diff options
Diffstat (limited to 'Documentation/devicetree')
16 files changed, 342 insertions, 59 deletions
diff --git a/Documentation/devicetree/bindings/misc/allwinner,syscon.txt b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt new file mode 100644 index 000000000000..31494a24fe69 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt @@ -0,0 +1,20 @@ +* Allwinner sun8i system controller + +This file describes the bindings for the system controller present in +Allwinner SoC H3, A83T and A64. +The principal function of this syscon is to control EMAC PHY choice and +config. + +Required properties for the system controller: +- reg: address and length of the register for the device. +- compatible: should be "syscon" and one of the following string: + "allwinner,sun8i-h3-system-controller" + "allwinner,sun8i-v3s-system-controller" + "allwinner,sun50i-a64-system-controller" + "allwinner,sun8i-a83t-system-controller" + +Example: +syscon: syscon@1c00000 { + compatible = "allwinner,sun8i-h3-system-controller", "syscon"; + reg = <0x01c00000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/net/cortina.txt b/Documentation/devicetree/bindings/net/cortina.txt new file mode 100644 index 000000000000..40d0bd984113 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cortina.txt @@ -0,0 +1,21 @@ +Cortina Phy Driver Device Tree Bindings +--------------------------------------- + +CORTINA is a registered trademark of Cortina Systems, Inc. + +The driver supports the Cortina Electronic Dispersion Compensation (EDC) +devices, equipped with clock and data recovery (CDR) circuits. These +devices make use of registers that are not compatible with Clause 45 or +Clause 22, therefore they need to be described using the +"ethernet-phy-id" compatible. + +Since the driver only implements polling mode support, interrupts info +can be skipped. + +Example (CS4340 phy): + mdio { + cs4340_phy@10 { + compatible = "ethernet-phy-id13e5.1002"; + reg = <0x10>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 8ec2ca21adeb..8acf51a4dfa8 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -13,6 +13,9 @@ Required properties: "brcm,bcm5397" "brcm,bcm5398" + For the BCM11360 SoC, must be: + "brcm,bcm11360-srab" and the mandatory "brcm,cygnus-srab" string + For the BCM5310x SoCs with an integrated switch, must be one of: "brcm,bcm53010-srab" "brcm,bcm53011-srab" diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt new file mode 100644 index 000000000000..0ab8b39d0b30 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -0,0 +1,72 @@ +Microchip KSZ Series Ethernet switches +================================== + +Required properties: + +- compatible: For external switch chips, compatible string must be exactly one + of: "microchip,ksz9477" + +See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +required and optional properties. + +Examples: + +Ethernet switch connected via SPI to the host, CPU port wired to eth0: + + eth0: ethernet@10001000 { + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + spi1: spi@f8008000 { + pinctrl-0 = <&pinctrl_spi_ksz>; + cs-gpios = <&pioC 25 0>; + id = <1>; + status = "okay"; + + ksz9477: ksz9477@0 { + compatible = "microchip,ksz9477"; + reg = <0>; + + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; + + status = "okay"; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "lan5"; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt new file mode 100644 index 000000000000..725f3b187886 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -0,0 +1,84 @@ +* Allwinner sun8i GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: +- compatible: should be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun8i-v3s-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- interrupts: interrupt for the device +- interrupt-names: should be "macirq" +- clocks: A phandle to the reference clock for this device +- clock-names: should be "stmmaceth" +- resets: A phandle to the reset control for this device +- reset-names: should be "stmmaceth" +- phy-mode: See ethernet.txt +- phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 +- syscon: A phandle to the syscon of the SoC with one of the following + compatible string: + - allwinner,sun8i-h3-system-controller + - allwinner,sun8i-v3s-system-controller + - allwinner,sun50i-a64-system-controller + - allwinner,sun8i-a83t-system-controller + +Optional properties: +- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0) +- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0) +Both delay properties need to be a multiple of 100. They control the delay for +external PHY. + +Optional properties for the following compatibles: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Required child node of emac: +- mdio bus node: should be named mdio + +Required properties of the mdio node: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +The device node referenced by "phy" or "phy-handle" should be a child node +of the mdio node. See phy.txt for the generic PHY bindings. + +Required properties of the phy node with the following compatibles: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": +- clocks: a phandle to the reference clock for the EPHY +- resets: a phandle to the reset control for the EPHY + +Example: + +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 3a6916909d90..edd7fd2bbbf9 