diff options
Diffstat (limited to 'Documentation/devicetree')
15 files changed, 234 insertions, 48 deletions
diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt index 4b87ea1194e3..704be9306c9f 100644 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -95,7 +95,6 @@ GPMC chip-select settings properties for child nodes. All are optional. - gpmc,burst-wrap Enables wrap bursting - gpmc,burst-read Enables read page/burst mode - gpmc,burst-write Enables write page/burst mode -- gpmc,device-nand Device is NAND - gpmc,device-width Total width of device(s) connected to a GPMC chip-select in bytes. The GPMC supports 8-bit and 16-bit devices and so this property must be diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt new file mode 100644 index 000000000000..bea5b73a7390 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -0,0 +1,66 @@ +* DMA40 DMA Controller + +Required properties: +- compatible: "stericsson,dma40" +- reg: Address range of the DMAC registers +- reg-names: Names of the above areas to use during resource look-up +- interrupt: Should contain the DMAC interrupt number +- #dma-cells: must be <3> +- memcpy-channels: Channels to be used for memcpy + +Optional properties: +- dma-channels: Number of channels supported by hardware - if not present + the driver will attempt to obtain the information from H/W +- disabled-channels: Channels which can not be used + +Example: + + dma: dma-controller@801C0000 { + compatible = "stericsson,db8500-dma40", "stericsson,dma40"; + reg = <0x801C0000 0x1000 0x40010000 0x800>; + reg-names = "base", "lcpa"; + interrupt-parent = <&intc>; + interrupts = <0 25 0x4>; + + #dma-cells = <2>; + memcpy-channels = <56 57 58 59 60>; + disabled-channels = <12>; + dma-channels = <8>; + }; + +Clients +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: + 1. A phandle pointing to the DMA controller + 2. Device Type + 3. The DMA request line number (only when 'use fixed channel' is set) + 4. A 32bit mask specifying; mode, direction and endianess [NB: This list will grow] + 0x00000001: Mode: + Logical channel when unset + Physical channel when set + 0x00000002: Direction: + Memory to Device when unset + Device to Memory when set + 0x00000004: Endianess: + Little endian when unset + Big endian when set + 0x00000008: Use fixed channel: + Use automatic channel selection when unset + Use DMA request line number when set + +Example: + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ + <&dma 13 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "rx"; + + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index f1e5dfecf55d..5375625e8cd2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,46 +39,3 @@ Example: #gpio-cells = <4>; gpio-controller; }; - - -Samsung S3C24XX GPIO Controller - -Required properties: -- compatible: Compatible property value should be "samsung,s3c24xx-gpio". - -- reg: Physical base address of the controller and length of memory mapped - region. - -- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes - should be the following with values derived from the SoC user manual. - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [mux function] - [flags and pull up/down] - - Values for gpio specifier: - - Pin number: depending on the controller a number from 0 up to 15. - - Mux function: Depending on the SoC and the gpio bank the gpio can be set - as input, output or a special function - - Flags and Pull Up/Down: the values to use differ for the individual SoCs - example S3C2416/S3C2450: - 0 - Pull Up/Down Disabled. - 1 - Pull Down Enabled. - 2 - Pull Up Enabled. - Bit 16 (0x00010000) - Input is active low. - Consult the user manual for the correct values of Mux and Pull Up/Down. - -- gpio-controller: Specifies that the node is a gpio controller. -- #address-cells: should be 1. -- #size-cells: should be 1. - -Example: - - gpa: gpio-controller@56000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "samsung,s3c24xx-gpio"; - reg = <0x56000000 0x10>; - #gpio-cells = <3>; - gpio-controller; - }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt new file mode 100644 index 000000000000..46d76a004246 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -0,0 +1,52 @@ +* Renesas R-Car