diff options
Diffstat (limited to 'Documentation/devicetree')
68 files changed, 1663 insertions, 90 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt new file mode 100644 index 000000000000..885f93d14ef9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -0,0 +1,49 @@ +Altera SoCFPGA ECC Manager +This driver uses the EDAC framework to implement the SOCFPGA ECC Manager. +The ECC Manager counts and corrects single bit errors and counts/handles +double bit errors which are uncorrectable. + +Required Properties: +- compatible : Should be "altr,socfpga-ecc-manager" +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges : standard definition, should translate from local addresses + +Subcomponents: + +L2 Cache ECC +Required Properties: +- compatible : Should be "altr,socfpga-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +On Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-ocram-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- iram : phandle to On-Chip RAM definition. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +Example: + + eccmgr: eccmgr@ffd08140 { + compatible = "altr,socfpga-ecc-manager"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + l2-ecc@ffd08140 { + compatible = "altr,socfpga-l2-ecc"; + reg = <0xffd08140 0x4>; + interrupts = <0 36 1>, <0 37 1>; + }; + + ocram-ecc@ffd08144 { + compatible = "altr,socfpga-ocram-ecc"; + reg = <0xffd08144 0x4>; + iram = <&ocram>; + interrupts = <0 178 1>, <0 179 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index a2bd593881ca..66422d663184 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -23,6 +23,7 @@ Optional properties: during suspend. - ti,no-reset-on-init: When present, the module should not be reset at init - ti,no-idle-on-init: When present, the module should not be idled at init +- ti,no-idle: When present, the module is never allowed to idle. Example: diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt index ace05992a262..20df350b9ef3 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt @@ -30,7 +30,7 @@ that they are defined using standard clock bindings with following clock-output-names: - "xin24m" - crystal input - required, - "ext_i2s" - external I2S clock - optional, - - "ext_gmac" - external GMAC clock - optional + - "rmii_clkin" - external EMAC clock - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78e2a31c58d0..1006b0489464 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -16,6 +16,10 @@ Required properties: - regmap-mcba : Regmap of the MCB-A (memory bridge) resource. - regmap-mcbb : Regmap of the MCB-B (memory bridge) resource. - regmap-efuse : Regmap of the PMD efuse resource. +- regmap-rb : Regmap of the register bus resource. This property + is optional only for compatibility. If the RB + error conditions are not cleared, it will + continuously generate interrupt. - reg : First resource shall be the CPU bus (PCP) resource. - interrupts : Interrupt-specifier for MCU, PMD, L3, or SoC error IRQ(s). @@ -64,6 +68,11 @@ Example: reg = <0x0 0x1054a000 0x0 0x20>; }; + rb: rb@7e000000 { + compatible = "apm,xgene-rb", "syscon"; + reg = <0x0 0x7e000000 0x0 0x10>; + }; + edac@78800000 { compatible = "apm,xgene-edac"; #address-cells = <2>; @@ -73,6 +82,7 @@ Example: regmap-mcba = <&mcba>; regmap-mcbb = <&mcbb>; regmap-efuse = <&efuse>; + regmap-rb = <&rb>; reg = <0x0 0x78800000 0x0 0x100>; interrupts = <0x0 0x20 0x4>, <0x0 0x21 0x4>, diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 000000000000..ef3752889496 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&PBCLK4>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt new file mode 100644 index 000000000000..0863e067c85b --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt @@ -0,0 +1,20 @@ +Bindings for the fan / temperature monitor microcontroller used on +the Zyxel NSA 320 and several subsequent models. + +Required properties: +- compatible : "zyxel,nsa320-mcu" +- data-gpios : The GPIO pin connected to the data line on the MCU +- clk-gpios : The GPIO pin connected to the clock line on the MCU +- act-gpios : The GPIO pin connected to the active line on the MCU + +Example: + + hwmon { + compatible = "zyxel,nsa320-mcu"; + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>; + pinctrl-names = "default"; + + data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index a04a80f9cc70..c3b9c4cfe8df 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -10,6 +10,7 @@ Requires node properties: "murata,ncp03wb473" "murata,ncp15wl333" "murata,ncp03wf104" + "murata,ncp15xh103" /* Usage of vendor name "ntc" is deprecated */ <DEPRECATED> "ntc,ncp15wb473" diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt index 0b447d9ad196..68d6f8ce063b 100644 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -82,7 +82,7 @@ vdd channel is connected to output 0 of the &ref device. ... - iio_hwmon { + iio-hwmon { compatible = "iio-hwmon"; io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>, <&adc 5>, diff --git a/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt new file mode 100644 index 000000000000..f6f1c14bf99b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt @@ -0,0 +1,26 @@ +Alpine MSIX controller + +See arm,gic-v3.txt for SPI and MSI definitions. + +Required properties: + +- compatible: should be "al,alpine-msix" +- reg: physical base address and size of the registers +- interrupt-parent: specifies the parent interrupt controller. +- interrupt-controller: identifies the node as an interrupt controller +- msi-controller: identifies the node as an PCI Message Signaled Interrupt + controller +- al,msi-base-spi: SPI base of the MSI frame +- al,msi-num-spis: number of SPIs assigned to the MSI frame, relative to SPI0 + +Example: + +msix: msix { + compatible = "al,alpine-msix"; + reg = <0x0 0xfbe00000 0x0 0x100000>; + interrupt-parent = <&gic>; + interrupt-controller; + msi-controller; + al,msi-base-spi = <160>; + al,msi-num-spis = <160>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 7803e77d85cb..007a5b46256a 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -24,9 +24,8 @@ Main node required properties: 1 = edge triggered 4 = level triggered - Cells 4 and beyond are reserved for future use. When the 1st cell - has a value of 0 or 1, cells 4 and beyond act as padding, and may be - ignored. It is recommended