diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
7 files changed, 27 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index d3d0a4fb1c73..079b42a81d7c 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -22,8 +22,7 @@ Required properties: Optional properties: - ti,hwmods: Name of the hwmods associated to the eDMA CC - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow - these channels will be SW triggered channels. The list must - contain 16 bits numbers, see example. + these channels will be SW triggered channels. See example. - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by the driver, they are allocated to be used by for example the DSP. See example. @@ -56,10 +55,9 @@ edma: edma@49000000 { ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>; /* Channel 20 and 21 is allocated for memcpy */ - ti,edma-memcpy-channels = /bits/ 16 <20 21>; - /* The following PaRAM slots are reserved: 35-45 and 100-110 */ - ti,edma-reserved-slot-ranges = /bits/ 16 <35 10>, - /bits/ 16 <100 10>; + ti,edma-memcpy-channels = <20 21>; + /* The following PaRAM slots are reserved: 35-44 and 100-109 */ + ti,edma-reserved-slot-ranges = <35 10>, <100 10>; }; edma_tptc0: tptc@49800000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index f2455c50533d..120bc4971cf3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -11,6 +11,10 @@ Required properties: 0 = active high 1 = active low +Optional properties: +- little-endian : GPIO registers are used as little endian. If not + present registers are used as big endian by default. + Example: gpio0: gpio@1100 { diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt index b9c32f6fd687..4357e498ef04 100644 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -12,7 +12,7 @@ Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": Required subnode-properties: - label: Descriptive name of the key. - linux,code: Keycode to emit. - - channel: Channel this key is attached to, mut be 0 or 1. + - channel: Channel this key is attached to, must be 0 or 1. - voltage: Voltage in µV at lradc input when this key is pressed. Example: diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index f1e2a02381a4..1c63e40659fc 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -6,7 +6,9 @@ used for what purposes, but which don't use an on-flash partition table such as RedBoot. The partition table should be a subnode of the mtd node and should be named -'partitions'. Partitions are defined in subnodes of the partitions node. +'partitions'. This node should have the following property: +- compatible : (required) must be "fixed-partitions" +Partitions are then defined in subnodes of the partitions node. For backwards compatibility partitions as direct subnodes of the mtd device are supported. This use is discouraged. @@ -36,6 +38,7 @@ Examples: flash@0 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; @@ -53,6 +56,7 @@ flash@0 { flash@1 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <2>; @@ -66,6 +70,7 @@ flash@1 { flash@2 { partitions { + compatible = "fixed-partitions"; #address-cells = <2>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 9853f8e70966..28a4781ab6d7 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -40,18 +40,18 @@ Optional properties: Slave Properties: Required properties: -- phy_id : Specifies slave phy id - phy-mode : See ethernet.txt file in the same directory Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy_id : Specifies slave phy id - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the properties phy_id and phy-mode, - or the sub-node fixed-link can be specified + Either the property phy_id, or the sub-node + fixed-link can be specified Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index f5a8ca29aff0..aeea50c84e92 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -8,6 +8,11 @@ Required properties: - phy-mode: See ethernet.txt file in the same directory - clocks: a pointer to the reference clock for this device. +Optional properties: +- tx-csum-limit: maximum mtu supported by port that allow TX checksum. + Value is presented in bytes. If not used, by default 1600B is set for + "marvell,armada-370-neta" and 9800B for others. + Example: ethernet@d0070000 { @@ -15,6 +20,7 @@ ethernet@d0070000 { reg = <0xd0070000 0x2500>; interrupts = <8>; clocks = <&gate_clk 4>; + tx-csum-limit = <9800> status = "okay"; phy = <&phy0>; phy-mode = "rgmii-id"; diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index b38200d2583a..0dfa60d88dd3 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -1,7 +1,9 @@ * Temperature Sensor ADC (TSADC) on rockchip SoCs Required properties: -- compatible : "rockchip,rk3288-tsadc" +- compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3368-tsadc": found on RK3368 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format |