GPIO Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. + - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. + - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. + - "renesas,gpio-rcar": for generic R-Car GPIO controller. + + - reg: Base address and length of each memory resource used by the GPIO + controller hardware module. + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell is used to specify optional parameters as bit flags. Only the GPIO + active low flag (bit 0) is currently supported. + - gpio-ranges: Range of pins managed by the GPIO controller as a 4-cells + tuple using the following syntax. + + <[phandle of the pin controller node] + 0 + [index of the first pin] + [number of pins]> + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: R8A7779 (R-Car H1) GPIO controller nodes + + gpio0: gpio@ffc40000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc40000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 141 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + }; + ... + gpio6: gpio@ffc46000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc46000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 147 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 9>; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 6a983c1d87cd..df338cb5059c 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -29,6 +29,13 @@ Optional properties: "bch4" 4-bit BCH ecc code "bch8" 8-bit BCH ecc code + - ti,nand-xfer-type: A string setting the data transfer type. One of: + + "prefetch-polled" Prefetch polled mode (default) + "polled" Polled mode, without prefetch + "prefetch-dma" Prefetch enabled sDMA mode + "prefetch-irq" Prefetch enabled irq mode + - elm_id: Specifies elm device node. This is required to support BCH error correction using ELM module. @@ -55,6 +62,7 @@ Example for an AM33xx board: reg = <0 0 0>; /* CS0, offset 0 */ nand-bus-width = <16>; ti,nand-ecc-opt = "bch8"; + ti,nand-xfer-type = "polled"; gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 44afa0e5057d..4ff65047bb9a 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". - Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on + Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index c70fca146e91..b2bc219e2003 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -7,6 +7,10 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. + - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller, + - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller, + - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller, + - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. @@ -106,6 +110,10 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - compatible: identifies the type of the external wakeup interrupt controller The possible values are: + - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C24xx SoCs except S3C2412 and S3C2413, + - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C2412 and S3C2413 SoCs, - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller found on Samsung S3C64xx SoCs, - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller diff --git a/Documentation/devicetree/bindings/rtc/dw-apb.txt b/Documentation/devicetree/bindings/rtc/dw-apb.txt index 93e2b0f048e6..eb2327b2bdb3 100644 --- a/Documentation/devicetree/bindings/rtc/dw-apb.txt +++ b/Documentation/devicetree/bindings/rtc/dw-apb.txt @@ -5,9 +5,20 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: IRQ line for the timer. +- either clocks+clock-names or clock-frequency properties + +Optional properties: +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names : should contain "timer" and "pclk" entries, matching entries + in the clocks property. - clock-frequency: The frequency in HZ of the timer. - clock-freq: For backwards compatibility with picoxcell +If using the clock specifiers, the pclk clock is optional, as not all +systems may use one. + + Example: timer1: timer@ffc09000 { @@ -23,3 +34,11 @@ Example: clock-frequency = <200000000>; reg = <0xffd00000 0x1000>; }; + + timer3: timer@ffe00000 { + compatible = "snps,dw-apb-timer-osc"; + interrupts = <0 170 4>; + reg = <0xffe00000 0x1000>; + clocks = <&timer_clk>, <&timer_pclk>; + clock-names = "timer", "pclk"; + }; diff --git a/Documentation/devicetree/bindings/usb/ux500-usb.txt b/Documentation/devicetree/bindings/usb/ux500-usb.txt