diff options
Diffstat (limited to 'Documentation/devicetree')
365 files changed, 10938 insertions, 609 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt new file mode 100644 index 000000000000..d0ce01da5c59 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt @@ -0,0 +1,15 @@ +Altera SOCFPGA SDRAM Error Detection & Correction [EDAC] +The EDAC accesses a range of registers in the SDRAM controller. + +Required properties: +- compatible : should contain "altr,sdram-edac"; +- altr,sdr-syscon : phandle of the sdr module +- interrupts : Should contain the SDRAM ECC IRQ in the + appropriate format for the IRQ controller. + +Example: + sdramedac { + compatible = "altr,sdram-edac"; + altr,sdr-syscon = <&sdr>; + interrupts = <0 39 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt new file mode 100644 index 000000000000..8fe815046140 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -0,0 +1,10 @@ +Amlogic MesonX device tree bindings +------------------------------------------- + +Boards with the Amlogic Meson6 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson6" + +Boards with the Amlogic Meson8 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8"; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 37b2cafa4e52..256b4d8bab7b 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -22,6 +22,14 @@ to deliver its interrupts via SPIs. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. +** Optional properties: + +- arm,cpu-registers-not-fw-configured : Firmware does not initialize + any of the generic timer CPU registers, which contain their + architecturally-defined reset values. Only supported for 32-bit + systems which follow the ARMv7 architected reset values. + + Example: timer { diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index c554ed3d44fb..556c8665fdbf 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -92,3 +92,68 @@ Required nodes: - core-module: the root node to the Versatile platforms must have a core-module with regs and the compatible strings "arm,core-module-versatile", "syscon" + +ARM RealView Boards +------------------- +The RealView boards cover tailored evaluation boards that are used to explore +the ARM11 and Cortex A-8 and Cortex A-9 processors. + +Required properties (in root node): + /* RealView Emulation Baseboard */ + compatible = "arm,realview-eb"; + /* RealView Platform Baseboard for ARM1176JZF-S */ + compatible = "arm,realview-pb1176"; + /* RealView Platform Baseboard for ARM11 MPCore */ + compatible = "arm,realview-pb11mp"; + /* RealView Platform Baseboard for Cortex A-8 */ + compatible = "arm,realview-pba8"; + /* RealView Platform Baseboard Explore for Cortex A-9 */ + compatible = "arm,realview-pbx"; + +Required nodes: + +- soc: some node of the RealView platforms must be the SoC + node that contain the SoC-specific devices, withe the compatible + string set to one of these tuples: + "arm,realview-eb-soc", "simple-bus" + "arm,realview-pb1176-soc", "simple-bus" + "arm,realview-pb11mp-soc", "simple-bus" + "arm,realview-pba8-soc", "simple-bus" + "arm,realview-pbx-soc", "simple-bus" + +- syscon: some subnode of the RealView SoC node must be a + system controller node pointing to the control registers, + with the compatible string set to one of these tuples: + "arm,realview-eb-syscon", "syscon" + "arm,realview-pb1176-syscon", "syscon" + "arm,realview-pb11mp-syscon", "syscon" + "arm,realview-pba8-syscon", "syscon" + "arm,realview-pbx-syscon", "syscon" + + Required properties for the system controller: + - regs: the location and size of the system controller registers, + one range of 0x1000 bytes. + +Example: + +/dts-v1/; +#include <dt-bindings/interrupt-controller/irq.h> +#include "skeleton.dtsi" + +/ { + model = "ARM RealView PB1176 with device tree"; + compatible = "arm,realview-pb1176"; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "arm,realview-pb1176-soc", "simple-bus"; + ranges; + + syscon: syscon@10000000 { + compatible = "arm,realview-syscon", "syscon"; + reg = <0x10000000 0x1000>; + }; + + }; +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 16f60b41c147..562cda9d86d9 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -1,6 +1,43 @@ Atmel AT91 device tree bindings. ================================ +Boards with a SoC of the Atmel AT91 or SMART family shall have the following +properties: + +Required root node properties: +compatible: must be one of: + * "atmel,at91rm9200" + + * "atmel,at91sam9" for SoCs using an ARM926EJ-S core, shall be extended with + the specific SoC family or compatible: + o "atmel,at91sam9260" + o "atmel,at91sam9261" + o "atmel,at91sam9263" + o "atmel,at91sam9x5" for the 5 series, shall be extended with the specific + SoC compatible: + - "atmel,at91sam9g15" + - "atmel,at91sam9g25" + - "atmel,at91sam9g35" + - "atmel,at91sam9x25" + - "atmel,at91sam9x35" + o "atmel,at91sam9g20" + o "atmel,at91sam9g45" + o "atmel,at91sam9n12" + o "atmel,at91sam9rl" + * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific + SoC family: + o "atmel,sama5d3" shall be extended with the specific SoC compatible: + - "atmel,sama5d31" + - "atmel,sama5d33" + - "atmel,sama5d34" + - "atmel,sama5d35" + - "atmel,sama5d36" + o "atmel,sama5d4" shall be extended with the specific SoC compatible: + - "atmel,sama5d41" + - "atmel,sama5d42" + - "atmel,sama5d43" + - "atmel,sama5d44" + PIT Timer required properties: - compatible: Should be "atmel,at91sam9260-pit" - reg: Should contain registers location and length @@ -61,8 +98,8 @@ RAMC SDRAM/DDR Controller required properties: - compatible: Should be "atmel,at91rm9200-sdramc", "atmel,at91sam9260-sdramc", "atmel,at91sam9g45-ddramc", + "atmel,sama5d3-ddramc", - reg: Should contain registers location and length - For at91sam9263 and at91sam9g45 you must specify 2 entries. Examples: @@ -71,12 +108,6 @@ Examples: reg = <0xffffe800 0x200>; }; - ramc0: ramc@ffffe400 { - compatible = "atmel,at91sam9g45-ddramc"; - reg = <0xffffe400 0x200 - 0xffffe600 0x200>; - }; - SHDWC Shutdown Controller required properties: diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt new file mode 100644 index 000000000000..bd49987a8812 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt @@ -0,0 +1,9 @@ +Broadcom BCM63138 DSL System-on-a-Chip device tree bindings +----------------------------------------------------------- + +Boards compatible with the BCM63138 DSL System-on-a-Chip should have the +following properties: + +Required root node property: + +compatible: should be "brcm,bcm63138" diff --git a/Documentation/devicetree/bindings/arm/bcm/cygnus.txt b/Documentation/devicetree/bindings/arm/bcm/cygnus.txt new file mode 100644 index 000000000000..4c77169bb534 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/cygnus.txt @@ -0,0 +1,31 @@ +Broadcom Cygnus device tree bindings +------------------------------------ + + +Boards with Cygnus SoCs shall have the following properties: + +Required root node property: + +BCM11300 +compatible = "brcm,bcm11300", "brcm,cygnus"; + +BCM11320 +compatible = "brcm,bcm11320", "brcm,cygnus"; + +BCM11350 +compatible = "brcm,bcm11350", "brcm,cygnus"; + +BCM11360 +compatible = "brcm,bcm11360", "brcm,cygnus"; + +BCM58300 +compatible = "brcm,bcm58300", "brcm,cygnus"; + +BCM58302 +compatible = "brcm,bcm58302", "brcm,cygnus"; + +BCM58303 +compatible = "brcm,bcm58303", "brcm,cygnus"; + +BCM58305 +compatible = "brcm,bcm58305", "brcm,cygnus"; diff --git a/Documentation/devicetree/bindings/arm/cavium-thunder.txt b/Documentation/devicetree/bindings/arm/cavium-thunder.txt new file mode 100644 index 000000000000..6f63a5866902 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cavium-thunder.txt @@ -0,0 +1,10 @@ +Cavium Thunder platform device tree bindings +-------------------------------------------- + +Boards with Cavium's Thunder SoC shall have following properties. + +Root Node +--------- +Required root node properties: + + - compatible = "cavium,thunder-88xx"; diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt new file mode 100644 index 000000000000..d790f49066f3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -0,0 +1,204 @@ +* CoreSight Components: + +CoreSight components are compliant with the ARM CoreSight architecture +specification and can be connected in various topologies to suit a particular +SoCs tracing needs. These trace components can generally be classified as +sinks, links and sources. Trace data produced by one or more sources flows +through the intermediate links connecting the source to the currently selected +sink. Each CoreSight component device should use these properties to describe +its hardware characteristcs. + +* Required properties for all components *except* non-configurable replicators: + + * compatible: These have to be supplemented with "arm,primecell" as + drivers are using the AMBA bus interface. Possible values include: + - "arm,coresight-etb10", "arm,primecell"; + - "arm,coresight-tpiu", "arm,primecell"; + - "arm,coresight-tmc", "arm,primecell"; + - "arm,coresight-funnel", "arm,primecell"; + - "arm,coresight-etm3x", "arm,primecell"; + + * reg: physical base address and length of the register + set(s) of the component. + + * clocks: the clock associated to this component. + + * clock-names: the name of the clock as referenced by the code. + Since we are using the AMBA framework, the name should be + "apb_pclk". + + * port or ports: The representation of the component's port + layout using the generic DT graph presentation found in + "bindings/graph.txt". + +* Required properties for devices that don't show up on the AMBA bus, such as + non-configurable replicators: + + * compatible: Currently supported value is (note the absence of the + AMBA markee): + - "arm,coresight-replicator" + + * id: a unique number that will identify this replicator. + + * port or ports: same as above. + +* Optional properties for ETM/PTMs: + + * arm,cp14: must be present if the system accesses ETM/PTM management + registers via co-processor 14. + + * cpu: the cpu phandle this ETM/PTM is affined to. When omitted the + source is considered to belong to CPU0. + +* Optional property for TMC: + + * arm,buffer-size: size of contiguous buffer space for TMC ETR + (embedded trace router) + + +Example: + +1. Sinks + etb@20010000 { + compatible = "arm,coresight-etb10", "arm,primecell"; + reg = <0 0x20010000 0 0x1000>; + + coresight-default-sink; + clocks = <&oscclk6a>; + clock-names = "apb_pclk"; + port { + etb_in_port: endpoint@0 { + slave-mode; + remote-endpoint = <&replicator_out_port0>; + }; + }; + }; + + tpiu@20030000 { + compatible = "arm,coresight-tpiu", "arm,primecell"; + reg = <0 0x20030000 0 0x1000>; + + clocks = <&oscclk6a>; + clock-names = "apb_pclk"; + port { + tpiu_in_port: endpoint@0 { + slave-mode; + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + +2. Links + replicator { + /* non-configurable replicators don't show up on the + * AMBA bus. As such no need to add "arm,primecell". + */ + compatible = "arm,coresight-replicator"; + /* this will show up in debugfs as "0.replicator" */ + id = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* replicator output ports */ + port@0 { + reg = <0>; + replicator_out_port0: endpoint { + remote-endpoint = <&etb_in_port>; + }; + }; + + port@1 { + reg = <1>; + replicator_out_port1: endpoint { + remote-endpoint = <&tpiu_in_port>; + }; + }; + + /* replicator input port */ + port@2 { + reg = <0>; + replicator_in_port0: endpoint { + slave-mode; + remote-endpoint = <&funnel_out_port0>; + }; + }; + }; + }; + + funnel@20040000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x20040000 0 0x1000>; + + clocks = <&oscclk6a>; + clock-names = "apb_pclk"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* funnel output port */ + port@0 { + reg = <0>; + funnel_out_port0: endpoint { + remote-endpoint = + <&replicator_in_port0>; + }; + }; + + /* funnel input ports */ + port@1 { + reg = <0>; + funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&ptm0_out_port>; + }; + }; + + port@2 { + reg = <1>; + funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&ptm1_out_port>; + }; + }; + + port@3 { + reg = <2>; + funnel_in_port2: endpoint { + slave-mode; + remote-endpoint = <&etm0_out_port>; + }; + }; + + }; + }; + +3. Sources + ptm@2201c000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0 0x2201c000 0 0x1000>; + + cpu = <&cpu0>; + clocks = <&oscclk6a>; + clock-names = "apb_pclk"; + port { + ptm0_out_port: endpoint { + remote-endpoint = <&funnel_in_port0>; + }; + }; + }; + + ptm@2201d000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0 0x2201d000 0 0x1000>; + + cpu = <&cpu1>; + clocks = <&oscclk6a>; + clock-names = "apb_pclk"; + port { + ptm1_out_port: endpoint { + remote-endpoint = <&funnel_in_port1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 298e2f6b33c6..b2aacbe16ed9 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -166,6 +166,7 @@ nodes to be present and contain the properties described below. "arm,cortex-r5" "arm,cortex-r7" "brcm,brahma-b15" + "cavium,thunder" "faraday,fa526" "intel,sa110" "intel,sa1100" @@ -219,6 +220,21 @@ nodes to be present and contain the properties described below. Value type: <phandle> Definition: Specifies the ACC[2] node associated with this CPU. + - cpu-idle-states + Usage: Optional + Value type: <prop-encoded-array> + Definition: + # List of phandles to idle state nodes supported + by this cpu [3]. + + - rockchip,pmu + Usage: optional for systems that have an "enable-method" + property value of "rockchip,rk3066-smp" + While optional, it is the preferred way to get access to + the cpu-core power-domains. + Value type: <phandle> + Definition: Specifies the syscon node controlling the cpu core + power domains. Example 1 (dual-cluster big.LITTLE system 32-bit): @@ -415,3 +431,5 @@ cpus { -- [1] arm/msm/qcom,saw2.txt [2] arm/msm/qcom,kpss-acc.txt +[3] ARM Linux kernel documentation - idle states bindings + Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 8b4f7b7fe88b..abde1ea8a119 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -8,6 +8,8 @@ Required Properties: * samsung,exynos4210-pd - for exynos4210 type power domain. - reg: physical base address of the controller and length of memory mapped region. +- #power-domain-cells: number of cells in power domain specifier; + must be 0. Optional Properties: - clocks: List of clock handles. The parent clocks of the input clocks to the @@ -29,6 +31,7 @@ Example: lcd0: power-domain-lcd0 { compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; + #power-domain-cells = <0>; }; mfc_pd: power-domain@10044060 { @@ -37,12 +40,8 @@ Example: clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, <&clock CLK_MOUT_USER_ACLK333>; clock-names = "oscclk", "pclk0", "clk0"; + #power-domain-cells = <0>; }; -Example of the node using power domain: - - node { - /* ... */ - samsung,power-domain = <&lcd0>; - /* ... */ - }; +See Documentation/devicetree/bindings/power/power_domain.txt for description +of consumer-side bindings. diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index e935d7d4ac43..4e8b7df7fc62 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -74,3 +74,41 @@ Required root node properties: i.MX6q generic board Required root node properties: - compatible = "fsl,imx6q"; + + +Freescale LS1021A Platform Device Tree Bindings +------------------------------------------------ + +Required root node compatible properties: + - compatible = "fsl,ls1021a"; + +Freescale LS1021A SoC-specific Device Tree Bindings +------------------------------------------- + +Freescale SCFG + SCFG is the supplemental configuration unit, that provides SoC specific +configuration and status registers for the chip. Such as getting PEX port +status. + Required properties: + - compatible: should be "fsl,ls1021a-scfg" + - reg: should contain base address and length of SCFG memory-mapped registers + +Example: + scfg: scfg@1570000 { + compatible = "fsl,ls1021a-scfg"; + reg = <0x0 0x1570000 0x0 0x10000>; + }; + +Freescale DCFG + DCFG is the device configuration unit, that provides general purpose +configuration and status for the device. Such as setting the secondary +core start address and release the secondary core from holdoff and startup. + Required properties: + - compatible: should be "fsl,ls1021a-dcfg" + - reg : should contain base address and length of DCFG memory-mapped registers + +Example: + dcfg: dcfg@1ee0000 { + compatible = "fsl,ls1021a-dcfg"; + reg = <0x0 0x1ee0000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/arm/geniatech.txt b/Documentation/devicetree/bindings/arm/geniatech.txt new file mode 100644 index 000000000000..74ccba40b73b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/geniatech.txt @@ -0,0 +1,5 @@ +Geniatech platforms device tree bindings +------------------------------------------- + +Geniatech ATV1200 + - compatible = "geniatech,atv1200" diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt index 33cd05e6c125..ddfade40ac59 100644 --- a/Documentation/devicetree/bindings/arm/gic-v3.txt +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -49,11 +49,29 @@ Optional occupied by the redistributors. Required if more than one such region is present. +Sub-nodes: + +GICv3 has one or more Interrupt Translation Services (ITS) that are +used to route Message Signalled Interrupts (MSI) to the CPUs. + +These nodes must have the following properties: +- compatible : Should at least contain "arm,gic-v3-its". +- msi-controller : Boolean property. Identifies the node as an MSI controller +- reg: Specifies the base physical address and size of the ITS + registers. + +The main GIC node must contain the appropriate #address-cells, +#size-cells and ranges properties for the reg property of all ITS +nodes. + Examples: gic: interrupt-controller@2cf00000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; interrupt-controller; reg = <0x0 0x2f000000 0 0x10000>, // GICD <0x0 0x2f100000 0 0x200000>, // GICR @@ -61,11 +79,20 @@ Examples: <0x0 0x2c010000 0 0x2000>, // GICH <0x0 0x2c020000 0 0x2000>; // GICV interrupts = <1 9 4>; + + gic-its@2c200000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x2c200000 0 0x200000>; + }; }; gic: interrupt-controller@2c010000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; interrupt-controller; redistributor-stride = <0x0 0x40000>; // 256kB stride #redistributor-regions = <2>; @@ -76,4 +103,16 @@ Examples: <0x0 0x2c060000 0 0x2000>, // GICH <0x0 0x2c080000 0 0x2000>; // GICV interrupts = <1 9 4>; + + gic-its@2c200000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x2c200000 0 0x200000>; + }; + + gic-its@2c400000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x2c400000 0 0x200000>; + }; }; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index c7d2fa156678..8112d0c3675a 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -17,6 +17,7 @@ Main node required properties: "arm,cortex-a7-gic" "arm,arm11mp-gic" "brcm,brahma-b15-gic" + "arm,arm1176jzf-devchip-gic" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 3. @@ -96,3 +97,56 @@ Example: <0x2c006000 0x2000>; interrupts = <1 9 0xf04>; }; + + +* GICv2m extension for MSI/MSI-x support (Optional) + +Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s). +This is enabled by specifying v2m sub-node(s). + +Required properties: + +- compatible : The value here should contain "arm,gic-v2m-frame". + +- msi-controller : Identifies the node as an MSI controller. + +- reg : GICv2m MSI interface register base and size + +Optional properties: + +- arm,msi-base-spi : When the MSI_TYPER register contains an incorrect + value, this property should contain the SPI base of + the MSI frame, overriding the HW value. + +- arm,msi-num-spis : When the MSI_TYPER register contains an incorrect + value, this property should contain the number of + SPIs assigned to the frame, overriding the HW value. + +Example: + + interrupt-controller@e1101000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + interrupt-controller; + interrupts = <1 8 0xf04>; + ranges = <0 0 0 0xe1100000 0 0x100000>; + reg = <0x0 0xe1110000 0 0x01000>, + <0x0 0xe112f000 0 0x02000>, + <0x0 0xe1140000 0 0x10000>, + <0x0 0xe1160000 0 0x10000>; + v2m0: v2m@0x8000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x80000 0 0x1000>; + }; + + .... + + v2mN: v2m@0x9000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x90000 0 0x1000>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 934f00025cc4..f717c7b48603 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -5,6 +5,11 @@ Hi4511 Board Required root node properties: - compatible = "hisilicon,hi3620-hi4511"; +HiP04 D01 Board +Required root node properties: + - compatible = "hisilicon,hip04-d01"; + + Hisilicon system controller Required properties: @@ -55,3 +60,21 @@ Example: compatible = "hisilicon,pctrl"; reg = <0xfca09000 0x1000>; }; + +----------------------------------------------------------------------- +Fabric: + +Required Properties: +- compatible: "hisilicon,hip04-fabric"; +- reg: Address and size of Fabric + +----------------------------------------------------------------------- +Bootwrapper boot method (software protocol on SMP): + +Required Properties: +- compatible: "hisilicon,hip04-bootwrapper"; +- boot-method: Address and size of boot method. + [0]: bootwrapper physical address + [1]: bootwrapper size + [2]: relocation physical address + [3]: relocation size diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt new file mode 100644 index 000000000000..a8274eabae2e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -0,0 +1,699 @@ +========================================== +ARM idle states binding description +========================================== + +========================================== +1 - Introduction +========================================== + +ARM systems contain HW capable of managing power consumption dynamically, +where cores can be put in different low-power states (ranging from simple +wfi to power gating) according to OS PM policies. The CPU states representing +the range of dynamic idle states that a processor can enter at run-time, can be +specified through device tree bindings representing the parameters required +to enter/exit specific idle states on a given processor. + +According to the Server Base System Architecture document (SBSA, [3]), the +power states an ARM CPU can be put into are identified by the following list: + +- Running +- Idle_standby +- Idle_retention +- Sleep +- Off + +The power states described in the SBSA document define the basic CPU states on +top of which ARM platforms implement power management schemes that allow an OS +PM implementation to put the processor in different idle states (which include +states listed above; "off" state is not an idle state since it does not have +wake-up capabilities, hence it is not considered in this document). + +Idle state parameters (eg entry latency) are platform specific and need to be +characterized with bindings that provide the required information to OS PM +code so that it can build the required tables and use them at runtime. + +The device tree binding definition for ARM idle states is the subject of this +document. + +=========================================== +2 - idle-states definitions +=========================================== + +Idle states are characterized for a specific system through a set of +timing and energy related properties, that underline the HW behaviour +triggered upon idle states entry and exit. + +The following diagram depicts the CPU execution phases and related timing +properties required to enter and exit an idle state: + +..__[EXEC]__|__[PREP]__|__[ENTRY]__|__[IDLE]__|__[EXIT]__|__[EXEC]__.. + | | | | | + + |<------ entry ------->| + | latency | + |<- exit ->| + | latency | + |<-------- min-residency -------->| + |<------- wakeup-latency ------->| + + Diagram 1: CPU idle state execution phases + +EXEC: Normal CPU execution. + +PREP: Preparation phase before committing the hardware to idle mode + like cache flushing. This is abortable on pending wake-up + event conditions. The abort latency is assumed to be negligible + (i.e. less than the ENTRY + EXIT duration). If aborted, CPU + goes back to EXEC. This phase is optional. If not abortable, + this should be included in the ENTRY phase instead. + +ENTRY: The hardware is committed to idle mode. This period must run + to completion up to IDLE before anything else can happen. + +IDLE: This is the actual energy-saving idle period. This may last + between 0 and infinite time, until a wake-up event occurs. + +EXIT: Period during which the CPU is brought back to operational + mode (EXEC). + +entry-latency: Worst case latency required to enter the idle state. The +exit-latency may be guaranteed only after entry-latency has passed. + +min-residency: Minimum period, including preparation and entry, for a given +idle state to be worthwhile energywise. + +wakeup-latency: Maximum delay between the signaling of a wake-up event and the +CPU being able to execute normal code again. If not specified, this is assumed +to be entry-latency + exit-latency. + +These timing parameters can be used by an OS in different circumstances. + +An idle CPU requires the expected min-residency time to select the most +appropriate idle state based on the expected expiry time of the next IRQ +(ie wake-up) that causes the CPU to return to the EXEC phase. + +An operating system scheduler may need to compute the shortest wake-up delay +for CPUs in the system by detecting how long will it take to get a CPU out +of an idle state, eg: + +wakeup-delay = exit-latency + max(entry-latency - (now - entry-timestamp), 0) + +In other words, the scheduler can make its scheduling decision by selecting +(eg waking-up) the CPU with the shortest wake-up latency. +The wake-up latency must take into account the entry latency if that period +has not expired. The abortable nature of the PREP period can be ignored +if it cannot be relied upon (e.g. the PREP deadline may occur much sooner than +the worst case since it depends on the CPU operating conditions, ie caches +state). + +An OS has to reliably probe the wakeup-latency since some devices can enforce +latency constraints guarantees to work properly, so the OS has to detect the +worst case wake-up latency it can incur if a CPU is allowed to enter an +idle state, and possibly to prevent that to guarantee reliable device +functioning. + +The min-residency time parameter deserves further explanation since it is +expressed in time units but must factor in energy consumption coefficients. + +The energy consumption of a cpu when it enters a power state can be roughly +characterised by the following graph: + + | + | + | + e | + n | /--- + e | /------ + r | /------ + g | /----- + y | /------ + | ---- + | /| + | / | + | / | + | / | + | / | + | / | + |/ | + -----|-------+---------------------------------- + 0| 1 time(ms) + + Graph 1: Energy vs time example + +The graph is split in two parts delimited by time 1ms on the X-axis. +The graph curve with X-axis values = { x | 0 < x < 1ms } has a steep slope +and denotes the energy costs incurred whilst entering and leaving the idle +state. +The graph curve in the area delimited by X-axis values = {x | x > 1ms } has +shallower slope and essentially represents the energy consumption of the idle +state. + +min-residency is defined for a given idle state as the minimum expected +residency time for a state (inclusive of preparation and entry) after +which choosing that state become the most energy efficient option. A good +way to visualise this, is by taking the same graph above and comparing some +states energy consumptions plots. + +For sake of simplicity, let's consider a system with two idle states IDLE1, +and IDLE2: + + | + | + | + | /-- IDLE1 + e | /--- + n | /---- + e | /--- + r | /-----/--------- IDLE2 + g | /-------/--------- + y | ------------ /---| + | / /---- | + | / /--- | + | / /---- | + | / /--- | + | --- | + | / | + | / | + |/ | time + ---/----------------------------+------------------------ + |IDLE1-energy < IDLE2-energy | IDLE2-energy < IDLE1-energy + | + IDLE2-min-residency + + Graph 2: idle states min-residency example + +In graph 2 above, that takes into account idle states entry/exit energy +costs, it is clear that if the idle state residency time (ie time till next +wake-up IRQ) is less than IDLE2-min-residency, IDLE1 is the better idle state +choice energywise. + +This is mainly down to the fact that IDLE1 entry/exit energy costs are lower +than IDLE2. + +However, the lower power consumption (ie shallower energy curve slope) of idle +state IDLE2 implies that after a suitable time, IDLE2 becomes more energy +efficient. + +The time at which IDLE2 becomes more energy efficient than IDLE1 (and other +shallower states in a system with multiple idle states) is defined +IDLE2-min-residency and corresponds to the time when energy consumption of +IDLE1 and IDLE2 states breaks even. + +The definitions provided in this section underpin the idle states +properties specification that is the subject of the following sections. + +=========================================== +3 - idle-states node +=========================================== + +ARM processor idle states are defined within the idle-states node, which is +a direct child of the cpus node [1] and provides a container where the +processor idle states, defined as device tree nodes, are listed. + +- idle-states node + + Usage: Optional - On ARM systems, it is a container of processor idle + states nodes. If the system does not provide CPU + power management capabilities or the processor just + supports idle_standby an idle-states node is not + required. + + Description: idle-states node is a container node, where its + subnodes describe the CPU idle states. + + Node name must be "idle-states". + + The idle-states node's parent node must be the cpus node. + + The idle-states node's child nodes can be: + + - one or more state nodes + + Any other configuration is considered invalid. + + An idle-states node defines the following properties: + + - entry-method + Value type: <stringlist> + Usage and definition depend on ARM architecture version. + # On ARM v8 64-bit this property is required and must + be one of: + - "psci" (see bindings in [2]) + # On ARM 32-bit systems this property is optional + +The nodes describing the idle states (state) can only be defined within the +idle-states node, any other configuration is considered invalid and therefore +must be ignored. + +=========================================== +4 - state node +=========================================== + +A state node represents an idle state description and must be defined as +follows: + +- state node + + Description: must be child of the idle-states node + + The state node name shall follow standard device tree naming + rules ([5], 2.2.1 "Node names"), in particular state nodes which + are siblings within a single common parent must be given a unique name. + + The idle state entered by executing the wfi instruction (idle_standby + SBSA,[3][4]) is considered standard on all ARM platforms and therefore + must not be listed. + + With the definitions provided above, the following list represents + the valid properties for a state node: + + - compatible + Usage: Required + Value type: <stringlist> + Definition: Must be "arm,idle-state". + + - local-timer-stop + Usage: See definition + Value type: <none> + Definition: if present the CPU local timer control logic is + lost on state entry, otherwise it is retained. + + - entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + + - exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + + - min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds, inclusive of preparation and + entry, for this idle state to be considered + worthwhile energy wise (refer to section 2 of + this document for a complete description). + + - wakeup-latency-us: + Usage: Optional + Value type: <prop-encoded-array> + Definition: u32 value representing maximum delay between the + signaling of a wake-up event and the CPU being + able to execute normal code again. If omitted, + this is assumed to be equal to: + + entry-latency-us + exit-latency-us + + It is important to supply this value on systems + where the duration of PREP phase (see diagram 1, + section 2) is non-neglibigle. + In such systems entry-latency-us + exit-latency-us + will exceed wakeup-latency-us by this duration. + + - status: + Usage: Optional + Value type: <string> + Definition: A standard device tree property [5] that indicates + the operational status of an idle-state. + If present, it shall be: + "okay": to indicate that the idle state is + operational. + "disabled": to indicate that the idle state has + been disabled in firmware so it is not + operational. + If the property is not present the idle-state must + be considered operational. + + - idle-state-name: + Usage: Optional + Value type: <string> + Definition: A string used as a descriptive name for the idle + state. + + In addition to the properties listed above, a state node may require + additional properties specifics to the entry-method defined in the + idle-states node, please refer to the entry-method bindings + documentation for properties definitions. + +=========================================== +4 - Examples +=========================================== + +Example 1 (ARM 64-bit, 16-cpu system, PSCI enable-method): + +cpus { + #size-cells = <0>; + #address-cells = <2>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x1>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU4: cpu@10000 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU5: cpu@10001 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU6: cpu@10100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU7: cpu@10101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU8: cpu@100000000 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU9: cpu@100000001 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x1>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU10: cpu@100000100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU11: cpu@100000101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU12: cpu@100010000 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU13: cpu@100010001 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU14: cpu@100010100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU15: cpu@100010101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + idle-states { + entry-method = "arm,psci"; + + CPU_RETENTION_0_0: cpu-retention-0-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <20>; + exit-latency-us = <40>; + min-residency-us = <80>; + }; + + CLUSTER_RETENTION_0: cluster-retention-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <50>; + exit-latency-us = <100>; + min-residency-us = <250>; + wakeup-latency-us = <130>; + }; + + CPU_SLEEP_0_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <250>; + exit-latency-us = <500>; + min-residency-us = <950>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <600>; + exit-latency-us = <1100>; + min-residency-us = <2700>; + wakeup-latency-us = <1500>; + }; + + CPU_RETENTION_1_0: cpu-retention-1-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <20>; + exit-latency-us = <40>; + min-residency-us = <90>; + }; + + CLUSTER_RETENTION_1: cluster-retention-1 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <50>; + exit-latency-us = <100>; + min-residency-us = <270>; + wakeup-latency-us = <100>; + }; + + CPU_SLEEP_1_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <70>; + exit-latency-us = <100>; + min-residency-us = <300>; + wakeup-latency-us = <150>; + }; + + CLUSTER_SLEEP_1: cluster-sleep-1 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <500>; + exit-latency-us = <1200>; + min-residency-us = <3500>; + wakeup-latency-us = <1300>; + }; + }; + +}; + +Example 2 (ARM 32-bit, 8-cpu system, two clusters): + +cpus { + #size-cells = <0>; + #address-cells = <1>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x2>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x3>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + idle-states { + CPU_SLEEP_0_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <200>; + exit-latency-us = <100>; + min-residency-us = <400>; + wakeup-latency-us = <250>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <500>; + exit-latency-us = <1500>; + min-residency-us = <2500>; + wakeup-latency-us = <1700>; + }; + + CPU_SLEEP_1_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <300>; + exit-latency-us = <500>; + min-residency-us = <900>; + wakeup-latency-us = <600>; + }; + + CLUSTER_SLEEP_1: cluster-sleep-1 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <800>; + exit-latency-us = <2000>; + min-residency-us = <6500>; + wakeup-latency-us = <2300>; + }; + }; + +}; + +=========================================== +5 - References +=========================================== + +[1] ARM Linux Kernel documentation - CPUs bindings + Documentation/devicetree/bindings/arm/cpus.txt + +[2] ARM Linux Kernel documentation - PSCI bindings + Documentation/devicetree/bindings/arm/psci.txt + +[3] ARM Server Base System Architecture (SBSA) + http://infocenter.arm.com/help/index.jsp + +[4] ARM Architecture Reference Manuals + http://infocenter.arm.com/help/index.jsp + +[5] ePAPR standard + https://www.power.org/documentation/epapr-version-1-1/ diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index af527ee111c2..292ef7ca3058 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -2,6 +2,10 @@ ARM cores often have a separate level 2 cache controller. There are various implementations of the L2 cache controller with compatible programming models. +Some of the properties that are just prefixed "cache-*" are taken from section +3.7.3 of the ePAPR v1.1 specification which can be found at: +https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf + The ARM L2 cache representation in the device tree should be done as follows: Required properties: @@ -44,6 +48,12 @@ Optional properties: I/O coherent mode. Valid only when the arm,pl310-cache compatible string is used. - interrupts : 1 combined interrupt. +- cache-size : specifies the size in bytes of the cache +- cache-sets : specifies the number of associativity sets of the cache +- cache-block-size : specifies the size in bytes of a cache block +- cache-line-size : specifies the size in bytes of a line in the cache, + if this is not specified, the line size is assumed to be equal to the + cache block size - cache-id-part: cache id part number to be used if it is not present on hardware - wt-override: If present then L2 is forced to Write through mode diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt index 904de5781f44..a99eb9eb14c0 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt @@ -106,11 +106,21 @@ Required subnode-properties: - groups: a list of strings describing the group names. - function: a string describing the function used to mux the groups. +* Reset controller binding + +A reset controller is part of the chip control registers set. The chip control +node also provides the reset. The register set is not at the same offset between +Berlin SoCs. + +Required property: +- #reset-cells: must be set to 2 + Example: chip: chip-control@ea0000 { compatible = "marvell,berlin2-chip-ctrl"; #clock-cells = <1>; + #reset-cells = <2>; reg = <0xea0000 0x400>; clocks = <&refclk>, <&externaldev 0>; clock-names = "refclk", "video_ext0"; diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index d6ac71f37314..3be40139cfbb 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -1,8 +1,27 @@ -Mediatek MT6589 Platforms Device Tree Bindings +MediaTek mt65xx & mt81xx Platforms Device Tree Bindings -Boards with a SoC of the Mediatek MT6589 shall have the following property: +Boards with a MediaTek mt65xx/mt81xx SoC shall have the following property: Required root node property: -compatible: must contain "mediatek,mt6589" +compatible: Must contain one of + "mediatek,mt6589" + "mediatek,mt6592" + "mediatek,mt8127" + "mediatek,mt8135" + +Supported boards: + +- bq Aquaris5 smart phone: + Required root node properties: + - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589"; +- Evaluation board for MT6592: + Required root node properties: + - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; +- MTK mt8127 tablet moose EVB: + Required root node properties: + - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; +- MTK mt8135 tablet EVB: + Required root node properties: + - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt new file mode 100644 index 000000000000..d680b07ec6e8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt @@ -0,0 +1,28 @@ +Mediatek 65xx/81xx sysirq + +Mediatek SOCs sysirq support controllable irq inverter for each GIC SPI +interrupt. + +Required properties: +- compatible: should be one of: + "mediatek,mt8135-sysirq" + "mediatek,mt8127-sysirq" + "mediatek,mt6589-sysirq" + "mediatek,mt6582-sysirq" + "mediatek,mt6577-sysirq" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Use the same format as specified by GIC in + Documentation/devicetree/bindings/arm/gic.txt +- interrupt-parent: phandle of irq parent for sysirq. The parent must + use the same interrupt-cells format as GIC. +- reg: Physical base address of the intpol registers and length of memory + mapped region. + +Example: + sysirq: interrupt-controller@10200100 { + compatible = "mediatek,mt6589-sysirq", "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200100 0 0x1c>; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt index 83f405bde138..763695db2bd9 100644 --- a/Documentation/devicetree/bindings/arm/omap/mpu.txt +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -10,6 +10,9 @@ Required properties: Should be "ti,omap5-mpu" for OMAP5 - ti,hwmods: "mpu" +Optional properties: +- sram: Phandle to the ocmcram node + Examples: - For an OMAP5 SMP system: diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 0edc90305dfe..4f6a82cef1d1 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -85,6 +85,18 @@ SoCs: - DRA722 compatible = "ti,dra722", "ti,dra72", "ti,dra7" +- AM5728 + compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM5726 + compatible = "ti,am5726", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM5718 + compatible = "ti,am5718", "ti,dra722", "ti,dra72", "ti,dra7" + +- AM5716 + compatible = "ti,am5716", "ti,dra722", "ti,dra72", "ti,dra7" + - AM4372 compatible = "ti,am4372", "ti,am43" @@ -120,6 +132,9 @@ Boards: - AM335X Bone : Low cost community board compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" +- AM335X OrionLXm : Substation Automation Platform + compatible = "novatech,am335x-lxm", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index b4a58f39223c..5aa40ede0e99 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -50,6 +50,16 @@ Main node optional properties: - migrate : Function ID for MIGRATE operation +Device tree nodes that require usage of PSCI CPU_SUSPEND function (ie idle +state nodes, as per bindings in [1]) must specify the following properties: + +- arm,psci-suspend-param + Usage: Required for state nodes[1] if the corresponding + idle-states node entry-method property is set + to "psci". + Value type: <u32> + Definition: power_state parameter to pass to the PSCI + suspend call. Example: @@ -64,7 +74,6 @@ Case 1: PSCI v0.1 only. migrate = <0x95c10003>; }; - Case 2: PSCI v0.2 only psci { @@ -88,3 +97,6 @@ Case 3: PSCI v0.2 and PSCI v0.1. ... }; + +[1] Kernel documentation - ARM idle states bindings + Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 857f12636eb2..eaa3d1a0eb05 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -1,6 +1,10 @@ Rockchip platforms device tree bindings --------------------------------------- +- MarsBoard RK3066 board: + Required root node properties: + - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a"; + - bq Curie 2 tablet: Required root node properties: - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt index 2168ed31e1b0..43589d2466a7 100644 --- a/Documentation/devicetree/bindings/arm/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung-boards.txt @@ -1,11 +1,20 @@ -* Samsung's Exynos4210 based SMDKV310 evaluation board - -SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC. +* Samsung's Exynos SoC based boards Required root node properties: - compatible = should be one or more of the following. - (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. - (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. + - "samsung,monk" - for Exynos3250-based Samsung Simband board. + - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. + - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. + - "samsung,trats" - for Exynos4210-based Tizen Reference board. + - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,trats2" - for Exynos4412-based Tizen Reference board. + - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. + - "samsung,xyref5260" - for Exynos5260-based Samsung board. + - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. + - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,sd5v1" - for Exynos5440-based Samsung board. + - "samsung,ssdk5440" - for Exynos5440-based Samsung board. Optional: - firmware node, specifying presence and type of secure firmware: diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index adc61b095bd1..f46ca9a316a2 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -11,13 +11,27 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for exynos4412/5250 and s5pv210 controllers. Must be "samsung,exynos-adc-v2" for future controllers. Must be "samsung,exynos3250-adc" for controllers compatible with ADC of Exynos3250. -- reg: Contains ADC register address range (base address and - length) and the address of the phy enable register. + Must be "samsung,exynos7-adc" for + the ADC in Exynos7 and compatibles + Must be "samsung,s3c2410-adc" for + the ADC in s3c2410 and compatibles + Must be "samsung,s3c2416-adc" for + the ADC in s3c2416 and compatibles + Must be "samsung,s3c2440-adc" for + the ADC in s3c2440 and compatibles + Must be "samsung,s3c2443-adc" for + the ADC in s3c2443 and compatibles + Must be "samsung,s3c6410-adc" for + the ADC in s3c6410 and compatibles +- reg: List of ADC register address range + - The base address and range of ADC register + - The base address and range of ADC_PHY register (every + SoC except for s3c24xx/s3c64xx ADC) - interrupts: Contains the interrupt information for the timer. The format is being dependent on which interrupt controller the Samsung device uses. @@ -31,13 +45,16 @@ Required properties: compatible ADC block) - vdd-supply VDD input supply. +- samsung,syscon-phandle Contains the PMU system controller node + (To access the ADC_PHY register on Exynos5250/5420/5800/3250) + Note: child nodes can be added for auto probing from device tree. Example: adding device info in dtsi file adc: adc@12D10000 { compatible = "samsung,exynos-adc-v1"; - reg = <0x12D10000 0x100>, <0x10040718 0x4>; + reg = <0x12D10000 0x100>; interrupts = <0 106 0>; #io-channel-cells = <1>; io-channel-ranges; @@ -46,13 +63,14 @@ adc: adc@12D10000 { clock-names = "adc"; vdd-supply = <&buck5_reg>; + samsung,syscon-phandle = <&pmu_system_controller>; }; Example: adding device info in dtsi file for Exynos3250 with additional sclk adc: adc@126C0000 { compatible = "samsung,exynos3250-adc", "samsung,exynos-adc-v2; - reg = <0x126C0000 0x100>, <0x10020718 0x4>; + reg = <0x126C0000 0x100>; interrupts = <0 137 0>; #io-channel-cells = <1>; io-channel-ranges; @@ -61,6 +79,7 @@ adc: adc@126C0000 { clock-names = "adc", "sclk"; vdd-supply = <&buck5_reg>; + samsung,syscon-phandle = <&pmu_system_controller>; }; Example: Adding child nodes in dts file diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt new file mode 100644 index 000000000000..51147cb5c036 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -0,0 +1,71 @@ +Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings +-------------------------------------------------------------------- + +SoCs: + + - Emma Mobile EV2 + compatible = "renesas,emev2" + - RZ/A1H (R7S72100) + compatible = "renesas,r7s72100" + - SH-Mobile AP4 (R8A73720/SH7372) + compatible = "renesas,sh7372" + - SH-Mobile AG5 (R8A73A00/SH73A0) + compatible = "renesas,sh73a0" + - R-Mobile APE6 (R8A73A40) + compatible = "renesas,r8a73a4" + - R-Mobile A1 (R8A77400) + compatible = "renesas,r8a7740" + - R-Car M1A (R8A77781) + compatible = "renesas,r8a7778" + - R-Car H1 (R8A77790) + compatible = "renesas,r8a7779" + - R-Car H2 (R8A77900) + compatible = "renesas,r8a7790" + - R-Car M2-W (R8A77910) + compatible = "renesas,r8a7791" + - R-Car V2H (R8A77920) + compatible = "renesas,r8a7792" + - R-Car M2-N (R8A77930) + compatible = "renesas,r8a7793" + - R-Car E2 (R8A77940) + compatible = "renesas,r8a7794" + + +Boards: + + - Alt + compatible = "renesas,alt", "renesas,r8a7794" + - APE6-EVM + compatible = "renesas,ape6evm", "renesas,r8a73a4" + - APE6-EVM - Reference Device Tree Implementation + compatible = "renesas,ape6evm-reference", "renesas,r8a73a4" + - Atmark Techno Armadillo-800 EVA + compatible = "renesas,armadillo800eva" + - BOCK-W + compatible = "renesas,bockw", "renesas,r8a7778" + - BOCK-W - Reference Device Tree Implementation + compatible = "renesas,bockw-reference", "renesas,r8a7778" + - Genmai (RTK772100BC00000BR) + compatible = "renesas,genmai", "renesas,r7s72100" + - Gose + compatible = "renesas,gose", "renesas,r8a7793" + - Henninger + compatible = "renesas,henninger", "renesas,r8a7791" + - Koelsch (RTP0RC7791SEB00010S) + compatible = "renesas,koelsch", "renesas,r8a7791" + - Kyoto Microcomputer Co. KZM-A9-Dual + compatible = "renesas,kzm9d", "renesas,emev2" + - Kyoto Microcomputer Co. KZM-A9-GT + compatible = "renesas,kzm9g", "renesas,sh73a0" + - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation + compatible = "renesas,kzm9g-reference", "renesas,sh73a0" + - Lager (RTP0RC7790SEB00010S) + compatible = "renesas,lager", "renesas,r8a7790" + - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd) + compatible = "renesas,mackerel" + - Marzen + compatible = "renesas,marzen", "renesas,r8a7779" + +Note: Reference Device Tree Implementations are temporary implementations + to ease the migration from platform devices to Device Tree, and are + intended to be removed in the future. diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt index 6256ec31666d..2fdff5a806cf 100644 --- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt @@ -10,6 +10,12 @@ Required root node property: src Boards with the Nomadik SoC include: +Nomadik NHK-15 board manufactured by ST Microelectronics: + +Required root node property: + +compatible="st,nomadik-nhk-15"; + S8815 "MiniKit" manufactured by Calao Systems: Required root node property: diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt new file mode 100644 index 000000000000..42941fdefb11 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -0,0 +1,12 @@ +Allwinner sunXi Platforms Device Tree Bindings + +Each device tree must specify which Allwinner SoC it uses, +using one of the following compatible strings: + + allwinner,sun4i-a10 + allwinner,sun5i-a10s + allwinner,sun5i-a13 + allwinner,sun6i-a31 + allwinner,sun7i-a20 + allwinner,sun8i-a23 + allwinner,sun9i-a80 diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt new file mode 100644 index 000000000000..ccf0adddc820 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt @@ -0,0 +1,12 @@ +NVIDIA Tegra Flow Controller + +Required properties: +- compatible: Should be "nvidia,tegra<chip>-flowctrl" +- reg: Should contain one register range (address and length) + +Example: + + flow-controller@60007000 { + compatible = "nvidia,tegra20-flowctrl"; + reg = <0x60007000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/ux500/power_domain.txt b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt new file mode 100644 index 000000000000..5679d1742d3e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt @@ -0,0 +1,35 @@ +* ST-Ericsson UX500 PM Domains + +UX500 supports multiple PM domains which are used to gate power to one or +more peripherals on the SOC. + +The implementation of PM domains for UX500 are based upon the generic PM domain +and use the corresponding DT bindings. + +==PM domain providers== + +Required properties: + - compatible: Must be "stericsson,ux500-pm-domains". + - #power-domain-cells : Number of cells in a power domain specifier, must be 1. + +Example: + pm_domains: pm_domains0 { + compatible = "stericsson,ux500-pm-domains"; + #power-domain-cells = <1>; + }; + +==PM domain consumers== + +Required properties: + - power-domains: A phandle and PM domain specifier. Below are the list of + valid specifiers: + + Index Specifier + ----- --------- + 0 DOMAIN_VAPE + +Example: + sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + power-domains = <&pm_domains DOMAIN_VAPE> + }; diff --git a/Documentation/devicetree/bindings/ata/marvell.txt b/Documentation/devicetree/bindings/ata/marvell.txt index 1c8351604d38..b460edd12766 100644 --- a/Documentation/devicetree/bindings/ata/marvell.txt +++ b/Documentation/devicetree/bindings/ata/marvell.txt @@ -6,11 +6,17 @@ Required Properties: - interrupts : Interrupt controller is using - nr-ports : Number of SATA ports in use. +Optional Properties: +- phys : List of phandles to sata phys +- phy-names : Should be "0", "1", etc, one number per phandle + Example: sata@80000 { compatible = "marvell,orion-sata"; reg = <0x80000 0x5000>; interrupts = <21>; + phys = <&sata_phy0>, <&sata_phy1>; + phy-names = "0", "1"; nr-ports = <2>; } diff --git a/Documentation/devicetree/bindings/ata/qcom-sata.txt b/Documentation/devicetree/bindings/ata/qcom-sata.txt new file mode 100644 index 000000000000..094de91cd9fd --- /dev/null +++ b/Documentation/devicetree/bindings/ata/qcom-sata.txt @@ -0,0 +1,48 @@ +* Qualcomm AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, must contain "generic-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- phys : Must contain exactly one entry as specified + in phy-bindings.txt +- phy-names : Must be "sata-phy" + +Required properties for "qcom,ipq806x-ahci" compatible: +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be: + "slave_iface" - Fabric port AHB clock for SATA + "iface" - AHB clock + "core" - core clock + "rxoob" - RX out-of-band clock + "pmalive" - Power Module Alive clock +- assigned-clocks : Shall be: + SATA_RXOOB_CLK + SATA_PMALIVE_CLK +- assigned-clock-rates : Shall be: + 100Mhz (100000000) for SATA_RXOOB_CLK + 100Mhz (100000000) for SATA_PMALIVE_CLK + +Example: + sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <0 209 0x0>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_iface", "iface", "core", + "rxoob", "pmalive"; + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt index 1e6111333fa8..2493a5a31655 100644 --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt @@ -3,16 +3,21 @@ Required properties: - compatible : should contain one of the following: - "renesas,sata-r8a7779" for R-Car H1 - - "renesas,sata-r8a7790" for R-Car H2 - - "renesas,sata-r8a7791" for R-Car M2 + ("renesas,rcar-sata" is deprecated) + - "renesas,sata-r8a7790-es1" for R-Car H2 ES1 + - "renesas,sata-r8a7790" for R-Car H2 other than ES1 + - "renesas,sata-r8a7791" for R-Car M2-W + - "renesas,sata-r8a7793" for R-Car M2-N - reg : address and length of the SATA registers; - interrupts : must consist of one interrupt specifier. +- clocks : must contain a reference to the functional clock. Example: -sata: sata@fc600000 { - compatible = "renesas,sata-r8a7779"; - reg = <0xfc600000 0x2000>; +sata0: sata@ee300000 { + compatible = "renesas,sata-r8a7791"; + reg = <0 0xee300000 0 0x2000>; interrupt-parent = <&gic>; - interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7791_CLK_SATA0>; }; diff --git a/Documentation/devicetree/bindings/btmrvl.txt b/Documentation/devicetree/bindings/btmrvl.txt new file mode 100644 index 000000000000..58f964bb0a52 --- /dev/null +++ b/Documentation/devicetree/bindings/btmrvl.txt @@ -0,0 +1,29 @@ +btmrvl +------ + +Required properties: + + - compatible : must be "btmrvl,cfgdata" + +Optional properties: + + - btmrvl,cal-data : Calibration data downloaded to the device during + initialization. This is an array of 28 values(u8). + + - btmrvl,gpio-gap : gpio and gap (in msecs) combination to be + configured. + +Example: + +GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs +in below example. + +btmrvl { + compatible = "btmrvl,cfgdata"; + + btmrvl,cal-data = /bits/ 8 < + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0xf0 0x00>; + btmrvl,gpio-gap = <0x0d64>; +}; diff --git a/Documentation/devicetree/bindings/bus/bcma.txt b/Documentation/devicetree/bindings/bus/bcma.txt new file mode 100644 index 000000000000..edd44d802139 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/bcma.txt @@ -0,0 +1,53 @@ +Driver for ARM AXI Bus with Broadcom Plugins (bcma) + +Required properties: + +- compatible : brcm,bus-axi + +- reg : iomem address range of chipcommon core + +The cores on the AXI bus are automatically detected by bcma with the +memory ranges they are using and they get registered afterwards. +Automatic detection of the IRQ number is not working on +BCM47xx/BCM53xx ARM SoCs. To assign IRQ numbers to the cores, provide +them manually through device tree. Use an interrupt-map to specify the +IRQ used by the devices on the bus. The first address is just an index, +because we do not have any special register. + +The top-level axi bus may contain children representing attached cores +(devices). This is needed since some hardware details can't be auto +detected (e.g. IRQ numbers). Also some of the cores may be responsible +for extra things, e.g. ChipCommon providing access to the GPIO chip. + +Example: + + axi@18000000 { + compatible = "brcm,bus-axi"; + reg = <0x18000000 0x1000>; + ranges = <0x00000000 0x18000000 0x00100000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <1>; + interrupt-map-mask = <0x000fffff 0xffff>; + interrupt-map = + /* Ethernet Controller 0 */ + <0x00024000 0 &gic GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + + /* Ethernet Controller 1 */ + <0x00025000 0 &gic GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + + /* PCIe Controller 0 */ + <0x00012000 0 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, + <0x00012000 1 &gic GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>, + <0x00012000 2 &gic GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <0x00012000 3 &gic GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <0x00012000 4 &gic GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>, + <0x00012000 5 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + + chipcommon { + reg = <0x00000000 0x1000>; + + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt index e2d501d20c9a..1eceefb20f01 100644 --- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -2,7 +2,11 @@ Broadcom GISB bus Arbiter controller Required properties: -- compatible: should be "brcm,gisb-arb" +- compatible: + "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips + "brcm,bcm7435-gisb-arb" for newer 40nm chips + "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips + "brcm,bcm7038-gisb-arb" for 130nm chips - reg: specifies the base physical address and size of the registers - interrupt-parent: specifies the phandle to the parent interrupt controller this arbiter gets interrupt line from diff --git a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt index 5fa44f52a0b8..5e16c3ccb061 100644 --- a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt +++ b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt @@ -48,9 +48,12 @@ Required properties: - compatible: Should be set to "marvell,mbus-controller". - reg: Device's register space. - Two entries are expected (see the examples below): - the first one controls the devices decoding window and - the second one controls the SDRAM decoding window. + Two or three entries are expected (see the examples below): + the first one controls the devices decoding window, + the second one controls the SDRAM decoding window and + the third controls the MBus bridge (only with the + marvell,armada370-mbus and marvell,armadaxp-mbus + compatible strings) Example: @@ -67,7 +70,7 @@ Example: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -126,7 +129,7 @@ are skipped. mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -170,7 +173,7 @@ Using this macro, the above example would be: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* other children */ @@ -266,7 +269,7 @@ See the example below, where a more complete device tree is shown: ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; mbusc: mbus-controller@20000 { - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; interrupt-controller@20000 { diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt new file mode 100644 index 000000000000..ed838f453f7a --- /dev/null +++ b/Documentation/devicetree/bindings/chosen.txt @@ -0,0 +1,46 @@ +The chosen node +--------------- + +The chosen node does not represent a real device, but serves as a place +for passing data between firmware and the operating system, like boot +arguments. Data in the chosen node does not represent the hardware. + + +stdout-path property +-------------------- + +Device trees may specify the device to be used for boot console output +with a stdout-path property under /chosen, as described in ePAPR, e.g. + +/ { + chosen { + stdout-path = "/serial@f00:115200"; + }; + + serial@f00 { + compatible = "vendor,some-uart"; + reg = <0xf00 0x10>; + }; +}; + +If the character ":" is present in the value, this terminates the path. +The meaning of any characters following the ":" is device-specific, and +must be specified in the relevant binding documentation. + +For UART devices, the preferred binding is a string in the form: + + <baud>{<parity>{<bits>{<flow>}}} + +where + + baud - baud rate in decimal + parity - 'n' (none), 'o', (odd) or 'e' (even) + bits - number of data bits + flow - 'r' (rts) + +For example: 115200n8r + +Implementation note: Linux will look for the property "linux,stdout-path" or +on PowerPC "stdout" if "stdout-path" is not found. However, the +"linux,stdout-path" and "stdout" properties are deprecated. New platforms +should only use the "stdout-path" property. diff --git a/Documentation/devicetree/bindings/clock/arm-integrator.txt b/Documentation/devicetree/bindings/clock/arm-integrator.txt index ecc69520bcea..11f5f95f571b 100644 --- a/Documentation/devicetree/bindings/clock/arm-integrator.txt +++ b/Documentation/devicetree/bindings/clock/arm-integrator.txt @@ -1,6 +1,6 @@ Clock bindings for ARM Integrator and Versatile Core Module clocks -Auxilary Oscillator Clock +Auxiliary Oscillator Clock This is a configurable clock fed from a 24 MHz chrystal, used for generating e.g. video clocks. It is located on the diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index b3d544ca522a..7a4d4926f44e 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -74,6 +74,9 @@ Required properties: "atmel,at91sam9x5-clk-utmi": at91 utmi clock + "atmel,sama5d4-clk-h32mx": + at91 h32mx clock + Required properties for SCKC node: - reg : defines the IO memory reserved for the SCKC. - #size-cells : shall be 0 (reg is used to encode clk id). @@ -447,3 +450,14 @@ For example: #clock-cells = <0>; clocks = <&main>; }; + +Required properties for 32 bits bus Matrix clock (h32mx clock): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock source phandle. + +For example: + h32ck: h32mxck { + #clock-cells = <0>; + compatible = "atmel,sama5d4-clk-h32mx"; + clocks = <&mck>; + }; diff --git a/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt b/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt new file mode 100644 index 000000000000..00d26edec8bc --- /dev/null +++ b/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt @@ -0,0 +1,34 @@ +Broadcom Cygnus Clocks + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +Currently various "fixed" clocks are declared for peripheral drivers that use +the common clock framework to reference their core clocks. Proper support of +these clocks will be added later + +Device tree example: + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <25000000>; + }; + + apb_clk: apb_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + }; + + periph_clk: periph_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt index aadc9c59e2d1..f57d9dd9ea85 100644 --- a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -7,6 +7,8 @@ Required Properties: - compatible: should be one of the following. - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. + - "samsung,exynos3250-cmu-dmc" - controller compatible with + Exynos3250 SoC for Dynamic Memory Controller domain. - reg: physical base address of the controller and length of memory mapped region. @@ -20,7 +22,7 @@ All available clocks are defined as preprocessor macros in dt-bindings/clock/exynos3250.h header and can be used in device tree sources. -Example 1: An example of a clock controller node is listed below. +Example 1: Examples of clock controller nodes are listed below. cmu: clock-controller@10030000 { compatible = "samsung,exynos3250-cmu"; @@ -28,6 +30,12 @@ Example 1: An example of a clock controller node is listed below. #clock-cells = <1>; }; + cmu_dmc: clock-controller@105C0000 { + compatible = "samsung,exynos3250-cmu-dmc"; + reg = <0x105C0000 0x2000>; + #clock-cells = <1>; + }; + Example 2: UART controller node that consumes the clock generated by the clock controller. Refer to the standard clock bindings for information about 'clocks' and 'clock-names' property. diff --git a/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt new file mode 100644 index 000000000000..d3379ff9b84b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt @@ -0,0 +1,21 @@ +Binding for simple gpio gated clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-gate-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- enable-gpios : GPIO reference for enabling and disabling the clock. + +Optional properties: +- clocks: Maximum of one parent clock is supported. + +Example: + clock { + compatible = "gpio-gate-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + enable-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt index 96ce71bbd745..9c40739a661a 100644 --- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt +++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt @@ -9,13 +9,21 @@ The MAX77686 contains three 32.768khz clock outputs that can be controlled Following properties should be presend in main device node of the MFD chip. Required properties: -- #clock-cells: simple one-cell clock specifier format is used, where the - only cell is used as an index of the clock inside the provider. Following - indices are allowed: + +- #clock-cells: from common clock binding; shall be set to 1. + +Optional properties: +- clock-output-names: From common clock binding. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: - 0: 32khz_ap clock, - 1: 32khz_cp clock, - 2: 32khz_pmic clock. +Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h +header and can be used in device tree sources. + Example: Node of the MFD chip max77686: max77686@09 { @@ -34,5 +42,5 @@ Example: Clock consumer node compatible = "bar,foo"; /* ... */ clock-names = "my-clock"; - clocks = <&max77686 2>; + clocks = <&max77686 MAX77686_CLK_PMIC>; }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max77802.txt b/Documentation/devicetree/bindings/clock/maxim,max77802.txt new file mode 100644 index 000000000000..c6dc7835f06c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/maxim,max77802.txt @@ -0,0 +1,44 @@ +Binding for Maxim MAX77802 32k clock generator block + +This is a part of device tree bindings of MAX77802 multi-function device. +More information can be found in bindings/mfd/max77802.txt file. + +The MAX77802 contains two 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. + +Following properties should be present in main device node of the MFD chip. + +Required properties: +- #clock-cells: From common clock binding; shall be set to 1. + +Optional properties: +- clock-output-names: From common clock binding. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: 32khz_ap clock, + - 1: 32khz_cp clock. + +Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77802.h +header and can be used in device tree sources. + +Example: Node of the MFD chip + + max77802: max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + +Example: Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77802 MAX77802_CLK_32K_AP>; + }; diff --git a/Documentation/devicetree/bindings/clock/pxa-clock.txt b/Documentation/devicetree/bindings/clock/pxa-clock.txt new file mode 100644 index 000000000000..4b4a9024bd99 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pxa-clock.txt @@ -0,0 +1,16 @@ +* Clock bindings for Marvell PXA chips + +Required properties: +- compatible: Should be "marvell,pxa-clocks" +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell (see include/.../pxa-clock.h). + +Examples: + +pxa2xx_clks: pxa2xx_clks@41300004 { + compatible = "marvell,pxa-clocks"; + #clock-cells = <1>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 5666812fc42b..266ff9d23229 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -62,6 +62,8 @@ Required properties: It takes parent's clock-frequency as its clock. * "fsl,qoriq-sysclk-2.0": for input system clock (v2.0). It takes parent's clock-frequency as its clock. + * "fsl,qoriq-platform-pll-1.0" for the platform PLL clock (v1.0) + * "fsl,qoriq-platform-pll-2.0" for the platform PLL clock (v2.0) - #clock-cells: From common clock binding. The number of cells in a clock-specifier. Should be <0> for "fsl,qoriq-sysclk-[1,2].0" clocks, or <1> for "fsl,qoriq-core-pll-[1,2].0" clocks. @@ -128,8 +130,16 @@ Example for clock block and clock provider: clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2"; clock-output-names = "cmux1"; }; + + platform-pll: platform-pll@c00 { + #clock-cells = <1>; + reg = <0xc00 0x4>; + compatible = "fsl,qoriq-platform-pll-1.0"; + clocks = <&sysclk>; + clock-output-names = "platform-pll", "platform-pll-div2"; + }; }; - } +}; Example for clock consumer: @@ -139,4 +149,4 @@ Example for clock consumer: clocks = <&mux0>; ... }; - } +}; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 8a92b5fb3540..a5f52238c80d 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -11,9 +11,12 @@ Required Properties: - compatible: Must be one of the following - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks + - "renesas,r8a7740-mstp-clocks" for R8A7740 (R-Mobile A1) MSTP gate clocks - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2) MSTP gate clocks + - "renesas,r8a7794-mstp-clocks" for R8A7794 (R-Car E2) MSTP gate clocks + - "renesas,sh73a0-mstp-clocks" for SH73A0 (SH-MobileAG5) MSTP gate clocks - "renesas,cpg-mstp-clock" for generic MSTP gate clocks - reg: Base address and length of the I/O mapped registers used by the MSTP clocks. The first register is the clock control register and is mandatory. diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index 7b41c2fe54db..e6ad35b894f9 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Must be one of - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG - "renesas,rcar-gen2-cpg-clocks" for the generic R-Car Gen2 CPG - reg: Base address and length of the memory resource used by the CPG diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt index 1d3ace088172..b7ee5c7e0f75 100644 --- a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -11,7 +11,7 @@ Please find an example below: Clockgen block diagram ------------------------------------------------------------------- - | Flexgen stucture | + | Flexgen structure | | --------------------------------------------- | | | ------- -------- -------- | | clk_sysin | | | | | | | | | diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index d3a5c3c6d677..ed116df9c3e7 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -46,7 +46,11 @@ Required properties: "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 + "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 + "allwinner,sun4i-a10-mmc-output-clk" - for the MMC output clock on A10 + "allwinner,sun4i-a10-mmc-sample-clk" - for the MMC sample clock on A10 "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks + "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 diff --git a/Documentation/devicetree/bindings/clock/vf610-clock.txt b/Documentation/devicetree/bindings/clock/vf610-clock.txt index c80863d344ac..63f9f1ac3439 100644 --- a/Documentation/devicetree/bindings/clock/vf610-clock.txt +++ b/Documentation/devicetree/bindings/clock/vf610-clock.txt @@ -5,6 +5,19 @@ Required properties: - reg: Address and length of the register set - #clock-cells: Should be <1> +Optional properties: +- clocks: list of clock identifiers which are external input clocks to the + given clock controller. Please refer the next section to find + the input clocks for a given controller. +- clock-names: list of names of clocks which are exteral input clocks to the + given clock controller. + +Input clocks for top clock controller: + - sxosc (external crystal oscillator 32KHz, recommended) + - fxosc (external crystal oscillator 24MHz, recommended) + - audio_ext + - enet_ext + The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. See include/dt-bindings/clock/vf610-clock.h for the full list of VF610 clock IDs. @@ -15,6 +28,8 @@ clks: ccm@4006b000 { compatible = "fsl,vf610-ccm"; reg = <0x4006b000 0x1000>; #clock-cells = <1>; + clocks = <&sxosc>, <&fxosc>; + clock-names = "sxosc", "fxosc"; }; uart1: serial@40028000 { diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt index 366690cb86a3..e41c98ffbccb 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt @@ -1,8 +1,8 @@ -Generic CPU0 cpufreq driver +Generic cpufreq driver -It is a generic cpufreq driver for CPU0 frequency management. It -supports both uniprocessor (UP) and symmetric multiprocessor (SMP) -systems which share clock and voltage across all CPUs. +It is a generic DT based cpufreq driver for frequency management. It supports +both uniprocessor (UP) and symmetric multiprocessor (SMP) systems which share +clock and voltage across all CPUs. Both required and optional properties listed below must be defined under node /cpus/cpu@0. diff --git a/Documentation/devicetree/bindings/crypto/fsl-imx-sahara.txt b/Documentation/devicetree/bindings/crypto/fsl-imx-sahara.txt index 5c65eccd0e56..e8a35c71e947 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-imx-sahara.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-imx-sahara.txt @@ -1,5 +1,5 @@ Freescale SAHARA Cryptographic Accelerator included in some i.MX chips. -Currently only i.MX27 is supported. +Currently only i.MX27 and i.MX53 are supported. Required properties: - compatible : Should be "fsl,<soc>-sahara" diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt index c0a20cd972e3..baf8a3c1b469 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt @@ -1,5 +1,5 @@ SEC 6 is as Freescale's Cryptographic Accelerator and Assurance Module (CAAM). -Currently Freescale powerpc chip C29X is embeded with SEC 6. +Currently Freescale powerpc chip C29X is embedded with SEC 6. SEC 6 device tree binding include: -SEC 6 Node -Job Ring Node diff --git a/Documentation/devicetree/bindings/dma/atmel-xdma.txt b/Documentation/devicetree/bindings/dma/atmel-xdma.txt new file mode 100644 index 000000000000..0eb2b3207e08 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/atmel-xdma.txt @@ -0,0 +1,54 @@ +* Atmel Extensible Direct Memory Access Controller (XDMAC) + +* XDMA Controller +Required properties: +- compatible: Should be "atmel,<chip>-dma". + <chip> compatible description: + - sama5d4: first SoC adding the XDMAC +- reg: Should contain DMA registers location and length. +- interrupts: Should contain DMA interrupt. +- #dma-cells: Must be <1>, used to represent the number of integer cells in +the dmas property of client devices. + - The 1st cell specifies the channel configuration register: + - bit 13: SIF, source interface identifier, used to get the memory + interface identifier, + - bit 14: DIF, destination interface identifier, used to get the peripheral + interface identifier, + - bit 30-24: PERID, peripheral identifier. + +Example: + +dma1: dma-controller@f0004000 { + compatible = "atmel,sama5d4-dma"; + reg = <0xf0004000 0x200>; + interrupts = <50 4 0>; + #dma-cells = <1>; +}; + + +* DMA clients +DMA clients connected to the Atmel XDMA controller must use the format +described in the dma.txt file, using a one-cell specifier for each channel. +The two cells in order are: +1. A phandle pointing to the DMA controller. +2. Channel configuration register. Configurable fields are: + - bit 13: SIF, source interface identifier, used to get the memory + interface identifier, + - bit 14: DIF, destination interface identifier, used to get the peripheral + interface identifier, + - bit 30-24: PERID, peripheral identifier. + +Example: + +i2c2: i2c@f8024000 { + compatible = "atmel,at91sam9x5-i2c"; + reg = <0xf8024000 0x4000>; + interrupts = <34 4 6>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(6))>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(7))>; + dma-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 4659fd952301..dc8d3aac1aa9 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -48,6 +48,7 @@ The full ID of peripheral types can be found below. 21 ESAI 22 SSI Dual FIFO (needs firmware ver >= 2) 23 Shared ASRC + 24 SAI The third cell specifies the transfer priority as below. diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt new file mode 100644 index 000000000000..9bcab9115982 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt @@ -0,0 +1,62 @@ +QCOM ADM DMA Controller + +Required properties: +- compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 +- reg: Address range for DMA registers +- interrupts: Should contain one interrupt shared by all channels +- #dma-cells: must be <2>. First cell denotes the channel number. Second cell + denotes CRCI (client rate control interface) flow control assignment. +- clocks: Should contain the core clock and interface clock. +- clock-names: Must contain "core" for the core clock and "iface" for the + interface clock. +- resets: Must contain an entry for each entry in reset names. +- reset-names: Must include the following entries: + - clk + - c0 + - c1 + - c2 +- qcom,ee: indicates the security domain identifier used in the secure world. + +Example: + adm_dma: dma@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <0 170 0>; + #dma-cells = <2>; + + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; + + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "c0", "c1", "c2"; + qcom,ee = <0>; + }; + +DMA clients must use the format descripted in the dma.txt file, using a three +cell specifier for each channel. + +Each dmas request consists of 3 cells: + 1. phandle pointing to the DMA controller + 2. channel number + 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. + The CRCI is used for flow control. It identifies the peripheral device that + is the source/destination for the transferred data. + +Example: + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 0>; + + dmas = <&adm_dma 6 9>, + <&adm_dma 5 10>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index d75a9d767022..f8c3311b7153 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -1,7 +1,9 @@ QCOM BAM DMA controller Required properties: -- compatible: must contain "qcom,bam-v1.4.0" for MSM8974 +- compatible: must be one of the following: + * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084 + * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960 - reg: Address range for DMA registers - interrupts: Should contain the one interrupt shared by all channels - #dma-cells: must be <1>, the cell in the dmas property of the client device diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt index 3e145c1675b1..9cdcba24d7c3 100644 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -4,7 +4,7 @@ This driver follows the generic DMA bindings defined in dma.txt. Required properties: -- compatible: Must be "allwinner,sun6i-a31-dma" +- compatible: Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma" - reg: Should contain the registers base address and length - interrupts: Should contain a reference to the interrupt used by this device - clocks: Should contain a reference to the parent AHB clock diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt new file mode 100644 index 000000000000..2291c4098730 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -0,0 +1,65 @@ +Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream +target devices. It can be configured to have one channel or two channels. +If configured as two channels, one is to transmit to the device and another +is to receive from the device. + +Required properties: +- compatible: Should be "xlnx,axi-dma-1.00.a" +- #dma-cells: Should be <1>, see "dmas" property below +- reg: Should contain DMA registers location and length. +- dma-channel child node: Should have atleast one channel and can have upto + two channels per device. This node specifies the properties of each + DMA channel (see child node properties below). + +Optional properties: +- xlnx,include-sg: Tells whether configured for Scatter-mode in + the hardware. + +Required child node properties: +- compatible: It should be either "xlnx,axi-dma-mm2s-channel" or + "xlnx,axi-dma-s2mm-channel". +- interrupts: Should contain per channel DMA interrupts. +- xlnx,datawidth: Should contain the stream data width, take values + {32,64...1024}. + +Option child node properties: +- xlnx,include-dre: Tells whether hardware is configured for Data + Realignment Engine. + +Example: +++++++++ + +axi_dma_0: axidma@40400000 { + compatible = "xlnx,axi-dma-1.00.a"; + #dma_cells = <1>; + reg = < 0x40400000 0x10000 >; + dma-channel@40400000 { + compatible = "xlnx,axi-dma-mm2s-channel"; + interrupts = < 0 59 4 >; + xlnx,datawidth = <0x40>; + } ; + dma-channel@40400030 { + compatible = "xlnx,axi-dma-s2mm-channel"; + interrupts = < 0 58 4 >; + xlnx,datawidth = <0x40>; + } ; +} ; + + +* DMA client + +Required properties: +- dmas: a list of <[DMA device phandle] [Channel ID]> pairs, + where Channel ID is '0' for write/tx and '1' for read/rx + channel. +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: +++++++++ + +dmatest_0: dmatest@0 { + compatible ="xlnx,axi-dma-test-1.00.a"; + dmas = <&axi_dma_0 0 + &axi_dma_0 1>; + dma-names = "dma0", "dma1"; +} ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt index 1405ed071bb4..e4c4d47f8137 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt @@ -25,7 +25,7 @@ Required child node properties: - compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or "xlnx,axi-vdma-s2mm-channel". - interrupts: Should contain per channel VDMA interrupts. -- xlnx,data-width: Should contain the stream data width, take values +- xlnx,datawidth: Should contain the stream data width, take values {32,64...1024}. Optional child node properties: diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt index e75f0e549fff..e75f0e549fff 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt diff --git a/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt b/Documentation/devicetree/bindings/drm/imx/hdmi.txt index 1b756cf9afb0..1b756cf9afb0 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt +++ b/Documentation/devicetree/bindings/drm/imx/hdmi.txt diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/drm/imx/ldb.txt index 443bcb6134d5..443bcb6134d5 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt +++ b/Documentation/devicetree/bindings/drm/imx/ldb.txt diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt index 9301c330d1a6..4ab9e2300907 100644 --- a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -18,6 +18,10 @@ Required properties: Documentation/devicetree/bindings/video/display-timing.txt for display timing binding details. +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + Recommended properties: - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing properly for pins that connect to TFP410 device @@ -29,6 +33,9 @@ Example: compatible = "ti,tilcdc,panel"; pinctrl-names = "default"; pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + panel-info { ac-bias = <255>; ac-bias-intrpt = <0>; diff --git a/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt new file mode 100644 index 000000000000..6dede7d11532 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt @@ -0,0 +1,25 @@ + +* Richtek RT8973A - Micro USB Switch device + +The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A +is a USB port accessory detector and switch that is optimized to protect low +voltage system from abnormal high input voltage (up to 28V) and supports high +speed USB operation. Also, RT8973A support 'auto-configuration' mode. +If auto-configuration mode is enabled, RT8973A would control internal h/w patch +for USB D-/D+ switching. + +Required properties: +- compatible: Should be "richtek,rt8973a-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x14 +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from rt8973a are delivered to. +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + rt8973a@14 { + compatible = "richtek,rt8973a-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x14>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt b/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt new file mode 100644 index 000000000000..7bb1a9d60133 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt @@ -0,0 +1,30 @@ +* 74XX MMIO GPIO driver + +Required properties: +- compatible: Should contain one of the following: + "ti,741g125": for 741G125 (1-bit Input), + "ti,741g174": for 741G74 (1-bit Output), + "ti,742g125": for 742G125 (2-bit Input), + "ti,7474" : for 7474 (2-bit Output), + "ti,74125" : for 74125 (4-bit Input), + "ti,74175" : for 74175 (4-bit Output), + "ti,74365" : for 74365 (6-bit Input), + "ti,74174" : for 74174 (6-bit Output), + "ti,74244" : for 74244 (8-bit Input), + "ti,74273" : for 74273 (8-bit Output), + "ti,741624" : for 741624 (16-bit Input), + "ti,7416374": for 7416374 (16-bit Output). +- reg: Physical base address and length where IC resides. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the GPIO polarity: + 0 = Active High, + 1 = Active Low. + +Example: + ctrl: gpio@30008004 { + compatible = "ti,74174"; + reg = <0x30008004 0x1>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt new file mode 100644 index 000000000000..6c7e6c7302f5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt @@ -0,0 +1,39 @@ +Keystone 2 DSP GPIO controller bindings + +HOST OS userland running on ARM can send interrupts to DSP cores using +the DSP GPIO controller IP. It provides 28 IRQ signals per each DSP core. +This is one of the component used by the IPC mechanism used on Keystone SOCs. + +For example TCI6638K2K SoC has 8 DSP GPIO controllers: + - 8 for C66x CorePacx CPUs 0-7 + +Keystone 2 DSP GPIO controller has specific features: +- each GPIO can be configured only as output pin; +- setting GPIO value to 1 causes IRQ generation on target DSP core; +- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still + pending. + +Required Properties: +- compatible: should be "ti,keystone-dsp-gpio" +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset of device's specific + registers within device state control registers range. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be 2. + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: + dspgpio0: keystone_dsp_gpio@02620240 { + compatible = "ti,keystone-dsp-gpio"; + ti,syscon-dev = <&devctrl 0x240>; + gpio-controller; + #gpio-cells = <2>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + kick-gpio = <&dspgpio0 27>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt index c306a2d0f2b1..f3332b9a8ed4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -57,6 +57,8 @@ Optional device specific properties: occurred on. If it is not set, the interrupt are only generated for the bank they belong to. On devices with only one interrupt output this property is useless. +- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This + configures the IRQ output polarity as active high. Example I2C (with interrupt): gpiom1: gpio@20 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt new file mode 100644 index 000000000000..b9a42f294dd0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -0,0 +1,39 @@ +* NXP PCA953x I2C GPIO multiplexer + +Required properties: + - compatible: Has to contain one of the following: + nxp,pca9505 + nxp,pca9534 + nxp,pca9535 + nxp,pca9536 + nxp,pca9537 + nxp,pca9538 + nxp,pca9539 + nxp,pca9554 + nxp,pca9555 + nxp,pca9556 + nxp,pca9557 + nxp,pca9574 + nxp,pca9575 + nxp,pca9698 + maxim,max7310 + maxim,max7312 + maxim,max7313 + maxim,max7315 + ti,pca6107 + ti,tca6408 + ti,tca6416 + ti,tca6424 + exar,xra1202 + +Example: + + + gpio@20 { + compatible = "nxp,pca9505"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9505>; + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/gpio/gpio-restart.txt new file mode 100644 index 000000000000..af3701bc15c4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vf610.txt b/Documentation/devicetree/bindings/gpio/gpio-vf610.txt new file mode 100644 index 000000000000..436cc99c6598 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vf610.txt @@ -0,0 +1,55 @@ +* Freescale VF610 PORT/GPIO module + +The Freescale PORT/GPIO modules are two adjacent modules providing GPIO +functionality. Each pair serves 32 GPIOs. The VF610 has 5 instances of +each, and each PORT module has its own interrupt. + +Required properties for GPIO node: +- compatible : Should be "fsl,<soc>-gpio", currently "fsl,vf610-gpio" +- reg : The first reg tuple represents the PORT module, the second tuple + the GPIO module. +- interrupts : Should be the port interrupt shared by all 32 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Examples: + +aliases { + gpio0 = &gpio1; + gpio1 = &gpio2; +}; + +gpio1: gpio@40049000 { + compatible = "fsl,vf610-gpio"; + reg = <0x40049000 0x1000 0x400ff000 0x40>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 0 32>; +}; + +gpio2: gpio@4004a000 { + compatible = "fsl,vf610-gpio"; + reg = <0x4004a000 0x1000 0x400ff040 0x40>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 32 32>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt new file mode 100644 index 000000000000..86dbb05e7758 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt @@ -0,0 +1,22 @@ +APM X-Gene SoC GPIO controller bindings + +This is a gpio controller that is part of the flash controller. +This gpio controller controls a total of 48 gpios. + +Required properties: +- compatible: "apm,xgene-gpio" for X-Gene GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio0: gpio0@1701c000 { + compatible = "apm,xgene-gpio"; + reg = <0x0 0x1701c000 0x0 0x40>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 3fb8f53071b8..b9bd1d64cfa6 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -13,13 +13,22 @@ properties, each containing a 'gpio-list': gpio-specifier : Array of #gpio-cells specifying specific gpio (controller specific) -GPIO properties should be named "[<name>-]gpios". The exact -meaning of each gpios property must be documented in the device tree -binding for each device. +GPIO properties should be named "[<name>-]gpios", with <name> being the purpose +of this GPIO for the device. While a non-existent <name> is considered valid +for compatibility reasons (resolving to the "gpios" property), it is not allowed +for new bindings. -For example, the following could be used to describe GPIO pins used -as chip select lines; with chip selects 0, 1 and 3 populated, and chip -select 2 left empty: +GPIO properties can contain one or more GPIO phandles, but only in exceptional +cases should they contain more than one. If your device uses several GPIOs with +distinct functions, reference each of them under its own property, giving it a +meaningful name. The only case where an array of GPIOs is accepted is when +several GPIOs serve the same function (e.g. a parallel data line). + +The exact purpose of each gpios property must be documented in the device tree +binding of the device. + +The following example could be used to describe GPIO pins used as device enable +and bit-banged data signals: gpio1: gpio1 { gpio-controller @@ -30,10 +39,12 @@ select 2 left empty: #gpio-cells = <1>; }; [...] - chipsel-gpios = <&gpio1 12 0>, - <&gpio1 13 0>, - <0>, /* holes are permitted, means no GPIO 2 */ - <&gpio2 2>; + + enable-gpios = <&gpio2 2>; + data-gpios = <&gpio1 12 0>, + <&gpio1 13 0>, + <&gpio1 14 0>, + <&gpio1 15 0>; Note that gpio-specifier length is controller dependent. In the above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 @@ -42,16 +53,17 @@ only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. +be documented in the device tree binding for the device. Use the macros +defined in include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: node { - gpios = <&qe_pio_e 18 0>; + enable-gpios = <&qe_pio_e 18 GPIO_ACTIVE_HIGH>; }; -In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and GPIO flags as accepted by the "qe_pio_e" gpio-controller. +GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes +GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. 1.1) GPIO specifier best practices ---------------------------------- diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 66416261e14d..b2afdb27adeb 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -19,7 +19,7 @@ Required properties: - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be one. It is the pin number. -Example: +Example for a MMP platform: gpio: gpio@d4019000 { compatible = "marvell,mmp-gpio"; @@ -32,6 +32,19 @@ Example: #interrupt-cells = <1>; }; +Example for a PXA3xx platform: + + gpio: gpio@40e00000 { + compatible = "intel,pxa3xx-gpio"; + reg = <0x40e00000 0x10000>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + interrupts = <8 9 10>; + gpio-controller; + #gpio-cells = <0x2>; + interrupt-controller; + #interrupt-cells = <0x2>; + }; + * Marvell Orion GPIO Controller Required properties: diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt index a2c416bcbccc..89058d375b7c 100644 --- a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt @@ -7,4 +7,4 @@ Required properties: - bit 0 specifies polarity (0 for normal, 1 for inverted) - gpio-controller : Marks the device node as a GPIO controller. - interrupts : Interrupt mapping for GPIO IRQ. - +- gpio-ranges : Interaction with the PINCTRL subsystem. diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 941a26aa4322..38fb86f28ba2 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -6,7 +6,9 @@ Required Properties: - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. - - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2) compatible GPIO controller. + - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. + - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. + - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-rcar": for generic R-Car GPIO controller. - reg: Base address and length of each memory resource used by the GPIO diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index b48f4ef31d93..4c32ef0b7db8 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -191,6 +191,8 @@ of the following host1x client modules: - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - nvidia,edid: supplies a binary EDID blob - nvidia,panel: phandle of a display panel + - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang + up with in order to support up to 8 data lanes - sor: serial output resource diff --git a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt index 2d150c311a05..c99eb34e640b 100644 --- a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt +++ b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt @@ -68,7 +68,7 @@ STMicroelectronics stih4xx platforms number of clocks may depend of the SoC type. - clock-names: names of the clocks listed in clocks property in the same order. - - hdmi,hpd-gpio: gpio id to detect if an hdmi cable is plugged or not. + - ddc: phandle of an I2C controller used for DDC EDID probing sti-hda: Required properties: @@ -83,6 +83,22 @@ sti-hda: - clock-names: names of the clocks listed in clocks property in the same order. +sti-hqvdp: + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-hqvdp" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + - st,vtg: phandle on vtg main device node. + Example: / { @@ -173,7 +189,6 @@ Example: interrupt-names = "irq"; clock-names = "pix", "tmds", "phy", "audio"; clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>; - hdmi,hpd-gpio = <&PIO2 5>; }; sti-hda@fe85a000 { @@ -184,6 +199,16 @@ Example: clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>; }; }; + + sti-hqvdp@9c000000 { + compatible = "st,stih407-hqvdp"; + reg = <0x9C00000 0x100000>; + clock-names = "hqvdp", "pix_main"; + clocks = <&clk_s_c0_flexgen CLK_MAIN_DISP>, <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>; + reset-names = "hqvdp"; + resets = <&softreset STIH407_HDQVDP_SOFTRESET>; + st,vtg = <&vtg_main>; + }; }; ... }; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt new file mode 100644 index 000000000000..ed2f09dc2483 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -0,0 +1,39 @@ +ltc2978 + +Required properties: +- compatible: should contain one of: + * "lltc,ltc2974" + * "lltc,ltc2977" + * "lltc,ltc2978" + * "lltc,ltc3880" + * "lltc,ltc3883" + * "lltc,ltm4676" +- reg: I2C slave address + +Optional properties: +- regulators: A node that houses a sub-node for each regulator controlled by + the device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + +Valid names of regulators depend on number of supplies supported per device: + * ltc2974 : vout0 - vout3 + * ltc2977 : vout0 - vout7 + * ltc2978 : vout0 - vout7 + * ltc3880 : vout0 - vout1 + * ltc3883 : vout0 + * ltm4676 : vout0 - vout1 + +Example: +ltc2978@5e { + compatible = "lltc,ltc2978"; + reg = <0x5e>; + regulators { + vout0 { + regulator-name = "FPGA-2.5V"; + }; + vout2 { + regulator-name = "FPGA-1.5V"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index 2391e5c41999..fcca8e744f41 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -25,6 +25,9 @@ Requires node properties: - "io-channels" Channel node of ADC to be used for conversion. +Optional node properties: +- "#thermal-sensor-cells" Used to expose itself to thermal fw. + Read more about iio bindings at Documentation/devicetree/bindings/iio/iio-bindings.txt diff --git a/Documentation/devicetree/bindings/hwrng/atmel-trng.txt b/Documentation/devicetree/bindings/hwrng/atmel-trng.txt new file mode 100644 index 000000000000..4ac5aaa2d024 --- /dev/null +++ b/Documentation/devicetree/bindings/hwrng/atmel-trng.txt @@ -0,0 +1,16 @@ +Atmel TRNG (True Random Number Generator) block + +Required properties: +- compatible : Should be "atmel,at91sam9g45-trng" +- reg : Offset and length of the register set of this block +- interrupts : the interrupt number for the TRNG block +- clocks: should contain the TRNG clk source + +Example: + +trng@fffcc000 { + compatible = "atmel,at91sam9g45-trng"; + reg = <0xfffcc000 0x4000>; + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&trng_clk>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-axxia.txt b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt new file mode 100644 index 000000000000..2296d782b4c2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt @@ -0,0 +1,30 @@ +LSI Axxia I2C + +Required properties : +- compatible : Must be "lsi,api2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "i2c". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + +i2c@02010084000 { + compatible = "lsi,api2c"; + device_type = "i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x20 0x10084000 0x00 0x1000>; + interrupts = <0 19 4>; + clocks = <&clk_per>; + clock-names = "i2c"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index 5199b0c8cf7a..fee26dc3e858 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -14,10 +14,10 @@ Optional properties : - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer. - - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds. + - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds. This value which is by default 300ns is used to compute the tLOW period. - - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds. + - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds. This value which is by default 300ns is used to compute the tHIGH period. Example : diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt index d4745e31f5c6..2dbc0b62daa6 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -12,6 +12,8 @@ Required properties: on Exynos5250 and Exynos5420 SoCs. -> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available on Exynos5260 SoCs. + -> "samsung,exynos7-hsi2c", for i2c compatible with HSI2C available + on Exynos7 SoCs. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt new file mode 100644 index 000000000000..f98b37401e6e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt @@ -0,0 +1,24 @@ +I2C for Hisilicon hix5hd2 chipset platform + +Required properties: +- compatible: Must be "hisilicon,hix5hd2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- Child nodes conforming to i2c bus binding + +Examples: +I2C0@f8b10000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0xf8b10000 0x1000>; + interrupts = <0 38 4>; + clocks = <&clock HIX5HD2_I2C0_RST>; + #address-cells = <1>; + #size-cells = <0>; +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt new file mode 100644 index 000000000000..b6461602dca5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt @@ -0,0 +1,26 @@ +IMG Serial Control Bus (SCB) I2C Controller + +Required Properties: +- compatible: "img,scb-i2c" +- reg: Physical base address and length of controller registers +- interrupts: Interrupt number used by the controller +- clocks : Should contain a clock specifier for each entry in clock-names +- clock-names : Should contain the following entries: + "scb", for the SCB core clock. + "sys", for the system clock. +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Example: + +i2c@18100000 { + compatible = "img,scb-i2c"; + reg = <0x18100000 0x200>; + interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c0_clk>, <&system_clk>; + clock-names = "scb", "sys"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 4a8513e44740..52d37fd8d3e5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -11,6 +11,8 @@ Required properties: Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. The absence of the propoerty indicates the default frequency 100 kHz. +- dmas: A list of two dma specifiers, one for each entry in dma-names. +- dma-names: should contain "tx" and "rx". Examples: @@ -26,3 +28,12 @@ i2c@70038000 { /* HS-I2C on i.MX51 */ interrupts = <64>; clock-frequency = <400000>; }; + +i2c0: i2c@40066000 { /* i2c0 on vf610 */ + compatible = "fsl,vf610-i2c"; + reg = <0x40066000 0x1000>; + interrupts =<0 71 0x04>; + dmas = <&edma0 0 50>, + <&edma0 0 51>; + dma-names = "rx","tx"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt new file mode 100644 index 000000000000..682f9a6f766e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt @@ -0,0 +1,24 @@ +Amlogic Meson I2C controller + +Required properties: + - compatible: must be "amlogic,meson6-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Examples: + + i2c@c8100500 { + compatible = "amlogic,meson6-i2c"; + reg = <0xc8100500 0x20>; + interrupts = <0 92 1>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index 278de8e64bbf..89b3250f049b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -32,6 +32,7 @@ Optional properties: specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not specified, the default value in Hz is 100000. + - samsung,sysreg-phandle - handle to syscon used to control the system registers Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index d2153ce36fa8..2bfc6e7ed094 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -2,6 +2,15 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: - compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback + Examples with soctypes are: + - "renesas,iic-r8a73a4" (R-Mobile APE6) + - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7790" (R-Car H2) + - "renesas,iic-r8a7791" (R-Car M2-W) + - "renesas,iic-r8a7792" (R-Car V2H) + - "renesas,iic-r8a7793" (R-Car M2-N) + - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-sh73a0" (SH-Mobile AG5) - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -10,6 +19,11 @@ Required properties: Optional properties: - clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + Pinctrl properties might be needed, too. See there. diff --git a/Documentation/devicetree/bindings/i2c/ti,bq32k.txt b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt new file mode 100644 index 000000000000..e204906b9ad3 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt @@ -0,0 +1,18 @@ +* TI BQ32000 I2C Serial Real-Time Clock + +Required properties: +- compatible: Should contain "ti,bq32000". +- reg: I2C address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable are 1120 and 20180 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + bq32000: rtc@68 { + compatible = "ti,bq32000"; + trickle-resistor-ohms = <1120>; + reg = <0x68>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 6af570ec53b4..9f4e3824e71e 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -17,6 +17,9 @@ adi,adt7473 +/-1C TDM Extended Temp Range I.C adi,adt7475 +/-1C TDM Extended Temp Range I.C adi,adt7476 +/-1C TDM Extended Temp Range I.C adi,adt7490 +/-1C TDM Extended Temp Range I.C +adi,adxl345 Three-Axis Digital Accelerometer +adi,adxl346 Three-Axis Digital Accelerometer +adi,adxl34x Three-Axis Digital Accelerometer at,24c08 i2c serial eeprom (24cxx) atmel,24c00 i2c serial eeprom (24cxx) atmel,24c01 i2c serial eeprom (24cxx) @@ -35,7 +38,6 @@ catalyst,24c32 i2c serial eeprom cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock dallas,ds1338 I2C RTC with 56-Byte NV RAM -dallas,ds1339 I2C Serial Real-Time Clock dallas,ds1340 I2C RTC with Trickle Charger dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1631 High-Precision Digital Thermometer @@ -44,7 +46,7 @@ dallas,ds1775 Tiny Digital Thermometer and Thermostat dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat -dialog,da9053 DA9053: flexible system level PMIC with multicore support +dlg,da9053 DA9053: flexible system level PMIC with multicore support epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer @@ -57,6 +59,8 @@ gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire In infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) isl,isl12057 Intersil ISL12057 I2C RTC Chip +isil,isl29028 (deprecated, use isl) +isl,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface @@ -75,7 +79,12 @@ ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI an pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) +ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt new file mode 100644 index 000000000000..4e36d6e2f7b6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt @@ -0,0 +1,46 @@ +Qualcomm's SPMI PMIC current ADC + +QPNP PMIC current ADC (IADC) provides interface to clients to read current. +A 16 bit ADC is used for current measurements. IADC can measure the current +through an external resistor (channel 1) or internal (built-in) resistor +(channel 0). When using an external resistor it is to be described by +qcom,external-resistor-micro-ohms property. + +IADC node: + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,spmi-iadc". