diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 130 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt new file mode 100644 index 000000000000..855e1faf73e2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -0,0 +1,63 @@ +SMIA/SMIA++ sensor + +SMIA (Standard Mobile Imaging Architecture) is an image sensor standard +defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension +of that. These definitions are valid for both types of sensors. + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "nokia,smia" +- reg: I2C address (0x10, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor + dependent). +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor +- link-frequencies: List of allowed data link frequencies. An array of + 64-bit elements. + + +Optional properties +------------------- + +- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, + the NVM contents will not be read. +- reset-gpios: XSHUTDOWN GPIO + + +Endpoint node mandatory properties +---------------------------------- + +- clock-lanes: <0> +- data-lanes: <1..n> +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c2 { + clock-frequency = <400000>; + + smiapp_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + reset-gpios = <&gpio3 20 0>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <512>; /* 8 * 64 */ + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + port { + smiapp_1_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt index 23dd5ad07b7c..1811a067c72c 100644 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -1,7 +1,7 @@ Device-Tree bindings for SUNXI IR controller found in sunXi SoC family Required properties: -- compatible : should be "allwinner,sun4i-a10-ir"; +- compatible : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir" - clocks : list of clock specifiers, corresponding to entries in clock-names property; - clock-names : should contain "apb" and "ir" entries; @@ -10,6 +10,7 @@ Required properties: Optional properties: - linux,rc-map-name : Remote control map name. +- resets : phandle + reset specifier pair Example: @@ -17,6 +18,7 @@ ir0: ir@01c21800 { compatible = "allwinner,sun4i-a10-ir"; clocks = <&apb0_gates 6>, <&ir0_clk>; clock-names = "apb", "ir"; + resets = <&apb0_rst 1>; interrupts = <0 5 1>; reg = <0x01C21800 0x40>; linux,rc-map-name = "rc-rc6-mce"; diff --git a/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt new file mode 100644 index 000000000000..3932e766553a --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt @@ -0,0 +1,61 @@ +Texas Instruments AM437x CAMERA (VPFE) +-------------------------------------- + +The Video Processing Front End (VPFE) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect RAW image-sensor modules and video decoders +to the AM437x device. + +Required properties: +- compatible: must be "ti,am437x-vpfe" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPFE; +- ti,am437x-vpfe-interface: can be one of the following, + 0 - Raw Bayer Interface. + 1 - 8 Bit BT656 Interface. + 2 - 10 Bit BT656 Interface. + 3 - YCbCr 8 Bit Interface. + 4 - YCbCr 16 Bit Interface. + +VPFE supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + vpfe: vpfe@f0034000 { + compatible = "ti,am437x-vpfe"; + reg = <0x48328000 0x2000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&vpfe_pins_default>; + pinctrl-1 = <&vpfe_pins_sleep>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vpfe0_ep: endpoint { + remote-endpoint = <&ov2659_1>; + ti,am437x-vpfe-interface = <0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; + + i2c1: i2c@4802a000 { + + ov2659@30 { + compatible = "ti,ov2659"; + reg = <0x30>; + + port { + ov2659_1: endpoint { + remote-endpoint = <&vpfe0_ep>; + bus-width = <8>; + mclk-frequency = <12000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index ce719f89dd1c..52a14cf099ac 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -103,6 +103,9 @@ Optional endpoint properties array contains only one entry. - clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous clock mode. +- link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for + instance, this is the actual frequency of the bus, not bits per clock per + lane value. An array of 64-bit unsigned integers. Example |