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -11,6 +11,7 @@ The following properties are common to the Ethernet controllers: the maximum frame size (there's contradiction in ePAPR). - phy-mode: string, operation mode of the PHY interface. This is now a de-facto standard property; supported values are: + * "internal" * "mii" * "gmii" * "sgmii" @@ -32,6 +33,8 @@ The following properties are common to the Ethernet controllers: * "2000base-x", * "2500base-x", * "rxaui" + * "xaui" + * "10gbase-kr" (10GBASE-KR, XFI, SFI) - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 1506e948610c..27966ae741e0 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -22,6 +22,7 @@ Required properties: Required elements: 'pclk', 'hclk' Optional elements: 'tx_clk' Optional elements: 'rx_clk' applies to cdns,zynqmp-gem + Optional elements: 'tsu_clk' - clocks: Phandles to input clocks. Optional properties for PHY child node: diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt index ccdabdcc8618..42cd81090a2c 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -1,12 +1,14 @@ * Marvell MDIO Ethernet Controller interface The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x, -MV78xx0, Armada 370 and Armada XP have an identical unit that provides -an interface with the MDIO bus. This driver handles this MDIO -interface. +MV78xx0, Armada 370, Armada XP, Armada 7k and Armada 8k have an +identical unit that provides an interface with the MDIO bus. +Additionally, Armada 7k and Armada 8k has a second unit which +provides an interface with the xMDIO bus. This driver handles +these interfaces. Required properties: -- compatible: "marvell,orion-mdio" +- compatible: "marvell,orion-mdio" or "marvell,xmdio" - reg: address and length of the MDIO registers. When an interrupt is not present, the length is the size of the SMI register (4 bytes) otherwise it must be 0x84 bytes to cover the interrupt control diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt index c627bbb3009e..60c833d62181 100644 --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -13,14 +13,10 @@ Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. - autosuspend-delay: Specify autosuspend delay in milliseconds. -- vin-voltage-override: Specify voltage of VIN pin in microvolts. - irq-status-read-quirk: Specify that the trf7970a being used has the "IRQ Status Read" erratum. - en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" erratum. -- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum - where an extra byte is returned by Read Multiple Block commands issued - to Type 5 tags. - vdd-io-supply: Regulator specifying voltage for vdd-io - clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz @@ -37,15 +33,13 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1): spi-max-frequency = <2000000>; interrupt-parent = <&gpio2>; interrupts = <14 0>; - ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>, - <&gpio2 5 GPIO_ACTIVE_LOW>; + ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>, + <&gpio2 5 GPIO_ACTIVE_HIGH>; vin-supply = <&ldo3_reg>; - vin-voltage-override = <5000000>; vdd-io-supply = <&ldo2_reg>; autosuspend-delay = <30000>; irq-status-read-quirk; en2-rf-quirk; - t5t-rmb-extra-byte-quirk; clock-frequency = <27120000>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt new file mode 100644 index 000000000000..6d9efb2eb9a5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt @@ -0,0 +1,88 @@ +* Qualcomm QCA7000 + +The QCA7000 is a serial-to-powerline bridge with a host interface which could +be configured either as SPI or UART slave. This configuration is done by +the QCA7000 firmware. + +(a) Ethernet over SPI + +In order to use the QCA7000 as SPI device it must be defined as a child of a +SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source + interrupt and the second cell should specify the trigger + type as rising edge +- spi-cpha : Must be set +- spi-cpol : Must be set + +Optional properties: +- interrupt-parent : Specify the pHandle of the source interrupt +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 + are invalid. Missing the property will set the SPI + frequency to 8000000 Hertz. +- local-mac-address : see ./ethernet.txt +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select + between each data word. In burst mode these gaps aren't + necessary, which is faster. This setting depends on how + the QCA7000 is setup via GPIO pin strapping. If the + property is missing the driver defaults to burst mode. + +SPI Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; + +(b) Ethernet over UART + +In order to use the QCA7000 as UART slave it must be defined as a child of a +UART master in the device tree. It is possible to preconfigure the UART +settings of the QCA7000 firmware, but it's not possible to change them during +runtime. + +Required properties: +- compatible : Should be "qca,qca7000" + +Optional properties: +- local-mac-address : see ./ethernet.txt +- current-speed : current baud rate of QCA7000 which defaults to 115200 + if absent, see also ../serial/slave-device.txt + +UART Example: + +/* Freescale i.MX28 UART */ +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; + + qca7000: ethernet { + compatible = "qca,qca7000"; + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + current-speed = <38400>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt deleted file mode 