio codec
+
+Optional properties:
+  - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt
+
+Example:
+sound {
+	compatible = "atmel,asoc-wm8904";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pck0_as_mck>;
+
+	atmel,model = "wm8904 @ AT91SAM9N12EK";
+
+	atmel,audio-routing =
+		"Headphone Jack", "HPOUTL",
+		"Headphone Jack", "HPOUTR",
+		"IN2L", "Line In Jack",
+		"IN2R", "Line In Jack",
+		"Mic", "MICBIAS",
+		"IN1L", "Mic";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8904>;
+};
diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
new file mode 100644
index 000000000000..f2ae335670f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
@@ -0,0 +1,54 @@
+Freescale Sony/Philips Digital Interface Format (S/PDIF) Controller
+
+The Freescale S/PDIF audio block is a stereo transceiver that allows the
+processor to receive and transmit digital audio via an coaxial cable or
+a fibre cable.
+
+Required properties:
+
+  - compatible : Compatible list, must contain "fsl,imx35-spdif".
+
+  - reg : Offset and length of the register set for the device.
+
+  - interrupts : Contains the spdif interrupt.
+
+  - dmas : Generic dma devicetree binding as described in
+  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names : Two dmas have to be defined, "tx" and "rx".
+
+  - clocks : Contains an entry for each entry in clock-names.
+
+  - clock-names : Includes the following entries:
+	"core"		The core clock of spdif controller
+	"rxtx<0-7>"	Clock source list for tx and rx clock.
+			This clock list should be identical to
+			the source list connecting to the spdif
+			clock mux in "SPDIF Transceiver Clock
+			Diagram" of SoC reference manual. It
+			can also be referred to TxClk_Source
+			bit of register SPDIF_STC.
+
+Example:
+
+spdif: spdif@02004000 {
+	compatible = "fsl,imx35-spdif";
+	reg = <0x02004000 0x4000>;
+	interrupts = <0 52 0x04>;
+	dmas = <&sdma 14 18 0>,
+	       <&sdma 15 18 0>;
+	dma-names = "rx", "tx";
+
+	clocks = <&clks 197>, <&clks 3>,
+	       <&clks 197>, <&clks 107>,
+	       <&clks 0>, <&clks 118>,
+	       <&clks 62>, <&clks 139>,
+	       <&clks 0>;
+	clock-names = "core", "rxtx0",
+		"rxtx1", "rxtx2",
+		"rxtx3", "rxtx4",
+		"rxtx5", "rxtx6",
+		"rxtx7";
+
+	status = "okay";
+};
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt
index 5ff76c9c57d2..4303b6ab6208 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,ssi.txt
@@ -43,10 +43,22 @@ Required properties:
                     together.  This would still allow different sample sizes,
                     but not different sample rates.
 
+Required are also ac97 link bindings if ac97 is used. See
+Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary
+bindings.
+
 Optional properties:
 - codec-handle:     Phandle to a 'codec' node that defines an audio
                     codec connected to this SSI.  This node is typically
                     a child of an I2C or other control node.
+- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to
+		    filter the codec stream. This is necessary for some boards
+		    where an incompatible codec is connected to this SSI, e.g.
+		    on pca100 and pcm043.
+- dmas:		    Generic dma devicetree binding as described in
+		    Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names:	    Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq
+		    is not defined.
 
 Child 'codec' node required properties:
 - compatible:       Compatible list, contains the name of the codec
diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt
index 215aa9817213..f88a00e54c63 100644
--- a/Documentation/devicetree/bindings/sound/imx-audmux.txt
+++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt
@@ -5,6 +5,15 @@ Required properties:
   or "fsl,imx31-audmux" for the version firstly used on i.MX31.
 - reg : Should contain AUDMUX registers location and length
 
+An initial configuration can be setup using child nodes.
+
+Required properties of optional child nodes:
+- fsl,audmux-port : Integer of the audmux port that is configured by this
+  child node.
+- fsl,port-config : List of configuration options for the specific port. For
+  imx31-audmux and above, it is a list of tuples <ptcr pdcr>. For
+  imx21-audmux it is a list of pcr values.
+
 Example:
 
 audmux@021d8000 {
diff --git a/Documentation/devicetree/bindings/sound/soc-ac97link.txt b/Documentation/devicetree/bindings/sound/soc-ac97link.txt
new file mode 100644
index 000000000000..80152a87f239
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/soc-ac97link.txt
@@ -0,0 +1,28 @@
+AC97 link bindings
+
+These bindings can be included within any other device node.
+
+Required properties:
+ - pinctrl-names: Has to contain following states to setup the correct
+   pinmuxing for the used gpios:
+	"ac97-running": AC97-link is active
+	"ac97-reset": AC97-link reset state
+	"ac97-warm-reset": AC97-link warm reset state
+ - ac97-gpios: List of gpio phandles with args in the order ac97-sync,
+   ac97-sdata, ac97-reset
+
+
+Example:
+
+ssi {
+	...
+
+	pinctrl-names = "default", "ac97-running", "ac97-reset", "ac97-warm-reset";
+	pinctrl-0 = <&ac97link_running>;
+	pinctrl-1 = <&ac97link_running>;
+	pinctrl-2 = <&ac97link_reset>;
+	pinctrl-3 = <&ac97link_warm_reset>;
+	ac97-gpios = <&gpio3 20 0 &gpio3 22 0 &gpio3 28 0>;
+
+	...
+};
diff --git a/Documentation/devicetree/bindings/sound/wm8731.txt b/Documentation/devicetree/bindings/sound/wm8731.txt
index 15f70048469b..236690e99b87 100644
--- a/Documentation/devicetree/bindings/sound/wm8731.txt
+++ b/Documentation/devicetree/bindings/sound/wm8731.txt
@@ -16,3 +16,12 @@ codec: wm8731@1a {
 	compatible = "wlf,wm8731";
 	reg = <0x1a>;
 };
+
+Available audio endpoints for an audio-routing table:
+ * LOUT: Left Channel Line Output
+ * ROUT: Right Channel Line Output
+ * LHPOUT: Left Channel Headphone Output
+ * RHPOUT: Right Channel Headphone Output
+ * LLINEIN: Left Channel Line Input
+ * RLINEIN: Right Channel Line Input
+ * MICIN: Microphone Input