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: IADC base address and length in the SPMI PMIC register map + +- interrupts: + Usage: optional + Value type: <prop-encoded-array> + Definition: End of ADC conversion. + +- qcom,external-resistor-micro-ohms: + Usage: optional + Value type: <u32> + Definition: Sense resister value in micro Ohm. + If not defined value of 10000 micro Ohms will be used. + +Example: + /* IADC node */ + pmic_iadc: iadc@3600 { + compatible = "qcom,spmi-iadc"; + reg = <0x3600 0x100>; + interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; + qcom,external-resistor-micro-ohms = <10000>; + #io-channel-cells = <1>; + }; + + /* IIO client node */ + bat { + io-channels = <&pmic_iadc 0>; + io-channel-names = "iadc"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt new file mode 100644 index 000000000000..a9a5fe19ff2a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -0,0 +1,24 @@ +Rockchip Successive Approximation Register (SAR) A/D Converter bindings + +Required properties: +- compatible: Should be "rockchip,saradc" or "rockchip,rk3066-tsadc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "saradc" for the converter-clock, and "apb_pclk" for + the peripheral clock. +- vref-supply: The regulator supply ADC reference voltage. +- #io-channel-cells: Should be 1, see ../iio-bindings.txt + +Example: + saradc: saradc@2006c000 { + compatible = "rockchip,saradc"; + reg = <0x2006c000 0x100>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; + clock-names = "saradc", "apb_pclk"; + #io-channel-cells = <1>; + vref-supply = <&vcc18>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt index dcebff1928e1..1a4a43d5c9ea 100644 --- a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt @@ -9,7 +9,7 @@ Required properties: - interrupts: Should contain the interrupt for the device - clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock. - clock-names: Must contain "adc", matching entry in the clocks property. -- vref-supply: The regulator supply ADC refrence voltage. +- vref-supply: The regulator supply ADC reference voltage. Example: adc0: adc@4003b000 { diff --git a/Documentation/devicetree/bindings/iio/dac/max5821.txt b/Documentation/devicetree/bindings/iio/dac/max5821.txt new file mode 100644 index 000000000000..54276ce8c971 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/max5821.txt @@ -0,0 +1,14 @@ +Maxim max5821 DAC device driver + +Required properties: + - compatible: Must be "maxim,max5821" + - reg: Should contain the DAC I2C address + - vref-supply: Phandle to the vref power supply + +Example: + + max5821@38 { + compatible = "maxim,max5821"; + reg = <0x38>; + vref-supply = <®_max5821>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt index 2742e9cfd6b1..f292917fa00d 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "atmel,<chip>-aic" - <chip> can be "at91rm9200" or "sama5d3" + <chip> can be "at91rm9200", "sama5d3" or "sama5d4" - interrupt-controller: Identifies the node as an interrupt controller. - interrupt-parent: For single AIC system, it is an empty property. - #interrupt-cells: The number of cells to define the interrupts. It should be 3. diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt new file mode 100644 index 000000000000..bae1f2187226 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt @@ -0,0 +1,96 @@ +Broadcom BCM7120-style Level 2 interrupt controller + +This interrupt controller hardware is a second level interrupt controller that +is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based +platforms. It can be found on BCM7xxx products starting with BCM7120. + +Such an interrupt controller has the following hardware design: + +- outputs multiple interrupts signals towards its interrupt controller parent + +- controls how some of the interrupts will be flowing, whether they will + directly output an interrupt signal towards the interrupt controller parent, + or if they will output an interrupt signal at this 2nd level interrupt + controller, in particular for UARTs + +- typically has one 32-bit enable word and one 32-bit status word, but on + some hardware may have more than one enable/status pair + +- no atomic set/clear operations + +- not all bits within the interrupt controller actually map to an interrupt + +The typical hardware layout for this controller is represented below: + +2nd level interrupt line Outputs for the parent controller (e.g: ARM GIC) + +0 -----[ MUX ] ------------|==========> GIC interrupt 75 + \-----------\ + | +1 -----[ MUX ] --------)---|==========> GIC interrupt 76 + \------------| + | +2 -----[ MUX ] --------)---|==========> GIC interrupt 77 + \------------| + | +3 ---------------------| +4 ---------------------| +5 ---------------------| +7 ---------------------|---|===========> GIC interrupt 66 +9 ---------------------| +10 --------------------| +11 --------------------/ + +6 ------------------------\ + |===========> GIC interrupt 64 +8 ------------------------/ + +12 ........................ X +13 ........................ X (not connected) +.. +31 ........................ X + +Required properties: + +- compatible: should be "brcm,bcm7120-l2-intc" +- reg: specifies the base physical address and size of the registers; + multiple pairs may be specified, with the first pair handling IRQ offsets + 0..31 and the second pair handling 32..63 +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node, valid values depend on the type of parent interrupt controller +- brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts + are wired to this 2nd level interrupt controller, and how they match their + respective interrupt parents. Should match exactly the number of interrupts + specified in the 'interrupts' property, multiplied by the number of + enable/status register pairs implemented by this controller. For + multiple parent IRQs with multiple enable/status words, this looks like: + <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...> + +Optional properties: + +- brcm,irq-can-wake: if present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +- brcm,int-fwd-mask: if present, a bit mask to configure the interrupts which + have a mux gate, typically UARTs. Setting these bits will make their + respective interrupt outputs bypass this 2nd level interrupt controller + completely; it is completely transparent for the interrupt controller + parent. This should have one 32-bit word per enable/status pair. + +Example: + +irq0_intc: interrupt-controller@f0406800 { + compatible = "brcm,bcm7120-l2-intc"; + interrupt-parent = <&intc>; + #interrupt-cells = <1>; + reg = <0xf0406800 0x8>; + interrupt-controller; + interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>; + brcm,int-map-mask = <0xeb8>, <0x140>; + brcm,int-fwd-mask = <0x7>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index ce6a1a072028..8a3c40829899 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -30,10 +30,6 @@ should only be used when a device has multiple interrupt parents. Example: interrupts-extended = <&intc1 5 1>, <&intc2 1 0>; -A device node may contain either "interrupts" or "interrupts-extended", but not -both. If both properties are present, then the operating system should log an -error and use only the data in "interrupts". - 2) Interrupt controller nodes ----------------------------- diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt new file mode 100644 index 000000000000..5a65478e5d40 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -0,0 +1,55 @@ +MIPS Global Interrupt Controller (GIC) + +The MIPS GIC routes external interrupts to individual VPEs and IRQ pins. +It also supports local (per-processor) interrupts and software-generated +interrupts which can be used as IPIs. The GIC also includes a free-running +global timer, per-CPU count/compare timers, and a watchdog. + +Required properties: +- compatible : Should be "mti,gic". +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt specifier. Should be 3. + - The first cell is the type of interrupt, local or shared. + See <include/dt-bindings/interrupt-controller/mips-gic.h>. + - The second cell is the GIC interrupt number. + - The third cell encodes the interrupt flags. + See <include/dt-bindings/interrupt-controller/irq.h> for a list of valid + flags. + +Optional properties: +- reg : Base address and length of the GIC registers. If not present, + the base address reported by the hardware GCR_GIC_BASE will be used. +- mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors + to which the GIC may not route interrupts. Valid values are 2 - 7. + This property is ignored if the CPU is started in EIC mode. + +Required properties for timer sub-node: +- compatible : Should be "mti,gic-timer". +- interrupts : Interrupt for the GIC local timer. +- clock-frequency : Clock frequency at which the GIC timers operate. + +Example: + + gic: interrupt-controller@1bdc0000 { + compatible = "mti,gic"; + reg = <0x1bdc0000 0x20000>; + + interrupt-controller; + #interrupt-cells = <3>; + + mti,reserved-cpu-vectors = <7>; + + timer { + compatible = "mti,gic-timer"; + interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>; + clock-frequency = <50000000>; + }; + }; + + uart@18101400 { + ... + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>; + ... + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt index 1f8b0c507c26..c73acd060093 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt @@ -2,7 +2,13 @@ DT bindings for the R-/SH-Mobile irqpin controller Required properties: -- compatible: has to be "renesas,intc-irqpin" +- compatible: has to be "renesas,intc-irqpin-<soctype>", "renesas,intc-irqpin" + as fallback. + Examples with soctypes are: + - "renesas,intc-irqpin-r8a7740" (R-Mobile A1) + - "renesas,intc-irqpin-r8a7778" (R-Car M1A) + - "renesas,intc-irqpin-r8a7779" (R-Car H1) + - "renesas,intc-irqpin-sh73a0" (SH-Mobile AG5) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt new file mode 100644 index 000000000000..1a88e62228e5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -0,0 +1,32 @@ +DT bindings for the R-Mobile/R-Car interrupt controller + +Required properties: + +- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. + Examples with soctypes are: + - "renesas,irqc-r8a73a4" (R-Mobile AP6) + - "renesas,irqc-r8a7790" (R-Car H2) + - "renesas,irqc-r8a7791" (R-Car M2-W) + - "renesas,irqc-r8a7792" (R-Car V2H) + - "renesas,irqc-r8a7793" (R-Car M2-N) + - "renesas,irqc-r8a7794" (R-Car E2) +- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in + interrupts.txt in this directory + +Optional properties: + +- any properties, listed in interrupts.txt, and any standard resource allocation + properties + +Example: + + irqc0: interrupt-controller@e61c0000 { + compatible = "renesas,irqc-r8a7790", "renesas,irqc"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0 0xe61c0000 0 0x200>; + interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>, + <0 1 IRQ_TYPE_LEVEL_HIGH>, + <0 2 IRQ_TYPE_LEVEL_HIGH>, + <0 3 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt new file mode 100644 index 000000000000..d9bb106bdd16 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt @@ -0,0 +1,36 @@ +Keystone 2 IRQ controller IP + +On Keystone SOCs, DSP cores can send interrupts to ARM +host using the IRQ controller IP. It provides 28 IRQ signals to ARM. +The IRQ handler running on HOST OS can identify DSP signal source by +analyzing SRCCx bits in IPCARx registers. This is one of the component +used by the IPC mechanism used on Keystone SOCs. + +Required Properties: +- compatible: should be "ti,keystone-irq" +- ti,syscon-dev : phandle and offset pair. The phandle to syscon used to + access device control registers and the offset inside + device control registers range. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode interrupt + source should be 1. +- interrupts: interrupt reference to primary interrupt controller + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +Example: + kirq0: keystone_irq0@026202a0 { + compatible = "ti,keystone-irq"; + ti,syscon-dev = <&devctrl 0x2a0>; + interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + interrupt-parent = <&kirq0>; + interrupts = <10 2>; + }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index 2d0f7cd867ea..06760503a819 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -14,6 +14,7 @@ conditions. "arm,smmu-v1" "arm,smmu-v2" "arm,mmu-400" + "arm,mmu-401" "arm,mmu-500" depending on the particular implementation and/or the diff --git a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt new file mode 100644 index 000000000000..9a55ac3735e5 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt @@ -0,0 +1,26 @@ +Rockchip IOMMU +============== + +A Rockchip DRM iommu translates io virtual addresses to physical addresses for +its master device. Each slave device is bound to a single master device, and +shares its clocks, power domain and irq. + +Required properties: +- compatible : Should be "rockchip,iommu" +- reg : Address space for the configuration registers +- interrupts : Interrupt specifier for the IOMMU instance +- interrupt-names : Interrupt name for the IOMMU instance +- #iommu-cells : Should be <0>. This indicates the iommu is a + "single-master" device, and needs no additional information + to associate with its master device. See: + Documentation/devicetree/bindings/iommu/iommu.txt + +Example: + + vopl_mmu: iommu@ff940300 { + compatible = "rockchip,iommu"; + reg = <0xff940300 0x100>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "vopl_mmu"; + #iommu-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-lp8860.txt b/Documentation/devicetree/bindings/leds/leds-lp8860.txt new file mode 100644 index 000000000000..aad38dd94d4b --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lp8860.txt @@ -0,0 +1,29 @@ +* Texas Instruments - lp8860 4-Channel LED Driver + +The LP8860-Q1 is an high-efficiency LED +driver with boost controller. It has 4 high-precision +current sinks that can be controlled by a PWM input +signal, a SPI/I2C master, or both. + +Required properties: + - compatible: + "ti,lp8860" + - reg - I2C slave address + - label - Used for naming LEDs + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - supply - "vled" - LED supply + +Example: + +leds: leds@6 { + compatible = "ti,lp8860"; + reg = <0x2d>; + label = "display_cluster"; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + vled-supply = <&vbatt>; +} + +For more product information please see the link below: +http://www.ti.com/product/lp8860-q1 diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt new file mode 100644 index 000000000000..379cefdc0bda --- /dev/null +++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt @@ -0,0 +1,99 @@ +Device Tree Bindings for Register Bit LEDs + +Register bit leds are used with syscon multifunctional devices +where single bits in a certain register can turn on/off a +single LED. The register bit LEDs appear as children to the +syscon device, with the proper compatible string. For the +syscon bindings see: +Documentation/devicetree/bindings/mfd/syscon.txt + +Each LED is represented as a sub-node of the syscon device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: + +Required properties: +- compatible : must be "register-bit-led" +- offset : register offset to the register controlling this LED +- mask : bit mask for the bit controlling this LED in the register + typically 0x01, 0x02, 0x04 ... + +Optional properties: +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- default-state: (optional) The initial state of the LED. Valid + values are "on", "off", and "keep". If the LED is already on or off + and the default-state property is set the to same value, then no + glitch should be produced where the LED momentarily turns off (or + on). The "keep" setting will keep the LED at whatever its current + state is, without producing a glitch. The default is off if this + property is not present. + +Example: + +syscon: syscon@10000000 { + compatible = "arm,realview-pb1176-syscon", "syscon"; + reg = <0x10000000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "versatile:0"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + led@08.1 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x02>; + label = "versatile:1"; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + led@08.2 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x04>; + label = "versatile:2"; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + led@08.3 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x08>; + label = "versatile:3"; + default-state = "off"; + }; + led@08.4 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x10>; + label = "versatile:4"; + default-state = "off"; + }; + led@08.5 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x20>; + label = "versatile:5"; + default-state = "off"; + }; + led@08.6 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x40>; + label = "versatile:6"; + default-state = "off"; + }; + led@08.7 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x80>; + label = "versatile:7"; + default-state = "off"; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/mailbox.txt b/Documentation/devicetree/bindings/mailbox/mailbox.txt new file mode 100644 index 000000000000..1a2cd3d266db --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/mailbox.txt @@ -0,0 +1,38 @@ +* Generic Mailbox Controller and client driver bindings + +Generic binding to provide a way for Mailbox controller drivers to +assign appropriate mailbox channel to client drivers. + +* Mailbox Controller + +Required property: +- #mbox-cells: Must be at least 1. Number of cells in a mailbox + specifier. + +Example: + mailbox: mailbox { + ... + #mbox-cells = <1>; + }; + + +* Mailbox Client + +Required property: +- mboxes: List of phandle and mailbox channel specifiers. + +Optional property: +- mbox-names: List of identifier strings for each mailbox channel + required by the client. The use of this property + is discouraged in favor of using index in list of + 'mboxes' while requesting a mailbox. Instead the + platforms may define channel indices, in DT headers, + to something legible. + +Example: + pwr_cntrl: power { + ... + mbox-names = "pwr-ctrl", "rpc"; + mboxes = <&mailbox 0 + &mailbox 1>; + }; diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt new file mode 100644 index 000000000000..d1a043339c11 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt @@ -0,0 +1,131 @@ +OMAP2+ Mailbox Driver +===================== + +The OMAP mailbox hardware facilitates communication between different processors +using a queued mailbox interrupt mechanism. The IP block is external to the +various processor subsystems and is connected on an interconnect bus. The +communication is achieved through a set of registers for message storage and +interrupt configuration registers. + +Each mailbox IP block has a certain number of h/w fifo queues and output +interrupt lines. An output interrupt line is routed to an interrupt controller +within a processor subsystem, and there can be more than one line going to a +specific processor's interrupt controller. The interrupt line connections are +fixed for an instance and are dictated by the IP integration into the SoC +(excluding the SoCs that have a Interrupt Crossbar IP). Each interrupt line is +programmable through a set of interrupt configuration registers, and have a rx +and tx interrupt source per h/w fifo. Communication between different processors +is achieved through the appropriate programming of the rx and tx interrupt +sources on the appropriate interrupt lines. + +The number of h/w fifo queues and interrupt lines dictate the usable registers. +All the current OMAP SoCs except for the newest DRA7xx SoC has a single IP +instance. DRA7xx has multiple instances with different number of h/w fifo queues +and interrupt lines between different instances. The interrupt lines can also be +routed to different processor sub-systems on DRA7xx as they are routed through +the Crossbar, a kind of interrupt router/multiplexer. + +Mailbox Device Node: +==================== +A Mailbox device node is used to represent a Mailbox IP instance within a SoC. +The sub-mailboxes are represented as child nodes of this parent node. + +Required properties: +-------------------- +- compatible: Should be one of the following, + "ti,omap2-mailbox" for OMAP2420, OMAP2430 SoCs + "ti,omap3-mailbox" for OMAP3430, OMAP3630 SoCs + "ti,omap4-mailbox" for OMAP44xx, OMAP54xx, AM33xx, + AM43xx and DRA7xx SoCs +- reg: Contains the mailbox register address range (base + address and length) +- interrupts: Contains the interrupt information for the mailbox + device. The format is dependent on which interrupt + controller the OMAP device uses +- ti,hwmods: Name of the hwmod associated with the mailbox +- #mbox-cells: Common mailbox binding property to identify the number + of cells required for the mailbox specifier. Should be + 1 +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox + device can interrupt +- ti,mbox-num-fifos: Number of h/w fifo queues within the mailbox IP block + +Child Nodes: +============ +A child node is used for representing the actual sub-mailbox device that is +used for the communication between the host processor and a remote processor. +Each child node should have a unique node name across all the different +mailbox device nodes. + +Required properties: +-------------------- +- ti,mbox-tx: sub-mailbox descriptor property defining a Tx fifo +- ti,mbox-rx: sub-mailbox descriptor property defining a Rx fifo + +Sub-mailbox Descriptor Data +--------------------------- +Each of the above ti,mbox-tx and ti,mbox-rx properties should have 3 cells of +data that represent the following: + Cell #1 (fifo_id) - mailbox fifo id used either for transmitting + (ti,mbox-tx) or for receiving (ti,mbox-rx) + Cell #2 (irq_id) - irq identifier index number to use from the parent's + interrupts data. Should be 0 for most of the cases, a + positive index value is seen only on mailboxes that have + multiple interrupt lines connected to the MPU processor. + Cell #3 (usr_id) - mailbox user id for identifying the interrupt line + associated with generating a tx/rx fifo interrupt. + +Mailbox Users: +============== +A device needing to communicate with a target processor device should specify +them using the common mailbox binding properties, "mboxes" and the optional +"mbox-names" (please see Documentation/devicetree/bindings/mailbox/mailbox.txt +for details). Each value of the mboxes property should contain a phandle to the +mailbox controller device node and an args specifier that will be the phandle to +the intended sub-mailbox child node to be used for communication. The equivalent +"mbox-names" property value can be used to give a name to the communication channel +to be used by the client user. + + +Example: +-------- + +/* OMAP4 */ +mailbox: mailbox@4a0f4000 { + compatible = "ti,omap4-mailbox"; + reg = <0x4a0f4000 0x200>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + #mbox-cells = <1>; + ti,mbox-num-users = <3>; + ti,mbox-num-fifos = <8>; + mbox_ipu: mbox_ipu { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <1 0 0>; + }; + mbox_dsp: mbox_dsp { + ti,mbox-tx = <3 0 0>; + ti,mbox-rx = <2 0 0>; + }; +}; + +dsp { + ... + mboxes = <&mailbox &mbox_dsp>; + ... +}; + +/* AM33xx */ +mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <77>; + ti,hwmods = "mailbox"; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + mbox_wkupm3: wkup_m3 { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <0 0 3>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt new file mode 100644 index 000000000000..fb5e7606643a --- /dev/null +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -0,0 +1,25 @@ +Device-Tree bindings for hix5hd2 ir IP + +Required properties: + - compatible: Should contain "hisilicon,hix5hd2-ir". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - clocks: clock phandle and specifier pair. + - hisilicon,power-syscon: phandle of syscon used to control power. + +Optional properties: + - linux,rc-map-name : Remote control map name. + +Example node: + + ir: ir@f8001000 { + compatible = "hisilicon,hix5hd2-ir"; + reg = <0xf8001000 0x1000>; + interrupts = <0 47 4>; + clocks = <&clock HIX5HD2_FIXED_24M>; + hisilicon,power-syscon = <&sysctrl>; + linux,rc-map-name = "rc-tivo"; + }; diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt new file mode 100644 index 000000000000..407848e85f31 --- /dev/null +++ b/Documentation/devicetree/bindings/media/meson-ir.txt @@ -0,0 +1,14 @@ +* Amlogic Meson IR remote control receiver + +Required properties: + - compatible : should be "amlogic,meson6-ir" + - reg : physical base address and length of the device registers + - interrupts : a single specifier for the interrupt from the device + +Example: + + ir-receiver@c8100480 { + compatible= "amlogic,meson6-ir"; + reg = <0xc8100480 0x20>; + interrupts = <0 15 1>; + }; diff --git a/Documentation/devicetree/bindings/media/si4713.txt b/Documentation/devicetree/bindings/media/si4713.txt new file mode 100644 index 000000000000..5ee5552d3465 --- /dev/null +++ b/Documentation/devicetree/bindings/media/si4713.txt @@ -0,0 +1,30 @@ +* Silicon Labs FM Radio transmitter + +The Silicon Labs Si4713 is an FM radio transmitter with receive power scan +supporting 76-108 MHz. It includes an RDS encoder and has both, a stereo-analog +and a digital interface, which supports I2S, left-justified and a custom +DSP-mode format. It is programmable through an I2C interface. + +Required Properties: +- compatible: Should contain "silabs,si4713" +- reg: the I2C address of the device + +Optional Properties: +- interrupts-extended: Interrupt specifier for the chips interrupt +- reset-gpios: GPIO specifier for the chips reset line +- vdd-supply: phandle for Vdd regulator +- vio-supply: phandle for Vio regulator + +Example: + +&i2c2 { + fmtx: si4713@63 { + compatible = "silabs,si4713"; + reg = <0x63>; + + interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */ + reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */ + vio-supply = <&vio>; + vdd-supply = <&vaux1>; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt new file mode 100644 index 000000000000..89657d1d4cd4 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt @@ -0,0 +1,21 @@ +Device Tree bindings for MVEBU SDRAM controllers + +The Marvell EBU SoCs all have a SDRAM controller. The SDRAM controller +differs from one SoC variant to another, but they also share a number +of commonalities. + +For now, this Device Tree binding documentation only documents the +Armada XP SDRAM controller. + +Required properties: + + - compatible: for Armada XP, "marvell,armada-xp-sdram-controller" + - reg: a resource specifier for the register space, which should + include all SDRAM controller registers as per the datasheet. + +Example: + +sdramc@1400 { + compatible = "marvell,armada-xp-sdram-controller"; + reg = <0x1400 0x500>; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt new file mode 100644 index 000000000000..f3db93c85eea --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt @@ -0,0 +1,36 @@ +NVIDIA Tegra Memory Controller device tree bindings +=================================================== + +Required properties: +- compatible: Should be "nvidia,tegra<chip>-mc" +- reg: Physical base address and length of the controller's registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mc: the module's clock input +- interrupts: The interrupt outputs from the controller. +- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines + the SWGROUP of the master. + +This device implements an IOMMU that complies with the generic IOMMU binding. +See ../iommu/iommu.txt for details. + +Example: +-------- + + mc: memory-controller@0,70019000 { + compatible = "nvidia,tegra124-mc"; + reg = <0x0 0x70019000 0x0 0x1000>; + clocks = <&tegra_car TEGRA124_CLK_MC>; + clock-names = "mc"; + + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + + #iommu-cells = <1>; + }; + + sdhci@0,700b0000 { + compatible = "nvidia,tegra124-sdhci"; + ... + iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/synopsys.txt b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt new file mode 100644 index 000000000000..f9c6454146b6 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt @@ -0,0 +1,11 @@ +Binding for Synopsys IntelliDDR Multi Protocol Memory Controller + +Required properties: + - compatible: Should be 'xlnx,zynq-ddrc-a05' + - reg: Base address and size of the controllers memory area + +Example: + memory-controller@f8006000 { + compatible = "xlnx,zynq-ddrc-a05"; + reg = <0xf8006000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 5c7e7230984a..7bd1273f571a 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -42,6 +42,13 @@ Optional properties: the chip default will be used. If present exactly five values must be specified. + - wlf,inmode : A list of INn_MODE register values, where n is the number + of input signals. Valid values are 0 (Differential), 1 (Single-ended) and + 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. + If present, values must be specified less than or equal to the number of + input singals. If values less than the number of input signals, elements + that has not been specifed are set to 0 by default. + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt new file mode 100644 index 000000000000..a28569540683 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt @@ -0,0 +1,15 @@ +* Device tree bindings for Atmel GPBR (General Purpose Backup Registers) + +The GPBR are a set of battery-backed registers. + +Required properties: +- compatible: "atmel,at91sam9260-gpbr", "syscon" +- reg: contains offset/length value of the GPBR memory + region. + +Example: + +gpbr: gpbr@fffffd50 { + compatible = "atmel,at91sam9260-gpbr", "syscon"; + reg = <0xfffffd50 0x10>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt new file mode 100644 index 000000000000..f64de95a8e8b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -0,0 +1,51 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver + +Required properties: + - compatible: value should be one of the following: + "atmel,sama5d3-hlcdc" + - reg: base address and size of the HLCDC device registers. + - clock-names: the name of the 3 clocks requested by the HLCDC device. + Should contain "periph_clk", "sys_clk" and "slow_clk". + - clocks: should contain the 3 clocks requested by the HLCDC device. + - interrupts: should contain the description of the HLCDC interrupt line + +The HLCDC IP exposes two subdevices: + - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt + - a Display Controller: see ../drm/atmel-hlcdc-dc.txt + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/hi6421.txt b/Documentation/devicetree/bindings/mfd/hi6421.txt new file mode 100644 index 000000000000..0d5a4466a494 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hi6421.txt @@ -0,0 +1,38 @@ +* HI6421 Multi-Functional Device (MFD), by HiSilicon Ltd. + +Required parent device properties: +- compatible : contains "hisilicon,hi6421-pmic"; +- reg : register range space of hi6421; + +Supported Hi6421 sub-devices include: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +regulators : None : None : Regulators + +Required child device properties: +None. + +Example: + hi6421 { + compatible = "hisilicon,hi6421-pmic"; + reg = <0xfcc00000 0x0180>; /* 0x60 << 2 */ + + regulators { + // supply for MLC NAND/ eMMC + hi6421_vout0_reg: hi6421_vout0 { + regulator-name = "VOUT0"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + // supply for 26M Oscillator + hi6421_vout1_reg: hi6421_vout1 { + regulator-name = "VOUT1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt new file mode 100644 index 000000000000..236264c10b92 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max14577.txt @@ -0,0 +1,146 @@ +Maxim MAX14577/77836 Multi-Function Device + +MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+ +Battery Charger and SFOUT LDO output for powering USB devices. It is +interfaced to host controller using I2C. + +MAX77836 additionally contains PMIC (with two LDO regulators) and Fuel Gauge. + + +Required properties: +- compatible : Must be "maxim,max14577" or "maxim,max77836". +- reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836) +- interrupts : IRQ line for the chip. +- interrupt-parent : The parent interrupt controller. + + +Required nodes: + - charger : + Node for configuring the charger driver. + Required properties: + - compatible : "maxim,max14577-charger" + or "maxim,max77836-charger" + - maxim,fast-charge-uamp : Current in uA for Fast Charge; + Valid values: + - for max14577: 90000 - 950000; + - for max77836: 45000 - 475000; + - maxim,eoc-uamp : Current in uA for End-Of-Charge mode; + Valid values: + - for max14577: 50000 - 200000; + - for max77836: 5000 - 100000; + - maxim,ovp-uvolt : OverVoltage Protection Threshold in uV; + In an overvoltage condition, INT asserts and charging + stops. Valid values: + - 6000000, 6500000, 7000000, 7500000; + - maxim,constant-uvolt : Battery Constant Voltage in uV; + Valid values: + - 4000000 - 4280000 (step by 20000); + - 4350000; + + +Optional nodes: +- max14577-muic/max77836-muic : + Node used only by extcon consumers. + Required properties: + - compatible : "maxim,max14577-muic" or "maxim,max77836-muic" + +- regulators : + Required properties: + - compatible : "maxim,max14577-regulator" + or "maxim,max77836-regulator" + + May contain a sub-node per regulator from the list below. Each + sub-node should contain the constraints and initialization information + for that regulator. See regulator.txt for a description of standard + properties for these sub-nodes. + + List of valid regulator names: + - for max14577: CHARGER, SAFEOUT. + - for max77836: CHARGER, SAFEOUT, LDO1, LDO2. + + The SAFEOUT is a fixed voltage regulator so there is no need to specify + voltages for it. + + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +max14577@25 { + compatible = "maxim,max14577"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max14577-muic { + compatible = "maxim,max14577-muic"; + }; + + regulators { + compatible = "maxim,max14577-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + }; + + charger { + compatible = "maxim,max14577-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <450000>; + maxim,eoc-uamp = <50000>; + maxim,ovp-uvolt = <6500000>; + }; +}; + + +max77836@25 { + compatible = "maxim,max77836"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max77836-muic { + compatible = "maxim,max77836-muic"; + }; + + regulators { + compatible = "maxim,max77836-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + }; + }; + + charger { + compatible = "maxim,max77836-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <225000>; + maxim,eoc-uamp = <7500>; + maxim,ovp-uvolt = <6500000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 678f3cf0b8f0..75fdfaf41831 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -34,6 +34,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : for BUCKs, where n can lie in range 1 to 9. example: BUCK1, BUCK5, BUCK9. + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + Example: max77686@09 { diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 11921cc417bf..01e9f30fe678 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -27,6 +27,20 @@ Optional properties: [*] refer Documentation/devicetree/bindings/regulator/regulator.txt +- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide + users with tactile feedback. PWM period and duty-cycle are varied in + order to provide the approprite level of feedback. + + Required properties: + - compatible : Must be "maxim,max77693-hpatic" + - haptic-supply : power supply for the haptic motor + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + - pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + To get more informations, please refer to documentaion. + [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + Example: max77693@66 { compatible = "maxim,max77693"; @@ -52,4 +66,11 @@ Example: regulator-boot-on; }; }; + + haptic { + compatible = "maxim,max77693-haptic"; + haptic-supply = <&haptic_supply>; + pwms = <&pwm 0 40000 0>; + pwm-names = "haptic"; + }; }; diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt new file mode 100644 index 000000000000..7182b8857f57 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt @@ -0,0 +1,64 @@ + Qualcomm SPMI PMICs multi-function device bindings + +The Qualcomm SPMI series presently includes PM8941, PM8841 and PMA8084 +PMICs. These PMICs use a QPNP scheme through SPMI interface. +QPNP is effectively a partitioning scheme for dividing the SPMI extended +register space up into logical pieces, and set of fixed register +locations/definitions within these regions, with some of these regions +specifically used for interrupt handling. + +The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are +interfaced to the chip via the SPMI (System Power Management Interface) bus. +Support for multiple independent functions are implemented by splitting the +16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes +each. A function can consume one or more of these fixed-size register regions. + +Required properties: +- compatible: Should contain one of: + "qcom,pm8941" + "qcom,pm8841" + "qcom,pma8084" + or generalized "qcom,spmi-pmic". +- reg: Specifies the SPMI USID slave address for this device. + For more information see: + Documentation/devicetree/bindings/spmi/spmi.txt + +Required properties for peripheral child nodes: +- compatible: Should contain "qcom,xxx", where "xxx" is a peripheral name. + +Optional properties for peripheral child nodes: +- interrupts: Interrupts are specified as a 4-tuple. For more information + see: + Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt +- interrupt-names: Corresponding interrupt name to the interrupts property + +Each child node of SPMI slave id represents a function of the PMIC. In the +example below the rtc device node represents a peripheral of pm8941 +SID = 0. The regulator device node represents a peripheral of pm8941 SID = 1. + +Example: + + spmi { + compatible = "qcom,spmi-pmic-arb"; + + pm8941@0 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + + rtc { + compatible = "qcom,rtc"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "alarm"; + }; + }; + + pm8941@1 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + + regulator { + compatible = "qcom,regulator"; + regulator-name = "8941_boost"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom,pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt index 03518dc8b6bd..f24f33409164 100644 --- a/Documentation/devicetree/bindings/mfd/qcom,pm8xxx.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -61,6 +61,7 @@ The below bindings specify the set of valid subnodes. Definition: must be one of: "qcom,pm8058-rtc" "qcom,pm8921-rtc" + "qcom,pm8941-rtc" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt new file mode 100644 index 000000000000..9e6e2592e5c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -0,0 +1,177 @@ +RK808 Power Management Integrated Circuit + +Required properties: +- compatible: "rockchip,rk808" +- reg: I2C slave address +- interrupt-parent: The parent interrupt controller. +- interrupts: the interrupt outputs of the controller. +- #clock-cells: from common clock binding; shall be set to 1 (multiple clock + outputs). See <dt-bindings/clock/rockchip,rk808.h> for clock IDs. + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name +- rockchip,system-power-controller: Telling whether or not this pmic is controlling + the system power. +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3 and LDO_REG7 +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for LDO_REG4 and LDO_REG5 +- vcc10-supply: The input supply for LDO_REG6 +- vcc11-supply: The input supply for LDO_REG8 +- vcc12-supply: The input supply for SWITCH_REG2 + +Regulators: All the regulators of RK808 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the RK808 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK808 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 8. + - SWITCH_REGn + - valid values for n are 1 to 2 + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details + +Example: + rk808: pmic@1b { + compatible = "rockchip,rk808"; + clock-output-names = "xin32k", "rk808-clkout2"; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + reg = <0x1b>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vccio_pmu>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd_arm"; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + }; + + vccio_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_pmu"; + }; + + vcc_tp: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt new file mode 100644 index 000000000000..937785a3eddc --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -0,0 +1,36 @@ +* Ricoh RN5T618 PMIC + +Ricoh RN5T618 is a power management IC which integrates 3 step-down +DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, +fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled +through a I2C interface. + +Required properties: + - compatible: should be "ricoh,rn5t618" + - reg: the I2C slave address of the device + +Sub-nodes: + - regulators: the node is required if the regulator functionality is + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, + LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + The common bindings for each individual regulator can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + + regulators { + DCDC1 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + DCDC2 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index ba2d7f0f9c5f..57a045016fca 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11, S2MPS14 and S2MPU02 Voltage and Current Regulator +* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,8 +7,8 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic" - or "samsung,s2mpu02-pmic". +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" + or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: @@ -17,8 +17,8 @@ Optional properties: - interrupts: Interrupt specifiers for interrupt sources. Optional nodes: -- clocks: s2mps11 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz - outputs, so to register these as clocks with common clock framework +- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 + KHz outputs, so to register these as clocks with common clock framework instantiate a sub-node named "clocks". It uses the common clock binding documented in : [Documentation/devicetree/bindings/clock/clock-bindings.txt] @@ -30,12 +30,12 @@ Optional nodes: the clock which they consume. Clock ID Devices ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS14, S5M8767 - 32KhzCP 1 S2MPS11, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS14, S5M8767 + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 - - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps14-clk", - "samsung,s5m8767-clk" + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -47,7 +47,7 @@ sub-node should be of the format as listed below. regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us - BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly + BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly regulator-ramp-delay = <0> can be used for them to disable ramp delay. In the absence of the regulator-ramp-delay property, the default ramp delay will be used. @@ -81,12 +81,14 @@ as per the datasheet of s2mps11. - LDOn - valid values for n are: - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 - S2MPS14: 1 to 25 - S2MPU02: 1 to 28 - Example: LDO1, LDO2, LDO28 - BUCKn - valid values for n are: - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 - S2MPS14: 1 to 5 - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index 56edb5520685..3fb68bfefc8b 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -13,6 +13,7 @@ Optional properties: - interrupt-parent : Specifies which IRQ controller we're connected to - wakeup-source : Marks the input device as wakable - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ Example: diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt index b9ee7b98d3e2..3d19963312ce 100644 --- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -23,8 +23,13 @@ down during off-idle. Note that this does not work on all boards depending on how the external oscillator is wired. Optional properties: -- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or - SLEEP-to-OFF transition when the system poweroffs. + +- ti,system-power-controller: This indicates that TWL4030 is the + power supply master of the system. With this flag, the chip will + initiate an ACTIVE-to-OFF or SLEEP-to-OFF transition when the + system poweroffs. + +- ti,use_poweroff: Deprecated name for ti,system-power-controller Example: &i2c1 { diff --git a/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt b/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt new file mode 100644 index 000000000000..d4e0141d3620 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/bcm3384-intc.txt @@ -0,0 +1,37 @@ +* Interrupt Controller + +Properties: +- compatible: "brcm,bcm3384-intc" + + Compatibility with BCM3384 and possibly other BCM33xx/BCM63xx SoCs. + +- reg: Address/length pairs for each mask/status register set. Length must + be 8. If multiple register sets are specified, the first set will + handle IRQ offsets 0..31, the second set 32..63, and so on. + +- interrupt-controller: This is an interrupt controller. + +- #interrupt-cells: Must be <1>. Just a simple IRQ offset; no level/edge + or polarity configuration is possible with this controller. + +- interrupt-parent: This controller is cascaded from a MIPS CPU HW IRQ, or + from another INTC. + +- interrupts: The IRQ on the parent controller. + +Example: + periph_intc: periph_intc@14e00038 { + compatible = "brcm,bcm3384-intc"; + + /* + * IRQs 0..31: mask reg 0x14e00038, status reg 0x14e0003c + * IRQs 32..63: mask reg 0x14e00340, status reg 0x14e00344 + */ + reg = <0x14e00038 0x8 0x14e00340 0x8>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <4>; + }; diff --git a/Documentation/devicetree/bindings/mips/brcm/bmips.txt b/Documentation/devicetree/bindings/mips/brcm/bmips.txt new file mode 100644 index 000000000000..8ef71b4085ca --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/bmips.txt @@ -0,0 +1,8 @@ +* Broadcom MIPS (BMIPS) CPUs + +Required properties: +- compatible: "brcm,bmips3300", "brcm,bmips4350", "brcm,bmips4380", + "brcm,bmips5000" + +- mips-hpt-frequency: This is common to all CPUs in the system so it lives + under the "cpus" node. diff --git a/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt b/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt new file mode 100644 index 000000000000..8a139cb3c0b5 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/cm-dsl.txt @@ -0,0 +1,11 @@ +* Broadcom cable/DSL platforms + +SoCs: + +Required properties: +- compatible: "brcm,bcm3384", "brcm,bcm33843" + +Boards: + +Required properties: +- compatible: "brcm,bcm93384wvg" diff --git a/Documentation/devicetree/bindings/mips/brcm/usb.txt b/Documentation/devicetree/bindings/mips/brcm/usb.txt new file mode 100644 index 000000000000..452c45c7bf29 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/usb.txt @@ -0,0 +1,11 @@ +* Broadcom USB controllers + +Required properties: +- compatible: "brcm,bcm3384-ohci", "brcm,bcm3384-ehci" + + These currently use the generic-ohci and generic-ehci drivers. On some + systems, special handling may be needed in the following cases: + + - Restoring state after systemwide power save modes + - Sharing PHYs with the USBD (UDC) hardware + - Figuring out which controllers are disabled on ASIC bondout variants diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt index 13aa4b62c62a..fc149f326dae 100644 --- a/Documentation/devicetree/bindings/mips/cpu_irq.txt +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -1,6 +1,6 @@ MIPS CPU interrupt controller -On MIPS the mips_cpu_intc_init() helper can be used to initialize the 8 CPU +On MIPS the mips_cpu_irq_of_init() helper can be used to initialize the 8 CPU IRQs from a devicetree file and create a irq_domain for IRQ controller. With the irq_domain in place we can describe how the 8 IRQs are wired to the @@ -36,7 +36,7 @@ Example devicetree: Example platform irq.c: static struct of_device_id __initdata of_irq_ids[] = { - { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_intc_init }, + { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_irq_of_init }, { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, {}, }; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 6cd3525d0e09..ee4fc0576c7d 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -18,6 +18,10 @@ Required Properties: specific extensions. - "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420 specific extensions. + - "samsung,exynos7-dw-mshc": for controllers with Samsung Exynos7 + specific extensions. + - "samsung,exynos7-dw-mshc-smu": for controllers with Samsung Exynos7 + specific extensions having an SMU. * samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface unit (ciu) clock. This property is applicable only for Exynos5 SoC's and diff --git a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt new file mode 100644 index 000000000000..85de99fcaa2f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt @@ -0,0 +1,29 @@ +* Imagination specific extensions to the Synopsys Designware Mobile Storage + Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Imagination specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "img,pistachio-dw-mshc": for Pistachio SoCs + +Example: + + mmc@18142000 { + compatible = "img,pistachio-dw-mshc"; + reg = <0x18142000 0x400>; + interrupts = <GIC_SHARED 39 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&system_clk>, <&sdhost_clk>; + clock-names = "biu", "ciu"; + + fifo-depth = <0x20>; + bus-width = <4>; + num-slots = <1>; + disable-wp; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 431716e37a39..b52628b18a53 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -40,6 +40,8 @@ Optional properties: - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported +- dsr: Value the card's (optional) Driver Stage Register (DSR) should be + programmed with. Valid range: [0 .. 0xffff]. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c559f3f36309..c327c2d6f23d 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -10,12 +10,14 @@ extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: * compatible: should be - - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following + - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, + before RK3288 + - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 Example: rkdwmmc0@12200000 { - compatible = "rockchip,rk2928-dw-mshc"; + compatible = "rockchip,rk3288-dw-mshc"; reg = <0x12200000 0x1000>; interrupts = <0 75 0>; #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt index 86223c3eda90..4dd6deb90719 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -12,6 +12,10 @@ Required properties: * for "marvell,armada-380-sdhci", two register areas. The first one for the SDHCI registers themselves, and the second one for the AXI/Mbus bridge registers of the SDHCI unit. +- clocks: Array of clocks required for SDHCI; requires at least one for + I/O clock. +- clock-names: Array of names corresponding to clocks property; shall be + "io" for I/O clock and "core" for optional core clock. Optional properties: - mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. @@ -23,6 +27,8 @@ sdhci@d4280800 { reg = <0xd4280800 0x800>; bus-width = <8>; interrupts = <27>; + clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>; + clock-names = "io", "core"; non-removable; mrvl,clk-delay-cycles = <31>; }; @@ -32,5 +38,6 @@ sdhci@d8000 { reg = <0xd8000 0x1000>, <0xdc000 0x100>; interrupts = <0 25 0x4>; clocks = <&gateclk 17>; + clock-names = "io"; mrvl,clk-delay-cycles = <0x1F>; }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index fa0f327cde01..400b640fabc7 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -19,6 +19,9 @@ Required properties: "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC "renesas,sdhi-r8a7791" - SDHI IP on R8A7791 SoC + "renesas,sdhi-r8a7792" - SDHI IP on R8A7792 SoC + "renesas,sdhi-r8a7793" - SDHI IP on R8A7793 SoC + "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index c4728839d0c1..1fe6dde98499 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -5,7 +5,9 @@ Required properties: - reg : should specify localbus address and size used for the chip, and hardware ECC controller if available. If the hardware ECC is PMECC, it should contain address and size for - PMECC, PMECC Error Location controller and ROM which has lookup tables. + PMECC and PMECC Error Location controller. + The PMECC lookup table address and size in ROM is optional. If not + specified, driver will build it in runtime. - atmel,nand-addr-offset : offset for the address latch. - atmel,nand-cmd-offset : offset for the command latch. - #address-cells, #size-cells : Must be present if the device has sub-nodes @@ -27,7 +29,7 @@ Optional properties: are: 512, 1024. - atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM for different sector size. First one is for sector size 512, the next is for - sector size 1024. + sector size 1024. If not specified, driver will build the table in runtime. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false - Nand Flash Controller(NFC) is a slave driver under Atmel nand flash @@ -36,6 +38,7 @@ Optional properties: - reg : should specify the address and size used for NFC command registers, NFC registers and NFC Sram. NFC Sram address and size can be absent if don't want to use it. + - clocks: phandle to the peripheral clock - Optional properties: - atmel,write-by-sram: boolean to enable NFC write by sram. @@ -98,6 +101,7 @@ nand0: nand@40000000 { compatible = "atmel,sama5d3-nfc"; #address-cells = <1>; #size-cells = <1>; + clocks = <&hsmc_clk> reg = < 0x70000000 0x10000000 /* NFC Command Registers */ 0xffffc000 0x00000070 /* NFC HSMC regs */ diff --git a/Documentation/devicetree/bindings/mtd/diskonchip.txt b/Documentation/devicetree/bindings/mtd/diskonchip.txt new file mode 100644 index 000000000000..3e13bfdbea5b --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/diskonchip.txt @@ -0,0 +1,15 @@ +M-Systems and Sandisk DiskOnChip devices + +M-System DiskOnChip G3 +====================== +The Sandisk (formerly M-Systems) docg3 is a nand device of 64M to 256MB. + +Required properties: + - compatible: should be "m-systems,diskonchip-g3" + - reg: register base and size + +Example: + docg3: flash@0 { + compatible = "m-systems,diskonchip-g3"; + reg = <0x0 0x2000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt index 36ef07d3c90f..af8915b41ccf 100644 --- a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt @@ -11,8 +11,8 @@ Required properties: are made in native endianness. - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions. -- gpios : specifies the gpio pins to control the NAND device. nwp is an - optional gpio and may be set to 0 if not present. +- gpios : Specifies the GPIO pins to control the NAND device. The order of + GPIO references is: RDY, nCE, ALE, CLE, and an optional nWP. Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -35,11 +35,11 @@ gpio-nand@1,0 { reg = <1 0x0000 0x2>; #address-cells = <1>; #size-cells = <1>; - gpios = <&banka 1 0 /* rdy */ - &banka 2 0 /* nce */ - &banka 3 0 /* ale */ - &banka 4 0 /* cle */ - 0 /* nwp */>; + gpios = <&banka 1 0>, /* RDY */ + <&banka 2 0>, /* nCE */ + <&banka 3 0>, /* ALE */ + <&banka 4 0>, /* CLE */ + <0>; /* nWP */ partition@0 { ... diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index ee654e95d8ad..fb733c4e1c11 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -110,8 +110,8 @@ on various other factors also like; Other factor which governs the selection of ecc-scheme is oob-size. Higher ECC schemes require more OOB/Spare area to store ECC syndrome, so the device should have enough free bytes available its OOB/Spare - area to accomodate ECC for entire page. In general following expression - helps in determining if given device can accomodate ECC syndrome: + area to accommodate ECC for entire page. In general following expression + helps in determining if given device can accommodate ECC syndrome: "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE" where OOBSIZE number of bytes in OOB/spare area @@ -133,5 +133,5 @@ on various other factors also like; Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and trying to use BCH16 (ECC_BYTES=26) ecc-scheme. Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B - which can be accomodate in the OOB/Spare area of this device + which can be accommodated in the OOB/Spare area of this device (OOBSIZE=128). So this device can use BCH16 ecc-scheme. diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 61c5ec850f2f..6b9f680cb579 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -4,8 +4,8 @@ Flash chips (Memory Technology Devices) are often used for solid state file systems on embedded devices. - compatible : should contain the specific model of mtd chip(s) - used, if known, followed by either "cfi-flash", "jedec-flash" - or "mtd-ram". + used, if known, followed by either "cfi-flash", "jedec-flash", + "mtd-ram" or "mtd-rom". - reg : Address range(s) of the mtd chip(s) It's possible to (optionally) define multiple "reg" tuples so that non-identical chips can be described in one node. diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt new file mode 100644 index 000000000000..0273adb8638c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -0,0 +1,45 @@ +Allwinner NAND Flash Controller (NFC) + +Required properties: +- compatible : "allwinner,sun4i-a10-nand". +- reg : shall contain registers location and length for data and reg. +- interrupts : shall define the nand controller interrupt. +- #address-cells: shall be set to 1. Encode the nand CS. +- #size-cells : shall be set to 0. +- clocks : shall reference nand controller clocks. +- clock-names : nand controller internal clock names. Shall contain : + * "ahb" : AHB gating clock + * "mod" : nand controller clock + +Optional children nodes: +Children nodes represent the available nand chips. + +Optional properties: +- allwinner,rb : shall contain the native Ready/Busy ids. + or +- rb-gpios : shall contain the gpios used as R/B pins. +- nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft", + "soft_bch" or "none") + +see Documentation/devicetree/mtd/nand.txt for generic bindings. + + +Examples: +nfc: nand@01c03000 { + compatible = "allwinner,sun4i-a10-nand"; + reg = <0x01c03000 0x1000>; + interrupts = <0 37 1>; + clocks = <&ahb_gates 13>, <&nand_clk>; + clock-names = "ahb", "mod"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>; + status = "okay"; + + nand@0 { + reg = <0>; + allwinner,rb = <0>; + nand-ecc-mode = "soft_bch"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt index 41354f730beb..26efd526d16c 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -7,7 +7,10 @@ Required properties: - PCS registers - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device -- interrupts: Should contain the amd-xgbe interrupt +- interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt + listed is required and is the general device interrupt. If the optional + amd,per-channel-interrupt property is specified, then one additional + interrupt for each DMA channel supported by the device should be specified - clocks: - DMA clock for the amd-xgbe device (used for calculating the correct Rx interrupt watchdog timer value on a DMA channel @@ -23,6 +26,9 @@ Optional properties: - mac-address: mac address to be assigned to the device. Can be overridden by UEFI. - dma-coherent: Present if dma operations are coherent +- amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate + a unique interrupt for each DMA channel - this requires an additional + interrupt be configured for each DMA channel Example: xgbe@e0700000 { @@ -30,7 +36,9 @@ Example: reg = <0 0xe0700000 0 0x80000>, <0 0xe0780000 0 0x80000>; interrupt-parent = <&gic>; - interrupts = <0 325 4>; + interrupts = <0 325 4>, + <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>; + amd,per-channel-interrupt; clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; clock-names = "dma_clk", "ptp_clk"; phy-handle = <&phy>; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index ebcad25efd0a..cfcc52705ed8 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -3,7 +3,7 @@ APM X-Gene SoC Ethernet nodes Ethernet nodes are defined to describe on-chip ethernet interfaces in APM X-Gene SoC. -Required properties: +Required properties for all the ethernet interfaces: - compatible: Should be "apm,xgene-enet" - reg: Address and length of the register set for the device. It contains the information of registers in the same order as described by reg-names @@ -15,6 +15,8 @@ Required properties: - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device - phy-connection-type: Interface type between ethernet device and PHY device + +Required properties for ethernet interfaces that have external PHY: - phy-handle: Reference to a PHY node connected to this device - mdio: Device tree subnode with the following required properties: diff --git a/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt new file mode 100644 index 000000000000..ab0bb4247d14 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt @@ -0,0 +1,39 @@ +* Broadcom UniMAC MDIO bus controller + +Required properties: +- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio" +- reg: address and length of the regsiter set for the device, first one is the + base register, and the second one is optional and for indirect accesses to + larger than 16-bits MDIO transactions +- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" +- #size-cells: must be 1 +- #address-cells: must be 0 + +Optional properties: +- interrupts: must be one if the interrupt is shared with the Ethernet MAC or + Ethernet switch this MDIO block is integrated from, or must be two, if there + are two separate interrupts, first one must be "mdio done" and second must be + for "mdio error" +- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed + to this hardware block, or must be "mdio_done" for the first interrupt and + "mdio_error" for the second when there are separate interrupts + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8 0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #size-cells = <1>; + #address-cells = <0>; + + ... + phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-sf2.txt b/Documentation/devicetree/bindings/net/broadcom-sf2.txt new file mode 100644 index 000000000000..30d487597ecb --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-sf2.txt @@ -0,0 +1,78 @@ +* Broadcom Starfighter 2 integrated swich + +Required properties: + +- compatible: should be "brcm,bcm7445-switch-v4.0" +- reg: addresses and length of the register sets for the device, must be 6 + pairs of register addresses and lengths +- interrupts: interrupts for the devices, must be two interrupts +- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt +- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt +- #size-cells: must be 0 +- #address-cells: must be 2, see dsa/dsa.txt + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. + +Optional properties: + +- reg-names: litteral names for the device base register addresses, when present + must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" + +- interrupt-names: litternal names for the device interrupt lines, when present + must be: "switch_0" and "switch_1" + +- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the + switch + +- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported + by the switch + +- brcm,fcb-pause-override: boolean property, if present indicates that the switch + supports Failover Control Block pause override capability + +- brcm,acb-packets-inflight: boolean property, if present indicates that the switch + Admission Control Block supports reporting the number of packets in-flight in a + switch queue + +Example: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; + #address-cells = <2>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ... + switch@0 { + reg = <0 0>; + #size-cells = <0>; + #address-cells <1>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt index 8f1ae81228e3..5a1d8b0c39e9 100644 --- a/Documentation/devicetree/bindings/net/can/c_can.txt +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -4,6 +4,8 @@ Bosch C_CAN/D_CAN controller Device Tree Bindings Required properties: - compatible : Should be "bosch,c_can" for C_CAN controllers and "bosch,d_can" for D_CAN controllers. + Can be "ti,dra7-d_can", "ti,am3352-d_can" or + "ti,am4372-d_can". - reg : physical base address and size of the C_CAN/D_CAN registers map - interrupts : property with a value describing the interrupt @@ -12,6 +14,9 @@ Required properties: Optional properties: - ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the instance number +- syscon-raminit : Handle to system control region that contains the + RAMINIT register, register offset to the RAMINIT + register and the CAN instance number (0 offset). Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt new file mode 100644 index 000000000000..9e331777c203 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/m_can.txt @@ -0,0 +1,67 @@ +Bosch MCAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,m_can" for M_CAN controllers +- reg : physical base address and size of the M_CAN + registers map and Message RAM +- reg-names : Should be "m_can" and "message_ram" +- interrupts : Should be the interrupt number of M_CAN interrupt + line 0 and line 1, could be same if sharing + the same interrupt. +- interrupt-names : Should contain "int0" and "int1" +- clocks : Clocks used by controller, should be host clock + and CAN clock. +- clock-names : Should contain "hclk" and "cclk" +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- bosch,mram-cfg : Message RAM configuration data. + Multiple M_CAN instances can share the same Message + RAM and each element(e.g Rx FIFO or Tx Buffer and etc) + number in Message RAM is also configurable, + so this property is telling driver how the shared or + private Message RAM are used by this M_CAN controller. + + The format should be as follows: + <offset sidf_elems xidf_elems rxf0_elems rxf1_elems + rxb_elems txe_elems txb_elems> + The 'offset' is an address offset of the Message RAM + where the following elements start from. This is + usually set to 0x0 if you're using a private Message + RAM. The remain cells are used to specify how many + elements are used for each FIFO/Buffer. + + M_CAN includes the following elements according to user manual: + 11-bit Filter 0-128 elements / 0-128 words + 29-bit Filter 0-64 elements / 0-128 words + Rx FIFO 0 0-64 elements / 0-1152 words + Rx FIFO 1 0-64 elements / 0-1152 words + Rx Buffers 0-64 elements / 0-1152 words + Tx Event FIFO 0-32 elements / 0-64 words + Tx Buffers 0-32 elements / 0-576 words + + Please refer to 2.4.1 Message RAM Configuration in + Bosch M_CAN user manual for details. + +Example: +SoC dtsi: +m_can1: can@020e8000 { + compatible = "bosch,m_can"; + reg = <0x020e8000 0x4000>, <0x02298000 0x4000>; + reg-names = "m_can", "message_ram"; + interrupts = <0 114 0x04>, + <0 114 0x04>; + interrupt-names = "int0", "int1"; + clocks = <&clks IMX6SX_CLK_CANFD>, + <&clks IMX6SX_CLK_CANFD>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>; + status = "disabled"; +}; + +Board dts: +&m_can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_m_can1>; + status = "enabled"; +}; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt new file mode 100644 index 000000000000..002d8440bf66 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -0,0 +1,43 @@ +Renesas R-Car CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. + "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. + "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. + "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. +- reg: physical base address and size of the R-Car CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Optional properties: +- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: + <0x0> (default) : Peripheral clock (clkp1) + <0x1> : Peripheral clock (clkp2) + <0x3> : Externally input clock + +Example +------- + +SoC common .dtsi file: + + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + +Board specific .dts file: + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index ae2b8b7f9c38..33fe8462edf4 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -24,15 +24,17 @@ Optional properties: - ti,hwmods : Must be "cpgmac0" - no_bd_ram : Must be 0 or 1 - dual_emac : Specifies Switch to act as Dual EMAC +- syscon : Phandle to the system control device node, which is + the control module device of the am33x Slave Properties: Required properties: - phy_id : Specifies slave phy id - phy-mode : See ethernet.txt file in the same directory -- mac-address : See ethernet.txt file in the same directory Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports +- mac-address : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. @@ -57,6 +59,7 @@ Examples: active_slave = <0>; cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; + syscon = <&cm>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; @@ -85,6 +88,7 @@ Examples: active_slave = <0>; cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; + syscon = <&cm>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 49f4f7ae3f51..e124847443f8 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -10,7 +10,7 @@ Required properties: - dsa,ethernet : Should be a phandle to a valid Ethernet device node - dsa,mii-bus : Should be a phandle to a valid MDIO bus device node -Optionnal properties: +Optional properties: - interrupts : property with a value describing the switch interrupt number (not supported by the driver) @@ -23,6 +23,13 @@ Each of these switch child nodes should have the following required properties: - #address-cells : Must be 1 - #size-cells : Must be 0 +A switch child node has the following optional property: + +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. + A switch may have multiple "port" children nodes Each port children node must have the following mandatory properties: @@ -39,6 +46,22 @@ Optionnal property: This property is only used when switches are being chained/cascaded together. +- phy-handle : Phandle to a PHY on an external MDIO bus, not the + switch internal one. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : String representing the connection to the designated + PHY node specified by the 'phy-handle' property. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +Optional subnodes: +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + Example: dsa@0 { @@ -58,6 +81,7 @@ Example: port@0 { reg = <0>; label = "lan1"; + phy-handle = <&phy0>; }; port@1 { diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt new file mode 100644 index 000000000000..8dc1c79fef7f --- /dev/null +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt @@ -0,0 +1,50 @@ +* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs + +Required properties: +- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac" + according to the target SoC. +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- rockchip,grf: phandle to the syscon grf used to control speed and mode + for emac. +- phy: see ethernet.txt file in the same directory. +- phy-mode: see ethernet.txt file in the same directory. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Clock handling: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "hclk" for the host clock needed to calculate and set + polling period of EMAC and "macref" for the reference clock needed to transfer + data to and from the phy. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + +ethernet@10204000 { + compatible = "rockchip,rk3188-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; + clock-names = "hclk", "macref"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; + + rockchip,grf = <&grf>; + + phy = <&phy0>; + phy-mode = "rmii"; + phy-supply = <&vcc_rmii>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 8a2c7b55ec16..0c8775c45798 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -16,6 +16,12 @@ Optional properties: - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. Use instead of phy-handle. +- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the tx queue number, otherwise set tx queue + number to 1. +- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the rx queue number, otherwise set rx queue + number to 1. Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes diff --git a/Documentation/devicetree/bindings/net/marvell-pxa168.txt b/Documentation/devicetree/bindings/net/marvell-pxa168.txt new file mode 100644 index 000000000000..845a148a346e --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pxa168.txt @@ -0,0 +1,36 @@ +* Marvell PXA168 Ethernet Controller + +Required properties: +- compatible: should be "marvell,pxa168-eth". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- clocks: pointer to the clock for the device. + +Optional properties: +- port-id: Ethernet port number. Should be '0','1' or '2'. +- #address-cells: must be 1 when using sub-nodes. +- #size-cells: must be 0 when using sub-nodes. +- phy-handle: see ethernet.txt file in the same directory. +- local-mac-address: see ethernet.txt file in the same directory. + +Sub-nodes: +Each PHY can be represented as a sub-node. This is not mandatory. + +Sub-nodes required properties: +- reg: the MDIO address of the PHY. + +Example: + + eth0: ethernet@f7b90000 { + compatible = "marvell,pxa168-eth"; + reg = <0xf7b90000 0x10000>; + clocks = <&chip CLKID_GETH0>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + phy-handle = <ðphy0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt new file mode 100644 index 000000000000..ec633d74a8a8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -0,0 +1,25 @@ +* Amlogic Meson DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file net/stmmac.txt with the following changes. + +Required properties: + +- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac" + and any applicable more detailed version number + described in net/stmmac.txt + +- reg: should contain a register range for the dwmac controller and + another one for the Amlogic specific configuration + +Example: + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + } diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt index 98a3e61f9ee8..87496a8c64ab 100644 --- a/Documentation/devicetree/bindings/net/micrel.txt +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -6,13 +6,32 @@ Optional properties: - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs. - Configure the LED mode with single value. The list of PHYs and - the bits that are currently supported: + Configure the LED mode with single value. The list of PHYs and the + bits that are currently supported: - KSZ8001: register 0x1e, bits 15..14 - KSZ8041: register 0x1e, bits 15..14 - KSZ8021: register 0x1f, bits 5..4 - KSZ8031: register 0x1f, bits 5..4 - KSZ8051: register 0x1f, bits 5..4 + KSZ8001: register 0x1e, bits 15..14 + KSZ8041: register 0x1e, bits 15..14 + KSZ8021: register 0x1f, bits 5..4 + KSZ8031: register 0x1f, bits 5..4 + KSZ8051: register 0x1f, bits 5..4 + KSZ8081: register 0x1f, bits 5..4 + KSZ8091: register 0x1f, bits 5..4 - See the respective PHY datasheet for the mode values. + See the respective PHY datasheet for the mode values. + + - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select + bit selects 25 MHz mode + + Setting the RMII Reference Clock Select bit enables 25 MHz rather + than 50 MHz clock mode. + + Note that this option in only needed for certain PHY revisions with a + non-standard, inverted function of this configuration bit. + Specifically, a clock reference ("rmii-ref" below) is always needed to + actually select a mode. + + - clocks, clock-names: contains clocks according to the common clock bindings. + + supported clocks: + - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference + input clock. Used to determine the XI input clock. diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt index 3b58ae480344..9005608cbbd1 100644 --- a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt +++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt @@ -26,7 +26,7 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): clock-frequency = <400000>; interrupt-parent = <&gpio5>; - interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt index 1e436133685f..7c89ca290ced 100644 --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -13,6 +13,11 @@ Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. - autosuspend-delay: Specify autosuspend delay in milliseconds. +- vin-voltage-override: Specify voltage of VIN pin in microvolts. +- irq-status-read-quirk: Specify that the trf7970a being used has the + "IRQ Status Read" erratum. +- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" + erratum. Example (for ARM-based BeagleBone with TRF7970A on SPI1): @@ -30,7 +35,10 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1): ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>, <&gpio2 5 GPIO_ACTIVE_LOW>; vin-supply = <&ldo3_reg>; + vin-voltage-override = <5000000>; autosuspend-delay = <30000>; + irq-status-read-quirk; + en2-rf-quirk; status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 5b8c58903077..40831fbaff72 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -19,7 +19,6 @@ Optional Properties: specifications. If neither of these are specified, the default is to assume clause 22. The compatible list may also contain other elements. -- max-speed: Maximum PHY supported speed (10, 100, 1000...) If the phy's identifier is known then the list may contain an entry of the form: "ethernet-phy-idAAAA.BBBB" where @@ -29,6 +28,8 @@ Optional Properties: 4 hex digits. This is the chip vendor OUI bits 19:24, followed by 10 bits of a vendor specific ID. +- max-speed: Maximum PHY supported speed (10, 100, 1000...) + Example: ethernet-phy@0 { diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt new file mode 100644 index 000000000000..c74989c0d8ac --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt @@ -0,0 +1,47 @@ +* Qualcomm QCA7000 (Ethernet over SPI protocol) + +Note: The QCA7000 is useable as a SPI device. In this case it must be defined +as a child of a SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source interrupt + and the second cell should specify the trigger type as rising edge +- spi-cpha : Must be set +- spi-cpol: Must be set + +Optional properties: +- interrupt-parent : Specify the pHandle of the source interrupt +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing + the property will set the SPI frequency to 8000000 Hertz. +- local-mac-address: 6 bytes, MAC address +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select between each data + word. In burst mode these gaps aren't necessary, which is faster. + This setting depends on how the QCA7000 is setup via GPIO pin strapping. + If the property is missing the driver defaults to burst mode. + +Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt index 989f6c95cfd5..888c250197fe 100644 --- a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt @@ -17,7 +17,7 @@ Required properties: - samsung,pbl: Integer, Programmable Burst Length. Supported values are 1, 2, 4, 8, 16, or 32. - samsung,burst-map: Integer, Program the possible bursts supported by sxgbe - This is an interger and represents allowable DMA bursts when fixed burst. + This is an integer and represents allowable DMA bursts when fixed burst. Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled. When fixed length is needed for burst mode, it can be set within allowable range. diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 34d4db1a4e25..2f6ec85fda8e 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -9,6 +9,7 @@ Required properties: "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. - reg: offset and length of (1) the E-DMAC/feLic register block (required), diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index 0f8487b88822..e77e167593db 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -11,3 +11,5 @@ Optional properties: are supported on the device. Valid value for SMSC LAN91c111 are 1, 2 or 4. If it's omitted or invalid, the size would be 2 meaning 16-bit access only. +- power-gpios: GPIO to control the PWRDWN pin +- reset-gpios: GPIO to control the RESET pin diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 2a60cd3e8d5d..3a9d67951606 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -12,6 +12,10 @@ Required properties: - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. +Optional properties: +altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if + DWMAC controller is connected emac splitter. + Example: gmac0: ethernet@ff700000 { diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt index 3dd3d0bf112f..6762a6b5da7e 100644 --- a/Documentation/devicetree/bindings/net/sti-dwmac.txt +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -1,58 +1,65 @@ STMicroelectronics SoC DWMAC glue layer controller +This file documents differences between the core properties in +Documentation/devicetree/bindings/net/stmmac.txt +and what is needed on STi platforms to program the stmmac glue logic. + The device node has following properties. Required properties: - - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or - "st,stid127-dwmac". - - reg : Offset of the glue configuration register map in system + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", + "st,stih407-dwmac", "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system configuration regmap pointed by st,syscon property and size. - - - reg-names : Should be "sti-ethconf". - - - st,syscon : Should be phandle to system configuration node which + - st,syscon : Should be phandle to system configuration node which encompases this glue registers. + - st,gmac_en: this is to enable the gmac into a dedicated sysctl control + register available on STiH407 SoC. + - sti-ethconf: this is the gmac glue logic register to enable the GMAC, + select among the different modes and program the clk retiming. + - pinctrl-0: pin-control for all the MII mode supported. - - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be - wired up in from different sources. One via TXCLK pin and other via CLK_125 - pin. This wiring is totally board dependent. However the retiming glue - logic should be configured accordingly. Possible values for this property - - "txclk" - if 125Mhz clock is wired up via txclk line. - "clk_125" - if 125Mhz clock is wired up via clk_125 line. - - This property is only valid for Giga bit setup( GMII, RGMII), and it is - un-used for non-giga bit (MII and RMII) setups. Also note that internal - clockgen can not generate stable 125Mhz clock. - - - st,ext-phyclk: This boolean property indicates who is generating the clock - for tx and rx. This property is only valid for RMII case where the clock can - be generated from the MAC or PHY. - - - clock-names: should be "sti-ethclk". - - clocks: Should point to ethernet clockgen which can generate phyclk. - +Optional properties: + - resets : phandle pointing to the system reset controller with correct + reset line index for ethernet reset. + - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or + MAC can generate it. + - st,tx-retime-src: This specifies which clk is wired up to the mac for + retimeing tx lines. This is totally board dependent and can take one of the + posssible values from "txclk", "clk_125" or "clkgen". + If not passed, the internal clock will be used by default. + - sti-ethclk: this is the phy clock. + - sti-clkconf: this is an extra sysconfig register, available in new SoCs, + to program the clk retiming. + - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g. + STiH407. Example: -ethernet0: dwmac@fe810000 { - device_type = "network"; - compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; - reg = <0xfe810000 0x8000>, <0x8bc 0x4>; - reg-names = "stmmaceth", "sti-ethconf"; - interrupts = <0 133 0>, <0 134 0>, <0 135 0>; - interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; - phy-mode = "mii"; +ethernet0: dwmac@9630000 { + device_type = "network"; + status = "disabled"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>, <0x80 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; - st,syscon = <&syscfg_rear>; + st,syscon = <&syscfg_sbc_reg>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; - snps,pbl = <32>; + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + <GIC_SPI 100 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; snps,mixed-burst; - resets = <&softreset STIH416_ETH0_SOFTRESET>; - reset-names = "stmmaceth"; - pinctrl-0 = <&pinctrl_mii0>; - pinctrl-names = "default"; - clocks = <&CLK_S_GMAC0_PHY>; - clock-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>, + <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>; }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index e45ac3f926b1..c41afd963edf 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -58,5 +58,5 @@ Examples: snps,multicast-filter-bins = <256>; snps,perfect-filter-entries = <128>; clocks = <&clock>; - clock-names = "stmmaceth">; + clock-names = "stmmaceth"; }; diff --git a/Documentation/devicetree/bindings/nios2/nios2.txt b/Documentation/devicetree/bindings/nios2/nios2.txt new file mode 100644 index 000000000000..d6d0a94cb3bb --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/nios2.txt @@ -0,0 +1,62 @@ +* Nios II Processor Binding + +This binding specifies what properties available in the device tree +representation of a Nios II Processor Core. + +Users can use sopc2dts tool for generating device tree sources (dts) from a +Qsys system. See more detail in: http://www.alterawiki.com/wiki/Sopc2dts + +Required properties: + +- compatible: Compatible property value should be "altr,nios2-1.0". +- reg: Contains CPU index. +- interrupt-controller: Specifies that the node is an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source, should be 1. +- clock-frequency: Contains the clock frequency for CPU, in Hz. +- dcache-line-size: Contains data cache line size. +- icache-line-size: Contains instruction line size. +- dcache-size: Contains data cache size. +- icache-size: Contains instruction cache size. +- altr,pid-num-bits: Specifies the number of bits to use to represent the process + identifier (PID). +- altr,tlb-num-ways: Specifies the number of set-associativity ways in the TLB. +- altr,tlb-num-entries: Specifies the number of entries in the TLB. +- altr,tlb-ptr-sz: Specifies size of TLB pointer. +- altr,has-mul: Specifies CPU hardware multipy support, should be 1. +- altr,has-mmu: Specifies CPU support MMU support, should be 1. +- altr,has-initda: Specifies CPU support initda instruction, should be 1. +- altr,reset-addr: Specifies CPU reset address +- altr,fast-tlb-miss-addr: Specifies CPU fast TLB miss exception address +- altr,exception-addr: Specifies CPU exception address + +Optional properties: +- altr,has-div: Specifies CPU hardware divide support +- altr,implementation: Nios II core implementation, this should be "fast"; + +Example: + +cpu@0x0 { + device_type = "cpu"; + compatible = "altr,nios2-1.0"; + reg = <0>; + interrupt-controller; + #interrupt-cells = <1>; + clock-frequency = <125000000>; + dcache-line-size = <32>; + icache-line-size = <32>; + dcache-size = <32768>; + icache-size = <32768>; + altr,implementation = "fast"; + altr,pid-num-bits = <8>; + altr,tlb-num-ways = <16>; + altr,tlb-num-entries = <128>; + altr,tlb-ptr-sz = <7>; + altr,has-div = <1>; + altr,has-mul = <1>; + altr,reset-addr = <0xc2800000>; + altr,fast-tlb-miss-addr = <0xc7fff400>; + altr,exception-addr = <0xd0000020>; + altr,has-initda = <1>; + altr,has-mmu = <1>; +}; diff --git a/Documentation/devicetree/bindings/nios2/timer.txt b/Documentation/devicetree/bindings/nios2/timer.txt new file mode 100644 index 000000000000..904a5846d7ac --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/timer.txt @@ -0,0 +1,19 @@ +Altera Timer + +Required properties: + +- compatible : should be "altr,timer-1.0" +- reg : Specifies base physical address and size of the registers. +- interrupt-parent: phandle of the interrupt controller +- interrupts : Should contain the timer interrupt number +- clock-frequency : The frequency of the clock that drives the counter, in Hz. + +Example: + +timer { + compatible = "altr,timer-1.0"; + reg = <0x00400000 0x00000020>; + interrupt-parent = <&cpu>; + interrupts = <11>; + clock-frequency = <125000000>; +}; diff --git a/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt b/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt new file mode 100644 index 000000000000..889d511d66c9 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101xtn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/auo,b116xw03.txt b/Documentation/devicetree/bindings/panel/auo,b116xw03.txt new file mode 100644 index 000000000000..690d0a568ef3 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b116xw03.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 11.6" HD (1366x768) color TFT-LCD panel + +Required properties: +- compatible: should be "auo,b116xw03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/hannstar,hsd070pww1.txt b/Documentation/devicetree/bindings/panel/hannstar,hsd070pww1.txt new file mode 100644 index 000000000000..7da1d5c038ff --- /dev/null +++ b/Documentation/devicetree/bindings/panel/hannstar,hsd070pww1.txt @@ -0,0 +1,7 @@ +HannStar Display Corp. HSD070PWW1 7.0" WXGA TFT LCD panel + +Required properties: +- compatible: should be "hannstar,hsd070pww1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/hit,tx23d38vm0caa.txt b/Documentation/devicetree/bindings/panel/hit,tx23d38vm0caa.txt new file mode 100644 index 000000000000..04caaae19af6 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/hit,tx23d38vm0caa.txt @@ -0,0 +1,7 @@ +Hitachi Ltd. Corporation 9" WVGA (800x480) TFT LCD panel + +Required properties: +- compatible: should be "hit,tx23d38vm0caa" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/innolux,g121i1-l01.txt b/Documentation/devicetree/bindings/panel/innolux,g121i1-l01.txt new file mode 100644 index 000000000000..2743b07cd2f2 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/innolux,g121i1-l01.txt @@ -0,0 +1,7 @@ +Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel + +Required properties: +- compatible: should be "innolux,g121i1-l01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt b/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt new file mode 100644 index 000000000000..f522bb8e47e1 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt @@ -0,0 +1,49 @@ +Sharp Microelectronics 10.1" WQXGA TFT LCD panel + +This panel requires a dual-channel DSI host to operate. It supports two modes: +- left-right: each channel drives the left or right half of the screen +- even-odd: each channel drives the even or odd lines of the screen + +Each of the DSI channels controls a separate DSI peripheral. The peripheral +driven by the first link (DSI-LINK1), left or even, is considered the primary +peripheral and controls the device. The 'link2' property contains a phandle +to the peripheral driven by the second link (DSI-LINK2, right or odd). + +Note that in video mode the DSI-LINK1 interface always provides the left/even +pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it +is possible to program either link to drive the left/even or right/odd pixels +but for the sake of consistency this binding assumes that the same assignment +is chosen as for video mode. + +Required properties: +- compatible: should be "sharp,lq101r1sx01" +- reg: DSI virtual channel of the peripheral + +Required properties (for DSI-LINK1 only): +- link2: phandle to the DSI peripheral on the secondary link. Note that the + presence of this property marks the containing node as DSI-LINK1. +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties (for DSI-LINK1 only): +- backlight: phandle of the backlight device attached to the panel + +Example: + + dsi@54300000 { + panel: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + + link2 = <&secondary>; + + power-supply = <...>; + backlight = <...>; + }; + }; + + dsi@54400000 { + secondary: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index ed0d9b9fff2b..9f4faa8e8d00 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -23,3 +23,6 @@ Required properties: Optional properties: - reset-gpio: gpio pin number of power good signal +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to + specify this property, to keep backwards compatibility a range of 0x00-0xff + is assumed if not present) diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 9455fd0ec830..6fbba53a309b 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -17,7 +17,9 @@ Example: pcie@0x01000000 { compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; - reg = <0x01ffc000 0x4000>; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; diff --git a/Documentation/devicetree/bindings/pci/fsl,pci.txt b/Documentation/devicetree/bindings/pci/fsl,pci.txt new file mode 100644 index 000000000000..d8ac4a768e7e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,pci.txt @@ -0,0 +1,27 @@ +* Bus Enumeration by Freescale PCI-X Agent + +Typically any Freescale PCI-X bridge hardware strapped into Agent mode +is prevented from enumerating the bus. The PrPMC form-factor requires +all mezzanines to be PCI-X Agents, but one per system may still +enumerate the bus. + +The property defined below will allow a PCI-X bridge to be used for bus +enumeration despite being strapped into Agent mode. + +Required properties: +- fsl,pci-agent-force-enum : There is no value associated with this + property. The property itself is treated as a boolean. + +Example: + + /* PCI-X bridge known to be PrPMC Monarch */ + pci0: pci@ef008000 { + fsl,pci-agent-force-enum; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci"; + device_type = "pci"; + ... + ... + }; diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt index f0b0436807b4..cf3e205e0b7e 100644 --- a/Documentation/devicetree/bindings/pci/host-generic-pci.txt +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -55,7 +55,7 @@ For CAM, this 24-bit offset is: cfg_offset(bus, device, function, register) = bus << 16 | device << 11 | function << 8 | register -Whilst ECAM extends this by 4 bits to accomodate 4k of function space: +Whilst ECAM extends this by 4 bits to accommodate 4k of function space: cfg_offset(bus, device, function, register) = bus << 20 | device << 15 | function << 12 | register diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt new file mode 100644 index 000000000000..6286f049bf18 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -0,0 +1,42 @@ +Freescale Layerscape PCIe controller + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: should contain the platform identifier such as "fsl,ls1021a-pcie" +- reg: base addresses and lengths of the PCIe controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The interrupt that is asserted for controller interrupts +- fsl,pcie-scfg: Must include two entries. + The first entry must be a link to the SCFG device node + The second entry must be '0' or '1' based on physical PCIe controller index. + This is used to get SCFG PEXN registers + +Example: + + pcie@3400000 { + compatible = "fsl,ls1021a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x00010000 /* controller registers */ + 0x40 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ + interrupt-names = "intr"; + fsl,pcie-scfg = <&scfg 0>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0xc2000000 0x0 0x20000000 0x40 0x20000000 0x0 0x20000000 /* prefetchable memory */ + 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 2 &gic GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 3 &gic GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 4 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 0823362548dc..d763e047c6ae 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -1,7 +1,10 @@ NVIDIA Tegra PCIe controller Required properties: -- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie" +- compatible: Must be one of: + - "nvidia,tegra20-pcie" + - "nvidia,tegra30-pcie" + - "nvidia,tegra124-pcie" - device_type: Must be "pci" - reg: A list of physical base address and length for each set of controller registers. Must contain an entry for each entry in the reg-names property. @@ -57,6 +60,11 @@ Required properties: - afi - pcie_x +Required properties on Tegra124 and later: +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -84,6 +92,21 @@ Power supplies for Tegra30: - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 000000000000..54eae2938174 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,63 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on Designware PCI h/w version 3.65. +It shares common functions with PCIe Designware core driver and inherit +common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +for the details of Designware DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to Generic Keystone SerDes phy for PCI + phy-names: name of the Generic Keystine SerDes phy for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + +Designware DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 41aeed38926d..f8fbe9af7b2f 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -7,3 +7,14 @@ And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt new file mode 100644 index 000000000000..1070b068c7c6 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -0,0 +1,57 @@ +* AppliedMicro X-Gene PCIe interface + +Required properties: +- device_type: set to "pci" +- compatible: should contain "apm,xgene-pcie" to identify the core. +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "csr": controller configuration registers. + "cfg": pcie configuration space registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- ranges: ranges for the outbound memory, I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if dma operations are coherent + +Example: + +SoC specific DT Entry: + + pcie0: pcie@1f2b0000 { + status = "disabled"; + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + }; + + +Board specific DT Entry: + &pcie0 { + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt new file mode 100644 index 000000000000..3e2c88d97ad4 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -0,0 +1,62 @@ +* Xilinx AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a" +- reg: Should contain AXI PCIe registers location and length +- device_type: must be "pci" +- interrupts: Should contain AXI PCIe interrupt +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + +Optional properties: +- bus-range: PCI bus numbers covered + +Interrupt controller child node ++++++++++++++++++++++++++++++++ +Required properties: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +NOTE: +The core provides a single interrupt for both INTx/MSI messages. So, +created a interrupt controller node to support 'interrupt-map' DT +functionality. The driver will create an IRQ domain for this map, decode +the four INTx interrupts in ISR and route them to this domain. + + +Example: +++++++++ + + pci_express: axi-pcie@50000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = < 0x50000000 0x10000000 >; + device_type = "pci"; + interrupts = < 0 52 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + } + }; diff --git a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt index 88f8c23384c0..c0155f842f62 100644 --- a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt @@ -2,7 +2,9 @@ Berlin SATA PHY --------------- Required properties: -- compatible: should be "marvell,berlin2q-sata-phy" +- compatible: should be one of + "marvell,berlin2-sata-phy" + "marvell,berlin2q-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - phy-cells: from the generic PHY bindings, must be 1 diff --git a/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt new file mode 100644 index 000000000000..be33780f668e --- /dev/null +++ b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt @@ -0,0 +1,16 @@ +* Marvell Berlin USB PHY + +Required properties: +- compatible: "marvell,berlin2-usb-phy" or "marvell,berlin2cd-usb-phy" +- reg: base address and length of the registers +- #phys-cells: should be 0 +- resets: reference to the reset controller + +Example: + + usb-phy@f774000 { + compatible = "marvell,berlin2-usb-phy"; + reg = <0xf774000 0x128>; + #phy-cells = <0>; + resets = <&chip 0x104 14>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index 2aa1840200ed..1293c321754c 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -27,7 +27,7 @@ phys: phy { }; That node describes an IP block (PHY provider) that implements 2 different PHYs. -In order to differentiate between these 2 PHYs, an additonal specifier should be +In order to differentiate between these 2 PHYs, an additional specifier should be given while trying to get a reference to it. PHY user node diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt new file mode 100644 index 000000000000..46a135dae6b3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt @@ -0,0 +1,128 @@ +STMicroelectronics STi MIPHY28LP PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA, PCIe or USB3. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy28lp-phy". +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe or USB3 mode setting bits. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI + - PHY_TYPE_USB3 +- reg : Address and length of the register set for the device. +- reg-names : The names of the register addresses corresponding to the registers + filled in "reg". It can also contain the offset of the system configuration + registers used as glue-logic to setup the device for SATA/PCIe or USB3 + devices. +- resets : phandle to the parent reset controller. +- reset-names : Associated name must be "miphy-sw-rst". + +Optional properties (port (child) node): +- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This + is not available in all the MiPHY. For example, for STiH407, only the + MiPHY0 has this bit. +- st,osc-force-ext : to select the external oscillator. This can change from + different MiPHY inside the same SoC. +- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config + register. +- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive + line). +- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe). +- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values. + +example: + + miphy28lp_phy: miphy28lp@9b22000 { + compatible = "st,miphy28lp-phy"; + st,syscfg = <&syscfg_core>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@9b22000 { + reg = <0x9b22000 0xff>, + <0x9b09000 0xff>, + <0x9b04000 0xff>, + <0x114 0x4>, /* sysctrl MiPHY cntrl */ + <0x818 0x4>, /* sysctrl MiPHY status*/ + <0xe0 0x4>, /* sysctrl PCIe */ + <0xec 0x4>; /* sysctrl SATA */ + reg-names = "sata-up", + "pcie-up", + "pipew", + "miphy-ctrl-glue", + "miphy-status-glue", + "pcie-glue", + "sata-glue"; + #phy-cells = <1>; + st,osc-rdy; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY0_SOFTRESET>; + }; + + phy_port1: port@9b2a000 { + reg = <0x9b2a000 0xff>, + <0x9b19000 0xff>, + <0x9b14000 0xff>, + <0x118 0x4>, + <0x81c 0x4>, + <0xe4 0x4>, + <0xf0 0x4>; + reg-names = "sata-up", + "pcie-up", + "pipew", + "miphy-ctrl-glue", + "miphy-status-glue", + "pcie-glue", + "sata-glue"; + #phy-cells = <1>; + st,osc-force-ext; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY1_SOFTRESET>; + }; + + phy_port2: port@8f95000 { + reg = <0x8f95000 0xff>, + <0x8f90000 0xff>, + <0x11c 0x4>, + <0x820 0x4>; + reg-names = "pipew", + "usb3-up", + "miphy-ctrl-glue", + "miphy-status-glue"; + #phy-cells = <1>; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY2_SOFTRESET>; + }; + }; + + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the miphy device node and an index +specifying which configuration to use, as described in phy-bindings.txt. + +example: + sata0: sata@9b20000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; + +Macro definitions for the supported miphy configuration can be found in: + +include/dt-bindings/phy/phy-miphy28lp.h diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu.txt b/Documentation/devicetree/bindings/phy/phy-mvebu.txt new file mode 100644 index 000000000000..f95b6260a3b3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mvebu.txt @@ -0,0 +1,43 @@ +* Marvell MVEBU SATA PHY + +Power control for the SATA phy found on Marvell MVEBU SoCs. + +This document extends the binding described in phy-bindings.txt + +Required properties : + + - reg : Offset and length of the register set for the SATA device + - compatible : Should be "marvell,mvebu-sata-phy" + - clocks : phandle of clock and specifier that supplies the device + - clock-names : Should be "sata" + +Example: + sata-phy@84000 { + compatible = "marvell,mvebu-sata-phy"; + reg = <0x84000 0x0334>; + clocks = <&gate_clk 15>; + clock-names = "sata"; + #phy-cells = <0>; + status = "ok"; + }; + +Armada 375 USB cluster +---------------------- + +Armada 375 comes with an USB2 host and device controller and an USB3 +controller. The USB cluster control register allows to manage common +features of both USB controllers. + +Required properties: + +- compatible: "marvell,armada-375-usb-cluster" +- reg: Should contain usb cluster register location and length. +- #phy-cells : from the generic phy bindings, must be 1. Possible +values are 1 (USB2), 2 (USB3). + +Example: + usbcluster: usb-cluster@18400 { + compatible = "marvell,armada-375-usb-cluster"; + reg = <0x18400 0x4>; + #phy-cells = <1> + }; diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt new file mode 100644 index 000000000000..1ef8228db73b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,30 @@ +ST STiH407 USB PHY controller + +This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3 +host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- reg : contain the offset and length of the system configuration registers + used as glue logic to control & parameter phy +- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg" +- st,syscfg : sysconfig register to manage phy parameter at driver level +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@f8 { + compatible = "st,stih407-usb2-phy"; + reg = <0xf8 0x04>, /* syscfg 5062 */ + <0xf4 0x04>; /* syscfg 5061 */ + reg-names = "param", "ctrl"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", "port"; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt new file mode 100644 index 000000000000..00944a05ee6b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt @@ -0,0 +1,24 @@ +STMicroelectronics STiH41x USB PHY binding +------------------------------------------ + +This file contains documentation for the usb phy found in STiH415/6 SoCs from +STMicroelectronics. + +Required properties: +- compatible : should be "st,stih416-usb-phy" or "st,stih415-usb-phy" +- st,syscfg : should be a phandle of the syscfg node +- clock-names : must contain "osc_phy" +- clocks : must contain an entry for each name in clock-names. +See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- #phy-cells : must be 0 for this phy +See: Documentation/devicetree/bindings/phy/phy-bindings.txt + +Example: + +usb2_phy: usb2phy@0 { + compatible = "st,stih416-usb-phy"; + #phy-cell = <0>; + st,syscfg = <&syscfg_rear>; + clocks = <&clk_sysin>; + clock-names = "osc_phy"; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt new file mode 100644 index 000000000000..86f2dbe07ed4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt @@ -0,0 +1,39 @@ +Qualcomm DWC3 HS AND SS PHY CONTROLLER +-------------------------------------- + +DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer +controllers. Each DWC3 PHY controller should have its own node. + +Required properties: +- compatible: should contain one of the following: + - "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller + - "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller +- reg: offset and length of the DWC3 PHY controller register set +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: Should contain "ref" for the PHY reference clock + +Optional clocks: + "xo" External reference clock + +Example: + phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt new file mode 100644 index 000000000000..00fc52a034b7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -0,0 +1,51 @@ +* Renesas R-Car generation 2 USB PHY + +This file provides information on what the device node for the R-Car generation +2 USB PHY contains. + +Required properties: +- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. +- reg: offset and length of the register block. +- #address-cells: number of address cells for the USB channel subnodes, must + be <1>. +- #size-cells: number of size cells for the USB channel subnodes, must be <0>. +- clocks: clock phandle and specifier pair. +- clock-names: string, clock input name, must be "usbhs". + +The USB PHY device tree node should have the subnodes corresponding to the USB +channels. These subnodes must contain the following properties: +- reg: the USB controller selector; see the table below for the values. +- #phy-cells: see phy-bindings.txt in the same directory, must be <1>. + +The phandle's argument in the PHY specifier is the USB controller selector for +the USB channel; see the selector meanings below: + ++-----------+---------------+---------------+ +|\ Selector | | | ++ --------- + 0 | 1 | +| Channel \| | | ++-----------+---------------+---------------+ +| 0 | PCI EHCI/OHCI | HS-USB | +| 2 | PCI EHCI/OHCI | xHCI | ++-----------+---------------+---------------+ + +Example (Lager board): + + usb-phy@e6590100 { + compatible = "renesas,usb-phy-r8a7790"; + reg = <0 0xe6590100 0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + clock-names = "usbhs"; + + usb-channel@0 { + reg = <0>; + #phy-cells = <1>; + }; + usb-channel@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 7a6feea2a48b..d5bad920827f 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -17,8 +17,11 @@ Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,exynos5250-dp-video-phy"; -- reg : offset and length of the Display Port PHY register set; +- compatible : should be one of the following supported values: + - "samsung,exynos5250-dp-video-phy" + - "samsung,exynos5420-dp-video-phy" +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. - #phy-cells : from the generic PHY bindings, must be 0; Samsung S5P/EXYNOS SoC series USB PHY @@ -125,6 +128,7 @@ Required properties: - compatible : Should be set to one of the following supported values: - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. + - "samsung,exynos7-usbdrd-phy" - for exynos7 SoC. - reg : Register offset and length of USB DRD PHY register set; - clocks: Clock IDs array as required by the controller - clock-names: names of clocks correseponding to IDs in the clock property; @@ -135,6 +139,11 @@ Required properties: PHY operations, associated by phy name. It is used to determine bit values for clock settings register. For Exynos5420 this is given as 'sclk_usbphy30' in CMU. + - optional clocks: Exynos7 SoC has now following additional + gate clocks available: + - phy_pipe: for PIPE3 phy + - phy_utmi: for UTMI+ phy + - itp: for ITP generation - samsung,pmu-syscon: phandle for PMU system controller interface, used to control pmu registers for power isolation. - #phy-cells : from the generic PHY bindings, must be 1; diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index 02ab5ab198a4..b7a93e80a302 