100644 index c74989c0d8ac..000000000000 --- a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt +++ /dev/null @@ -1,47 +0,0 @@ -* Qualcomm QCA7000 (Ethernet over SPI protocol) - -Note: The QCA7000 is useable as a SPI device. In this case it must be defined -as a child of a SPI master in the device tree. - -Required properties: -- compatible : Should be "qca,qca7000" -- reg : Should specify the SPI chip select -- interrupts : The first cell should specify the index of the source interrupt - and the second cell should specify the trigger type as rising edge -- spi-cpha : Must be set -- spi-cpol: Must be set - -Optional properties: -- interrupt-parent : Specify the pHandle of the source interrupt -- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. - Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing - the property will set the SPI frequency to 8000000 Hertz. -- local-mac-address: 6 bytes, MAC address -- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. - In this mode the SPI master must toggle the chip select between each data - word. In burst mode these gaps aren't necessary, which is faster. - This setting depends on how the QCA7000 is setup via GPIO pin strapping. - If the property is missing the driver defaults to burst mode. - -Example: - -/* Freescale i.MX28 SPI master*/ -ssp2: spi@80014000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx28-spi"; - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - status = "okay"; - - qca7000: ethernet@0 { - compatible = "qca,qca7000"; - reg = <0x0>; - interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ - interrupts = <25 0x1>; /* Index: 25, rising edge */ - spi-cpha; /* SPI mode: CPHA=1 */ - spi-cpol; /* SPI mode: CPOL=1 */ - spi-max-frequency = <8000000>; /* freq: 8 MHz */ - local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; - }; -}; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index afe9630a5e7d..02c4353b5cf2 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -18,6 +18,13 @@ Optional property: - ti,max-output-impedance - MAC Interface Impedance control to set the programmable output impedance to maximum value (70 ohms). + - ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the + board has RX_DV/RX_CTRL pin strapped in + mode 1 or 2. To ensure PHY operation, + there are specific actions that + software needs to take when this pin is + strapped in these modes. See data manual + for details. Note: ti,min-output-impedance and ti,max-output-impedance are mutually exclusive. When both properties are present ti,max-output-impedance diff --git a/Documentation/devicetree/bindings/net/ti,wilink-st.txt b/Documentation/devicetree/bindings/net/ti,wilink-st.txt index cbad73a84ac4..1649c1f66b07 100644 --- a/Documentation/devicetree/bindings/net/ti,wilink-st.txt +++ b/Documentation/devicetree/bindings/net/ti,wilink-st.txt @@ -14,6 +14,12 @@ Required properties: - compatible: should be one of the following: "ti,wl1271-st" "ti,wl1273-st" + "ti,wl1281-st" + "ti,wl1283-st" + "ti,wl1285-st" + "ti,wl1801-st" + "ti,wl1805-st" + "ti,wl1807-st" "ti,wl1831-st" "ti,wl1835-st" "ti,wl1837-st" @@ -22,6 +28,10 @@ Optional properties: - enable-gpios : GPIO signal controlling enabling of BT. Active high. - vio-supply : Vio input supply (1.8V) - vbat-supply : Vbat input supply (2.9-4.8V) + - clocks : Must contain an entry, for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names : Must include the following entry: + "ext_clock" (External clock provided to the TI combo chip). Example: @@ -31,5 +41,7 @@ Example: bluetooth { compatible = "ti,wl1835-st"; enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + clocks = <&clk32k_wl18xx>; + clock-names = "ext_clock"; }; }; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt index 2a3d90de18ee..7b2cbb14113e 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -10,6 +10,7 @@ Required properties: * "ti,wl1273" * "ti,wl1281" * "ti,wl1283" + * "ti,wl1285" * "ti,wl1801" * "ti,wl1805" * "ti,wl1807" diff --git a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt new file mode 100644 index 000000000000..07590bcdad15 --- /dev/null +++ b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt @@ -0,0 +1,13 @@ +* Broadcom Digital Timing Engine(DTE) based PTP clock driver + +Required properties: +- compatible: should be "brcm,ptp-dte" +- reg: address and length of the DTE block's NCO registers + +Example: + +ptp_dte: ptp_dte@180af650 { + compatible = "brcm,ptp-dte"; + reg = <0x180af650 0x10>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/serial/slave-device.txt b/Documentation/devicetree/bindings/serial/slave-device.txt index f66037928f5f..40110e019620 100644 --- a/Documentation/devicetree/bindings/serial/slave-device.txt +++ b/Documentation/devicetree/bindings/serial/slave-device.txt @@ -21,6 +21,15 @@ Optional Properties: can support. For example, a particular board has some signal quality issue or the host processor can't support higher baud rates. +- current-speed : The current baud rate the device operates at. This should + only be present in case a driver has no chance to know + the baud rate of the slave device. + Examples: + * device supports auto-baud + * the rate is setup by a bootloader and there is no + way to reset the device + * device baud rate is configured by its firmware but + there is no way to request the actual settings Example: |