new file mode 100644 index 000000000000..330d6ec15401 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ux500-usb.txt @@ -0,0 +1,50 @@ +Ux500 MUSB + +Required properties: + - compatible : Should be "stericsson,db8500-musb" + - reg : Offset and length of registers + - interrupts : Interrupt; mode, number and trigger + - dr_mode : Dual-role; either host mode "host", peripheral mode "peripheral" + or both "otg" + +Optional properties: + - dmas : A list of dma channels; + dma-controller, event-line, fixed-channel, flags + - dma-names : An ordered list of channel names affiliated to the above + +Example: + +usb_per5@a03e0000 { + compatible = "stericsson,db8500-musb", "mentor,musb"; + reg = <0xa03e0000 0x10000>; + interrupts = <0 23 0x4>; + interrupt-names = "mc"; + + dr_mode = "otg"; + + dmas = <&dma 38 0 0x2>, /* Logical - DevToMem */ + <&dma 38 0 0x0>, /* Logical - MemToDev */ + <&dma 37 0 0x2>, /* Logical - DevToMem */ + <&dma 37 0 0x0>, /* Logical - MemToDev */ + <&dma 36 0 0x2>, /* Logical - DevToMem */ + <&dma 36 0 0x0>, /* Logical - MemToDev */ + <&dma 19 0 0x2>, /* Logical - DevToMem */ + <&dma 19 0 0x0>, /* Logical - MemToDev */ + <&dma 18 0 0x2>, /* Logical - DevToMem */ + <&dma 18 0 0x0>, /* Logical - MemToDev */ + <&dma 17 0 0x2>, /* Logical - DevToMem */ + <&dma 17 0 0x0>, /* Logical - MemToDev */ + <&dma 16 0 0x2>, /* Logical - DevToMem */ + <&dma 16 0 0x0>, /* Logical - MemToDev */ + <&dma 39 0 0x2>, /* Logical - DevToMem */ + <&dma 39 0 0x0>; /* Logical - MemToDev */ + + dma-names = "iep_1_9", "oep_1_9", + "iep_2_10", "oep_2_10", + "iep_3_11", "oep_3_11", + "iep_4_12", "oep_4_12", + "iep_5_13", "oep_5_13", + "iep_6_14", "oep_6_14", + "iep_7_15", "oep_7_15", + "iep_8", "oep_8"; +}; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 589edee37394..589edee37394 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt index fa166d945809..fa166d945809 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt index 858f4f9b902f..858f4f9b902f 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 9b2ea0343566..9b2ea0343566 100644 --- a/Documentation/devicetree/bindings/drm/exynos/mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt diff --git a/Documentation/devicetree/bindings/video/simple-framebuffer.txt b/Documentation/devicetree/bindings/video/simple-framebuffer.txt new file mode 100644 index 000000000000..3ea460583111 --- /dev/null +++ b/Documentation/devicetree/bindings/video/simple-framebuffer.txt @@ -0,0 +1,25 @@ +Simple Framebuffer + +A simple frame-buffer describes a raw memory region that may be rendered to, +with the assumption that the display hardware has already been set up to scan +out from that buffer. + +Required properties: +- compatible: "simple-framebuffer" +- reg: Should contain the location and size of the framebuffer memory. +- width: The width of the framebuffer in pixels. +- height: The height of the framebuffer in pixels. +- stride: The number of bytes in each line of the framebuffer. +- format: The format of the framebuffer surface. Valid values are: + - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). + +Example: + + framebuffer { + compatible = "simple-framebuffer"; + reg = <0x1d385000 (1600 * 1200 * 2)>; + width = <1600>; + height = <1200>; + stride = <(1600 * 2)>; + format = "r5g6b5"; + }; diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt index ef9d06c9f8fd..0efedaad5165 100644 --- a/Documentation/devicetree/usage-model.txt +++ b/Documentation/devicetree/usage-model.txt @@ -191,9 +191,11 @@ Linux it will look something like this: }; The bootargs property contains the kernel arguments, and the initrd-* -properties define the address and size of an initrd blob. The -chosen node may also optionally contain an arbitrary number of -additional properties for platform-specific configuration data. +properties define the address and size of an initrd blob. Note that +initrd-end is the first address after the initrd image, so this doesn't +match the usual semantic of struct resource. The chosen node may also +optionally contain an arbitrary number of additional properties for +platform-specific configuration data. During early boot, the architecture setup code calls of_scan_flat_dt() several times with different helper callbacks to parse device tree |