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -19,6 +19,7 @@ such as pull-up, multi drive, etc. Required properties for iomux controller: - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl" + or "atmel,sama5d3-pinctrl" - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be configured in this periph mode. All the periph and bank need to be describe. @@ -85,13 +86,20 @@ Required properties for pin configuration node: PIN_BANK 0 is pioA, PIN_BANK 1 is pioB... Bits used for CONFIG: -PULL_UP (1 << 0): indicate this pin need a pull up. -MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. -DEGLITCH (1 << 2): indicate this pin need deglitch. -PULL_DOWN (1 << 3): indicate this pin need a pull down. -DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. -DEBOUNCE (1 << 16): indicate this pin need debounce. -DEBOUNCE_VAL (0x3fff << 17): debounce val. +PULL_UP (1 << 0): indicate this pin needs a pull up. +MULTIDRIVE (1 << 1): indicate this pin needs to be configured as multi-drive. + Multi-drive is equivalent to open-drain type output. +DEGLITCH (1 << 2): indicate this pin needs deglitch. +PULL_DOWN (1 << 3): indicate this pin needs a pull down. +DIS_SCHMIT (1 << 4): indicate this pin needs to the disable schmitt trigger. +DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the + following values: + 00 - No change (reset state value kept) + 01 - Low + 10 - Medium + 11 - High +DEBOUNCE (1 << 16): indicate this pin needs debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce value. NOTE: Some requirements for using atmel,at91rm9200-pinctrl binding: diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt index a186181c402b..51b943cc9770 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt index 4b27c99f7f9d..509faa87ad0e 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090's pin configuration nodes act as a container for an abitrary number of +TZ1090's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration @@ -67,7 +67,7 @@ Valid values for pin and group names are: They also all support the some form of muxing. Any pins which are contained in one of the mux groups (see below) can be muxed only to the functions supported by the mux group. All other pins can be muxed to the "perip" - function which which enables them with their intended peripheral. + function which enables them with their intended peripheral. Different pins in the same mux group cannot be muxed to different functions, however it is possible to mux only a subset of the pins in a mux group to a diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt index daa768956069..ac4da9fe07bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt index b5469db1d7ad..e89b4677567d 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt new file mode 100644 index 000000000000..17e7240c6998 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -0,0 +1,96 @@ +== Amlogic Meson pinmux controller == + +Required properties for the root node: + - compatible: "amlogic,meson8-pinctrl" + - reg: address and size of registers controlling irq functionality + +=== GPIO sub-nodes === + +The 2 power domains of the controller (regular and always-on) are +represented as sub-nodes and each of them acts as a GPIO controller. + +Required properties for sub-nodes are: + - reg: should contain address and size for mux, pull-enable, pull and + gpio register sets + - reg-names: an array of strings describing the "reg" entries. Must + contain "mux", "pull" and "gpio". "pull-enable" is optional and + when it is missing the "pull" registers are used instead + - gpio-controller: identifies the node as a gpio controller + - #gpio-cells: must be 2 + +Valid sub-node names are: + - "banks" for the regular domain + - "ao-bank" for the always-on domain + +=== Other sub-nodes === + +Child nodes without the "gpio-controller" represent some desired +configuration for a pin or a group. Those nodes can be pinmux nodes or +configuration nodes. + +Required properties for pinmux nodes are: + - groups: a list of pinmux groups. The list of all available groups + depends on the SoC and can be found in driver sources. + - function: the name of a function to activate for the specified set + of groups. The list of all available functions depends on the SoC + and can be found in driver sources. + +Required properties for configuration nodes: + - pins: a list of pin names + +Configuration nodes support the generic properties "bias-disable", +"bias-pull-up" and "bias-pull-down", described in file +pinctrl-bindings.txt + +=== Example === + + pinctrl: pinctrl@c1109880 { + compatible = "amlogic,meson8-pinctrl"; + reg = <0xc1109880 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio: banks@c11080b0 { + reg = <0xc11080b0 0x28>, + <0xc11080e8 0x18>, + <0xc1108120 0x18>, + <0xc1108030 0x30>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio_ao: ao-bank@c1108030 { + reg = <0xc8100014 0x4>, + <0xc810002c 0x4>, + <0xc8100024 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + nand { + mux { + groups = "nand_io", "nand_io_ce0", "nand_io_ce1", + "nand_io_rb0", "nand_ale", "nand_cle", + "nand_wen_clk", "nand_ren_clk", "nand_dqs", + "nand_ce2", "nand_ce3"; + function = "nand"; + }; + }; + + uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a", + "uart_cts_ao_a", "uart_rts_ao_a"; + function = "uart_ao"; + }; + + conf { + pins = "GPIOAO_0", "GPIOAO_1", + "GPIOAO_2", "GPIOAO_3"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt index 6464bf769460..189814e7cdc7 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt @@ -10,6 +10,7 @@ Required properties: - reg: Should contain a list of base address and size pairs for: -- first entry - the drive strength and pad control registers. -- second entry - the pinmux registers + -- third entry - the MIPI_PAD_CTRL register Tegra124 adds the following optional properties for pin configuration subnodes. The macros for options are defined in the @@ -91,6 +92,12 @@ Valid values for pin and group names are: dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4. + MIPI pad control groups: + + These support only the nvidia,function property. + + dsi_b + Valid values for nvidia,functions are: blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya, @@ -101,14 +108,15 @@ Valid values for nvidia,functions are: sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta, uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1, - dp, rtck, sys, clk tmds. + dp, rtck, sys, clk tmds, csi, dsi_b Example: pinmux: pinmux { compatible = "nvidia,tegra124-pinmux"; - reg = <0x70000868 0x164 /* Pad control registers */ - 0x70003000 0x434>; /* PinMux registers */ + reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */ + <0x0 0x70003000 0x0 0x434>, /* Mux registers */ + <0x0 0x70000820 0x0 0x8>; /* MIPI pad control */ }; Example pinmux entries: diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index 61e73cde9ae9..3c8ce28baad6 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Tegra's pin configuration nodes act as a container for an abitrary number of +Tegra's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index fa40a177164c..47d84b6ee91b 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -127,6 +127,24 @@ whether there is any interaction between the child and intermediate parent nodes, is again defined entirely by the binding for the individual pin controller device. +== Generic pin multiplexing node content == + +pin multiplexing nodes: + +function - the mux function to select +groups - the list of groups to select with this function + +Example: + +state_0_node_a { + function = "uart0"; + groups = "u0rxtx", "u0rtscts"; +}; +state_1_node_a { + function = "spi0"; + groups = "spi0pins"; +}; + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common @@ -139,8 +157,12 @@ structure of the DT nodes that contain these properties. Supported generic properties are: pins - the list of pins that properties in the node - apply to -function - the mux function to select + apply to (either this or "group" has to be + specified) +group - the group to apply the properties to, if the driver + supports configuration of whole groups rather than + individual pins (either this or "pins" has to be + specified) bias-disable - disable any pin bias bias-high-impedance - high impedance mode ("third-state", "floating") bias-bus-hold - latch weakly @@ -163,6 +185,21 @@ output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level slew-rate - set the slew rate +For example: + +state_0_node_a { + pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ + bias-pull-up; +}; +state_1_node_a { + pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */ + output-high; +}; +state_2_node_a { + group = "foo-group"; + bias-pull-up; +}; + Some of the generic properties take arguments. For those that do, the arguments are described below. @@ -170,15 +207,6 @@ arguments are described below. binding for the hardware defines: - Whether the entries are integers or strings, and their meaning. -- function takes a list of function names/IDs as a required argument. The - specific binding for the hardware defines: - - Whether the entries are integers or strings, and their meaning. - - Whether only a single entry is allowed (which is applied to all entries - in the pins property), or whether there may alternatively be one entry per - entry in the pins property, in which case the list lengths must match, and - for each list index i, the function at list index i is applied to the pin - at list index i. - - bias-pull-up, -down and -pin-default take as optional argument on hardware supporting it the pull strength in Ohm. bias-disable will disable the pull. @@ -188,4 +216,4 @@ arguments are described below. or 0 to disable debouncing More in-depth documentation on these parameters can be found in -<include/linux/pinctrl/pinconfig-generic.h> +<include/linux/pinctrl/pinconf-generic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt index c596a6ad3285..5f55be59d914 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -13,7 +13,7 @@ Optional properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes. +SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a group of pins. Required subnode-properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt index b4480d5c3aca..458615596946 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt @@ -32,7 +32,7 @@ Required properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each +SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents muxing for a pin, a group, or a list of pins or groups. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt index 92fae82f35f2..a7bde64798c7 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration @@ -50,7 +50,7 @@ Valid values for function are: gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, - riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, + riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold Example: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt new file mode 100644 index 000000000000..c4ea61ac56f2 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -0,0 +1,179 @@ +Qualcomm APQ8084 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8960 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,apq8084-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio146, + sdc1_clk, + sdc1_cmd, + sdc1_data + sdc2_clk, + sdc2_cmd, + sdc2_data + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3, + blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, + blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12, + blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10, + blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, + blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8, + blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12, + blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, + blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2, + cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i + gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio, + hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic, + ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst, + pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s, + qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n, + sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus, + spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1, + tsif2, uim, uim_batt_alarm + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@fd510000 { + compatible = "qcom,apq8084-pinctrl"; + reg = <0xfd510000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + uart2: uart2-default { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + + tx { + pins = "gpio4"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt index e33e4dcdce79..6e88e91feb11 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt index 93b7de91b9f6..eb8d8aa41f20 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -The pin configuration nodes act as a container for an abitrary number of +The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index d2ea80dc43eb..e4d6a9d20f7d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt new file mode 100644 index 000000000000..7ed08048516a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -0,0 +1,215 @@ +Qualcomm PMIC GPIO block + +This binding describes the GPIO block(s) found in the 8xxx series of +PMIC's from Qualcomm. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8018-gpio" + "qcom,pm8038-gpio" + "qcom,pm8058-gpio" + "qcom,pm8917-gpio" + "qcom,pm8921-gpio" + "qcom,pm8941-gpio" + "qcom,pma8084-gpio" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base of the GPIO block and length. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Must contain an array of encoded interrupt specifiers for + each available GPIO + +- gpio-controller: + Usage: required + Value type: <none> + Definition: Mark the device node as a GPIO controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: Must be 2; + the first cell will be used to define gpio number and the + second denotes the flags for this gpio + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin or a list of pins. This configuration can include the +mux function to select on those pin(s), and various pin configuration +parameters, as listed below. + + +SUBNODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio1-gpio6 for pm8018 + gpio1-gpio12 for pm8038 + gpio1-gpio40 for pm8058 + gpio1-gpio38 for pm8917 + gpio1-gpio44 for pm8921 + gpio1-gpio36 for pm8941 + gpio1-gpio22 for pma8084 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Valid values are: + "normal", + "paired", + "func1", + "func2", + "dtest1", + "dtest2", + "dtest3", + "dtest4" + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as pull down. + +- bias-pull-up: + Usage: optional + Value type: <empty> + Definition: The specified pins should be configured as pull up. + +- qcom,pull-up-strength: + Usage: optional + Value type: <u32> + Definition: Specifies the strength to use for pull up, if selected. + Valid values are; as defined in + <dt-bindings/pinctrl/qcom,pmic-gpio.h>: + 1: 30uA (PMIC_GPIO_PULL_UP_30) + 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5) + 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5) + 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30) + If this property is ommited 30uA strength will be used if + pull up is selected + +- bias-high-impedance: + Usage: optional + Value type: <none> + Definition: The specified pins will put in high-Z mode and disabled. + +- input-enable: + Usage: optional + Value type: <none> + Definition: The specified pins are put in input mode. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- power-source: + Usage: optional + Value type: <u32> + Definition: Selects the power source for the specified pins. Valid + power sources are defined per chip in + <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +- qcom,drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins. Value + drive strengths are: + 0: no (PMIC_GPIO_STRENGTH_NO) + 1: high (PMIC_GPIO_STRENGTH_HIGH) 0.9mA @ 1.8V - 1.9mA @ 2.6V + 2: medium (PMIC_GPIO_STRENGTH_MED) 0.6mA @ 1.8V - 1.25mA @ 2.6V + 3: low (PMIC_GPIO_STRENGTH_LOW) 0.15mA @ 1.8V - 0.3mA @ 2.6V + as defined in <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +- drive-push-pull: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in push-pull mode. + +- drive-open-drain: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in open-drain mode. + +- drive-open-source: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in open-source mode. + +Example: + + pm8921_gpio: gpio@150 { + compatible = "qcom,pm8921-gpio"; + reg = <0x150 0x160>; + interrupts = <192 1>, <193 1>, <194 1>, + <195 1>, <196 1>, <197 1>, + <198 1>, <199 1>, <200 1>, + <201 1>, <202 1>, <203 1>, + <204 1>, <205 1>, <206 1>, + <207 1>, <208 1>, <209 1>, + <210 1>, <211 1>, <212 1>, + <213 1>, <214 1>, <215 1>, + <216 1>, <217 1>, <218 1>, + <219 1>, <220 1>, <221 1>, + <222 1>, <223 1>, <224 1>, + <225 1>, <226 1>, <227 1>, + <228 1>, <229 1>, <230 1>, + <231 1>, <232 1>, <233 1>, + <234 1>, <235 1>; + + gpio-controller; + #gpio-cells = <2>; + + pm8921_gpio_keys: gpio-keys { + volume-keys { + pins = "gpio20", "gpio21"; + function = "normal"; + + input-enable; + bias-pull-up; + drive-push-pull; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8921_GPIO_S4>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt new file mode 100644 index 000000000000..854774b194ed --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -0,0 +1,162 @@ +Qualcomm PMIC Multi-Purpose Pin (MPP) block + +This binding describes the MPP block(s) found in the 8xxx series +of PMIC's from Qualcomm. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,pm8841-mpp", + "qcom,pm8941-mpp", + "qcom,pma8084-mpp", + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base of the MPP block and length. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Must contain an array of encoded interrupt specifiers for + each available MPP + +- gpio-controller: + Usage: required + Value type: <none> + Definition: Mark the device node as a GPIO controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: Must be 2; + the first cell will be used to define MPP number and the + second denotes the flags for this MPP + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin or a list of pins. This configuration can include the +mux function to select on those pin(s), and various pin configuration +parameters, as listed below. + +SUBNODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of MPP pins affected by the properties specified in + this subnode. Valid pins are: + mpp1-mpp4 for pm8841 + mpp1-mpp8 for pm8941 + mpp1-mpp4 for pma8084 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Valid values are: + "normal", + "paired", + "dtest1", + "dtest2", + "dtest3", + "dtest4" + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-up: + Usage: optional + Value type: <u32> + Definition: The specified pins should be configured as pull up. + Valid values are 600, 10000 and 30000 in bidirectional mode + only, i.e. when operating in qcom,analog-mode and input and + outputs are enabled. The hardware ignores the configuration + when operating in other modes. + +- bias-high-impedance: + Usage: optional + Value type: <none> + Definition: The specified pins will put in high-Z mode and disabled. + +- input-enable: + Usage: optional + Value type: <none> + Definition: The specified pins are put in input mode, i.e. their input + buffer is enabled + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- power-source: + Usage: optional + Value type: <u32> + Definition: Selects the power source for the specified pins. Valid power + sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +- qcom,analog-mode: + Usage: optional + Value type: <none> + Definition: Selects Analog mode of operation: combined with input-enable + and/or output-high, output-low MPP could operate as + Bidirectional Logic, Analog Input, Analog Output. + +- qcom,amux-route: + Usage: optional + Value type: <u32> + Definition: Selects the source for analog input. Valid values are + defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6... + +Example: + + mpps@a000 { + compatible = "qcom,pm8841-mpp"; + reg = <0xa000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>; + + pinctrl-names = "default"; + pinctrl-0 = <&pm8841_default>; + + pm8841_default: default { + gpio { + pins = "mpp1", "mpp2", "mpp3", "mpp4"; + function = "normal"; + input-enable; + power-source = <PM8841_MPP_S3>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 4658b69d4f4d..388b213249fd 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -2,8 +2,8 @@ The Rockchip Pinmux Controller, enables the IC to share one PAD to several functional blocks. The sharing is done by -multiplexing the PAD input/output signals. For each PAD there are up to -4 muxing options with option 0 being the use as a GPIO. +multiplexing the PAD input/output signals. For each PAD there are several +muxing options with option 0 being the use as a GPIO. Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -58,7 +58,7 @@ Deprecated properties for gpio sub nodes: Required properties for pin configuration node: - rockchip,pins: 3 integers array, represents a group of pins mux and config setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. - The MUX 0 means gpio and MUX 1 to 3 mean the specific device function. + The MUX 0 means gpio and MUX 1 to N mean the specific device function. The phandle of a node containing the generic pinconfig options to use, as described in pinctrl-bindings.txt in this directory. diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index e82aaf492517..8425838a6dff 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -18,6 +18,7 @@ Required Properties: - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. + - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. @@ -136,6 +137,8 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a found on Samsung S3C64xx SoCs, - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs. + - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller + found on Samsung Exynos7 SoC. - interrupt-parent: phandle of the interrupt parent to which the external wakeup interrupts are forwarded to. - interrupts: interrupt used by multiplexed wakeup interrupts. diff --git a/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt index e3865e136067..87697420439e 100644 --- a/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt +++ b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt @@ -8,42 +8,8 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -ST Ericsson's pin configuration nodes act as a container for an arbitrary number of -subnodes. Each of these subnodes represents some desired configuration for a -pin, a group, or a list of pins or groups. This configuration can include the -mux function to select on those pin(s)/group(s), and various pin configuration -parameters, such as input, output, pull up, pull down... - -The name of each subnode is not important; all subnodes should be enumerated -and processed purely based on their content. - -Required subnode-properties: -- ste,pins : An array of strings. Each string contains the name of a pin or - group. - -Optional subnode-properties: -- ste,function: A string containing the name of the function to mux to the - pin or group. - -- generic pin configuration option to use. Example : - - default_cfg { - ste,pins = "GPIO1"; - bias-disable; - }; - -- ste,config: Handle of pin configuration node containing the generic - pinconfig options to use, as described in pinctrl-bindings.txt in - this directory. Example : - - pcfg_bias_disable: pcfg_bias_disable { - bias-disable; - }; - - default_cfg { - ste,pins = "GPIO1"; - ste.config = <&pcfg_bias_disable>; - }; +ST Ericsson's pin configuration nodes use the generic pin multiplexing +and pin configuration bindings, see pinctrl-bindings.txt Example board file extract: @@ -54,11 +20,11 @@ Example board file extract: sysclkreq2 { sysclkreq2_default_mode: sysclkreq2_default { default_mux { - ste,function = "sysclkreq"; - ste,pins = "sysclkreq2_d_1"; + function = "sysclkreq"; + groups = "sysclkreq2_d_1"; }; default_cfg { - ste,pins = "GPIO1"; + pins = "GPIO1"; bias-disable; }; }; @@ -66,11 +32,11 @@ Example board file extract: sysclkreq3 { sysclkreq3_default_mode: sysclkreq3_default { default_mux { - ste,function = "sysclkreq"; - ste,pins = "sysclkreq3_d_1"; + function = "sysclkreq"; + groups = "sysclkreq3_d_1"; }; default_cfg { - ste,pins = "GPIO2"; + pins = "GPIO2"; output-low; }; }; @@ -78,11 +44,11 @@ Example board file extract: gpio3 { gpio3_default_mode: gpio3_default { default_mux { - ste,function = "gpio"; - ste,pins = "gpio3_a_1"; + function = "gpio"; + groups = "gpio3_a_1"; }; default_cfg { - ste,pins = "GPIO3"; + pins = "GPIO3"; output-low; }; }; @@ -90,11 +56,11 @@ Example board file extract: sysclkreq6 { sysclkreq6_default_mode: sysclkreq6_default { default_mux { - ste,function = "sysclkreq"; - ste,pins = "sysclkreq6_d_1"; + function = "sysclkreq"; + groups = "sysclkreq6_d_1"; }; default_cfg { - ste,pins = "GPIO4"; + pins = "GPIO4"; bias-disable; }; }; @@ -102,11 +68,11 @@ Example board file extract: pwmout1 { pwmout1_default_mode: pwmout1_default { default_mux { - ste,function = "pwmout"; - ste,pins = "pwmout1_d_1"; + function = "pwmout"; + groups = "pwmout1_d_1"; }; default_cfg { - ste,pins = "GPIO14"; + pins = "GPIO14"; output-low; }; }; @@ -114,11 +80,11 @@ Example board file extract: pwmout2 { pwmout2_default_mode: pwmout2_default { pwmout2_default_mux { - ste,function = "pwmout"; - ste,pins = "pwmout2_d_1"; + function = "pwmout"; + groups = "pwmout2_d_1"; }; pwmout2_default_cfg { - ste,pins = "GPIO15"; + pins = "GPIO15"; output-low; }; }; @@ -126,11 +92,11 @@ Example board file extract: pwmout3 { pwmout3_default_mode: pwmout3_default { pwmout3_default_mux { - ste,function = "pwmout"; - ste,pins = "pwmout3_d_1"; + function = "pwmout"; + groups = "pwmout3_d_1"; }; pwmout3_default_cfg { - ste,pins = "GPIO16"; + pins = "GPIO16"; output-low; }; }; @@ -139,15 +105,15 @@ Example board file extract: adi1_default_mode: adi1_default { adi1_default_mux { - ste,function = "adi1"; - ste,pins = "adi1_d_1"; + function = "adi1"; + groups = "adi1_d_1"; }; adi1_default_cfg1 { - ste,pins = "GPIO17","GPIO19","GPIO20"; + pins = "GPIO17","GPIO19","GPIO20"; bias-disable; }; adi1_default_cfg2 { - ste,pins = "GPIO18"; + pins = "GPIO18"; output-low; }; }; @@ -155,15 +121,15 @@ Example board file extract: dmic12 { dmic12_default_mode: dmic12_default { dmic12_default_mux { - ste,function = "dmic"; - ste,pins = "dmic12_d_1"; + function = "dmic"; + groups = "dmic12_d_1"; }; dmic12_default_cfg1 { - ste,pins = "GPIO27"; + pins = "GPIO27"; output-low; }; dmic12_default_cfg2 { - ste,pins = "GPIO28"; + pins = "GPIO28"; bias-disable; }; }; @@ -171,15 +137,15 @@ Example board file extract: dmic34 { dmic34_default_mode: dmic34_default { dmic34_default_mux { - ste,function = "dmic"; - ste,pins = "dmic34_d_1"; + function = "dmic"; + groups = "dmic34_d_1"; }; dmic34_default_cfg1 { - ste,pins = "GPIO29"; + pins = "GPIO29"; output-low; }; dmic34_default_cfg2 { - ste,pins = "GPIO30"; + pins = "GPIO30"; bias-disable;{ }; @@ -188,15 +154,15 @@ Example board file extract: dmic56 { dmic56_default_mode: dmic56_default { dmic56_default_mux { - ste,function = "dmic"; - ste,pins = "dmic56_d_1"; + function = "dmic"; + groups = "dmic56_d_1"; }; dmic56_default_cfg1 { - ste,pins = "GPIO31"; + pins = "GPIO31"; output-low; }; dmic56_default_cfg2 { - ste,pins = "GPIO32"; + pins = "GPIO32"; bias-disable; }; }; @@ -204,11 +170,11 @@ Example board file extract: sysclkreq5 { sysclkreq5_default_mode: sysclkreq5_default { sysclkreq5_default_mux { - ste,function = "sysclkreq"; - ste,pins = "sysclkreq5_d_1"; + function = "sysclkreq"; + groups = "sysclkreq5_d_1"; }; sysclkreq5_default_cfg { - ste,pins = "GPIO42"; + pins = "GPIO42"; output-low; }; }; @@ -216,11 +182,11 @@ Example board file extract: batremn { batremn_default_mode: batremn_default { batremn_default_mux { - ste,function = "batremn"; - ste,pins = "batremn_d_1"; + function = "batremn"; + groups = "batremn_d_1"; }; batremn_default_cfg { - ste,pins = "GPIO43"; + pins = "GPIO43"; bias-disable; }; }; @@ -228,11 +194,11 @@ Example board file extract: service { service_default_mode: service_default { service_default_mux { - ste,function = "service"; - ste,pins = "service_d_1"; + function = "service"; + groups = "service_d_1"; }; service_default_cfg { - ste,pins = "GPIO44"; + pins = "GPIO44"; bias-disable; }; }; @@ -240,13 +206,13 @@ Example board file extract: pwrctrl0 { pwrctrl0_default_mux: pwrctrl0_mux { pwrctrl0_default_mux { - ste,function = "pwrctrl"; - ste,pins = "pwrctrl0_d_1"; + function = "pwrctrl"; + groups = "pwrctrl0_d_1"; }; }; pwrctrl0_default_mode: pwrctrl0_default { pwrctrl0_default_cfg { - ste,pins = "GPIO45"; + pins = "GPIO45"; bias-disable; }; }; @@ -254,13 +220,13 @@ Example board file extract: pwrctrl1 { pwrctrl1_default_mux: pwrctrl1_mux { pwrctrl1_default_mux { - ste,function = "pwrctrl"; - ste,pins = "pwrctrl1_d_1"; + function = "pwrctrl"; + groups = "pwrctrl1_d_1"; }; }; pwrctrl1_default_mode: pwrctrl1_default { pwrctrl1_default_cfg { - ste,pins = "GPIO46"; + pins = "GPIO46"; bias-disable; }; }; @@ -268,11 +234,11 @@ Example board file extract: pwmextvibra1 { pwmextvibra1_default_mode: pwmextvibra1_default { pwmextvibra1_default_mux { - ste,function = "pwmextvibra"; - ste,pins = "pwmextvibra1_d_1"; + function = "pwmextvibra"; + groups = "pwmextvibra1_d_1"; }; pwmextvibra1_default_cfg { - ste,pins = "GPIO47"; + pins = "GPIO47"; bias-disable; }; }; @@ -280,11 +246,11 @@ Example board file extract: pwmextvibra2 { pwmextvibra2_default_mode: pwmextvibra2_default { pwmextvibra2_default_mux { - ste,function = "pwmextvibra"; - ste,pins = "pwmextvibra2_d_1"; + function = "pwmextvibra"; + groups = "pwmextvibra2_d_1"; }; pwmextvibra1_default_cfg { - ste,pins = "GPIO48"; + pins = "GPIO48"; bias-disable; }; }; @@ -292,11 +258,11 @@ Example board file extract: gpio51 { gpio51_default_mode: gpio51_default { gpio51_default_mux { - ste,function = "gpio"; - ste,pins = "gpio51_a_1"; + function = "gpio"; + groups = "gpio51_a_1"; }; gpio51_default_cfg { - ste,pins = "GPIO51"; + pins = "GPIO51"; output-low; }; }; @@ -304,11 +270,11 @@ Example board file extract: gpio52 { gpio52_default_mode: gpio52_default { gpio52_default_mux { - ste,function = "gpio"; - ste,pins = "gpio52_a_1"; + function = "gpio"; + groups = "gpio52_a_1"; }; gpio52_default_cfg { - ste,pins = "GPIO52"; + pins = "GPIO52"; bias-pull-down; }; }; @@ -316,11 +282,11 @@ Example board file extract: gpio53 { gpio53_default_mode: gpio53_default { gpio53_default_mux { - ste,function = "gpio"; - ste,pins = "gpio53_a_1"; + function = "gpio"; + groups = "gpio53_a_1"; }; gpio53_default_cfg { - ste,pins = "GPIO53"; + pins = "GPIO53"; bias-pull-down; }; }; @@ -328,11 +294,11 @@ Example board file extract: gpio54 { gpio54_default_mode: gpio54_default { gpio54_default_mux { - ste,function = "gpio"; - ste,pins = "gpio54_a_1"; + function = "gpio"; + groups = "gpio54_a_1"; }; gpio54_default_cfg { - ste,pins = "GPIO54"; + pins = "GPIO54"; output-low; }; }; @@ -340,11 +306,11 @@ Example board file extract: pdmclkdat { pdmclkdat_default_mode: pdmclkdat_default { pdmclkdat_default_mux { - ste,function = "pdm"; - ste,pins = "pdmclkdat_d_1"; + function = "pdm"; + groups = "pdmclkdat_d_1"; }; pdmclkdat_default_cfg { - ste,pins = "GPIO55", "GPIO56"; + pins = "GPIO55", "GPIO56"; bias-disable; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt new file mode 100644 index 000000000000..88c80273da91 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt @@ -0,0 +1,13 @@ +OMAP Pinctrl definitions + +Required properties: +- compatible : Should be one of: + "ti,omap2420-padconf" - OMAP2420 compatible pinctrl + "ti,omap2430-padconf" - OMAP2430 compatible pinctrl + "ti,omap3-padconf" - OMAP3 compatible pinctrl + "ti,omap4-padconf" - OMAP4 compatible pinctrl + "ti,omap5-padconf" - OMAP5 compatible pinctrl + "ti,dra7-padconf" - DRA7 compatible pinctrl + "ti,am437-padconf" - AM437x compatible pinctrl + +See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details. diff --git a/Documentation/devicetree/bindings/power/power-controller.txt b/Documentation/devicetree/bindings/power/power-controller.txt new file mode 100644 index 000000000000..4f7a3bc9c407 --- /dev/null +++ b/Documentation/devicetree/bindings/power/power-controller.txt @@ -0,0 +1,18 @@ +* Generic system power control capability + +Power-management integrated circuits or miscellaneous hardware components are +sometimes able to control the system power. The device driver associated with these +components might need to define this capability, which tells the kernel that +it can be used to switch off the system. The corresponding device must have the +standard property "system-power-controller" in its device node. This property +marks the device as able to control the system power. In order to test if this +property is found programmatically, use the helper function +"of_device_is_system_power_controller" from of.h . + +Example: + +act8846: act8846@5 { + compatible = "active-semi,act8846"; + status = "okay"; + system-power-controller; +} diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt new file mode 100644 index 000000000000..98c16672ab5f --- /dev/null +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -0,0 +1,49 @@ +* Generic PM domains + +System on chip designs are often divided into multiple PM domains that can be +used for power gating of selected IP blocks for power saving by reduced leakage +current. + +This device tree binding can be used to bind PM domain consumer devices with +their PM domains provided by PM domain providers. A PM domain provider can be +represented by any node in the device tree and can provide one or more PM +domains. A consumer node can refer to the provider by a phandle and a set of +phandle arguments (so called PM domain specifiers) of length specified by the +#power-domain-cells property in the PM domain provider node. + +==PM domain providers== + +Required properties: + - #power-domain-cells : Number of cells in a PM domain specifier; + Typically 0 for nodes representing a single PM domain and 1 for nodes + providing multiple PM domains (e.g. power controllers), but can be any value + as specified by device tree binding documentation of particular provider. + +Example: + + power: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + }; + +The node above defines a power controller that is a PM domain provider and +expects one cell as its phandle argument. + +==PM domain consumers== + +Required properties: + - power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle. + +Example: + + leaky-device@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 0>; + }; + +The node above defines a typical PM domain consumer device, which is located +inside a PM domain with index 0 of a power controller represented by a node +with the label "power". diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt new file mode 100644 index 000000000000..0c94c637f63b --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -0,0 +1,26 @@ +Binding for the LTC2952 PowerPath controller + +This chip is used to externally trigger a system shut down. Once the trigger has +been sent, the chips' watchdog has to be reset to gracefully shut down. +If the Linux systems decides to shut down it powers off the platform via the +kill signal. + +Required properties: + +- compatible: Must contain: "lltc,ltc2952" +- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's trigger line +- watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's watchdog line +- kill-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's kill line + +Example: + +ltc2952 { + compatible = "lltc,ltc2952"; + + trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt new file mode 100644 index 000000000000..809af54f02f3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -0,0 +1,11 @@ +*Device-Tree bindings for ST SW reset functionality + +Required properties: +- compatible: should be "st,<chip>-restart". +- st,syscfg: should be a phandle of the syscfg node. + +Example node: + restart { + compatible = "st,stih416-restart"; + st,syscfg = <&syscfg_sbc>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt new file mode 100644 index 000000000000..11906316b43d --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt @@ -0,0 +1,23 @@ +Generic SYSCON mapped register reset driver + +This is a generic reset driver using syscon to map the reset register. +The reset is generally performed with a write to the reset register +defined by the register map pointed by syscon reference plus the offset +with the mask defined in the reboot node. + +Required properties: +- compatible: should contain "syscon-reboot" +- regmap: this is phandle to the register map node +- offset: offset in the register map for the reboot register (in bytes) +- mask: the reset value written to the reboot register (32 bit access) + +Default will be little endian mode, 32 bit access only. + +Examples: + + reboot { + compatible = "syscon-reboot"; + regmap = <®mapnode>; + offset = <0x0>; + mask = <0x1>; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt new file mode 100644 index 000000000000..6fbf6e7ecde6 --- /dev/null +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -0,0 +1,83 @@ +Rockchip SRAM for IO Voltage Domains: +------------------------------------- + +IO domain voltages on some Rockchip SoCs are variable but need to be +kept in sync between the regulators and the SoC using a special +register. + +A specific example using rk3288: +- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then + bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to + that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1. + +Said another way, this driver simply handles keeping bits in the SoC's +general register file (GRF) in sync with the actual value of a voltage +hooked up to the pins. + +Note that this driver specifically doesn't include: +- any logic for deciding what voltage we should set regulators to +- any logic for deciding whether regulators (or internal SoC blocks) + should have power or not have power + +If there were some other software that had the smarts of making +decisions about regulators, it would work in conjunction with this +driver. When that other software adjusted a regulator's voltage then +this driver would handle telling the SoC about it. A good example is +vqmmc for SD. In that case the dw_mmc driver simply is told about a +regulator. It changes the regulator between 3.3V and 1.8V at the +right time. This driver notices the change and makes sure that the +SoC is on the same page. + + +Required properties: +- compatible: should be one of: + - "rockchip,rk3188-io-voltage-domain" for rk3188 + - "rockchip,rk3288-io-voltage-domain" for rk3288 +- rockchip,grf: phandle to the syscon managing the "general register files" + + +You specify supplies using the standard regulator bindings by including +a phandle the the relevant regulator. All specified supplies must be able +to report their voltage. The IO Voltage Domain for any non-specified +supplies will be not be touched. + +Possible supplies for rk3188: +- ap0-supply: The supply connected to AP0_VCC. +- ap1-supply: The supply connected to AP1_VCC. +- cif-supply: The supply connected to CIF_VCC. +- flash-supply: The supply connected to FLASH_VCC. +- lcdc0-supply: The supply connected to LCD0_VCC. +- lcdc1-supply: The supply connected to LCD1_VCC. +- vccio0-supply: The supply connected to VCCIO0. +- vccio1-supply: The supply connected to VCCIO1. + Sometimes also labeled VCCIO1 and VCCIO2. + +Possible supplies for rk3288: +- audio-supply: The supply connected to APIO4_VDD. +- bb-supply: The supply connected to APIO5_VDD. +- dvp-supply: The supply connected to DVPIO_VDD. +- flash0-supply: The supply connected to FLASH0_VDD. Typically for eMMC +- flash1-supply: The supply connected to FLASH1_VDD. Also known as SDIO1. +- gpio30-supply: The supply connected to APIO1_VDD. +- gpio1830 The supply connected to APIO2_VDD. +- lcdc-supply: The supply connected to LCDC_VDD. +- sdcard-supply: The supply connected to SDMMC0_VDD. +- wifi-supply: The supply connected to APIO3_VDD. Also known as SDIO0. + + +Example: + + io-domains { + compatible = "rockchip,rk3288-io-voltage-domain"; + rockchip,grf = <&grf>; + + audio-supply = <&vcc18_codec>; + bb-supply = <&vcc33_io>; + dvp-supply = <&vcc_18>; + flash0-supply = <&vcc18_flashio>; + gpio1830-supply = <&vcc33_io>; + gpio30-supply = <&vcc33_pmuio>; + lcdc-supply = <&vcc33_lcd>; + sdcard-supply = <&vccio_sd>; + wifi-supply = <&vcc18_wl>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/charger-manager.txt b/Documentation/devicetree/bindings/power_supply/charger-manager.txt index 2b33750e3db2..ec4fe9de3137 100644 --- a/Documentation/devicetree/bindings/power_supply/charger-manager.txt +++ b/Documentation/devicetree/bindings/power_supply/charger-manager.txt @@ -24,7 +24,7 @@ Optional properties : - cm-thermal-zone : name of external thermometer's thermal zone - cm-battery-* : threshold battery temperature for charging -cold : critical cold temperature of battery for charging - -cold-in-minus : flag that cold temerature is in minus degree + -cold-in-minus : flag that cold temperature is in minus degrees -hot : critical hot temperature of battery for charging -temp-diff : temperature difference to allow recharging - cm-dis/charging-max = limits of charging duration diff --git a/Documentation/devicetree/bindings/power_supply/gpio-charger.txt b/Documentation/devicetree/bindings/power_supply/gpio-charger.txt new file mode 100644 index 000000000000..adbb5dc5b6e9 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/gpio-charger.txt @@ -0,0 +1,27 @@ +gpio-charger + +Required properties : + - compatible : "gpio-charger" + - gpios : GPIO indicating the charger presence. + See GPIO binding in bindings/gpio/gpio.txt . + - charger-type : power supply type, one of + unknown + battery + ups + mains + usb-sdp (USB standard downstream port) + usb-dcp (USB dedicated charging port) + usb-cdp (USB charging downstream port) + usb-aca (USB accessory charger adapter) + +Example: + + usb_charger: charger { + compatible = "gpio-charger"; + charger-type = "usb-sdp"; + gpios = <&gpf0 2 0 0 0>; + } + + battery { + power-supplies = <&usb_charger>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt new file mode 100644 index 000000000000..dc7c9bad63ea --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt @@ -0,0 +1,23 @@ +i.mx6 Poweroff Driver + +SNVS_LPCR in SNVS module can power off the whole system by pull +PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. +If you don't want to use PMIC_ON_REQ as power on/off control, +please set status='disabled' to disable this driver. + +Required Properties: +-compatible: "fsl,sec-v4.0-poweroff" +-reg: Specifies the physical address of the SNVS_LPCR register + +Example: + snvs@020cc000 { + compatible = "fsl,sec-v4.0-mon", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x020cc000 0x4000>; + ..... + snvs_poweroff: snvs-poweroff@38 { + compatible = "fsl,sec-v4.0-poweroff"; + reg = <0x38 0x4>; + }; + } diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt new file mode 100644 index 000000000000..edeea160ca39 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt @@ -0,0 +1,534 @@ +============================================================================= +Freescale Frame Manager Device Bindings + +CONTENTS + - FMan Node + - FMan Port Node + - FMan MURAM Node + - FMan dTSEC/XGEC/mEMAC Node + - FMan IEEE 1588 Node + - Example + +============================================================================= +FMan Node + +DESCRIPTION + +Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs, +etc.) the FMan node will have child nodes for each of them. + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must include "fsl,fman" + FMan version can be determined via FM_IP_REV_1 register in the + FMan block. The offset is 0xc4 from the beginning of the + Frame Processing Manager memory map (0xc3000 from the + beginning of the FMan node). + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the index of the FMan unit. + + The cell-index value may be used by the SoC, to identify the + FMan unit in the SoC memory map. In the table bellow, + there's a description of the cell-index use in each SoC: + + - P1023: + register[bit] FMan unit cell-index + ============================================================ + DEVDISR[1] 1 0 + + - P2041, P3041, P4080 P5020, P5040: + register[bit] FMan unit cell-index + ============================================================ + DCFG_DEVDISR2[6] 1 0 + DCFG_DEVDISR2[14] 2 1 + (Second FM available only in P4080 and P5040) + + - B4860, T1040, T2080, T4240: + register[bit] FMan unit cell-index + ============================================================ + DCFG_CCSR_DEVDISR2[24] 1 0 + DCFG_CCSR_DEVDISR2[25] 2 1 + (Second FM available only in T4240) + + DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in + the specific SoC "Device Configuration/Pin Control" Memory + Map. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the offset of the + following configuration registers: + - BMI configuration registers. + - QMI configuration registers. + - DMA configuration registers. + - FPM configuration registers. + - FMan controller configuration registers. + +- ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +- clocks + Usage: required + Value type: <prop-encoded-array> + Definition: phandle for the fman input clock. + +- clock-names + usage: required + Value type: <stringlist> + Definition: "fmanclk" for the fman input clock. + +- interrupts + Usage: required + Value type: <prop-encoded-array> + Definition: A pair of IRQs are specified in this property. + The first element is associated with the event interrupts and + the second element is associated with the error interrupts. + +- fsl,qman-channel-range + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies the range of the available dedicated + channels in the FMan. The first cell specifies the beginning + of the range and the second cell specifies the number of + channels. + Further information available at: + "Work Queue (WQ) Channel Assignments in the QMan" section + in DPAA Reference Manual. + +- fsl,qman +- fsl,bman + Usage: required + Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt + +============================================================================= +FMan MURAM Node + +DESCRIPTION + +FMan Internal memory - shared between all the FMan modules. +It contains data structures that are common and written to or read by +the modules. +FMan internal memory is split into the following parts: + Packet buffering (Tx/Rx FIFOs) + Frames internal context + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must include "fsl,fman-muram" + +- ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + Specifies the multi-user memory offset and the size within + the FMan. + +EXAMPLE + +muram@0 { + compatible = "fsl,fman-muram"; + ranges = <0 0x000000 0x28000>; +}; + +============================================================================= +FMan Port Node + +DESCRIPTION + +The Frame Manager (FMan) supports several types of hardware ports: + Ethernet receiver (RX) + Ethernet transmitter (TX) + Offline/Host command (O/H) + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include one of the following: + - "fsl,fman-v2-port-oh" for FManV2 OH ports + - "fsl,fman-v2-port-rx" for FManV2 RX ports + - "fsl,fman-v2-port-tx" for FManV2 TX ports + - "fsl,fman-v3-port-oh" for FManV3 OH ports + - "fsl,fman-v3-port-rx" for FManV3 RX ports + - "fsl,fman-v3-port-tx" for FManV3 TX ports + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the hardware port id. + Each hardware port on the FMan has its own hardware PortID. + Super set of all hardware Port IDs available at FMan Reference + Manual under "FMan Hardware Ports in Freescale Devices" table. + + Each hardware port is assigned a 4KB, port-specific page in + the FMan hardware port memory region (which is part of the + FMan memory map). The first 4 KB in the FMan hardware ports + memory region is used for what are called common registers. + The subsequent 63 4KB pages are allocated to the hardware + ports. + The page of a specific port is determined by the cell-index. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: There is one reg region describing the port + configuration registers. + +EXAMPLE + +port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; +}; + +port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; +}; + +port@81000 { + cell-index = <0x1>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x81000 0x1000>; +}; + +============================================================================= +FMan dTSEC/XGEC/mEMAC Node + +DESCRIPTION + +mEMAC/dTSEC/XGEC are the Ethernet network interfaces + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include one of the following: + - "fsl,fman-dtsec" for dTSEC MAC + - "fsl,fman-xgec" for XGEC MAC + - "fsl,fman-memac for mEMAC MAC + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the MAC id. + + The cell-index value may be used by the FMan or the SoC, to + identify the MAC unit in the FMan (or SoC) memory map. + In the tables bellow there's a description of the cell-index + use, there are two tables, one describes the use of cell-index + by the FMan, the second describes the use by the SoC: + + 1. FMan Registers + + FManV2: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16] XGEC 8 + FM_EPI[16+n] dTSECn n-1 + FM_NPI[11+n] dTSECn n-1 + n = 1,..,5 + + FManV3: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16+n] mEMACn n-1 + FM_EPI[25] mEMAC10 9 + + FM_NPI[11+n] mEMACn n-1 + FM_NPI[10] mEMAC10 9 + FM_NPI[11] mEMAC9 8 + n = 1,..8 + + FM_EPI and FM_NPI are located in the FMan memory map. + + 2. SoC registers: + + - P2041, P3041, P4080 P5020, P5040: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_DEVDISR2[7] 1 XGEC 8 + DCFG_DEVDISR2[7+n] 1 dTSECn n-1 + DCFG_DEVDISR2[15] 2 XGEC 8 + DCFG_DEVDISR2[15+n] 2 dTSECn n-1 + n = 1,..5 + + - T1040, T2080, T4240, B4860: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1 + DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1 + n = 1,..6,9,10 + + EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in + the specific SoC "Device Configuration/Pin Control" Memory + Map. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +- fsl,fman-ports + Usage: required + Value type: <prop-encoded-array> + Definition: An array of two phandles - the first references is + the FMan RX port and the second is the TX port used by this + MAC. + +- ptp-timer + Usage required + Value type: <phandle> + Definition: A phandle for 1EEE1588 timer. + +EXAMPLE + +fman1_tx28: port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; +}; + +fman1_rx8: port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; +}; + +ptp-timer: ptp_timer@fe000 { + compatible = "fsl,fman-ptp-timer"; + reg = <0xfe000 0x1000>; +}; + +ethernet@e0000 { + compatible = "fsl,fman-dtsec"; + cell-index = <0>; + reg = <0xe0000 0x1000>; + fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; + ptp-timer = <&ptp-timer>; +}; + +============================================================================ +FMan IEEE 1588 Node + +DESCRIPTION + +The FMan interface to support IEEE 1588 + + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include "fsl,fman-ptp-timer". + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +EXAMPLE + +ptp-timer@fe000 { + compatible = "fsl,fman-ptp-timer"; + reg = <0xfe000 0x1000>; +}; + +============================================================================= +Example + +fman@400000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + compatible = "fsl,fman" + ranges = <0 0x400000 0x100000>; + reg = <0x400000 0x100000>; + clocks = <&fman_clk>; + clock-names = "fmanclk"; + interrupts = < + 96 2 0 0 + 16 2 1 1>; + fsl,qman-channel-range = <0x40 0xc>; + + muram@0 { + compatible = "fsl,fman-muram"; + reg = <0x0 0x28000>; + }; + + port@81000 { + cell-index = <1>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x81000 0x1000>; + }; + + port@82000 { + cell-index = <2>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x82000 0x1000>; + }; + + port@83000 { + cell-index = <3>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x83000 0x1000>; + }; + + port@84000 { + cell-index = <4>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x84000 0x1000>; + }; + + port@85000 { + cell-index = <5>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x85000 0x1000>; + }; + + port@86000 { + cell-index = <6>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x86000 0x1000>; + }; + + fman1_rx_0x8: port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; + }; + + fman1_rx_0x9: port@89000 { + cell-index = <0x9>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x89000 0x1000>; + }; + + fman1_rx_0xa: port@8a000 { + cell-index = <0xa>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8a000 0x1000>; + }; + + fman1_rx_0xb: port@8b000 { + cell-index = <0xb>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8b000 0x1000>; + }; + + fman1_rx_0xc: port@8c000 { + cell-index = <0xc>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8c000 0x1000>; + }; + + fman1_rx_0x10: port@90000 { + cell-index = <0x10>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x90000 0x1000>; + }; + + fman1_tx_0x28: port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; + }; + + fman1_tx_0x29: port@a9000 { + cell-index = <0x29>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa9000 0x1000>; + }; + + fman1_tx_0x2a: port@aa000 { + cell-index = <0x2a>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xaa000 0x1000>; + }; + + fman1_tx_0x2b: port@ab000 { + cell-index = <0x2b>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xab000 0x1000>; + }; + + fman1_tx_0x2c: port@ac0000 { + cell-index = <0x2c>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xac000 0x1000>; + }; + + fman1_tx_0x30: port@b0000 { + cell-index = <0x30>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xb0000 0x1000>; + }; + + ethernet@e0000 { + compatible = "fsl,fman-dtsec"; + cell-index = <0>; + reg = <0xe0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>; + }; + + ethernet@e2000 { + compatible = "fsl,fman-dtsec"; + cell-index = <1>; + reg = <0xe2000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>; + }; + + ethernet@e4000 { + compatible = "fsl,fman-dtsec"; + cell-index = <2>; + reg = <0xe4000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>; + }; + + ethernet@e6000 { + compatible = "fsl,fman-dtsec"; + cell-index = <3>; + reg = <0xe6000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>; + }; + + ethernet@e8000 { + compatible = "fsl,fman-dtsec"; + cell-index = <4>; + reg = <0xf0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>; + + ethernet@f0000 { + cell-index = <8>; + compatible = "fsl,fman-xgec"; + reg = <0xf0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>; + }; + + ptp-timer@fe000 { + compatible = "fsl,fman-ptp-timer"; + reg = <0xfe000 0x1000>; + }; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt index 0bda229a6171..3899d6a557c1 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -1,5 +1,20 @@ Freescale FlexTimer Module (FTM) PWM controller +The same FTM PWM device can have a different endianness on different SoCs. The +device tree provides a property to describing this so that an operating system +device driver can handle all variants of the device. Refer to the table below +for the endianness of the FTM PWM block as integrated into the existing SoCs: + + SoC | FTM-PWM endianness + --------+------------------- + Vybrid | LE + LS1 | BE + LS2 | LE + +Please see ../regmap/regmap.txt for more detail about how to specify endian +modes in device tree. + + Required properties: - compatible: Should be "fsl,vf610-ftm-pwm". - reg: Physical base address and length of the controller's registers @@ -16,7 +31,8 @@ Required properties: - pinctrl-names: Must contain a "default" entry. - pinctrl-NNN: One property must exist for each entry in pinctrl-names. See pinctrl/pinctrl-bindings.txt for details of the property values. - +- big-endian: Boolean property, required if the FTM PWM registers use a big- + endian rather than little-endian layout. Example: @@ -32,4 +48,5 @@ pwm0: pwm@40038000 { <&clks VF610_CLK_FTM0_EXT_FIX_EN>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0_1>; + big-endian; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt index d47d15a6a298..b8be3d09ee26 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -7,8 +7,8 @@ Required properties: "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC - reg: physical base address and length of the controller's registers - clocks: phandle and clock specifier of the PWM reference clock - - #pwm-cells: should be 2. See pwm.txt in this directory for a - description of the cell format. + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + for a description of the cell format. Example: diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt new file mode 100644 index 000000000000..b494f8b8ef72 --- /dev/null +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -0,0 +1,47 @@ +Device-Tree binding for regmap + +The endianness mode of CPU & Device scenarios: +Index Device Endianness properties +--------------------------------------------------- +1 BE 'big-endian' +2 LE 'little-endian' + +For one device driver, which will run in different scenarios above +on different SoCs using the devicetree, we need one way to simplify +this. + +Required properties: +- {big,little}-endian: these are boolean properties, if absent + meaning that the CPU and the Device are in the same endianness mode, + these properties are for register values and all the buffers only. + +Examples: +Scenario 1 : CPU in LE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... +}; + +Scenario 2 : CPU in LE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + big-endian; +}; + +Scenario 3 : CPU in BE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... +}; + +Scenario 4 : CPU in BE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + little-endian; +}; diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index 865614b34d6f..dad6358074ac 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -5,6 +5,10 @@ Required properties: - compatible: "active-semi,act8846" or "active-semi,act8865" - reg: I2C slave address +Optional properties: +- system-power-controller: Telling whether or not this pmic is controlling + the system power. See Documentation/devicetree/bindings/power/power-controller.txt . + Any standard regulator properties can be used to configure the single regulator. The valid names for regulators are: diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index f120f229d67d..3297c53cb915 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -2,7 +2,7 @@ Required properties: -- compatible: must be "diasemi,da9210" +- compatible: must be "dlg,da9210" - reg: the i2c slave address of the regulator. It should be 0x68. Any standard regulator properties can be used to configure the single da9210 @@ -11,7 +11,7 @@ DCDC. Example: da9210@68 { - compatible = "diasemi,da9210"; + compatible = "dlg,da9210"; reg = <0x68>; regulator-min-microvolt = <900000>; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt new file mode 100644 index 000000000000..240019a82f9a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -0,0 +1,63 @@ +* Dialog Semiconductor DA9211/DA9213 Voltage Regulator + +Required properties: +- compatible: "dlg,da9211" or "dlg,da9213". +- reg: I2C slave address, usually 0x68. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCKA and BUCKB. + +Optional properties: +- Any optional property defined in regulator.txt + +Example 1) DA9211 + + pmic: da9211@68 { + compatible = "dlg,da9211"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + }; + }; + }; + +Example 2) DA92113 + pmic: da9213@68 { + compatible = "dlg,da9213"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt new file mode 100644 index 000000000000..54a3f2c80e3a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -0,0 +1,23 @@ +Binding for Fairchild FAN53555 regulators + +Required properties: + - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - reg: I2C address + +Optional properties: + - fcs,suspend-voltage-selector: declare which of the two available + voltage selector registers should be used for the suspend + voltage. The other one is used for the runtime voltage setting + Possible values are either <0> or <1> + - vin-supply: regulator supplying the vin pin + +Example: + + regulator@40 { + compatible = "fcs,fan53555"; + regulator-name = "fan53555"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&parent_reg>; + fcs,suspend-voltage-selector = <1>; + }; diff --git a/Documentation/devicetree/bindings/regulator/isl9305.txt b/Documentation/devicetree/bindings/regulator/isl9305.txt new file mode 100644 index 000000000000..a626fc1bbf0d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/isl9305.txt @@ -0,0 +1,36 @@ +Intersil ISL9305/ISL9305H voltage regulator + +Required properties: + +- compatible: "isl,isl9305" or "isl,isl9305h" +- reg: I2C slave address, usually 0x68. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values being "dcd1", "dcd2", "ldo1" and "ldo2". The content of each sub-node + is defined by the standard binding for regulators; see regulator.txt. +- VINDCD1-supply: A phandle to a regulator node supplying VINDCD1. + VINDCD2-supply: A phandle to a regulator node supplying VINDCD2. + VINLDO1-supply: A phandle to a regulator node supplying VINLDO1. + VINLDO2-supply: A phandle to a regulator node supplying VINLDO2. + +Optional properties: +- Per-regulator optional properties are defined in regulator.txt + +Example + + pmic: isl9305@68 { + compatible = "isl,isl9305"; + reg = <0x68>; + + VINDCD1-supply = <&system_power>; + VINDCD2-supply = <&system_power>; + VINLDO1-supply = <&system_power>; + VINLDO2-supply = <&system_power>; + + regulators { + dcd1 { + regulator-name = "VDD_DSP"; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max1586-regulator.txt b/Documentation/devicetree/bindings/regulator/max1586-regulator.txt new file mode 100644 index 000000000000..c050c1744cb8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max1586-regulator.txt @@ -0,0 +1,28 @@ +Maxim MAX1586 voltage regulator + +Required properties: +- compatible: must be "maxim,max1586" +- reg: I2C slave address, usually 0x14 +- v3-gain: integer specifying the V3 gain as per datasheet + (1 + R24/R25 + R24/185.5kOhm) +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max1586@14 { + compatible = "maxim,max1586"; + reg = <0x14>; + v3-gain = <1000000>; + + regulators { + vcc_core: v3 { + regulator-name = "vcc_core"; + regulator-compatible = "Output_V3"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1705000>; + regulator-always-on; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt new file mode 100644 index 000000000000..79e5476444f7 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -0,0 +1,88 @@ +Binding for Maxim MAX77802 regulators + +This is a part of device tree bindings of MAX77802 multi-function device. +More information can be found in bindings/mfd/max77802.txt file. + +The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout (LDO) +regulators that can be controlled over I2C. + +Following properties should be present in main device node of the MFD chip. + +Optional node: +- regulators : The regulators of max77802 have to be instantiated + under subnode named "regulators" using the following format. + + regulator-name { + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + +The regulator node name should be initialized with a string to get matched +with their hardware counterparts as follow. The valid names are: + + -LDOn : for LDOs, where n can lie in ranges 1-15, 17-21, 23-30 + and 32-35. + example: LDO1, LDO2, LDO35. + -BUCKn : for BUCKs, where n can lie in range 1 to 10. + example: BUCK1, BUCK5, BUCK10. + +The max77802 regulator supports two different operating modes: Normal and Low +Power Mode. Some regulators support the modes to be changed at startup or by +the consumers during normal operation while others only support to change the +mode during system suspend. The standard regulator suspend states binding can +be used to configure the regulator operating mode. + +The regulators that support the standard "regulator-initial-mode" property, +changing their mode during normal operation are: LDOs 1, 3, 20 and 21. + +The possible values for "regulator-initial-mode" and "regulator-mode" are: + 1: Normal regulator voltage output mode. + 3: Low Power which reduces the quiescent current down to only 1uA + +The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +header and can be included by device tree source files. + +The standard "regulator-mode" property can only be used for regulators that +support changing their mode to Low Power Mode during suspend. These regulators +are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has +been enabled for the given suspend state using "regulator-on-in-suspend" and +has not been disabled for that state using "regulator-off-in-suspend". + +Example: + + max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #address-cells = <1>; + #size-cells = <0>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_1v0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-initial-mode = <MAX77802_OPMODE_LP>; + }; + + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-mode = <MAX77802_OPMODE_LP>; + }; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt new file mode 100644 index 000000000000..ce91f61feb12 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -0,0 +1,27 @@ +pwm regulator bindings + +Required properties: +- compatible: Should be "pwm-regulator" +- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) +- voltage-table: voltage and duty table, include 2 members in each set of + brackets, first one is voltage(unit: uv), the next is duty(unit: percent) + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + + voltage-table = <1114000 0>, + <1095000 10>, + <1076000 20>, + <1056000 30>, + <1036000 40>, + <1016000 50>; + + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 86074334e342..abb26b58c83e 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -19,6 +19,24 @@ Optional properties: design requires. This property describes the total system ramp time required due to the combination of internal ramping of the regulator itself, and board design issues such as trace capacitance and load on the supply. +- regulator-state-mem sub-root node for Suspend-to-RAM mode + : suspend to memory, the device goes to sleep, but all data stored in memory, + only some external interrupt can wake the device. +- regulator-state-disk sub-root node for Suspend-to-DISK mode + : suspend to disk, this state operates similarly to Suspend-to-RAM, + but includes a final step of writing memory contents to disk. +- regulator-state-[mem/disk] node has following common properties: + - regulator-on-in-suspend: regulator should be on in suspend state. + - regulator-off-in-suspend: regulator should be off in suspend state. + - regulator-suspend-microvolt: regulator should be set to this voltage + in suspend. + - regulator-mode: operating mode in the given suspend state. + The set of possible operating modes depends on the capabilities of + every hardware so the valid modes are documented on each regulator + device tree binding document. +- regulator-initial-mode: initial operating mode. The set of possible operating + modes depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple @@ -34,6 +52,10 @@ Example: regulator-max-microvolt = <2500000>; regulator-always-on; vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; }; Regulator Consumers: diff --git a/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt new file mode 100644 index 000000000000..f9acbc1f3c6b --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt @@ -0,0 +1,18 @@ +SKY81452 voltage regulator + +Required properties: +- regulator node named lout. +- any required generic properties defined in regulator.txt + +Optional properties: +- any available generic properties defined in regulator.txt + +Example: + + regulator { + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt new file mode 100644 index 000000000000..54ae9f747e45 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt @@ -0,0 +1,42 @@ +STMicroelectronics STi family Sysconfig Picophy SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in +the STi family SoC system configuration registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to Documentation/devicetree/bindings/reset/reset.txt +for common reset controller binding usage. + +Required properties: +- compatible: Should be "st,stih407-picophyreset" +- #reset-cells: 1, see below + +Example: + + picophyreset: picophyreset-controller { + compatible = "st,stih407-picophyreset"; + #reset-cells = <1>; + }; + +Specifying picophyreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the picophyreset device node and an +index specifying which channel to use, as described in +Documentation/devicetree/bindings/reset/reset.txt. + +Example: + + usb2_picophy0: usbpicophy@0 { + resets = <&picophyreset STIH407_PICOPHY0_RESET>; + }; + +Macro definitions for the supported reset channels can be found in: +include/dt-bindings/reset-controller/stih407-resets.h diff --git a/Documentation/devicetree/bindings/rng/apm,rng.txt b/Documentation/devicetree/bindings/rng/apm,rng.txt new file mode 100644 index 000000000000..4dde4b06cdd9 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/apm,rng.txt @@ -0,0 +1,17 @@ +APM X-Gene SoC random number generator. + +Required properties: + +- compatible : should be "apm,xgene-rng" +- reg : specifies base physical address and size of the registers map +- clocks : phandle to clock-controller plus clock-specifier pair +- interrupts : specify the fault interrupt for the RNG device + +Example: + + rng: rng@10520000 { + compatible = "apm,xgene-rng"; + reg = <0x0 0x10520000 0x0 0x100>; + interrupts = <0x0 0x41 0x4>; + clocks = <&rngpkaclk 0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt new file mode 100644 index 000000000000..6ae79d1843f3 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt @@ -0,0 +1,23 @@ +Atmel AT91SAM9260 Real Time Timer + +Required properties: +- compatible: should be: "atmel,at91sam9260-rtt" +- reg: should encode the memory region of the RTT controller +- interrupts: rtt alarm/event interrupt +- clocks: should contain the 32 KHz slow clk that will drive the RTT block. +- atmel,rtt-rtc-time-reg: should encode the GPBR register used to store + the time base when the RTT is used as an RTC. + The first cell should point to the GPBR node and the second one + encode the offset within the GPBR block (or in other words, the + GPBR register used to store the time base). + + +Example: + +rtt@fffffd20 { + compatible = "atmel,at91sam9260-rtt"; + reg = <0xfffffd20 0x10>; + interrupts = <1 4 7>; + clocks = <&clk32k>; + atmel,rtt-rtc-time-reg = <&gpbr 0x0>; +}; diff --git a/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt b/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt new file mode 100644 index 000000000000..916f57601a8f --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt @@ -0,0 +1,18 @@ +* Dallas DS1339 I2C Serial Real-Time Clock + +Required properties: +- compatible: Should contain "dallas,ds1339". +- reg: I2C address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable for ds1339 are 250, 2000, 4000 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + ds1339: rtc@68 { + compatible = "dallas,ds1339"; + trickle-resistor-ohms = <250>; + reg = <0x68>; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt index 5a0f02d34d95..4ba4dbd34289 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-omap.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt @@ -5,11 +5,17 @@ Required properties: - "ti,da830-rtc" - for RTC IP used similar to that on DA8xx SoC family. - "ti,am3352-rtc" - for RTC IP used similar to that on AM335x SoC family. This RTC IP has special WAKE-EN Register to enable - Wakeup generation for event Alarm. + Wakeup generation for event Alarm. It can also be + used to control an external PMIC via the + pmic_power_en pin. - reg: Address range of rtc register set - interrupts: rtc timer, alarm interrupts in order - interrupt-parent: phandle for the interrupt controller +Optional properties: +- system-power-controller: whether the rtc is controlling the system power + through pmic_power_en + Example: rtc@1c23000 { @@ -18,4 +24,5 @@ rtc@1c23000 { interrupts = <19 19>; interrupt-parent = <&intc>; + system-power-controller; }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-opal.txt b/Documentation/devicetree/bindings/rtc/rtc-opal.txt new file mode 100644 index 000000000000..af87e5ecac54 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-opal.txt @@ -0,0 +1,16 @@ +IBM OPAL real-time clock +------------------------ + +Required properties: +- comapatible: Should be "ibm,opal-rtc" + +Optional properties: +- has-tpo: Decides if the wakeup is supported or not. + +Example: + rtc { + compatible = "ibm,opal-rtc"; + has-tpo; + phandle = <0x10000029>; + linux,phandle = <0x10000029>; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 7ac7259fe9ea..ab757b84daa7 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -3,7 +3,10 @@ Required properties: - compatible: should be one of the following. * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc. + * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc. + * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc. * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc. + * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc. - reg: physical base address of the controller and length of memory mapped region. - interrupts: Two interrupt numbers to the cpu should be specified. First diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt new file mode 100644 index 000000000000..f007e428a1ab --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -0,0 +1,17 @@ +* sun6i Real Time Clock + +RTC controller for the Allwinner A31 + +Required properties: +- compatible : Should be "allwinner,sun6i-a31-rtc" +- reg : physical base address of the controller and length of + memory mapped region. +- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. + +Example: + +rtc: rtc@01f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x54>; + interrupts = <0 40 4>, <0 41 4>; +}; diff --git a/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt b/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt new file mode 100644 index 000000000000..5c52e5eef16d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt @@ -0,0 +1,30 @@ +* BCM63xx UART + +Required properties: + +- compatible: "brcm,bcm6345-uart" + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- clocks: Clock driving the hardware; used to figure out the baud rate + divisor. + +Example: + + uart0: serial@14e00520 { + compatible = "brcm,bcm6345-uart"; + reg = <0x14e00520 0x18>; + interrupt-parent = <&periph_intc>; + interrupts = <2>; + clocks = <&periph_clk>; + }; + + clocks { + periph_clk: periph_clk@0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <54000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt index 12f3cf834deb..caaeb2583579 100644 --- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt +++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt @@ -8,7 +8,8 @@ Required properties: - syscon: Phandle to SYSCON node, which contain UART control bits. Optional properties: -- uart-use-ms: Indicate the UART has modem signal (DCD, DSR, CTS). +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. Note: Each UART port should have an alias correctly numbered in "aliases" node. @@ -24,5 +25,7 @@ Example: interrupts = <12 13>; clocks = <&clks 11>; syscon = <&syscon1>; - uart-use-ms; + cts-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>; + dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>; + dcd-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt index 59a40f18d551..7c408c87e613 100644 --- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt @@ -11,8 +11,13 @@ Required properties: - dma-names: "rx" for RX channel, "tx" for TX channel. Optional properties: -- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines, +- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines + for hardware flow control, it also means you enable the DMA support for this UART. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. It will use specified PIO instead of the peripheral + function pin for the USART feature. + If unsure, don't specify this property. Example: auart0: serial@8006a000 { @@ -21,6 +26,9 @@ auart0: serial@8006a000 { interrupts = <112>; dmas = <&dma_apbx 8>, <&dma_apbx 9>; dma-names = "rx", "tx"; + cts-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; }; Note: Each auart port should have an alias correctly numbered in "aliases" diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt new file mode 100644 index 000000000000..48358a33ea7d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -0,0 +1,22 @@ +* Mediatek Universal Asynchronous Receiver/Transmitter (UART) + +Required properties: +- compatible should contain: + * "mediatek,mt6589-uart" for MT6589 compatible UARTS + * "mediatek,mt6582-uart" for MT6582 compatible UARTS + * "mediatek,mt6577-uart" for all compatible UARTS (MT6589, MT6582, MT6577) + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- clocks: Clock driving the hardware. + +Example: + + uart0: serial@11006000 { + compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart"; + reg = <0x11006000 0x400>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>; + }; diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 77054772a8f4..b52b98234b9b 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -10,10 +10,12 @@ Required properties: - "ns16850" - "nvidia,tegra20-uart" - "nxp,lpc3220-uart" + - "ralink,rt2880-uart" - "ibm,qpace-nwp-serial" - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" + - "fsl,16550-FIFO64" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. @@ -37,7 +39,6 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. -- has-hw-flow-control: the hardware has flow control capability. Example: diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt index 5d2e840ae65c..ba3ecb8cb5a1 100644 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -6,12 +6,46 @@ Required properties: - interrupts: exactly one interrupt specifier Optional properties: -- pinctrl: When present, must have one state named "sleep" - and one state named "default" -- clocks: When present, must refer to exactly one clock named +- pinctrl: + When present, must have one state named "default", + and may contain a second name named "sleep". The former + state sets up pins for ordinary operation whereas + the latter state will put the associated pins to sleep + when the UART is unused +- clocks: + When present, the first clock listed must correspond to + the clock named UARTCLK on the IP block, i.e. the clock + to the external serial line, whereas the second clock + must correspond to the PCLK clocking the internal logic + of the block. Just listing one clock (the first one) is + deprecated. +- clocks-names: + When present, the first clock listed must be named + "uartclk" and the second clock listed must be named "apb_pclk" -- dmas: When present, may have one or two dma channels. +- dmas: + When present, may have one or two dma channels. The first one must be named "rx", the second one must be named "tx". +- auto-poll: + Enables polling when using RX DMA. +- poll-rate-ms: + Rate at which poll occurs when auto-poll is set, + default 100ms. +- poll-timeout-ms: + Poll timeout when auto-poll is set, default + 3000ms. See also bindings/arm/primecell.txt + +Example: + +uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&foo_clk>, <&bar_clk>; + clock-names = "uartclk", "apb_pclk"; +}; diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index ffa5b784c66e..a2114c217376 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -27,27 +27,52 @@ Optional properties: - dmas: Should contain dma specifiers for transmit and receive channels - dma-names: Should contain "tx" for transmit and "rx" for receive channels +Note: Aliases may be defined to ensure the correct ordering of the UARTs. +The alias serialN will result in the UART being assigned port N. If any +serialN alias exists, then an alias must exist for each enabled UART. The +serialN aliases should be in a .dts file instead of in a .dtsi file. + Examples: -A uartdm v1.4 device with dma capabilities. - -serial@f991e000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0xf991e000 0x1000>; - interrupts = <0 108 0x0>; - clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>; - clock-names = "core", "iface"; - dmas = <&dma0 0>, <&dma0 1>; - dma-names = "tx", "rx"; -}; - -A uartdm v1.3 device without dma capabilities and part of a GSBI complex. - -serial@19c40000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x19c40000 0x1000>, - <0x19c00000 0x1000>; - interrupts = <0 195 0x0>; - clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>; - clock-names = "core", "iface"; -}; +- A uartdm v1.4 device with dma capabilities. + + serial@f991e000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0xf991e000 0x1000>; + interrupts = <0 108 0x0>; + clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>; + clock-names = "core", "iface"; + dmas = <&dma0 0>, <&dma0 1>; + dma-names = "tx", "rx"; + }; + +- A uartdm v1.3 device without dma capabilities and part of a GSBI complex. + + serial@19c40000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x19c40000 0x1000>, + <0x19c00000 0x1000>; + interrupts = <0 195 0x0>; + clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>; + clock-names = "core", "iface"; + }; + +- serialN alias. + + aliases { + serial0 = &uarta; + serial1 = &uartc; + serial2 = &uartb; + }; + + uarta: serial@12490000 { + status = "ok"; + }; + + uartb: serial@16340000 { + status = "ok"; + }; + + uartc: serial@1a240000 { + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index b3556609a06f..ae73bb0e9ad9 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,8 +4,7 @@ Required properties: - compatible: Must contain one of the following: - - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,scif-r7s72100" for R7S72100 (RZ/A1H) SCIF compatible UART. - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. @@ -20,6 +19,12 @@ Required properties: - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2) SCIFA compatible UART. - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2) SCIFB compatible UART. - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2) HSCIF compatible UART. + - "renesas,scif-r8a7794" for R8A7794 (R-Car E2) SCIF compatible UART. + - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART. + - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART. + - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. + - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. + - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,scif" for generic SCIF compatible UART. - "renesas,scifa" for generic SCIFA compatible UART. - "renesas,scifb" for generic SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt index a2dfc6522a91..3acdd969edf1 100644 --- a/Documentation/devicetree/bindings/serial/sirf-uart.txt +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -1,7 +1,9 @@ * CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter * Required properties: -- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart" +- compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart", + "sirf,marco-uart" or "sirf,marco-bt-uart" which means + uart located in BT module and used for BT. - reg : Offset and length of the register set for the device - interrupts : Should contain uart interrupt - fifosize : Should define hardware rx/tx fifo size @@ -31,3 +33,15 @@ usp@b0090000 { rts-gpios = <&gpio 15 0>; cts-gpios = <&gpio 46 0>; }; + +for uart use in BT module, +uart6: uart@11000000 { + cell-index = <6>; + compatible = "sirf,marco-bt-uart", "sirf,marco-uart"; + reg = <0x11000000 0x1000>; + interrupts = <0 100 0>; + clocks = <&clks 138>, <&clks 140>, <&clks 141>; + clock-names = "uart", "general", "noc"; + fifosize = <128>; + status = "disabled"; +} diff --git a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt deleted file mode 100644 index 5feef1ef167d..000000000000 --- a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt +++ /dev/null @@ -1,17 +0,0 @@ -VIA/Wondermedia VT8500 UART Controller ------------------------------------------------------ - -Required properties: -- compatible : "via,vt8500-uart" -- reg : Should contain 1 register ranges(address and length) -- interrupts : UART interrupt -- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock) - -Example: - - uart@d8210000 { - compatible = "via,vt8500-uart"; - reg = <0xd8210000 0x1040>; - interrupts = <47>; - clocks = <&ref24>; - }; diff --git a/Documentation/devicetree/bindings/serial/vt8500-uart.txt b/Documentation/devicetree/bindings/serial/vt8500-uart.txt index 795c393d09c4..2b64e6107fb3 100644 --- a/Documentation/devicetree/bindings/serial/vt8500-uart.txt +++ b/Documentation/devicetree/bindings/serial/vt8500-uart.txt @@ -1,7 +1,8 @@ * VIA VT8500 and WonderMedia WM8xxx UART Controller Required properties: -- compatible: should be "via,vt8500-uart" +- compatible: should be "via,vt8500-uart" (for VIA/WonderMedia chips up to and + including WM8850/WM8950), or "wm,wm8880-uart" (for WM8880 and later) - reg: base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/soc/fsl/bman-portals.txt b/Documentation/devicetree/bindings/soc/fsl/bman-portals.txt new file mode 100644 index 000000000000..2a00e14e11e0 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/bman-portals.txt @@ -0,0 +1,56 @@ +QorIQ DPAA Buffer Manager Portals Device Tree Binding + +Copyright (C) 2008 - 2014 Freescale Semiconductor Inc. + +CONTENTS + + - BMan Portal + - Example + +BMan Portal Node + +Portals are memory mapped interfaces to BMan that allow low-latency, lock-less +interaction by software running on processor cores, accelerators and network +interfaces with the BMan + +PROPERTIES + +- compatible + Usage: Required + Value type: <stringlist> + Definition: Must include "fsl,bman-portal-<hardware revision>" + May include "fsl,<SoC>-bman-portal" or "fsl,bman-portal" + +- reg + Usage: Required + Value type: <prop-encoded-array> + Definition: Two regions. The first is the cache-enabled region of + the portal. The second is the cache-inhibited region of + the portal + +- interrupts + Usage: Required + Value type: <prop-encoded-array> + Definition: Standard property + +EXAMPLE + +The example below shows a (P4080) BMan portals container/bus node with two portals + + bman-portals@ff4000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0xf 0xf4000000 0x200000>; + + bman-portal@0 { + compatible = "fsl,bman-portal-1.0.0", "fsl,bman-portal"; + reg = <0x0 0x4000>, <0x100000 0x1000>; + interrupts = <105 2 0 0>; + }; + bman-portal@4000 { + compatible = "fsl,bman-portal-1.0.0", "fsl,bman-portal"; + reg = <0x4000 0x4000>, <0x101000 0x1000>; + interrupts = <107 2 0 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/fsl/bman.txt b/Documentation/devicetree/bindings/soc/fsl/bman.txt new file mode 100644 index 000000000000..9f80bf8709ac --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/bman.txt @@ -0,0 +1,125 @@ +QorIQ DPAA Buffer Manager Device Tree Bindings + +Copyright (C) 2008 - 2014 Freescale Semiconductor Inc. + +CONTENTS + + - BMan Node + - BMan Private Memory Node + - Example + +BMan Node + +The Buffer Manager is part of the Data-Path Acceleration Architecture (DPAA). +BMan supports hardware allocation and deallocation of buffers belonging to pools +originally created by software with configurable depletion thresholds. This +binding covers the CCSR space programming model + +PROPERTIES + +- compatible + Usage: Required + Value type: <stringlist> + Definition: Must include "fsl,bman" + May include "fsl,<SoC>-bman" + +- reg + Usage: Required + Value type: <prop-encoded-array> + Definition: Registers region within the CCSR address space + +The BMan revision information is located in the BMAN_IP_REV_1/2 registers which +are located at offsets 0xbf8 and 0xbfc + +- interrupts + Usage: Required + Value type: <prop-encoded-array> + Definition: Standard property. The error interrupt + +- fsl,liodn + Usage: See pamu.txt + Value type: <prop-encoded-array> + Definition: PAMU property used for static LIODN assignment + +- fsl,iommu-parent + Usage: See pamu.txt + Value type: <phandle> + Definition: PAMU property used for dynamic LIODN assignment + + For additional details about the PAMU/LIODN binding(s) see pamu.txt + +Devices connected to a BMan instance via Direct Connect Portals (DCP) must link +to the respective BMan instance + +- fsl,bman + Usage: Required + Value type: <prop-encoded-array> + Description: List of phandle and DCP index pairs, to the BMan instance + to which this device is connected via the DCP + +BMan Private Memory Node + +BMan requires a contiguous range of physical memory used for the backing store +for BMan Free Buffer Proxy Records (FBPR). This memory is reserved/allocated as a +node under the /reserved-memory node + +The BMan FBPR memory node must be named "bman-fbpr" + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must inclide "fsl,bman-fbpr" + +The following constraints are relevant to the FBPR private memory: + - The size must be 2^(size + 1), with size = 11..33. That is 4 KiB to + 16 GiB + - The alignment must be a muliptle of the memory size + +The size of the FBPR must be chosen by observing the hardware features configured +via the Reset Configuration Word (RCW) and that are relevant to a specific board +(e.g. number of MAC(s) pinned-out, number of offline/host command FMan ports, +etc.). The size configured in the DT must reflect the hardware capabilities and +not the specific needs of an application + +For additional details about reserved memory regions see reserved-memory.txt + +EXAMPLE + +The example below shows a BMan FBPR dynamic allocation memory node + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + bman_fbpr: bman-fbpr { + compatible = "fsl,bman-fbpr"; + alloc-ranges = <0 0 0xf 0xffffffff>; + size = <0 0x1000000>; + alignment = <0 0x1000000>; + }; + }; + +The example below shows a (P4080) BMan CCSR-space node + + crypto@300000 { + ... + fsl,bman = <&bman, 2>; + ... + }; + + bman: bman@31a000 { + compatible = "fsl,bman"; + reg = <0x31a000 0x1000>; + interrupts = <16 2 1 2>; + fsl,liodn = <0x17>; + memory-region = <&bman_fbpr>; + }; + + fman@400000 { + ... + fsl,bman = <&bman, 0>; + ... + }; diff --git a/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt b/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt new file mode 100644 index 000000000000..48c4dae5d6f9 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt @@ -0,0 +1,154 @@ +QorIQ DPAA Queue Manager Portals Device Tree Binding + +Copyright (C) 2008 - 2014 Freescale Semiconductor Inc. + +CONTENTS + + - QMan Portal + - QMan Pool Channel + - Example + +QMan Portal Node + +Portals are memory mapped interfaces to QMan that allow low-latency, lock-less +interaction by software running on processor cores, accelerators and network +interfaces with the QMan + +PROPERTIES + +- compatible + Usage: Required + Value type: <stringlist> + Definition: Must include "fsl,qman-portal-<hardware revision>" + May include "fsl,<SoC>-qman-portal" or "fsl,qman-portal" + +- reg + Usage: Required + Value type: <prop-encoded-array> + Definition: Two regions. The first is the cache-enabled region of + the portal. The second is the cache-inhibited region of + the portal + +- interrupts + Usage: Required + Value type: <prop-encoded-array> + Definition: Standard property + +- fsl,liodn + Usage: See pamu.txt + Value type: <prop-encoded-array> + Definition: Two LIODN(s). DQRR LIODN (DLIODN) and Frame LIODN + (FLIODN) + +- fsl,iommu-parent + Usage: See pamu.txt + Value type: <phandle> + Definition: PAMU property used for dynamic LIODN assignment + + For additional details about the PAMU/LIODN binding(s) see pamu.txt + +- fsl,qman-channel-id + Usage: Required + Value type: <u32> + Definition: The hardware index of the channel. This can also be + determined by dividing any of the channel's 8 work queue + IDs by 8 + +In addition to these properties the qman-portals should have sub-nodes to +represent the HW devices/portals that are connected to the software portal +described here + +The currently supported sub-nodes are: + * fman0 + * fman1 + * pme + * crypto + +These subnodes should have the following properties: + +- fsl,liodn + Usage: See pamu.txt + Value type: <prop-encoded-array> + Definition: PAMU property used for static LIODN assignment + +- fsl,iommu-parent + Usage: See pamu.txt + Value type: <phandle> + Definition: PAMU property used for dynamic LIODN assignment + +- dev-handle + Usage: Required + Value type: <phandle> + Definition: The phandle to the particular hardware device that this + portal is connected to. + +DPAA QMan Pool Channel Nodes + +Pool Channels are defined with the following properties. + +PROPERTIES + +- compatible + Usage: Required + Value type: <stringlist> + Definition: Must include "fsl,qman-pool-channel" + May include "fsl,<SoC>-qman-pool-channel" + +- fsl,qman-channel-id + Usage: Required + Value type: <u32> + Definition: The hardware index of the channel. This can also be + determined by dividing any of the channel's 8 work queue + IDs by 8 + +EXAMPLE + +The example below shows a (P4080) QMan portals container/bus node with two portals + + qman-portals@ff4200000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0xf 0xf4200000 0x200000>; + + qman-portal@0 { + compatible = "fsl,qman-portal-1.2.0", "fsl,qman-portal"; + reg = <0 0x4000>, <0x100000 0x1000>; + interrupts = <104 2 0 0>; + fsl,liodn = <1 2>; + fsl,qman-channel-id = <0>; + + fman0 { + fsl,liodn = <0x21>; + dev-handle = <&fman0>; + }; + fman1 { + fsl,liodn = <0xa1>; + dev-handle = <&fman1>; + }; + crypto { + fsl,liodn = <0x41 0x66>; + dev-handle = <&crypto>; + }; + }; + qman-portal@4000 { + compatible = "fsl,qman-portal-1.2.0", "fsl,qman-portal"; + reg = <0x4000 0x4000>, <0x101000 0x1000>; + interrupts = <106 2 0 0>; + fsl,liodn = <3 4>; + fsl,qman-channel-id = <1>; + + fman0 { + fsl,liodn = <0x22>; + dev-handle = <&fman0>; + }; + fman1 { + fsl,liodn = <0xa2>; + dev-handle = <&fman1>; + }; + crypto { + fsl,liodn = <0x42 0x67>; + dev-handle = <&crypto>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/fsl/qman.txt b/Documentation/devicetree/bindings/soc/fsl/qman.txt new file mode 100644 index 000000000000..063e3a0b9d04 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/qman.txt @@ -0,0 +1,165 @@ +QorIQ DPAA Queue Manager Device Tree Binding + +Copyright (C) 2008 - 2014 Freescale Semiconductor Inc. + +CONTENTS + + - QMan Node + - QMan Private Memory Nodes + - Example + +QMan Node + +The Queue Manager is part of the Data-Path Acceleration Architecture (DPAA). QMan +supports queuing and QoS scheduling of frames to CPUs, network interfaces and +DPAA logic modules, maintains packet ordering within flows. Besides providing +flow-level queuing, is also responsible for congestion management functions such +as RED/WRED, congestion notifications and tail discards. This binding covers the +CCSR space programming model + +PROPERTIES + +- compatible + Usage: Required + Value type: <stringlist> + Definition: Must include "fsl,qman" + May include "fsl,<SoC>-qman" + +- reg + Usage: Required + Value type: <prop-encoded-array> + Definition: Registers region within the CCSR address space + +The QMan revision information is located in the QMAN_IP_REV_1/2 registers which +are located at offsets 0xbf8 and 0xbfc + +- interrupts + Usage: Required + Value type: <prop-encoded-array> + Definition: Standard property. The error interrupt + +- fsl,liodn + Usage: See pamu.txt + Value type: <prop-encoded-array> + Definition: PAMU property used for static LIODN assignment + +- fsl,iommu-parent + Usage: See pamu.txt + Value type: <phandle> + Definition: PAMU property used for dynamic LIODN assignment + + For additional details about the PAMU/LIODN binding(s) see pamu.txt + +- clocks + Usage: See clock-bindings.txt and qoriq-clock.txt + Value type: <prop-encoded-array> + Definition: Reference input clock. Its frequency is half of the + platform clock + +Devices connected to a QMan instance via Direct Connect Portals (DCP) must link +to the respective QMan instance + +- fsl,qman + Usage: Required + Value type: <prop-encoded-array> + Description: List of phandle and DCP index pairs, to the QMan instance + to which this device is connected via the DCP + +QMan Private Memory Nodes + +QMan requires two contiguous range of physical memory used for the backing store +for QMan Frame Queue Descriptor (FQD) and Packed Frame Descriptor Record (PFDR). +This memory is reserved/allocated as a nodes under the /reserved-memory node + +The QMan FQD memory node must be named "qman-fqd" + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must inclide "fsl,qman-fqd" + +The QMan PFDR memory node must be named "qman-pfdr" + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must inclide "fsl,qman-pfdr" + +The following constraints are relevant to the FQD and PFDR private memory: + - The size must be 2^(size + 1), with size = 11..29. That is 4 KiB to + 1 GiB + - The alignment must be a muliptle of the memory size + +The size of the FQD and PFDP must be chosen by observing the hardware features +configured via the Reset Configuration Word (RCW) and that are relevant to a +specific board (e.g. number of MAC(s) pinned-out, number of offline/host command +FMan ports, etc.). The size configured in the DT must reflect the hardware +capabilities and not the specific needs of an application + +For additional details about reserved memory regions see reserved-memory.txt + +EXAMPLE + +The example below shows a QMan FQD and a PFDR dynamic allocation memory nodes + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + qman_fqd: qman-fqd { + compatible = "fsl,qman-fqd"; + alloc-ranges = <0 0 0xf 0xffffffff>; + size = <0 0x400000>; + alignment = <0 0x400000>; + }; + qman_pfdr: qman-pfdr { + compatible = "fsl,qman-pfdr"; + alloc-ranges = <0 0 0xf 0xffffffff>; + size = <0 0x2000000>; + alignment = <0 0x2000000>; + }; + }; + +The example below shows a (P4080) QMan CCSR-space node + + clockgen: global-utilities@e1000 { + ... + sysclk: sysclk { + ... + }; + ... + platform_pll: platform-pll@c00 { + #clock-cells = <1>; + reg = <0xc00 0x4>; + compatible = "fsl,qoriq-platform-pll-1.0"; + clocks = <&sysclk>; + clock-output-names = "platform-pll", "platform-pll-div2"; + }; + ... + }; + + crypto@300000 { + ... + fsl,qman = <&qman, 2>; + ... + }; + + qman: qman@318000 { + compatible = "fsl,qman"; + reg = <0x318000 0x1000>; + interrupts = <16 2 1 3> + fsl,liodn = <0x16>; + memory-region = <&qman_fqd &qman_pfdr>; + clocks = <&platform_pll 1>; + }; + + fman@400000 { + ... + fsl,qman = <&qman, 0>; + ... + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt new file mode 100644 index 000000000000..337c4ea5c57b --- /dev/null +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt @@ -0,0 +1,111 @@ +Keystone Navigator DMA Controller + +This document explains the device tree bindings for the packet dma +on keystone devices. The Keystone Navigator DMA driver sets up the dma +channels and flows for the QMSS(Queue Manager SubSystem) who triggers +the actual data movements across clients using destination queues. Every +client modules like NETCP(Network Coprocessor), SRIO(Serial Rapid IO), +CRYPTO Engines etc has its own instance of dma hardware. QMSS has also +an internal packet DMA module which is used as an infrastructure DMA +with zero copy. + +Navigator DMA cloud layout: + ------------------ + | Navigator DMAs | + ------------------ + | + |-> DMA instance #0 + | + |-> DMA instance #1 + . + . + | + |-> DMA instance #n + +Navigator DMA properties: +Required properties: + - compatible: Should be "ti,keystone-navigator-dma" + - clocks: phandle to dma instances clocks. The clock handles can be as + many as the dma instances. The order should be maintained as per + the dma instances. + - ti,navigator-cloud-address: Should contain base address for the multi-core + navigator cloud and number of addresses depends on SOC integration + configuration.. Navigator cloud global address needs to be programmed + into DMA and the DMA uses it as the physical addresses to reach queue + managers. Note that these addresses though points to queue managers, + they are relevant only from DMA perspective. The QMSS may not choose to + use them since it has a different address space view to reach all + its components. + +DMA instance properties: +Required properties: + - reg: Should contain register location and length of the following dma + register regions. Register regions should be specified in the following + order. + - Global control register region (global). + - Tx DMA channel configuration register region (txchan). + - Rx DMA channel configuration register region (rxchan). + - Tx DMA channel Scheduler configuration register region (txsched). + - Rx DMA flow configuration register region (rxflow). + +Optional properties: + - reg-names: Names for the register regions. + - ti,enable-all: Enable all DMA channels vs clients opening specific channels + what they need. This property is useful for the userspace fast path + case where the linux drivers enables the channels used by userland + stack. + - ti,loop-back: To loopback Tx streaming I/F to Rx streaming I/F. Used for + infrastructure transfers. + - ti,rx-retry-timeout: Number of dma cycles to wait before retry on buffer + starvation. + +Example: + + knav_dmas: knav_dmas@0 { + compatible = "ti,keystone-navigator-dma"; + clocks = <&papllclk>, <&clkxge>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,navigator-cloud-address = <0x23a80000 0x23a90000 + 0x23aa0000 0x23ab0000>; + + dma_gbe: dma_gbe@0 { + reg = <0x2004000 0x100>, + <0x2004400 0x120>, + <0x2004800 0x300>, + <0x2004c00 0x120>, + <0x2005000 0x400>; + reg-names = "global", "txchan", "rxchan", + "txsched", "rxflow"; + }; + + dma_xgbe: dma_xgbe@0 { + reg = <0x2fa1000 0x100>, + <0x2fa1400 0x200>, + <0x2fa1800 0x200>, + <0x2fa1c00 0x200>, + <0x2fa2000 0x400>; + reg-names = "global", "txchan", "rxchan", + "txsched", "rxflow"; + }; + }; + +Navigator DMA client: +Required properties: + - ti,navigator-dmas: List of one or more DMA specifiers, each consisting of + - A phandle pointing to DMA instance node + - A DMA channel number as a phandle arg. + - ti,navigator-dma-names: Contains dma channel name for each DMA specifier in + the 'ti,navigator-dmas' property. + +Example: + + netcp: netcp@2090000 { + .. + ti,navigator-dmas = <&dma_gbe 22>, + <&dma_gbe 23>, + <&dma_gbe 8>; + ti,navigator-dma-names = "netrx0", "netrx1", "nettx"; + .. + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt new file mode 100644 index 000000000000..d8e8cdb733f9 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -0,0 +1,232 @@ +* Texas Instruments Keystone Navigator Queue Management SubSystem driver + +The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of +the main hardware sub system which forms the backbone of the Keystone +multi-core Navigator. QMSS consist of queue managers, packed-data structure +processors(PDSP), linking RAM, descriptor pools and infrastructure +Packet DMA. +The Queue Manager is a hardware module that is responsible for accelerating +management of the packet queues. Packets are queued/de-queued by writing or +reading descriptor address to a particular memory mapped location. The PDSPs +perform QMSS related functions like accumulation, QoS, or event management. +Linking RAM registers are used to link the descriptors which are stored in +descriptor RAM. Descriptor RAM is configurable as internal or external memory. +The QMSS driver manages the PDSP setups, linking RAM regions, +queue pool management (allocation, push, pop and notify) and descriptor +pool management. + + +Required properties: +- compatible : Must be "ti,keystone-navigator-qmss"; +- clocks : phandle to the reference clock for this device. +- queue-range : <start number> total range of queue numbers for the device. +- linkram0 : <address size> for internal link ram, where size is the total + link ram entries. +- linkram1 : <address size> for external link ram, where size is the total + external link ram entries. If the address is specified as "0" + driver will allocate memory. +- qmgrs : child node describing the individual queue managers on the + SoC. On keystone 1 devices there should be only one node. + On keystone 2 devices there can be more than 1 node. + -- managed-queues : the actual queues managed by each queue manager + instance, specified as <"base queue #" "# of queues">. + -- reg : Address and size of the register set for the device. + Register regions should be specified in the following + order + - Queue Peek region. + - Queue status RAM. + - Queue configuration region. + - Descriptor memory setup region. + - Queue Management/Queue Proxy region for queue Push. + - Queue Management/Queue Proxy region for queue Pop. +- queue-pools : child node classifying the queue ranges into pools. + Queue ranges are grouped into 3 type of pools: + - qpend : pool of qpend(interruptible) queues + - general-purpose : pool of general queues, primarly used + as free descriptor queues or the + transmit DMA queues. + - accumulator : pool of queues on PDSP accumulator channel + Each range can have the following properties: + -- qrange : number of queues to use per queue range, specified as + <"base queue #" "# of queues">. + -- interrupts : Optional property to specify the interrupt mapping + for interruptible queues. The driver additionaly sets + the interrupt affinity hint based on the cpu mask. + -- qalloc-by-id : Optional property to specify that the queues in this + range can only be allocated by queue id. + -- accumulator : Accumulator channel specification. Any of the PDSPs in + QMSS can be loaded with the accumulator firmware. The + accumulator firmware’s job is to poll a select number of + queues looking for descriptors that have been pushed + into them. Descriptors are popped from the queue and + placed in a buffer provided by the host. When the list + becomes full or a programmed time period expires, the + accumulator triggers an interrupt to the host to read + the buffer for descriptor information. This firmware + comes in 16, 32, and 48 channel builds. Each of these + channels can be configured to monitor 32 contiguous + queues. Accumulator channel property is specified as: + <pdsp-id, channel, entries, pacing mode, latency> + pdsp-id : QMSS PDSP running accumulator firmware + on which the channel has to be + configured + channel : Accumulator channel number + entries : Size of the accumulator descriptor list + pacing mode : Interrupt pacing mode + 0 : None, i.e interrupt on list full only + 1 : Time delay since last interrupt + 2 : Time delay since first new packet + 3 : Time delay since last new packet + latency : time to delay the interrupt, specified + in microseconds. + -- multi-queue : Optional property to specify that the channel has to + monitor upto 32 queues starting at the base queue #. +- descriptor-regions : child node describing the memory regions for keystone + navigator packet DMA descriptors. The memory for + descriptors will be allocated by the driver. + -- id : region number in QMSS. + -- region-spec : specifies the number of descriptors in the + region, specified as + <"# of descriptors" "descriptor size">. + -- link-index : start index, i.e. index of the first + descriptor in the region. + +Optional properties: +- dma-coherent : Present if DMA operations are coherent. +- pdsps : child node describing the PDSP configuration. + -- firmware : firmware to be loaded on the PDSP. + -- id : the qmss pdsp that will run the firmware. + -- reg : Address and size of the register set for the PDSP. + Register regions should be specified in the following + order + - PDSP internal RAM region. + - PDSP control/status region registers. + - QMSS interrupt distributor registers. + - PDSP command interface region. + +Example: + +qmss: qmss@2a40000 { + compatible = "ti,keystone-qmss"; + dma-coherent; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&chipclk13>; + ranges; + queue-range = <0 0x4000>; + linkram0 = <0x100000 0x8000>; + linkram1 = <0x0 0x10000>; + + qmgrs { + #address-cells = <1>; + #size-cells = <1>; + ranges; + qmgr0 { + managed-queues = <0 0x2000>; + reg = <0x2a40000 0x20000>, + <0x2a06000 0x400>, + <0x2a02000 0x1000>, + <0x2a03000 0x1000>, + <0x23a80000 0x20000>, + <0x2a80000 0x20000>; + }; + + qmgr1 { + managed-queues = <0x2000 0x2000>; + reg = <0x2a60000 0x20000>, + <0x2a06400 0x400>, + <0x2a04000 0x1000>, + <0x2a05000 0x1000>, + <0x23aa0000 0x20000>, + <0x2aa0000 0x20000>; + }; + }; + queue-pools { + qpend { + qpend-0 { + qrange = <658 8>; + interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04 + 0 43 0xf04 0 44 0xf04 0 45 0xf04 + 0 46 0xf04 0 47 0xf04>; + }; + qpend-1 { + qrange = <8704 16>; + interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04 + 0 51 0xf04 0 52 0xf04 0 53 0xf04 + 0 54 0xf04 0 55 0xf04 0 56 0xf04 + 0 57 0xf04 0 58 0xf04 0 59 0xf04 + 0 60 0xf04 0 61 0xf04 0 62 0xf04 + 0 63 0xf04>; + qalloc-by-id; + }; + qpend-2 { + qrange = <8720 16>; + interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04 + 0 59 0xf04 0 68 0xf04 0 69 0xf04 + 0 70 0xf04 0 71 0xf04 0 72 0xf04 + 0 73 0xf04 0 74 0xf04 0 75 0xf04 + 0 76 0xf04 0 77 0xf04 0 78 0xf04 + 0 79 0xf04>; + }; + }; + general-purpose { + gp-0 { + qrange = <4000 64>; + }; + netcp-tx { + qrange = <640 9>; + qalloc-by-id; + }; + }; + accumulator { + acc-0 { + qrange = <128 32>; + accumulator = <0 36 16 2 50>; + interrupts = <0 215 0xf01>; + multi-queue; + qalloc-by-id; + }; + acc-1 { + qrange = <160 32>; + accumulator = <0 37 16 2 50>; + interrupts = <0 216 0xf01>; + multi-queue; + }; + acc-2 { + qrange = <192 32>; + accumulator = <0 38 16 2 50>; + interrupts = <0 217 0xf01>; + multi-queue; + }; + acc-3 { + qrange = <224 32>; + accumulator = <0 39 16 2 50>; + interrupts = <0 218 0xf01>; + multi-queue; + }; + }; + }; + descriptor-regions { + #address-cells = <1>; + #size-cells = <1>; + ranges; + region-12 { + id = <12>; + region-spec = <8192 128>; /* num_desc desc_size */ + link-index = <0x4000>; + }; + }; + pdsps { + #address-cells = <1>; + #size-cells = <1>; + ranges; + pdsp0@0x2a10000 { + firmware = "keystone/qmss_pdsp_acc48_k2_le_1_0_0_8.fw"; + reg = <0x2a10000 0x1000>, + <0x2a0f000 0x100>, + <0x2a0c000 0x3c8>, + <0x2a20000 0x4000>; + id = <0>; + }; + }; +}; /* qmss */ diff --git a/Documentation/devicetree/bindings/sound/adi,ssm2602.txt b/Documentation/devicetree/bindings/sound/adi,ssm2602.txt new file mode 100644 index 000000000000..3b3302fe399b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,ssm2602.txt @@ -0,0 +1,19 @@ +Analog Devices SSM2602, SSM2603 and SSM2604 I2S audio CODEC devices + +SSM2602 support both I2C and SPI as the configuration interface, +the selection is made by the MODE strap-in pin. +SSM2603 and SSM2604 only support I2C as the configuration interface. + +Required properties: + + - compatible : One of "adi,ssm2602", "adi,ssm2603" or "adi,ssm2604" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + + Example: + + ssm2602: ssm2602@1a { + compatible = "adi,ssm2602"; + reg = <0x1a>; + }; diff --git a/Documentation/devicetree/bindings/sound/arndale.txt b/Documentation/devicetree/bindings/sound/arndale.txt new file mode 100644 index 000000000000..0e76946385ae --- /dev/null +++ b/Documentation/devicetree/bindings/sound/arndale.txt @@ -0,0 +1,24 @@ +Audio Binding for Arndale boards + +Required properties: +- compatible : Can be the following, + "samsung,arndale-rt5631" + +- samsung,audio-cpu: The phandle of the Samsung I2S controller +- samsung,audio-codec: The phandle of the audio codec + +Optional: +- samsung,model: The name of the sound-card + +Arndale Boards has many audio daughter cards, one of them is +rt5631/alc5631. Below example shows audio bindings for rt5631/ +alc5631 based codec. + +Example: + +sound { + compatible = "samsung,arndale-rt5631"; + + samsung,audio-cpu = <&i2s0> + samsung,audio-codec = <&rt5631>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs35l32.txt b/Documentation/devicetree/bindings/sound/cs35l32.txt new file mode 100644 index 000000000000..1417d3f5cc22 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l32.txt @@ -0,0 +1,62 @@ +CS35L32 audio CODEC + +Required properties: + + - compatible : "cirrus,cs35l32" + + - reg : the I2C address of the device for I2C. Address is determined by the level + of the AD0 pin. Level 0 is 0x40 while Level 1 is 0x41. + + - VA-supply, VP-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - cirrus,boost-manager : Boost voltage control. + 0 = Automatically managed. Boost-converter output voltage is the higher + of the two: Class G or adaptive LED voltage. + 1 = Automatically managed irrespective of audio, adapting for low-power + dissipation when LEDs are ON, and operating in Fixed-Boost Bypass Mode + if LEDs are OFF (VBST = VP). + 2 = (Default) Boost voltage fixed in Bypass Mode (VBST = VP). + 3 = Boost voltage fixed at 5 V. + + - cirrus,sdout-datacfg : Data configuration for dual CS35L32 applications only. + Determines the data packed in a two-CS35L32 configuration. + 0 = Left/right channels VMON[11:0], IMON[11:0], VPMON[7:0]. + 1 = Left/right channels VMON[11:0], IMON[11:0], STATUS. + 2 = (Default) left/right channels VMON[15:0], IMON [15:0]. + 3 = Left/right channels VPMON[7:0], STATUS. + + - cirrus,sdout-share : SDOUT sharing. Determines whether one or two CS35L32 + devices are on board sharing SDOUT. + 0 = (Default) One IC. + 1 = Two IC's. + + - cirrus,battery-recovery : Low battery nominal recovery threshold, rising VP. + 0 = 3.1V + 1 = 3.2V + 2 = 3.3V (Default) + 3 = 3.4V + + - cirrus,battery-threshold : Low battery nominal threshold, falling VP. + 0 = 3.1V + 1 = 3.2V + 2 = 3.3V + 3 = 3.4V (Default) + 4 = 3.5V + 5 = 3.6V + +Example: + +codec: codec@40 { + compatible = "cirrus,cs35l32"; + reg = <0x40>; + reset-gpios = <&gpio 10 0>; + cirrus,boost-manager = <0x03>; + cirrus,sdout-datacfg = <0x02>; + VA-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 60ca07996458..46bc9829c71a 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -32,7 +32,7 @@ Optional properties: - rx-num-evt : FIFO levels. - sram-size-playback : size of sram to be allocated during playback - sram-size-capture : size of sram to be allocated during capture -- interrupts : Interrupt numbers for McASP, currently not used by the driver +- interrupts : Interrupt numbers for McASP - interrupt-names : Known interrupt names are "tx" and "rx" - pinctrl-0: Should specify pin control group used for this controller. - pinctrl-names: Should contain only one value - "default", for more details diff --git a/Documentation/devicetree/bindings/sound/es8328.txt b/Documentation/devicetree/bindings/sound/es8328.txt new file mode 100644 index 000000000000..30ea8a318ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/es8328.txt @@ -0,0 +1,38 @@ +Everest ES8328 audio CODEC + +This device supports both I2C and SPI. + +Required properties: + + - compatible : "everest,es8328" + - DVDD-supply : Regulator providing digital core supply voltage 1.8 - 3.6V + - AVDD-supply : Regulator providing analog supply voltage 3.3V + - PVDD-supply : Regulator providing digital IO supply voltage 1.8 - 3.6V + - IPVDD-supply : Regulator providing analog output voltage 3.3V + - clocks : A 22.5792 or 11.2896 MHz clock + - reg : the I2C address of the device for I2C, the chip select number for SPI + +Pins on the device (for linking into audio routes): + + * LOUT1 + * LOUT2 + * ROUT1 + * ROUT2 + * LINPUT1 + * RINPUT1 + * LINPUT2 + * RINPUT2 + * Mic Bias + + +Example: + +codec: es8328@11 { + compatible = "everest,es8328"; + DVDD-supply = <®_3p3v>; + AVDD-supply = <®_3p3v>; + PVDD-supply = <®_3p3v>; + HPVDD-supply = <®_3p3v>; + clocks = <&clks 169>; + reg = <0x11>; +}; diff --git a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt index 0d7985c864af..6dfa88c4dc1e 100644 --- a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt +++ b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt @@ -1,11 +1,16 @@ Audio complex for Eukrea boards with tlv320aic23 codec. Required properties: -- compatible : "eukrea,asoc-tlv320" -- eukrea,model : The user-visible name of this sound complex. -- ssi-controller : The phandle of the SSI controller. -- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX). -- fsl,mux-ext-port : The external port of the i.MX audio muxer. + + - compatible : "eukrea,asoc-tlv320" + + - eukrea,model : The user-visible name of this sound complex. + + - ssi-controller : The phandle of the SSI controller. + + - fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX). + + - fsl,mux-ext-port : The external port of the i.MX audio muxer. Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index aeb8c4a0b88d..d3b6b5f48010 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -7,36 +7,39 @@ other DSPs. It has up to six transmitters and four receivers. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-esai". + - compatible : Compatible list, must contain "fsl,imx35-esai" or + "fsl,vf610-esai" - - reg : Offset and length of the register set for the device. + - reg : Offset and length of the register set for the device. - - interrupts : Contains the spdif interrupt. + - interrupts : Contains the spdif interrupt. - - dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. - - dma-names : Two dmas have to be defined, "tx" and "rx". + - dma-names : Two dmas have to be defined, "tx" and "rx". - - clocks: Contains an entry for each entry in clock-names. + - clocks : Contains an entry for each entry in clock-names. - - clock-names : Includes the following entries: - "core" The core clock used to access registers - "extal" The esai baud clock for esai controller used to derive - HCK, SCK and FS. - "fsys" The system clock derived from ahb clock used to derive - HCK, SCK and FS. + - clock-names : Includes the following entries: + "core" The core clock used to access registers + "extal" The esai baud clock for esai controller used to + derive HCK, SCK and FS. + "fsys" The system clock derived from ahb clock used to + derive HCK, SCK and FS. - - fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for TFCR[TFWM] or RFCR[RFWM]. + - fsl,fifo-depth : The number of elements in the transmit and receive + FIFOs. This number is the maximum allowed value for + TFCR[TFWM] or RFCR[RFWM]. - fsl,esai-synchronous: This is a boolean property. If present, indicating - that ESAI would work in the synchronous mode, which means all the settings - for Receiving would be duplicated from Transmition related registers. + that ESAI would work in the synchronous mode, which + means all the settings for Receiving would be + duplicated from Transmition related registers. - - big-endian : If this property is absent, the native endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. + - big-endian : If this property is absent, the native endian mode + will be in use as default, or the big endian mode + will be in use for all the device registers. Example: diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index 3e9e82c8eab3..b5ee32ee3706 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -6,32 +6,31 @@ a fibre cable. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-spdif". + - compatible : Compatible list, must contain "fsl,imx35-spdif". - - reg : Offset and length of the register set for the device. + - reg : Offset and length of the register set for the device. - - interrupts : Contains the spdif interrupt. + - interrupts : Contains the spdif interrupt. - - dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. - - dma-names : Two dmas have to be defined, "tx" and "rx". + - dma-names : Two dmas have to be defined, "tx" and "rx". - - clocks : Contains an entry for each entry in clock-names. + - clocks : Contains an entry for each entry in clock-names. - - clock-names : Includes the following entries: - "core" The core clock of spdif controller - "rxtx<0-7>" Clock source list for tx and rx clock. - This clock list should be identical to - the source list connecting to the spdif - clock mux in "SPDIF Transceiver Clock - Diagram" of SoC reference manual. It - can also be referred to TxClk_Source - bit of register SPDIF_STC. + - clock-names : Includes the following entries: + "core" The core clock of spdif controller. + "rxtx<0-7>" Clock source list for tx and rx clock. + This clock list should be identical to the source + list connecting to the spdif clock mux in "SPDIF + Transceiver Clock Diagram" of SoC reference manual. + It can also be referred to TxClk_Source bit of + register SPDIF_STC. - - big-endian : If this property is absent, the native endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. + - big-endian : If this property is absent, the native endian mode + will be in use as default, or the big endian mode + will be in use for all the device registers. Example: diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt index 3aa4a8f528f4..5b76be45d18b 100644 --- a/Documentation/devicetree/bindings/sound/fsl,ssi.txt +++ b/Documentation/devicetree/bindings/sound/fsl,ssi.txt @@ -58,13 +58,7 @@ Optional properties: Documentation/devicetree/bindings/dma/dma.txt. - dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq is not defined. -- fsl,mode: The operating mode for the SSI interface. - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master +- fsl,mode: The operating mode for the AC97 interface only. "ac97-slave" - AC97 mode, SSI is clock slave "ac97-master" - AC97 mode, SSI is clock master diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt new file mode 100644 index 000000000000..a96774c194c8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -0,0 +1,82 @@ +Freescale Generic ASoC Sound Card with ASRC support + +The Freescale Generic ASoC Sound Card can be used, ideally, for all Freescale +SoCs connecting with external CODECs. + +The idea of this generic sound card is a bit like ASoC Simple Card. However, +for Freescale SoCs (especially those released in recent years), most of them +have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And +this is a specific feature that might be painstakingly controlled and merged +into the Simple Card. + +So having this generic sound card allows all Freescale SoC users to benefit +from the simplification of a new card support and the capability of the wide +sample rates support through ASRC. + +Note: The card is initially designed for those sound cards who use I2S and + PCM DAI formats. However, it'll be also possible to support those non + I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long + as the driver has been properly upgraded. + + +The compatible list for this generic sound card currently: + "fsl,imx-audio-cs42888" + + "fsl,imx-audio-wm8962" + (compatible with Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt) + + "fsl,imx-audio-sgtl5000" + (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt) + +Required properties: + + - compatible : Contains one of entries in the compatible list. + + - model : The user-visible name of this sound complex + + - audio-cpu : The phandle of an CPU DAI controller + + - audio-codec : The phandle of an audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. There're a few pre-designed board connectors: + * Line Out Jack + * Line In Jack + * Headphone Jack + * Mic Jack + * Ext Spk + * AMIC (stands for Analog Microphone Jack) + * DMIC (stands for Digital Microphone Jack) + + Note: The "Mic Jack" and "AMIC" are redundant while + coexsiting in order to support the old bindings + of wm8962 and sgtl5000. + +Optional properties: + + - audio-asrc : The phandle of ASRC. It can be absent if there's no + need to add ASRC support via DPCM. + +Example: +sound-cs42888 { + compatible = "fsl,imx-audio-cs42888"; + model = "cs42888-audio"; + audio-cpu = <&esai>; + audio-asrc = <&asrc>; + audio-codec = <&cs42888>; + audio-routing = + "Line Out Jack", "AOUT1L", + "Line Out Jack", "AOUT1R", + "Line Out Jack", "AOUT2L", + "Line Out Jack", "AOUT2R", + "Line Out Jack", "AOUT3L", + "Line Out Jack", "AOUT3R", + "Line Out Jack", "AOUT4L", + "Line Out Jack", "AOUT4R", + "AIN1L", "Line In Jack", + "AIN1R", "Line In Jack", + "AIN2L", "Line In Jack", + "AIN2R", "Line In Jack"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 0f4e23828190..044e5d76e2dd 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -5,25 +5,55 @@ which provides a synchronous audio interface that supports fullduplex serial interfaces with frame synchronization such as I2S, AC97, TDM, and codec/DSP interfaces. - Required properties: -- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai". -- reg: Offset and length of the register set for the device. -- clocks: Must contain an entry for each entry in clock-names. -- clock-names : Must include the "bus" for register access and "mclk1" "mclk2" - "mclk3" for bit clock and frame clock providing. -- dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. -- dma-names : Two dmas have to be defined, "tx" and "rx". -- pinctrl-names: Must contain a "default" entry. -- pinctrl-NNN: One property must exist for each entry in pinctrl-names. - See ../pinctrl/pinctrl-bindings.txt for details of the property values. -- big-endian-regs: If this property is absent, the little endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. -- big-endian-data: If this property is absent, the little endian mode will - be in use as default, or the big endian mode will be in use for all the - fifo data. + + - compatible : Compatible list, contains "fsl,vf610-sai" or + "fsl,imx6sx-sai". + + - reg : Offset and length of the register set for the device. + + - clocks : Must contain an entry for each entry in clock-names. + + - clock-names : Must include the "bus" for register access and + "mclk1", "mclk2", "mclk3" for bit clock and frame + clock providing. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Two dmas have to be defined, "tx" and "rx". + + - pinctrl-names : Must contain a "default" entry. + + - pinctrl-NNN : One property must exist for each entry in + pinctrl-names. See ../pinctrl/pinctrl-bindings.txt + for details of the property values. + + - big-endian : Boolean property, required if all the FTM_PWM + registers are big-endian rather than little-endian. + + - lsb-first : Configures whether the LSB or the MSB is transmitted + first for the fifo data. If this property is absent, + the MSB is transmitted first as default, or the LSB + is transmitted first. + + - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating + that SAI will work in the synchronous mode (sync Tx + with Rx) which means both the transimitter and the + receiver will send and receive data by following + receiver's bit clocks and frame sync clocks. + + - fsl,sai-asynchronous: This is a boolean property. If present, indicating + that SAI will work in the asynchronous mode, which + means both transimitter and receiver will send and + receive data by following their own bit clocks and + frame sync clocks separately. + +Note: +- If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the + default synchronous mode (sync Rx with Tx) will be used, which means both + transimitter and receiver will send and receive data by following clocks + of transimitter. +- fsl,sai-asynchronous and fsl,sai-synchronous-rx are exclusive. Example: sai2: sai@40031000 { @@ -38,6 +68,6 @@ sai2: sai@40031000 { dma-names = "tx", "rx"; dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>, <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>; - big-endian-regs; - big-endian-data; + big-endian; + lsb-first; }; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt new file mode 100644 index 000000000000..07b68ab206fb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt @@ -0,0 +1,60 @@ +Freescale i.MX audio complex with ES8328 codec + +Required properties: +- compatible : "fsl,imx-audio-es8328" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- jack-gpio : Optional GPIO for headphone jack +- audio-amp-supply : Power regulator for speaker amps +- audio-codec : The phandle of the ES8328 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, ES8328 + pins, and the jacks on the board: + + Power supplies: + * audio-amp + + ES8328 pins: + * LOUT1 + * LOUT2 + * ROUT1 + * ROUT2 + * LINPUT1 + * LINPUT2 + * RINPUT1 + * RINPUT2 + * Mic PGA + + Board connectors: + * Headphone + * Speaker + * Mic Jack +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer (AUDMIX) + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + jack-gpio = <&gpio5 15 0>; + audio-amp-supply = <®_audio_amp>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1", + "LINPUT1", "Mic Jack", + "RINPUT1", "Mic Jack", + "Mic Jack", "Mic Bias"; + mux-int-port = <1>; + mux-ext-port = <3>; +}; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt b/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt index e4acdd891e49..2f89db88fd57 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt @@ -1,33 +1,40 @@ Freescale i.MX audio complex with SGTL5000 codec Required properties: -- compatible : "fsl,imx-audio-sgtl5000" -- model : The user-visible name of this sound complex -- ssi-controller : The phandle of the i.MX SSI controller -- audio-codec : The phandle of the SGTL5000 audio codec -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names could be power - supplies, SGTL5000 pins, and the jacks on the board: - - Power supplies: - * Mic Bias - - SGTL5000 pins: - * MIC_IN - * LINE_IN - * HP_OUT - * LINE_OUT - - Board connectors: - * Mic Jack - * Line In Jack - * Headphone Jack - * Line Out Jack - * Ext Spk - -- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) -- mux-ext-port : The external port of the i.MX audio muxer + + - compatible : "fsl,imx-audio-sgtl5000" + + - model : The user-visible name of this sound complex + + - ssi-controller : The phandle of the i.MX SSI controller + + - audio-codec : The phandle of the SGTL5000 audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, SGTL5000 + pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + SGTL5000 pins: + * MIC_IN + * LINE_IN + * HP_OUT + * LINE_OUT + + Board connectors: + * Mic Jack + * Line In Jack + * Headphone Jack + * Line Out Jack + * Ext Spk + + - mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) + + - mux-ext-port : The external port of the i.MX audio muxer Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt b/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt index 7d13479f9c3c..da84a442ccea 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt @@ -2,23 +2,25 @@ Freescale i.MX audio complex with S/PDIF transceiver Required properties: - - compatible : "fsl,imx-audio-spdif" + - compatible : "fsl,imx-audio-spdif" - - model : The user-visible name of this sound complex + - model : The user-visible name of this sound complex - - spdif-controller : The phandle of the i.MX S/PDIF controller + - spdif-controller : The phandle of the i.MX S/PDIF controller Optional properties: - - spdif-out : This is a boolean property. If present, the transmitting - function of S/PDIF will be enabled, indicating there's a physical - S/PDIF out connector/jack on the board or it's connecting to some - other IP block, such as an HDMI encoder/display-controller. + - spdif-out : This is a boolean property. If present, the + transmitting function of S/PDIF will be enabled, + indicating there's a physical S/PDIF out connector + or jack on the board or it's connecting to some + other IP block, such as an HDMI encoder or + display-controller. - - spdif-in : This is a boolean property. If present, the receiving - function of S/PDIF will be enabled, indicating there's a physical - S/PDIF in connector/jack on the board. + - spdif-in : This is a boolean property. If present, the receiving + function of S/PDIF will be enabled, indicating there + is a physical S/PDIF in connector/jack on the board. * Note: At least one of these two properties should be set in the DT binding. diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt index f49450a87890..acea71bee34f 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -1,25 +1,32 @@ Freescale i.MX audio complex with WM8962 codec Required properties: -- compatible : "fsl,imx-audio-wm8962" -- model : The user-visible name of this sound complex -- ssi-controller : The phandle of the i.MX SSI controller -- audio-codec : The phandle of the WM8962 audio codec -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names could be power - supplies, WM8962 pins, and the jacks on the board: - - Power supplies: - * Mic Bias - - Board connectors: - * Mic Jack - * Headphone Jack - * Ext Spk - -- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) -- mux-ext-port : The external port of the i.MX audio muxer + + - compatible : "fsl,imx-audio-wm8962" + + - model : The user-visible name of this sound complex + + - ssi-controller : The phandle of the i.MX SSI controller + + - audio-codec : The phandle of the WM8962 audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, WM8962 + pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + + - mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) + + - mux-ext-port : The external port of the i.MX audio muxer Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt index f88a00e54c63..b30a737e209e 100644 --- a/Documentation/devicetree/bindings/sound/imx-audmux.txt +++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt @@ -1,18 +1,24 @@ Freescale Digital Audio Mux (AUDMUX) device Required properties: -- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21, - or "fsl,imx31-audmux" for the version firstly used on i.MX31. -- reg : Should contain AUDMUX registers location and length + + - compatible : "fsl,imx21-audmux" for AUDMUX version firstly used + on i.MX21, or "fsl,imx31-audmux" for the version + firstly used on i.MX31. + + - reg : Should contain AUDMUX registers location and length. An initial configuration can be setup using child nodes. Required properties of optional child nodes: -- fsl,audmux-port : Integer of the audmux port that is configured by this - child node. -- fsl,port-config : List of configuration options for the specific port. For - imx31-audmux and above, it is a list of tuples <ptcr pdcr>. For - imx21-audmux it is a list of pcr values. + + - fsl,audmux-port : Integer of the audmux port that is configured by this + child node. + + - fsl,port-config : List of configuration options for the specific port. + For imx31-audmux and above, it is a list of tuples + <ptcr pdcr>. For imx21-audmux it is a list of pcr + values. Example: diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index c454e67f54bb..aa802a274520 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -16,6 +16,8 @@ Optional properties: - clock-names: Should be "mclk" +- maxim,dmic-freq: Frequency at which to clock DMIC + Pins on the device (for linking into audio routes): * MIC1 diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt index 9c7c55c71370..c949abc2992f 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt @@ -25,6 +25,7 @@ Required properties: Optional properties: - nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in +- nvidia,mic-det-gpios : The GPIO that detect microphones are plugged in Example: diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt index c5be003f413e..0d0ab51105b0 100644 --- a/Documentation/devicetree/bindings/sound/renesas,fsi.txt +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -1,11 +1,16 @@ Renesas FSI Required properties: -- compatible : "renesas,sh_fsi2" or "renesas,sh_fsi" +- compatible : "renesas,fsi2-<soctype>", + "renesas,sh_fsi2" or "renesas,sh_fsi" as + fallback. + Examples with soctypes are: + - "renesas,fsi2-r8a7740" (R-Mobile A1) + - "renesas,fsi2-sh73a0" (SH-Mobile AG5) - reg : Should contain the register physical address and length - interrupts : Should contain FSI interrupt -- fsia,spdif-connection : FSI is connected by S/PDFI +- fsia,spdif-connection : FSI is connected by S/PDIF - fsia,stream-mode-support : FSI supports 16bit stream mode. - fsia,use-internal-clock : FSI uses internal clock when master mode. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index aa697abf337e..2dd690bc19cc 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -1,8 +1,12 @@ Renesas R-Car sound Required properties: -- compatible : "renesas,rcar_sound-gen1" if generation1 +- compatible : "renesas,rcar_sound-<soctype>", fallbacks + "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 + Examples with soctypes are: + - "renesas,rcar_sound-r8a7790" (R-Car H2) + - "renesas,rcar_sound-r8a7791" (R-Car M2-W) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 @@ -35,9 +39,9 @@ DAI subnode properties: Example: -rcar_sound: rcar_sound@0xffd90000 { +rcar_sound: rcar_sound@ec500000 { #sound-dai-cells = <1>; - compatible = "renesas,rcar_sound-gen2"; + compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2"; reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ diff --git a/Documentation/devicetree/bindings/sound/rt5631.txt b/Documentation/devicetree/bindings/sound/rt5631.txt new file mode 100644 index 000000000000..92b986ca337b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5631.txt @@ -0,0 +1,48 @@ +ALC5631/RT5631 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "realtek,alc5631" or "realtek,rt5631" + + - reg : the I2C address of the device. + +Pins on the device (for linking into audio routes): + + * SPK_OUT_R_P + * SPK_OUT_R_N + * SPK_OUT_L_P + * SPK_OUT_L_N + * HP_OUT_L + * HP_OUT_R + * AUX_OUT2_LP + * AUX_OUT2_RN + * AUX_OUT1_LP + * AUX_OUT1_RN + * AUX_IN_L_JD + * AUX_IN_R_JD + * MONO_IN_P + * MONO_IN_N + * MIC1_P + * MIC1_N + * MIC2_P + * MIC2_N + * MONO_OUT_P + * MONO_OUT_N + * MICBIAS1 + * MICBIAS2 + +Example: + +alc5631: alc5631@1a { + compatible = "realtek,alc5631"; + reg = <0x1a>; +}; + +or + +rt5631: rt5631@1a { + compatible = "realtek,rt5631"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5677.txt b/Documentation/devicetree/bindings/sound/rt5677.txt new file mode 100644 index 000000000000..740ff771aa8b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5677.txt @@ -0,0 +1,76 @@ +RT5677 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5677". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +- gpio-controller : Indicates this device is a GPIO controller. + +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Optional properties: + +- realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin. + +- realtek,in1-differential +- realtek,in2-differential +- realtek,lout1-differential +- realtek,lout2-differential +- realtek,lout3-differential + Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential, + rather than single-ended. + +- realtek,gpio-config + Array of six 8bit elements that configures GPIO. + 0 - floating (reset value) + 1 - pull down + 2 - pull up + +- realtek,jd1-gpio + Configures GPIO Mic Jack detection 1. + Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively. + +- realtek,jd2-gpio +- realtek,jd3-gpio + Configures GPIO Mic Jack detection 2 and 3. + Select 0 ~ 3 as OFF, GPIO4, GPIO5 and GPIO6 respectively. + +Pins on the device (for linking into audio routes): + + * IN1P + * IN1N + * IN2P + * IN2N + * MICBIAS1 + * DMIC1 + * DMIC2 + * DMIC3 + * DMIC4 + * LOUT1 + * LOUT2 + * LOUT3 + +Example: + +rt5677 { + compatible = "realtek,rt5677"; + reg = <0x2c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + realtek,pow-ldo2-gpio = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; + realtek,in1-differential = "true"; + realtek,gpio-config = /bits/ 8 <0 0 0 0 0 2>; /* pull up GPIO6 */ + realtek,jd2-gpio = <3>; /* Enables Jack detection for GPIO6 */ +}; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index 7386d444ada1..d188296bb6ec 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -6,10 +6,17 @@ Required SoC Specific Properties: - samsung,s3c6410-i2s: for 8/16/24bit stereo I2S. - samsung,s5pv210-i2s: for 8/16/24bit multichannel(5.1) I2S with secondary fifo, s/w reset control and internal mux for root clk src. - - samsung,exynos5420-i2s: for 8/16/24bit multichannel(7.1) I2S with - secondary fifo, s/w reset control, internal mux for root clk src and - TDM support. TDM (Time division multiplexing) is to allow transfer of - multiple channel audio data on single data line. + - samsung,exynos5420-i2s: for 8/16/24bit multichannel(5.1) I2S for + playback, sterio channel capture, secondary fifo using internal + or external dma, s/w reset control, internal mux for root clk src + and 7.1 channel TDM support for playback. TDM (Time division multiplexing) + is to allow transfer of multiple channel audio data on single data line. + - samsung,exynos7-i2s: with all the available features of exynos5 i2s, + exynos7 I2S has 7.1 channel TDM support for capture, secondary fifo + with only external dma and more no.of root clk sampling frequencies. + - samsung,exynos7-i2s1: I2S1 on previous samsung platforms supports + stereo channels. exynos7 i2s1 upgraded to 5.1 multichannel with + slightly modified bit offsets. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 955df60a118c..0e5e4eb3ef1b 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -7,10 +7,33 @@ Required properties: - clocks : the clock provider of SYS_MCLK +- micbias-resistor-k-ohms : the bias resistor to be used in kOmhs + The resistor can take values of 2k, 4k or 8k. + If set to 0 it will be off. + If this node is not mentioned or if the value is unknown, then + micbias resistor is set to 4K. + +- micbias-voltage-m-volts : the bias voltage to be used in mVolts + The voltage can take values from 1.25V to 3V by 250mV steps + If this node is not mentionned or the value is unknown, then + the value is set to 1.25V. + +- VDDA-supply : the regulator provider of VDDA + +- VDDIO-supply: the regulator provider of VDDIO + +Optional properties: + +- VDDD-supply : the regulator provider of VDDD + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; clocks = <&clks 150>; + micbias-resistor-k-ohms = <2>; + micbias-voltage-m-volts = <2250>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; }; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index c2e9841dfce4..c3cba600bf11 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -17,6 +17,10 @@ Optional properties: source. - simple-audio-card,mclk-fs : Multiplication factor between stream rate and codec mclk. +- simple-audio-card,hp-det-gpio : Reference to GPIO that signals when + headphones are attached. +- simple-audio-card,mic-det-gpio : Reference to GPIO that signals when + a microphone is attached. Optional subnodes: diff --git a/Documentation/devicetree/bindings/sound/ssm4567.txt b/Documentation/devicetree/bindings/sound/ssm4567.txt new file mode 100644 index 000000000000..ec3d9e7004b5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ssm4567.txt @@ -0,0 +1,15 @@ +Analog Devices SSM4567 audio amplifier + +This device supports I2C only. + +Required properties: + - compatible : Must be "adi,ssm4567" + - reg : the I2C address of the device. This will either be 0x34 (LR_SEL/ADDR connected to AGND), + 0x35 (LR_SEL/ADDR connected to IOVDD) or 0x36 (LR_SEL/ADDR open). + +Example: + + ssm4567: ssm4567@34 { + compatible = "adi,ssm4567"; + reg = <0x34>; + }; diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt index b7e71bf5caf4..307398ef2317 100644 --- a/Documentation/devicetree/bindings/sound/st,sta350.txt +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -33,7 +33,7 @@ Optional properties: 0: Channel 1 1: Channel 2 2: Channel 3 - If parameter is missing, channel 1 is choosen. + If parameter is missing, channel 1 is chosen. This properties have to be specified as '/bits/ 8' values. - st,thermal-warning-recover: diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt new file mode 100644 index 000000000000..e8bf23eb1803 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -0,0 +1,26 @@ +Texas Instruments TS3A227E +Autonomous Audio Accessory Detection and Configuration Switch + +The TS3A227E detect headsets of 3-ring and 4-ring standards and +switches automatically to route the microphone correctly. It also +handles key press detection in accordance with the Android audio +headset specification v1.0. + +Required properties: + + - compatible: Should contain "ti,ts3a227e". + - reg: The i2c address. Should contain <0x3b>. + - interrupt-parent: The parent interrupt controller + - interrupts: Interrupt number for /INT pin from the 227e + + +Examples: + + i2c { + ts3a227e@3b { + compatible = "ti,ts3a227e"; + reg = <0x3b>; + interrupt-parent = <&gpio>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/wm8960.txt b/Documentation/devicetree/bindings/sound/wm8960.txt new file mode 100644 index 000000000000..2deb8a3da9c5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8960.txt @@ -0,0 +1,31 @@ +WM8960 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8960" + + - reg : the I2C address of the device. + +Optional properties: + - wlf,shared-lrclk: This is a boolean property. If present, the LRCM bit of + R24 (Additional control 2) gets set, indicating that ADCLRC and DACLRC pins + will be disabled only when ADC (Left and Right) and DAC (Left and Right) + are disabled. + When wm8960 works on synchronize mode and DACLRC pin is used to supply + frame clock, it will no frame clock for captrue unless enable DAC to enable + DACLRC pin. If shared-lrclk is present, no need to enable DAC for captrue. + + - wlf,capless: This is a boolean property. If present, OUT3 pin will be + enabled and disabled together with HP_L and HP_R pins in response to jack + detect events. + +Example: + +codec: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + + wlf,shared-lrclk; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 4256a6df9b79..aad527b357a0 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -7,6 +7,9 @@ Required properties: - interrupts : Should contain CSPI/eCSPI interrupt - fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. Example: @@ -19,4 +22,6 @@ ecspi@70010000 { fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ <&gpio3 25 0>; /* GPIO3_25 */ + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; + dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index f24baf3b6cc1..d11c3721e7cd 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -6,8 +6,17 @@ Required properties: "renesas,sh-mobile-msiof" for SH Mobile series. Examples with soctypes are: "renesas,msiof-r8a7790" (R-Car H2) - "renesas,msiof-r8a7791" (R-Car M2) -- reg : Offset and length of the register set for the device + "renesas,msiof-r8a7791" (R-Car M2-W) + "renesas,msiof-r8a7792" (R-Car V2H) + "renesas,msiof-r8a7793" (R-Car M2-N) + "renesas,msiof-r8a7794" (R-Car E2) +- reg : A list of offsets and lengths of the register sets for + the device. + If only one register set is present, it is to be used + by both the CPU and the DMA engine. + If two register sets are present, the first is to be + used by the CPU, and the second is to be used by the + DMA engine. - interrupt-parent : The phandle for the interrupt controller that services interrupts for this device - interrupts : Interrupt specifier @@ -17,12 +26,16 @@ Required properties: Optional properties: - clocks : Must contain a reference to the functional clock. - num-cs : Total number of chip-selects (default is 1) +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words (default is 64) - renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64, or 256 on R-Car H2 and M2) + (default is 64, or 256 on R-Car Gen2) Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. @@ -31,9 +44,11 @@ Example: msiof0: spi@e6e20000 { compatible = "renesas,msiof-r8a7791"; - reg = <0 0xe6e20000 0 0x0064>; + reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; + dmas = <&dmac0 0x51>, <&dmac0 0x52>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index f80887bca0d6..12ecfe9e3599 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -1,5 +1,10 @@ Davinci SPI controller device bindings +Links on DM: +Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf +dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf +OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf + Required properties: - #address-cells: number of cells required to define a chip select address on the SPI bus. Should be set to 1. @@ -24,6 +29,30 @@ Optional: cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; where first three are internal CS and last two are GPIO CS. +Optional properties for slave devices: +SPI slave nodes can contain the following properties. +Not all SPI Peripherals from Texas Instruments support this. +Please check SPI peripheral documentation for a device before using these. + +- ti,spi-wdelay : delay between transmission of words + (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module + clock periods. + + delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period + +Below is timing diagram which shows functional meaning of +"ti,spi-wdelay" parameter. + + +-+ +-+ +-+ +-+ +-+ +-+ +-+ +-+ +SPI_CLK | | | | | | | | | | | | | | | | + +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +- + +SPI_SOMI/SIMO+-----------------+ +----------- + +----------+ word1 +---------------------------+word2 + +-----------------+ +----------- + WDELAY + <--------------------------> + Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus. @@ -43,6 +72,7 @@ spi0:spi@20BF0000 { compatible = "st,m25p32"; spi-max-frequency = <25000000>; reg = <0>; + ti,spi-wdelay = <8>; partition@0 { label = "u-boot-spl"; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index 5376de40f10b..cbbe16ed3874 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -10,7 +10,12 @@ Required properties: - pinctrl-names: must contain a "default" entry. - spi-num-chipselects : the number of the chipselect signals. - bus-num : the slave chip chipselect signal number. -- big-endian : if DSPI modudle is big endian, the bool will be set in node. + +Optional property: +- big-endian: If present the dspi device's registers are implemented + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + Example: dspi0@4002c000 { diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt index 8a824be15754..a95603bcf6ff 100644 --- a/Documentation/devicetree/bindings/spi/spi-gpio.txt +++ b/Documentation/devicetree/bindings/spi/spi-gpio.txt @@ -8,8 +8,10 @@ Required properties: - gpio-sck: GPIO spec for the SCK line to use - gpio-miso: GPIO spec for the MISO line to use - gpio-mosi: GPIO spec for the MOSI line to use - - cs-gpios: GPIOs to use for chipselect lines - - num-chipselects: number of chipselect lines + - cs-gpios: GPIOs to use for chipselect lines. + Not needed if num-chipselects = <0>. + - num-chipselects: Number of chipselect lines. Should be <0> if a single device + with no chip select is connected. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt new file mode 100644 index 000000000000..c7dd50fb8eb2 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt @@ -0,0 +1,37 @@ +IMG Synchronous Peripheral Flash Interface (SPFI) controller + +Required properties: +- compatible: Must be "img,spfi". +- reg: Must contain the base address and length of the SPFI registers. +- interrupts: Must contain the SPFI interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - spfi: SPI operating clock + - sys: SPI system interface clock +- dmas: Must contain an entry for each entry in dma-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx +- #address-cells: Must be 1. +- #size-cells: Must be 0. + +Optional properties: +- img,supports-quad-mode: Should be set if the interface supports quad mode + SPI transfers. + +Example: + +spi@18100f00 { + compatible = "img,spfi"; + reg = <0x18100f00 0x100>; + interrupts = <GIC_SHARED 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&spi_clk>, <&system_clk>; + clock-names = "spfi", "sys"; + dmas = <&mdc 9 0xffffffff 0>, <&mdc 10 0xffffffff 0>; + dma-names = "rx", "tx"; + + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt new file mode 100644 index 000000000000..bb52a86f3365 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -0,0 +1,22 @@ +Amlogic Meson SPI controllers + +* SPIFC (SPI Flash Controller) + +The Meson SPIFC is a controller optimized for communication with SPI +NOR memories, without DMA support and a 64-byte unified transmit / +receive buffer. + +Required properties: + - compatible: should be "amlogic,meson6-spifc" + - reg: physical base address and length of the controller registers + - clocks: phandle of the input clock for the baud rate generator + - #address-cells: should be 1 + - #size-cells: should be 0 + + spi@c1108c80 { + compatible = "amlogic,meson6-spifc"; + reg = <0xc1108c80 0x80>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index a3ff50fc76fb..50c3a3de61c1 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -1,7 +1,7 @@ Marvell Orion SPI device Required properties: -- compatible : should be "marvell,orion-spi". +- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi". - reg : offset and length of the register set for the device - cell-index : Which of multiple SPI controllers is this. Optional properties: diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index d57d82a74054..8f4169f63936 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -11,7 +11,10 @@ Required properties: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) - "renesas,qspi-r8a7790" (R-Car H2) - - "renesas,qspi-r8a7791" (R-Car M2) + - "renesas,qspi-r8a7791" (R-Car M2-W) + - "renesas,qspi-r8a7792" (R-Car V2H) + - "renesas,qspi-r8a7793" (R-Car M2-N) + - "renesas,qspi-r8a7794" (R-Car E2) - reg : Address start and address range size of the device - interrupts : A list of interrupt-specifiers, one for each entry in interrupt-names. @@ -30,6 +33,9 @@ Required properties: Optional properties: - clocks : Must contain a reference to the functional clock. +- dmas : Must contain a list of two references to DMA specifiers, + one for transmission, and one for reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. @@ -58,4 +64,6 @@ Examples: num-cs = <1>; #address-cells = <1>; #size-cells = <0>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 1e8a8578148f..6dbdeb3c361a 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -9,7 +9,7 @@ Required SoC Specific Properties: - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - - samsung,exynos4210-spi: for exynos4 and exynos5 platforms + - samsung,exynos7-spi: for exynos7 platforms - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 042a0273b8ba..b7ba01ad1426 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -12,6 +12,9 @@ I. For patch submitters devicetree@vger.kernel.org + 3) The Documentation/ portion of the patch should come in the series before + the code implementing the binding. + II. For kernel maintainers 1) If you aren't comfortable reviewing a given binding, reply to it and ask diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt index 1f0f67234a91..3c67bd50aa10 100644 --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt @@ -1,7 +1,10 @@ * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs Required properties: -- compatible : "fsl,imx6q-thermal" +- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX. + i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC, + when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature + is higher than panic threshold, system will auto reboot by SRC module. - fsl,tempmon : phandle pointer to system controller that contains TEMPMON control registers, e.g. ANATOP on imx6q. - fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 0ef00be44b01..43404b197933 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -7,7 +7,10 @@ Required properties: - "renesas,thermal-r8a73a4" (R-Mobile AP6) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - - "renesas,thermal-r8a7791" (R-Car M2) + - "renesas,thermal-r8a7791" (R-Car M2-W) + - "renesas,thermal-r8a7792" (R-Car V2H) + - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". diff --git a/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt b/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt new file mode 100644 index 000000000000..a092053f7902 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt @@ -0,0 +1,15 @@ +Amlogic Meson6 SoCs Timer Controller + +Required properties: + +- compatible : should be "amlogic,meson6-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer + +Example: + +timer@c1109940 { + compatible = "amlogic,meson6-timer"; + reg = <0xc1109940 0x14>; + interrupts = <0 10 1>; +}; diff --git a/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt index f455182b1086..e9c78ce880e6 100644 --- a/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt +++ b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt @@ -2,8 +2,10 @@ Marvell Armada 370 and Armada XP Timers --------------------------------------- Required properties: -- compatible: Should be either "marvell,armada-370-timer" or - "marvell,armada-xp-timer" as appropriate. +- compatible: Should be one of the following + "marvell,armada-370-timer", + "marvell,armada-375-timer", + "marvell,armada-xp-timer". - interrupts: Should contain the list of Global Timer interrupts and then local timer interrupts - reg: Should contain location and length for timers register. First @@ -13,7 +15,8 @@ Required properties: Clocks required for compatible = "marvell,armada-370-timer": - clocks : Must contain a single entry describing the clock input -Clocks required for compatible = "marvell,armada-xp-timer": +Clocks required for compatibles = "marvell,armada-xp-timer", + "marvell,armada-375-timer": - clocks : Must contain an entry for each entry in clock-names. - clock-names : Must include the following entries: "nbclk" (L2/coherency fabric clock), diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index a17418b0ece3..1a05c1b243c1 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -11,15 +11,47 @@ datasheets. Required Properties: - - compatible: must contain one of the following. - - "renesas,cmt-32" for the 32-bit CMT + - compatible: must contain one or more of the following: + - "renesas,cmt-32-r8a7740" for the r8a7740 32-bit CMT + (CMT0) + - "renesas,cmt-32-sh7372" for the sh7372 32-bit CMT + (CMT0) + - "renesas,cmt-32-sh73a0" for the sh73a0 32-bit CMT + (CMT0) + - "renesas,cmt-32" for all 32-bit CMT without fast clock support (CMT0 on sh7372, sh73a0 and r8a7740) - - "renesas,cmt-32-fast" for the 32-bit CMT with fast clock support + This is a fallback for the above renesas,cmt-32-* entries. + + - "renesas,cmt-32-fast-r8a7740" for the r8a7740 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast-sh7372" for the sh7372 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast-sh73a0" for the sh73A0 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast" for all 32-bit CMT with fast clock support (CMT[234] on sh7372, sh73a0 and r8a7740) - - "renesas,cmt-48" for the 48-bit CMT + This is a fallback for the above renesas,cmt-32-fast-* entries. + + - "renesas,cmt-48-sh7372" for the sh7372 48-bit CMT + (CMT1) + - "renesas,cmt-48-sh73a0" for the sh73A0 48-bit CMT + (CMT1) + - "renesas,cmt-48-r8a7740" for the r8a7740 48-bit CMT + (CMT1) + - "renesas,cmt-48" for all non-second generation 48-bit CMT (CMT1 on sh7372, sh73a0 and r8a7740) - - "renesas,cmt-48-gen2" for the second generation 48-bit CMT + This is a fallback for the above renesas,cmt-48-* entries. + + - "renesas,cmt-48-r8a73a4" for the r8a73a4 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-r8a7790" for the r8a7790 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-r8a7791" for the r8a7791 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-gen2" for all second generation 48-bit CMT (CMT[01] on r8a73a4, r8a7790 and r8a7791) + This is a fallback for the renesas,cmt-48-r8a73a4, + renesas,cmt-48-r8a7790 and renesas,cmt-48-r8a7791 entries. - reg: base address and length of the registers block for the timer module. - interrupts: interrupt-specifier for the timer, one per channel. @@ -36,7 +68,7 @@ Example: R8A7790 (R-Car H2) CMT0 node them channels 0 and 1 in the documentation. cmt0: timer@ffca0000 { - compatible = "renesas,cmt-48-gen2"; + compatible = "renesas,cmt-48-r8a7790", "renesas,cmt-48-gen2"; reg = <0 0xffca0000 0 0x1004>; interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>, <0 142 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/timer/renesas,mtu2.txt b/Documentation/devicetree/bindings/timer/renesas,mtu2.txt index 917453f826bc..ba0a34d97eb8 100644 --- a/Documentation/devicetree/bindings/timer/renesas,mtu2.txt +++ b/Documentation/devicetree/bindings/timer/renesas,mtu2.txt @@ -1,4 +1,4 @@ -* Renesas R-Car Multi-Function Timer Pulse Unit 2 (MTU2) +* Renesas Multi-Function Timer Pulse Unit 2 (MTU2) The MTU2 is a multi-purpose, multi-channel timer/counter with configurable clock inputs and programmable compare match. @@ -8,7 +8,10 @@ are independent. The MTU2 hardware supports five channels indexed from 0 to 4. Required Properties: - - compatible: must contain "renesas,mtu2" + - compatible: must be one or more of the following: + - "renesas,mtu2-r7s72100" for the r7s72100 MTU2 + - "renesas,mtu2" for any MTU2 + This is a fallback for the above renesas,mtu2-* entries - reg: base address and length of the registers block for the timer module. @@ -26,7 +29,7 @@ Required Properties: Example: R7S72100 (RZ/A1H) MTU2 node mtu2: timer@fcff0000 { - compatible = "renesas,mtu2"; + compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; reg = <0xfcff0000 0x400>; interrupts = <0 139 IRQ_TYPE_LEVEL_HIGH>, <0 146 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/timer/renesas,tmu.txt b/Documentation/devicetree/bindings/timer/renesas,tmu.txt index 425d0c5f4aee..cd5f20bf2582 100644 --- a/Documentation/devicetree/bindings/timer/renesas,tmu.txt +++ b/Documentation/devicetree/bindings/timer/renesas,tmu.txt @@ -1,4 +1,4 @@ -* Renesas R-Car Timer Unit (TMU) +* Renesas R-Mobile/R-Car Timer Unit (TMU) The TMU is a 32-bit timer/counter with configurable clock inputs and programmable compare match. @@ -8,7 +8,12 @@ are independent. The TMU hardware supports up to three channels. Required Properties: - - compatible: must contain "renesas,tmu" + - compatible: must contain one or more of the following: + - "renesas,tmu-r8a7740" for the r8a7740 TMU + - "renesas,tmu-r8a7778" for the r8a7778 TMU + - "renesas,tmu-r8a7779" for the r8a7779 TMU + - "renesas,tmu" for any TMU. + This is a fallback for the above renesas,tmu-* entries - reg: base address and length of the registers block for the timer module. @@ -27,7 +32,7 @@ Optional Properties: Example: R8A7779 (R-Car H1) TMU0 node tmu0: timer@ffd80000 { - compatible = "renesas,tmu"; + compatible = "renesas,tmu-r8a7779", "renesas,tmu"; reg = <0xffd80000 0x30>; interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>, <0 33 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 20468b2a7516..53579197eca2 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -8,9 +8,50 @@ Required properties: - interrupts : <interrupt mapping for UFS host controller IRQ> - reg : <registers mapping> +Optional properties: +- vdd-hba-supply : phandle to UFS host controller supply regulator node +- vcc-supply : phandle to VCC supply regulator node +- vccq-supply : phandle to VCCQ supply regulator node +- vccq2-supply : phandle to VCCQ2 supply regulator node +- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V + or 2.7-3.6V. This boolean property when set, specifies + to use low voltage range of 1.7-1.95V. Note for external + UFS cards this property is invalid and valid VCC range is + always 2.7-3.6V. +- vcc-max-microamp : specifies max. load that can be drawn from vcc supply +- vccq-max-microamp : specifies max. load that can be drawn from vccq supply +- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply +- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator + +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. + +Note: If above properties are not defined it can be assumed that the supply +regulators or clocks are always on. + Example: ufshc@0xfc598000 { compatible = "jedec,ufs-1.1"; reg = <0xfc598000 0x800>; interrupts = <0 28 0>; + + vdd-hba-supply = <&xxx_reg0>; + vdd-hba-fixed-regulator; + vcc-supply = <&xxx_reg1>; + vcc-supply-1p8; + vccq-supply = <&xxx_reg2>; + vccq2-supply = <&xxx_reg3>; + vcc-max-microamp = 500000; + vccq-max-microamp = 200000; + vccq2-max-microamp = 200000; + + clocks = <&core 0>, <&ref 0>, <&iface 0>; + clock-names = "core_clk", "ref_clk", "iface_clk"; + freq-table-hz = <100000000 200000000>, <0 0>, <0 0>; }; diff --git a/Documentation/devicetree/bindings/unittest.txt b/Documentation/devicetree/bindings/unittest.txt new file mode 100644 index 000000000000..0f92a22fddfa --- /dev/null +++ b/Documentation/devicetree/bindings/unittest.txt @@ -0,0 +1,14 @@ +* OF selftest platform device + +** selftest + +Required properties: +- compatible: must be "selftest" + +All other properties are optional. + +Example: + selftest { + compatible = "selftest"; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt index 1bae71e9ad47..38a548001e3a 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt @@ -19,6 +19,7 @@ Optional properties: - disable-over-current: disable over current detect - external-vbus-divider: enables off-chip resistor divider for Vbus - maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts Examples: usb@02184000 { /* USB OTG */ @@ -30,4 +31,5 @@ usb@02184000 { /* USB OTG */ disable-over-current; external-vbus-divider; maximum-speed = "full-speed"; + tpl-support; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt new file mode 100644 index 000000000000..27f8b1e5ee46 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -0,0 +1,24 @@ +* USB2 ChipIdea USB controller for ci13xxx + +Required properties: +- compatible: should be "chipidea,usb2" +- reg: base address and length of the registers +- interrupts: interrupt for the USB controller + +Optional properties: +- clocks: reference to the USB clock +- phys: reference to the USB PHY +- phy-names: should be "usb-phy" +- vbus-supply: reference to the VBUS regulator + +Example: + + usb@f7ed0000 { + compatible = "chipidea,usb2"; + reg = <0xf7ed0000 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_USB0>; + phys = <&usb_phy0>; + phy-names = "usb-phy"; + vbus-supply = <®_usb0_vbus>; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 467ddd15d40c..482f815363ef 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -4,6 +4,9 @@ Platform DesignWare HS OTG USB 2.0 controller Required properties: - compatible : One of: - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. + - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; + - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; + - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt @@ -15,6 +18,8 @@ Optional properties: - phys: phy provider specifier - phy-names: shall be "usb2-phy" Refer to phy/phy-bindings.txt for generic phy consumer properties +- dr_mode: shall be one of "host", "peripheral" and "otg" + Refer to usb/generic.txt Example: diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt new file mode 100644 index 000000000000..f9d70252bbb2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -0,0 +1,68 @@ +ST DWC3 glue logic + +This file documents the parameters for the dwc3-st driver. +This driver controls the glue logic used to configure the dwc3 core on +STiH407 based platforms. + +Required properties: + - compatible : must be "st,stih407-dwc3" + - reg : glue logic base address and USB syscfg ctrl register offset + - reg-names : should be "reg-glue" and "syscfg-reg" + - st,syscon : should be phandle to system configuration node which + encompasses the glue registers + - resets : list of phandle and reset specifier pairs. There should be two entries, one + for the powerdown and softreset lines of the usb3 IP + - reset-names : list of reset signal names. Names should be "powerdown" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property + + - pinctl-names : A pinctrl state named "default" must be defined +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - pinctrl-0 : Pin control group +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + +Sub-nodes: +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the +example below. The DT binding details of dwc3 can be found in: +Documentation/devicetree/bindings/usb/dwc3.txt + +NB: The dr_mode property described in [1] is NOT optional for this driver, as the default value +is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host" +or "device". + +[1] Documentation/devicetree/bindings/usb/generic.txt + +Example: + +st_dwc3: dwc3@8f94000 { + status = "disabled"; + compatible = "st,stih407-dwc3"; + reg = <0x08f94000 0x1000>, <0x110 0x4>; + reg-names = "reg-glue", "syscfg-reg"; + st,syscfg = <&syscfg_core>; + resets = <&powerdown STIH407_USB3_POWERDOWN>, + <&softreset STIH407_MIPHY2_SOFTRESET>; + reset-names = "powerdown", + "softreset"; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; + ranges; + + dwc3: dwc3@9900000 { + compatible = "snps,dwc3"; + reg = <0x09900000 0x100000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + dr_mode = "host"; + phys-names = "usb2-phy", "usb3-phy"; + phys = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 471366d6a129..cd7f0454e13a 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -14,6 +14,29 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - snps,disable_scramble_quirk: true when SW should disable data scrambling. + Only really useful for FPGA builds. + - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled + - snps,lpm-nyet-threshold: LPM NYET threshold + - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk + - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk + - snps,req_p1p2p3_quirk: when set, the core will always request for + P1/P2/P3 transition sequence. + - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain + amount of 8B10B errors occur. + - snps,del_phy_power_chg_quirk: when set core will delay PHY power change + from P0 to P1/P2/P3. + - snps,lfps_filter_quirk: when set core will filter LFPS reception. + - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start + Polling LFPS after RX.Detect. + - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value. + - snps,tx_de_emphasis: the value driven to the PHY is controlled by the + LTSSM during USB3 Compliance mode. + - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. + - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal + utmi_l1_suspend_n, false when asserts utmi_sleep_n + - snps,hird-threshold: HIRD threshold This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt new file mode 100644 index 000000000000..fb45fa5770bb --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -0,0 +1,39 @@ +ST USB EHCI controller + +Required properties: + - compatible : must be "st,st-ehci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one EHCI interrupt should be described here + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : phandle referencing pin configuration of the USB controller +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + - resets : phandle + reset specifier pairs to the powerdown and softreset lines + of the USB IP + - reset-names : should be "power" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ehci1: usb@0xfe203e00 { + compatible = "st,st-ehci-300x"; + reg = <0xfe203e00 0x100>; + interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + clocks = <&clk_s_a1_ls 0>; + phys = <&usb2_phy>; + phy-names = "usb"; + status = "okay"; + + resets = <&powerdown STIH416_USB1_POWERDOWN>, + <&softreset STIH416_USB1_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index a3b5990d0f2c..9b4dbe3b2acc 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -82,8 +82,10 @@ Example: DWC3 Required properties: - - compatible: should be "samsung,exynos5250-dwusb3" for USB 3.0 DWC3 - controller. + - compatible: should be one of the following - + "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on + Exynos5250/5420. + "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. - #address-cells, #size-cells : should be '1' if the device has sub-nodes with 'reg' property. - ranges: allows valid 1:1 translation between child's address space and diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt index 96681c93b86d..379b84a567cc 100644 --- a/Documentation/devicetree/bindings/usb/mxs-phy.txt +++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt @@ -5,6 +5,7 @@ Required properties: * "fsl,imx23-usbphy" for imx23 and imx28 * "fsl,imx6q-usbphy" for imx6dq and imx6dl * "fsl,imx6sl-usbphy" for imx6sl + * "fsl,vf610-usbphy" for Vybrid vf610 * "fsl,imx6sx-usbphy" for imx6sx "fsl,imx23-usbphy" is still a fallback for other strings - reg: Should contain registers location and length diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt new file mode 100644 index 000000000000..6d8393748da2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-st.txt @@ -0,0 +1,37 @@ +ST USB OHCI controller + +Required properties: + + - compatible : must be "st,st-ohci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one OHCI controller interrupt should be described here + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + + - resets : phandle to the powerdown and reset controller for the USB IP + - reset-names : should be "power" and "softreset". +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ohci0: usb@0xfe1ffc00 { + compatible = "st,st-ohci-300x"; + reg = <0xfe1ffc00 0x100>; + interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>; + clocks = <&clk_s_a1_ls 0>, + <&clockgen_b0 0>; + clock-names = "ic", "clk48"; + phys = <&usb2_phy>; + phy-names = "usb"; + status = "okay"; + + resets = <&powerdown STIH416_USB0_POWERDOWN>, + <&softreset STIH416_USB0_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt index 79729a948d5a..9c331799b87c 100644 --- a/Documentation/devicetree/bindings/usb/pxa-usb.txt +++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt @@ -29,3 +29,25 @@ Example: marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ }; +UDC + +Required properties: + - compatible: Should be "marvell,pxa270-udc" for USB controllers + used in device mode. + - reg: usb device MMIO address space + - interrupts: single interrupt generated by the UDC IP + - clocks: input clock of the UDC IP (see clock-bindings.txt) + +Optional properties: + - gpios: + - gpio activated to control the USB D+ pullup (see gpio.txt) + +Example: + + pxa27x_udc: udc@40600000 { + compatible = "marvell,pxa270-udc"; + reg = <0x40600000 0x10000>; + interrupts = <11>; + clocks = <&pxa2xx_clks 11>; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt new file mode 100644 index 000000000000..ca164e71dd50 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -0,0 +1,66 @@ +Qualcomm SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "qcom,dwc3" +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "core" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + +Optional clocks: + "iface" System bus AXI clock. Not present on all platforms + "sleep" Sleep clock, used when USB3 core goes into low + power mode (U3). + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt + +Example device nodes: + + hs_phy: phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + ss_phy: phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + usb3_0: usb30@0 { + compatible = "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + status = "ok"; + + dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <0 205 0x4>; + phys = <&hs_phy>, <&ss_phy>; + phy-names = "usb2-phy", "usb3-phy"; + tx-fifo-resize; + dr_mode = "host"; + }; + }; + diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt new file mode 100644 index 000000000000..b08c903f8668 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -0,0 +1,24 @@ +Renesas Electronics USBHS driver + +Required properties: + - compatible: Must contain one of the following: + - "renesas,usbhs-r8a7790" + - "renesas,usbhs-r8a7791" + - reg: Base address and length of the register for the USBHS + - interrupts: Interrupt specifier for the USBHS + - clocks: A list of phandle + clock specifier pairs + +Optional properties: + - renesas,buswait: Integer to use BUSWAIT register + - renesas,enable-gpio: A gpio specifier to check GPIO determining if USB + function should be enabled + - phys: phandle + phy specifier pair + - phy-names: must be "usb" + +Example: + usbhs: usb@e6590000 { + compatible = "renesas,usbhs-r8a7790"; + reg = <0 0xe6590000 0 0x100>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + }; diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt b/Documentation/devicetree/bindings/usb/udc-xilinx.txt new file mode 100644 index 000000000000..47b4e397a08d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt @@ -0,0 +1,18 @@ +Xilinx USB2 device controller + +Required properties: +- compatible : Should be "xlnx,usb2-device-4.00.a" +- reg : Physical base address and size of the USB2 + device registers map. +- interrupts : Should contain single irq line of USB2 device + controller +- xlnx,has-builtin-dma : if DMA is included + +Example: + axi-usb2-device@42e00000 { + compatible = "xlnx,usb2-device-4.00.a"; + interrupts = <0x0 0x39 0x1>; + reg = <0x42e00000 0x10000>; + xlnx,has-builtin-dma; + }; + diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index b968a1aea995..19233b7365e1 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -9,6 +9,8 @@ Optional properties: - big-endian-regs : boolean, set this for hcds with big-endian registers - big-endian-desc : boolean, set this for hcds with big-endian descriptors - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc +- no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA +- num-ports : u32, to override the detected port count - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 221ac0dbc678..52493b1480e2 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -8,8 +8,8 @@ Optional properties: if I2C is used. - connect-gpios: Should specify GPIO for connect. - disabled-ports: Should specify the ports unused. - '1' or '2' or '3' are availe for this property to describe the port - number. 1~3 property values are possible to be desribed. + '1' or '2' or '3' are available for this property to describe the port + number. 1~3 property values are possible to be described. Do not describe this property if all ports have to be enabled. - intn-gpios: Should specify GPIO for interrupt. - reset-gpios: Should specify GPIO for reset. diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt index 97ce94e1a6cc..c101a4b17131 100644 --- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -4,6 +4,7 @@ Required properties: - #index-cells: Cells used to descibe usb controller index. Should be <1> - compatible: Should be one of below: "fsl,imx6q-usbmisc" for imx6q + "fsl,vf610-usbmisc" for Vybrid vf610 - reg: Should contain registers location and length Examples: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index e6469ec7a90e..b1df0ad1306c 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -14,6 +14,7 @@ allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. +amlogic Amlogic, Inc. ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) @@ -29,36 +30,47 @@ calxeda Calxeda capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. +chipidea Chipidea, Inc chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. +cnm Chips&Media, Inc. cortina Cortina Systems, Inc. crystalfontz Crystalfontz America, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. denx Denx Software Engineering digi Digi International Inc. +digilent Diglent, Inc. +dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG ebv EBV Elektronik edt Emerging Display Technologies elan Elan Microelectronic Corp. emmicro EM Microelectronic +energymicro Silicon Laboratories (formerly Energy Micro AS) epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. est ESTeem Wireless Modems eukrea Eukréa Electromatique +everest Everest Semiconductor Co. Ltd. excito Excito +fcs Fairchild Semiconductor fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +geniatech Geniatech, Inc. globalscale Globalscale Technologies, Inc. gmt Global Mixed-mode Technology, Inc. google Google, Inc. gumstix Gumstix, Inc. +gw Gateworks Corporation +hannstar HannStar Display Corporation haoyu Haoyu Microelectronic Co. Ltd. hisilicon Hisilicon Limited. +hit Hitachi Ltd. honeywell Honeywell hp Hewlett Packard i2se I2SE GmbH @@ -66,9 +78,11 @@ ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. iom Iomega Corporation img Imagination Technologies Ltd. +innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group isee ISEE 2007 S.L. +isil Intersil (deprecated, use isl) isl Intersil karo Ka-Ro electronics GmbH keymile Keymile GmbH @@ -82,11 +96,15 @@ lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products mediatek MediaTek Inc. +merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. +micron Micron Technology Inc. +mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. @@ -101,6 +119,7 @@ nxp NXP Semiconductors onnn ON Semiconductor Corp. opencores OpenCores.org panasonic Panasonic Corporation +pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. @@ -118,6 +137,7 @@ renesas Renesas Electronics Corporation ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC @@ -125,21 +145,26 @@ sil Silicon Image silabs Silicon Laboratories simtek sii Seiko Instruments, Inc. +silergy Silergy Corp. sirf SiRF Technology, Inc. +sitronix Sitronix Technology Corporation smsc Standard Microsystems Corporation -snps Synopsys, Inc. +snps Synopsys, Inc. solidrun SolidRun +sony Sony Corporation spansion Spansion Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson synology Synology, Inc. +tbs TBS Technologies +thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz -usi Universal Scientifc Industrial Co., Ltd. +usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. via VIA Technologies, Inc. @@ -148,6 +173,7 @@ winbond Winbond Electronics corp. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. xes Extreme Engineering Solutions (X-ES) +xillybus Xillybus Ltd. xlnx Xilinx zyxel ZyXEL Communications Corp. zarlink Zarlink Semiconductor diff --git a/Documentation/devicetree/bindings/video/adi,adv7123.txt b/Documentation/devicetree/bindings/video/adi,adv7123.txt new file mode 100644 index 000000000000..a6b2b2b8f3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/video/adi,adv7123.txt @@ -0,0 +1,50 @@ +Analog Device ADV7123 Video DAC +------------------------------- + +The ADV7123 is a digital-to-analog converter that outputs VGA signals from a +parallel video input. + +Required properties: + +- compatible: Should be "adi,adv7123" + +Optional properties: + +- psave-gpios: Power save control GPIO + +Required nodes: + +The ADV7123 has two video ports. Their connections are modeled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DPI input +- Video port 1 for VGA output + + +Example +------- + + adv7123: encoder@0 { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7123_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7123_out: endpoint@0 { + remote-endpoint = <&vga_connector_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/adi,adv7511.txt b/Documentation/devicetree/bindings/video/adi,adv7511.txt new file mode 100644 index 000000000000..96c25ee01501 --- /dev/null +++ b/Documentation/devicetree/bindings/video/adi,adv7511.txt @@ -0,0 +1,88 @@ +Analog Device ADV7511(W)/13 HDMI Encoders +----------------------------------------- + +The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, +S/PDIF, CEC and HDCP. + +Required properties: + +- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- reg: I2C slave address + +The ADV7511 supports a large number of input data formats that differ by their +color depth, color format, clock mode, bit justification and random +arrangement of components on the data bus. The combination of the following +properties describe the input and map directly to the video input tables of the +ADV7511 datasheet that document all the supported combinations. + +- adi,input-depth: Number of bits per color component at the input (8, 10 or + 12). +- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or + "yuv444". +- adi,input-clock: The input clock type, one of "1x" (one clock cycle per + pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel, + data driven on both edges). + +The following input format properties are required except in "rgb 1x" and +"yuv444 1x" modes, in which case they must not be specified. + +- adi,input-style: The input components arrangement variant (1, 2 or 3), as + listed in the input format tables in the datasheet. +- adi,input-justification: The input bit justification ("left", "evenly", + "right"). + +Optional properties: + +- interrupts: Specifier for the ADV7511 interrupt +- pd-gpios: Specifier for the GPIO connected to the power down signal + +- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps + (-1200 ps .. 1600 ps). Defaults to no delay. +- adi,embedded-sync: The input uses synchronization signals embedded in the + data stream (similar to BT.656). Defaults to separate H/V synchronization + signals. + +Required nodes: + +The ADV7511 has two video ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for the RGB or YUV input +- Video port 1 for the HDMI output + + +Example +------- + + adv7511w: hdmi@39 { + compatible = "adi,adv7511w"; + reg = <39>; + interrupt-parent = <&gpio3>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511w_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt index b75af94a5e52..f059dd0b3d28 100644 --- a/Documentation/devicetree/bindings/video/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt @@ -20,6 +20,9 @@ Required nodes: - default-mode: a videomode within the display with timing parameters as specified below. +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + Example: fb0: fb@0x00500000 { @@ -39,8 +42,8 @@ Atmel LCDC Display ----------------------------------------------------- Required properties (as per of_videomode_helper): - - atmel,dmacon: dma controler configuration - - atmel,lcdcon2: lcd controler configuration + - atmel,dmacon: dma controller configuration + - atmel,lcdcon2: lcd controller configuration - atmel,guard-time: lcd guard time (Delay in frame periods) - bits-per-pixel: lcd panel bit-depth. diff --git a/Documentation/devicetree/bindings/video/backlight/lp855x.txt b/Documentation/devicetree/bindings/video/backlight/lp855x.txt index 96e83a56048e..0a3ecbc3a1b9 100644 --- a/Documentation/devicetree/bindings/video/backlight/lp855x.txt +++ b/Documentation/devicetree/bindings/video/backlight/lp855x.txt @@ -12,6 +12,7 @@ Optional properties: - pwm-period: PWM period value. Set only PWM input mode used (u32) - rom-addr: Register address of ROM area to be updated (u8) - rom-val: Register value to be updated (u8) + - power-supply: Regulator which controls the 3V rail Example: @@ -56,6 +57,7 @@ Example: backlight@2c { compatible = "ti,lp8557"; reg = <0x2c>; + power-supply = <&backlight_vdd>; dev-ctrl = /bits/ 8 <0x41>; init-brt = /bits/ 8 <0x0a>; diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt index 31036c667d54..ca2b4aacd9af 100644 --- a/Documentation/devicetree/bindings/video/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt @@ -2,7 +2,9 @@ Exynos MIPI DSI Master Required properties: - compatible: value should be one of the following + "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ + "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ - reg: physical base address and length of the registers set for the device - interrupts: should contain DSI interrupt diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt index 0329f60d431e..8c8c2f4e4c3f 100644 --- a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt +++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt @@ -20,7 +20,7 @@ Optional properties: register is not modified as recommended by the datasheet. - fsl,lpccr: Contrast Control Register value. This property provides the default value for the contrast control register. - If that property is ommited, the register is zeroed. + If that property is omitted, the register is zeroed. - fsl,lscr1: LCDC Sharp Configuration Register value. Example: diff --git a/Documentation/devicetree/bindings/video/renesas,du.txt b/Documentation/devicetree/bindings/video/renesas,du.txt new file mode 100644 index 000000000000..5102830f2760 --- /dev/null +++ b/Documentation/devicetree/bindings/video/renesas,du.txt @@ -0,0 +1,84 @@ +* Renesas R-Car Display Unit (DU) + +Required Properties: + + - compatible: must be one of the following. + - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU + - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU + - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU + + - reg: A list of base address and length of each memory resource, one for + each entry in the reg-names property. + - reg-names: Name of the memory resources. The DU requires one memory + resource for the DU core (named "du") and one memory resource for each + LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical + index). + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifiers for the DU interrupts. + + - clocks: A list of phandles + clock-specifier pairs, one for each entry in + the clock-names property. + - clock-names: Name of the clocks. This property is model-dependent. + - R8A7779 uses a single functional clock. The clock doesn't need to be + named. + - R8A7790 and R8A7791 use one functional clock per channel and one clock + per LVDS encoder. The functional clocks must be named "du.x" with "x" + being the channel numerical index. The LVDS clocks must be named + "lvds.x" with "x" being the LVDS encoder numerical index. + +Required nodes: + +The connections to the DU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each DU output. + + Port 0 Port1 Port2 +----------------------------------------------------------------------------- + R8A7779 (H1) DPAD 0 DPAD 1 - + R8A7790 (H2) DPAD LVDS 0 LVDS 1 + R8A7791 (M2) DPAD LVDS 0 - + + +Example: R8A7790 (R-Car H2) DU + + du: du@feb00000 { + compatible = "renesas,du-r8a7790"; + reg = <0 0xfeb00000 0 0x70000>, + <0 0xfeb90000 0 0x1c>, + <0 0xfeb94000 0 0x1c>; + reg-names = "du", "lvds.0", "lvds.1"; + interrupt-parent = <&gic>; + interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, + <0 268 IRQ_TYPE_LEVEL_HIGH>, + <0 269 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_DU0>, + <&mstp7_clks R8A7790_CLK_DU1>, + <&mstp7_clks R8A7790_CLK_DU2>, + <&mstp7_clks R8A7790_CLK_LVDS0>, + <&mstp7_clks R8A7790_CLK_LVDS1>; + clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + port@1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + port@2 { + reg = <2>; + du_out_lvds1: endpoint { + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/rockchip-drm.txt b/Documentation/devicetree/bindings/video/rockchip-drm.txt new file mode 100644 index 000000000000..7fff582495a2 --- /dev/null +++ b/Documentation/devicetree/bindings/video/rockchip-drm.txt @@ -0,0 +1,19 @@ +Rockchip DRM master device +================================ + +The Rockchip DRM master device is a virtual device needed to list all +vop devices or other display interface nodes that comprise the +graphics subsystem. + +Required properties: +- compatible: Should be "rockchip,display-subsystem" +- ports: Should contain a list of phandles pointing to display interface port + of vop devices. vop definitions as defined in + Documentation/devicetree/bindings/video/rockchip-vop.txt + +example: + +display-subsystem { + compatible = "rockchip,display-subsystem"; + ports = <&vopl_out>, <&vopb_out>; +}; diff --git a/Documentation/devicetree/bindings/video/rockchip-vop.txt b/Documentation/devicetree/bindings/video/rockchip-vop.txt new file mode 100644 index 000000000000..d15351f2313d --- /dev/null +++ b/Documentation/devicetree/bindings/video/rockchip-vop.txt @@ -0,0 +1,58 @@ +device-tree bindings for rockchip soc display controller (vop) + +VOP (Visual Output Processor) is the Display Controller for the Rockchip +series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be one of the following + "rockchip,rk3288-vop"; + +- interrupts: should contain a list of all VOP IP block interrupts in the + order: VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: Must contain + aclk_vop: for ddr buffer transfer. + hclk_vop: for ahb bus to R/W the phy regs. + dclk_vop: pixel clock. + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - axi + - ahb + - dclk + +- iommus: required a iommu node + +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: +SoC specific DT entry: + vopb: vopb@ff930000 { + compatible = "rockchip,rk3288-vop"; + reg = <0xff930000 0x19c>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>; + clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; + reset-names = "axi", "ahb", "dclk"; + iommus = <&vopb_mmu>; + vopb_out: port { + #address-cells = <1>; + #size-cells = <0>; + vopb_out_edp: endpoint@0 { + reg = <0>; + remote-endpoint=<&edp_in_vopb>; + }; + vopb_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint=<&hdmi_in_vopb>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt index ecc899b9817b..cf1af6371021 100644 --- a/Documentation/devicetree/bindings/video/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt @@ -9,7 +9,9 @@ Required properties: "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ + "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ + "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ - reg: physical base address and length of the FIMD registers set. diff --git a/Documentation/devicetree/bindings/video/simple-framebuffer-sunxi.txt b/Documentation/devicetree/bindings/video/simple-framebuffer-sunxi.txt new file mode 100644 index 000000000000..c46ba641a1df --- /dev/null +++ b/Documentation/devicetree/bindings/video/simple-framebuffer-sunxi.txt @@ -0,0 +1,33 @@ +Sunxi specific Simple Framebuffer bindings + +This binding documents sunxi specific extensions to the simple-framebuffer +bindings. The sunxi simplefb u-boot code relies on the devicetree containing +pre-populated simplefb nodes. + +These extensions are intended so that u-boot can select the right node based +on which pipeline is being used. As such they are solely intended for +firmware / bootloader use, and the OS should ignore them. + +Required properties: +- compatible: "allwinner,simple-framebuffer" +- allwinner,pipeline, one of: + "de_be0-lcd0" + "de_be1-lcd1" + "de_be0-lcd0-hdmi" + "de_be1-lcd1-hdmi" + +Example: + +chosen { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + framebuffer@0 { + compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; + allwinner,pipeline = "de_be0-lcd0-hdmi"; + clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, + <&ahb_gates 44>; + status = "disabled"; + }; +}; diff --git a/Documentation/devicetree/bindings/video/simple-framebuffer.txt b/Documentation/devicetree/bindings/video/simple-framebuffer.txt index 70c26f3a5b9a..4474ef6e0b95 100644 --- a/Documentation/devicetree/bindings/video/simple-framebuffer.txt +++ b/Documentation/devicetree/bindings/video/simple-framebuffer.txt @@ -1,8 +1,40 @@ Simple Framebuffer -A simple frame-buffer describes a raw memory region that may be rendered to, -with the assumption that the display hardware has already been set up to scan -out from that buffer. +A simple frame-buffer describes a frame-buffer setup by firmware or +the bootloader, with the assumption that the display hardware has already +been set up to scan out from the memory pointed to by the reg property. + +Since simplefb nodes represent runtime information they must be sub-nodes of +the chosen node (*). Simplefb nodes must be named "framebuffer@<address>". + +If the devicetree contains nodes for the display hardware used by a simplefb, +then the simplefb node must contain a property called "display", which +contains a phandle pointing to the primary display hw node, so that the OS +knows which simplefb to disable when handing over control to a driver for the +real hardware. The bindings for the hw nodes must specify which node is +considered the primary node. + +It is advised to add display# aliases to help the OS determine how to number +things. If display# aliases are used, then if the simplefb node contains a +"display" property then the /aliases/display# path must point to the display +hw node the "display" property points to, otherwise it must point directly +to the simplefb node. + +If a simplefb node represents the preferred console for user interaction, +then the chosen node's stdout-path property should point to it, or to the +primary display hw node, as with display# aliases. If display aliases are +used then it should be set to the alias instead. + +It is advised that devicetree files contain pre-filled, disabled framebuffer +nodes, so that the firmware only needs to update the mode information and +enable them. This way if e.g. later on support for more display clocks get +added, the simplefb nodes will already contain this info and the firmware +does not need to be updated. + +If pre-filled framebuffer nodes are used, the firmware may need extra +information to find the right node. In that case an extra platform specific +compatible and platform specific properties should be used and documented, +see e.g. simple-framebuffer-sunxi.txt . Required properties: - compatible: "simple-framebuffer" @@ -14,13 +46,41 @@ Required properties: - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r). +Optional properties: +- clocks : List of clocks used by the framebuffer. Clocks listed here + are expected to already be configured correctly. The OS must + ensure these clocks are not modified or disabled while the + simple framebuffer remains active. +- display : phandle pointing to the primary display hardware node + Example: - framebuffer { +aliases { + display0 = &lcdc0; +} + +chosen { + framebuffer0: framebuffer@1d385000 { compatible = "simple-framebuffer"; reg = <0x1d385000 (1600 * 1200 * 2)>; width = <1600>; height = <1200>; stride = <(1600 * 2)>; format = "r5g6b5"; + clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>; + display = <&lcdc0>; + }; + stdout-path = "display0"; +}; + +soc@01c00000 { + lcdc0: lcdc@1c0c000 { + compatible = "allwinner,sun4i-a10-lcdc"; + ... }; +}; + + +*) Older devicetree files may have a compatible = "simple-framebuffer" node +in a different place, operating systems must first enumerate any compatible +nodes found under chosen and then check for other compatible nodes. diff --git a/Documentation/devicetree/bindings/video/thine,thc63lvdm83d b/Documentation/devicetree/bindings/video/thine,thc63lvdm83d new file mode 100644 index 000000000000..527e236e9a2a --- /dev/null +++ b/Documentation/devicetree/bindings/video/thine,thc63lvdm83d @@ -0,0 +1,50 @@ +THine Electronics THC63LVDM83D LVDS serializer +---------------------------------------------- + +The THC63LVDM83D is an LVDS serializer designed to support pixel data +transmission between a host and a flat panel. + +Required properties: + +- compatible: Should be "thine,thc63lvdm83d" + +Optional properties: + +- pwdn-gpios: Power down control GPIO + +Required nodes: + +The THC63LVDM83D has two video ports. Their connections are modeled using the +OFgraph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for CMOS/TTL input +- Video port 1 for LVDS output + + +Example +------- + + lvds_enc: encoder@0 { + compatible = "thine,thc63lvdm83d"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_enc_in: endpoint@0 { + remote-endpoint = <&rgb_out>; + }; + }; + + port@1 { + reg = <1>; + + lvds_enc_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/vga-connector.txt b/Documentation/devicetree/bindings/video/vga-connector.txt new file mode 100644 index 000000000000..c727f298e7ad --- /dev/null +++ b/Documentation/devicetree/bindings/video/vga-connector.txt @@ -0,0 +1,36 @@ +VGA Connector +============= + +Required properties: + +- compatible: "vga-connector" + +Optional properties: + +- label: a symbolic name for the connector corresponding to a hardware label +- ddc-i2c-bus: phandle to the I2C bus that is connected to VGA DDC + +Required nodes: + +The VGA connector internal connections are modeled using the OF graph bindings +specified in Documentation/devicetree/bindings/graph.txt. + +The VGA connector has a single port that must be connected to a video source +port. + + +Example +------- + +vga0: connector@0 { + compatible = "vga-connector"; + label = "vga"; + + ddc-i2c-bus = <&i2c3>; + + port { + vga_connector_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt new file mode 100644 index 000000000000..fef794741bd1 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt @@ -0,0 +1,17 @@ +* OMAP HDQ One wire bus master controller + +Required properties: +- compatible : should be "ti,omap3-1w" +- reg : Address and length of the register set for the device +- interrupts : interrupt line. +- ti,hwmods : "hdq1w" + +Example: + +- From omap3.dtsi + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; diff --git a/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt new file mode 100644 index 000000000000..c3a36ee45552 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt @@ -0,0 +1,24 @@ +Zynq Watchdog Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,wdt-r1p2". +- clocks : This is pclk (APB clock). +- interrupts : This is wd_irq - watchdog timeout interrupt. +- interrupt-parent : Must be core interrupt controller. + +Optional properties +- reset-on-timeout : If this property exists, then a reset is done + when watchdog times out. +- timeout-sec : Watchdog timeout value (in seconds). + +Example: + watchdog@f8005000 { + compatible = "cdns,wdt-r1p2"; + clocks = <&clkc 45>; + interrupt-parent = <&intc>; + interrupts = <0 9 1>; + reg = <0xf8005000 0x1000>; + reset-on-timeout; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index e52ba2da868c..8dab6fd024aa 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -7,7 +7,8 @@ Required properties: Optional property: - big-endian: If present the watchdog device's registers are implemented - in big endian mode, otherwise in little mode. + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. Examples: diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt index 97223fddb7bd..858ed9221ac4 100644 --- a/Documentation/devicetree/bindings/watchdog/marvel.txt +++ b/Documentation/devicetree/bindings/watchdog/marvel.txt @@ -17,6 +17,18 @@ For "marvell,armada-375-wdt" and "marvell,armada-380-wdt": - reg : A third entry is mandatory and should contain the shared mask/unmask RSTOUT address. +Clocks required for compatibles = "marvell,orion-wdt", + "marvell,armada-370-wdt": +- clocks : Must contain a single entry describing the clock input + +Clocks required for compatibles = "marvell,armada-xp-wdt" + "marvell,armada-375-wdt" + "marvell,armada-380-wdt": +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "nbclk" (L2/coherency fabric clock), + "fixed" (Reference 25 MHz fixed-clock). + Optional properties: - interrupts : Contains the IRQ for watchdog expiration @@ -30,4 +42,5 @@ Example: interrupts = <3>; timeout-sec = <10>; status = "okay"; + clocks = <&gate_clk 7>; }; diff --git a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt new file mode 100644 index 000000000000..9200fc2d508c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt @@ -0,0 +1,13 @@ +Meson SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson6-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@c1109900 { + compatible = "amlogic,meson6-wdt"; + reg = <0xc1109900 0x8>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt new file mode 100644 index 000000000000..4726924d034e --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt @@ -0,0 +1,24 @@ +Qualcomm Krait Processor Sub-system (KPSS) Watchdog +--------------------------------------------------- + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,kpss-wdt-msm8960" + "qcom,kpss-wdt-apq8064" + "qcom,kpss-wdt-ipq8064" + +- reg : shall contain base register location and length +- clocks : shall contain the input clock + +Optional properties : +- timeout-sec : shall contain the default watchdog timeout in seconds, + if unset, the default timeout is 30 seconds + +Example: + watchdog@208a038 { + compatible = "qcom,kpss-wdt-ipq8064"; + reg = <0x0208a038 0x40>; + clocks = <&sleep_clk>; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index cfff37511aac..8f3d96af81d7 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -9,6 +9,7 @@ Required properties: (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs (b) "samsung,exynos5250-wdt" for Exynos5250 (c) "samsung,exynos5420-wdt" for Exynos5420 + (c) "samsung,exynos7-wdt" for Exynos7 - reg : base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/staging/xillybus.txt b/Documentation/devicetree/bindings/xillybus/xillybus.txt index 9e316dc2e40f..9e316dc2e40f 100644 --- a/Documentation/devicetree/bindings/staging/xillybus.txt +++ b/Documentation/devicetree/bindings/xillybus/xillybus.txt diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 1f013bd0d320..77685185cf3b 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -51,6 +51,8 @@ Table of Contents VIII - Specifying device power management information (sleep property) + IX - Specifying dma bus information + Appendix A - Sample SOC node for MPC8540 @@ -1332,6 +1334,57 @@ reasonably grouped in this manner, then create a virtual sleep controller (similar to an interrupt nexus, except that defining a standardized sleep-map should wait until its necessity is demonstrated). +IX - Specifying dma bus information + +Some devices may have DMA memory range shifted relatively to the beginning of +RAM, or even placed outside of kernel RAM. For example, the Keystone 2 SoC +worked in LPAE mode with 4G memory has: +- RAM range: [0x8 0000 0000, 0x8 FFFF FFFF] +- DMA range: [ 0x8000 0000, 0xFFFF FFFF] +and DMA range is aliased into first 2G of RAM in HW. + +In such cases, DMA addresses translation should be performed between CPU phys +and DMA addresses. The "dma-ranges" property is intended to be used +for describing the configuration of such system in DT. + +In addition, each DMA master device on the DMA bus may or may not support +coherent DMA operations. The "dma-coherent" property is intended to be used +for identifying devices supported coherent DMA operations in DT. + +* DMA Bus master +Optional property: +- dma-ranges: <prop-encoded-array> encoded as arbitrary number of triplets of + (child-bus-address, parent-bus-address, length). Each triplet specified + describes a contiguous DMA address range. + The dma-ranges property is used to describe the direct memory access (DMA) + structure of a memory-mapped bus whose device tree parent can be accessed + from DMA operations originating from the bus. It provides a means of + defining a mapping or translation between the physical address space of + the bus and the physical address space of the parent of the bus. + (for more information see ePAPR specification) + +* DMA Bus child +Optional property: +- dma-ranges: <empty> value. if present - It means that DMA addresses + translation has to be enabled for this device. +- dma-coherent: Present if dma operations are coherent + +Example: +soc { + compatible = "ti,keystone","simple-bus"; + ranges = <0x0 0x0 0x0 0xc0000000>; + dma-ranges = <0x80000000 0x8 0x00000000 0x80000000>; + + [...] + + usb: usb@2680000 { + compatible = "ti,keystone-dwc3"; + + [...] + dma-coherent; + }; +}; + Appendix A - Sample SOC node for MPC8540 ======================================== diff --git a/Documentation/devicetree/dynamic-resolution-notes.txt b/Documentation/devicetree/dynamic-resolution-notes.txt new file mode 100644 index 000000000000..083d23262abe --- /dev/null +++ b/Documentation/devicetree/dynamic-resolution-notes.txt @@ -0,0 +1,25 @@ +Device Tree Dynamic Resolver Notes +---------------------------------- + +This document describes the implementation of the in-kernel +Device Tree resolver, residing in drivers/of/resolver.c and is a +companion document to Documentation/devicetree/dt-object-internal.txt[1] + +How the resolver works +---------------------- + +The resolver is given as an input an arbitrary tree compiled with the +proper dtc option and having a /plugin/ tag. This generates the +appropriate __fixups__ & __local_fixups__ nodes as described in [1]. + +In sequence the resolver works by the following steps: + +1. Get the maximum device tree phandle value from the live tree + 1. +2. Adjust all the local phandles of the tree to resolve by that amount. +3. Using the __local__fixups__ node information adjust all local references + by the same amount. +4. For each property in the __fixups__ node locate the node it references + in the live tree. This is the label used to tag the node. +5. Retrieve the phandle of the target of the fixup. +6. For each fixup in the property locate the node:property:offset location + and replace it with the phandle value. diff --git a/Documentation/devicetree/of_selftest.txt b/Documentation/devicetree/of_selftest.txt index 3a2f54d07fc5..57a808b588bf 100644 --- a/Documentation/devicetree/of_selftest.txt +++ b/Documentation/devicetree/of_selftest.txt @@ -63,18 +63,17 @@ struct device_node { struct device_node *parent; struct device_node *child; struct device_node *sibling; - struct device_node *allnext; /* next in list of all nodes */ ... }; -Figure 1, describes a generic structure of machine’s un-flattened device tree +Figure 1, describes a generic structure of machine's un-flattened device tree considering only child and sibling pointers. There exists another pointer, *parent, that is used to traverse the tree in the reverse direction. So, at a particular level the child node and all the sibling nodes will have a parent -pointer pointing to a common node (e.g. child1, sibling2, sibling3, sibling4’s +pointer pointing to a common node (e.g. child1, sibling2, sibling3, sibling4's parent points to root node) -root (‘/’) +root ('/') | child1 -> sibling2 -> sibling3 -> sibling4 -> null | | | | @@ -99,12 +98,6 @@ child11 -> sibling12 -> sibling13 -> sibling14 -> null Figure 1: Generic structure of un-flattened device tree -*allnext: it is used to link all the nodes of DT into a list. So, for the - above tree the list would be as follows: - -root->child1->child11->sibling12->sibling13->child131->sibling14->sibling2-> -child21->sibling22->sibling23->sibling3->child31->sibling32->sibling4->null - Before executing OF selftest, it is required to attach the test data to machine's device tree (if present). So, when selftest_data_add() is called, at first it reads the flattened device tree data linked into the kernel image @@ -113,8 +106,8 @@ via the following kernel symbols: __dtb_testcases_begin - address marking the start of test data blob __dtb_testcases_end - address marking the end of test data blob -Secondly, it calls of_fdt_unflatten_device_tree() to unflatten the flattened -blob. And finally, if the machine’s device tree (i.e live tree) is present, +Secondly, it calls of_fdt_unflatten_tree() to unflatten the flattened +blob. And finally, if the machine's device tree (i.e live tree) is present, then it attaches the unflattened test data tree to the live tree, else it attaches itself as a live device tree. @@ -122,7 +115,7 @@ attach_node_and_children() uses of_attach_node() to attach the nodes into the live tree as explained below. To explain the same, the test data tree described in Figure 2 is attached to the live tree described in Figure 1. -root (‘/’) +root ('/') | testcase-data | @@ -131,15 +124,10 @@ root (‘/’) test-child01 null null null -allnext list: - -root->testcase-data->test-child0->test-child01->test-sibling1->test-sibling2 -->test-sibling3->null - Figure 2: Example test data tree to be attached to live tree. -According to the scenario above, the live tree is already present so it isn’t -required to attach the root(‘/’) node. All other nodes are attached by calling +According to the scenario above, the live tree is already present so it isn't +required to attach the root('/') node. All other nodes are attached by calling of_attach_node() on each node. In the function of_attach_node(), the new node is attached as the child of the @@ -148,7 +136,7 @@ replaces the current child and turns it into its sibling. So, when the testcase data node is attached to the live tree above (Figure 1), the final structure is as shown in Figure 3. -root (‘/’) +root ('/') | testcase-data -> child1 -> sibling2 -> sibling3 -> sibling4 -> null | | | | | @@ -170,7 +158,7 @@ testcase-data -> child1 -> sibling2 -> sibling3 -> sibling4 -> null null ----------------------------------------------------------------------- -root (‘/’) +root ('/') | testcase-data -> child1 -> sibling2 -> sibling3 -> sibling4 -> null | | | | | @@ -191,8 +179,8 @@ test-child0 the test-sibling1 is attached that pushes the child node as mentioned above. If a duplicate node is found (i.e. if a node with same full_name property is -already present in the live tree), then the node isn’t attached rather its -properties are updated to the live tree’s node by calling the function +already present in the live tree), then the node isn't attached rather its +properties are updated to the live tree's node by calling the function update_node_properties(). @@ -204,8 +192,6 @@ detached and then moving up the parent nodes are removed, and eventually the whole tree). selftest_data_remove() calls detach_node_and_children() that uses of_detach_node() to detach the nodes from the live device tree. -To detach a node, of_detach_node() first updates all_next linked list, by -attaching the previous node’s allnext to current node’s allnext pointer. And -then, it either updates the child pointer of given node’s parent to its -sibling or attaches the previous sibling to the given node’s sibling, as -appropriate. That is it :) +To detach a node, of_detach_node() either updates the child pointer of given +node's parent to its sibling or attaches the previous sibling to the given +node's sibling, as appropriate. That is it :) diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt new file mode 100644 index 000000000000..30ae758e3eef --- /dev/null +++ b/Documentation/devicetree/overlay-notes.txt @@ -0,0 +1,133 @@ +Device Tree Overlay Notes +------------------------- + +This document describes the implementation of the in-kernel +device tree overlay functionality residing in drivers/of/overlay.c and is a +companion document to Documentation/devicetree/dt-object-internal.txt[1] & +Documentation/devicetree/dynamic-resolution-notes.txt[2] + +How overlays work +----------------- + +A Device Tree's overlay purpose is to modify the kernel's live tree, and +have the modification affecting the state of the the kernel in a way that +is reflecting the changes. +Since the kernel mainly deals with devices, any new device node that result +in an active device should have it created while if the device node is either +disabled or removed all together, the affected device should be deregistered. + +Lets take an example where we have a foo board with the following base tree +which is taken from [1]. + +---- foo.dts ----------------------------------------------------------------- + /* FOO platform */ + / { + compatible = "corp,foo"; + + /* shared resources */ + res: res { + }; + + /* On chip peripherals */ + ocp: ocp { + /* peripherals that are always instantiated */ + peripheral1 { ... }; + } + }; +---- foo.dts ----------------------------------------------------------------- + +The overlay bar.dts, when loaded (and resolved as described in [2]) should + +---- bar.dts ----------------------------------------------------------------- +/plugin/; /* allow undefined label references and record them */ +/ { + .... /* various properties for loader use; i.e. part id etc. */ + fragment@0 { + target = <&ocp>; + __overlay__ { + /* bar peripheral */ + bar { + compatible = "corp,bar"; + ... /* various properties and child nodes */ + } + }; + }; +}; +---- bar.dts ----------------------------------------------------------------- + +result in foo+bar.dts + +---- foo+bar.dts ------------------------------------------------------------- + /* FOO platform + bar peripheral */ + / { + compatible = "corp,foo"; + + /* shared resources */ + res: res { + }; + + /* On chip peripherals */ + ocp: ocp { + /* peripherals that are always instantiated */ + peripheral1 { ... }; + + /* bar peripheral */ + bar { + compatible = "corp,bar"; + ... /* various properties and child nodes */ + } + } + }; +---- foo+bar.dts ------------------------------------------------------------- + +As a result of the the overlay, a new device node (bar) has been created +so a bar platform device will be registered and if a matching device driver +is loaded the device will be created as expected. + +Overlay in-kernel API +-------------------------------- + +The API is quite easy to use. + +1. Call of_overlay_create() to create and apply an overlay. The return value +is a cookie identifying this overlay. + +2. Call of_overlay_destroy() to remove and cleanup the overlay previously +created via the call to of_overlay_create(). Removal of an overlay that +is stacked by another will not be permitted. + +Finally, if you need to remove all overlays in one-go, just call +of_overlay_destroy_all() which will remove every single one in the correct +order. + +Overlay DTS Format +------------------ + +The DTS of an overlay should have the following format: + +{ + /* ignored properties by the overlay */ + + fragment@0 { /* first child node */ + + target=<phandle>; /* phandle target of the overlay */ + or + target-path="/path"; /* target path of the overlay */ + + __overlay__ { + property-a; /* add property-a to the target */ + node-a { /* add to an existing, or create a node-a */ + ... + }; + }; + } + fragment@1 { /* second child node */ + ... + }; + /* more fragments follow */ +} + +Using the non-phandle based target method allows one to use a base DT which does +not contain a __symbols__ node, i.e. it was not compiled with the -@ option. +The __symbols__ node is only required for the target=<phandle> method, since it +contains the information required to map from a phandle to a tree location. diff --git a/Documentation/devicetree/todo.txt b/Documentation/devicetree/todo.txt index c3cf0659bd19..b5139d1de811 100644 --- a/Documentation/devicetree/todo.txt +++ b/Documentation/devicetree/todo.txt @@ -2,7 +2,6 @@ Todo list for devicetree: === General structure === - Switch from custom lists to (h)list_head for nodes and properties structure -- Remove of_allnodes list and iterate using list of child nodes alone === CONFIG_OF_DYNAMIC === - Switch to RCU for tree updates and get rid of global spinlock |