that padding cells have a value of 0. + Cells 4 and beyond are reserved for future use and must have a value + of 0 if present. - reg : Specifies base physical address(s) and size of the GIC registers, in the following order: diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 5a1cb4bc3dfe..793c20ff8fcc 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -16,6 +16,7 @@ Main node required properties: "arm,cortex-a15-gic" "arm,cortex-a7-gic" "arm,cortex-a9-gic" + "arm,eb11mp-gic" "arm,gic-400" "arm,pl390" "arm,tc11mp-gic" diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt new file mode 100644 index 000000000000..8af0a8e613ab --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -0,0 +1,44 @@ + +* Marvell ODMI for MSI support + +Some Marvell SoCs have an On-Die Message Interrupt (ODMI) controller +which can be used by on-board peripheral for MSI interrupts. + +Required properties: + +- compatible : The value here should contain: + + "marvell,ap806-odmi-controller", "marvell,odmi-controller". + +- interrupt,controller : Identifies the node as an interrupt controller. + +- msi-controller : Identifies the node as an MSI controller. + +- marvell,odmi-frames : Number of ODMI frames available. Each frame + provides a number of events. + +- reg : List of register definitions, one for each + ODMI frame. + +- marvell,spi-base : List of GIC base SPI interrupts, one for each + ODMI frame. Those SPI interrupts are 0-based, + i.e marvell,spi-base = <128> will use SPI #96. + See Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt + for details about the GIC Device Tree binding. + +- interrupt-parent : Reference to the parent interrupt controller. + +Example: + + odmi: odmi@300000 { + compatible = "marvell,ap806-odm-controller", + "marvell,odmi-controller"; + interrupt-controller; + msi-controller; + marvell,odmi-frames = <4>; + reg = <0x300000 0x4000>, + <0x304000 0x4000>, + <0x308000 0x4000>, + <0x30C000 0x4000>; + marvell,spi-base = <128>, <136>, <144>, <152>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt index aae4c384ee1f..173595305e26 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -23,6 +23,12 @@ Optional properties: - mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors to which the GIC may not route interrupts. Valid values are 2 - 7. This property is ignored if the CPU is started in EIC mode. +- mti,reserved-ipi-vectors : Specifies the range of GIC interrupts that are + reserved for IPIs. + It accepts 2 values, the 1st is the starting interrupt and the 2nd is the size + of the reserved range. + If not specified, the driver will allocate the last 2 * number of VPEs in the + system. Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". @@ -44,6 +50,7 @@ Example: #interrupt-cells = <3>; mti,reserved-cpu-vectors = <7>; + mti,reserved-ipi-vectors = <40 8>; timer { compatible = "mti,gic-timer"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt new file mode 100644 index 000000000000..1f441fa0ad40 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt @@ -0,0 +1,49 @@ +Sigma Designs SMP86xx/SMP87xx secondary interrupt controller + +Required properties: +- compatible: should be "sigma,smp8642-intc" +- reg: physical address of MMIO region +- ranges: address space mapping of child nodes +- interrupt-parent: phandle of parent interrupt controller +- interrupt-controller: boolean +- #address-cells: should be <1> +- #size-cells: should be <1> + +One child node per control block with properties: +- reg: address of registers for this control block +- interrupt-controller: boolean +- #interrupt-cells: should be <2>, interrupt index and flags per interrupts.txt +- interrupts: interrupt spec of primary interrupt controller + +Example: + +interrupt-controller@6e000 { + compatible = "sigma,smp8642-intc"; + reg = <0x6e000 0x400>; + ranges = <0x0 0x6e000 0x400>; + interrupt-parent = <&gic>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <1>; + + irq0: interrupt-controller@0 { + reg = <0x000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq1: interrupt-controller@100 { + reg = <0x100 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq2: interrupt-controller@300 { + reg = <0x300 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt new file mode 100644 index 000000000000..926c2117942c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt @@ -0,0 +1,52 @@ +Binding for ISSI IS31FL32xx and Si-En SN32xx LED Drivers + +The IS31FL32xx/SN32xx family of LED drivers are I2C devices with multiple +constant-current channels, each with independent 256-level PWM control. +Each LED is represented as a sub-node of the device. + +Required properties: +- compatible: one of + issi,is31fl3236 + issi,is31fl3235 + issi,is31fl3218 + issi,is31fl3216 + si-en,sn3218 + si-en,sn3216 +- reg: I2C slave address +- address-cells : must be 1 +- size-cells : must be 0 + +LED sub-node properties: +- reg : LED channel number (1..N) +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + + +Example: + +is31fl3236: led-controller@3c { + compatible = "issi,is31fl3236"; + reg = <0x3c>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + label = "EB:blue:usr0"; + }; + led@2 { + reg = <2>; + label = "EB:blue:usr1"; + }; + ... + led@36 { + reg = <36>; + label = "EB:blue:usr35"; + }; +}; + +For more product information please see the links below: +http://www.issi.com/US/product-analog-fxled-driver.shtml +http://www.si-en.com/product.asp?parentid=890 diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt index 202565313e82..100f0ae43269 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -20,6 +20,8 @@ Optional Properties: - link-frequencies: List of allowed link frequencies in Hz. Each frequency is expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt new file mode 100644 index 000000000000..8c0fc1a26bf0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -0,0 +1,45 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +- compatible: value must be "ti,tvp5150" +- reg: I2C slave address + +Optional Properties: +- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Endpoint Properties for parallel synchronization: + +- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: field signal level during the even field data + transmission. Must be <0>. + +If none of hsync-active, vsync-active and field-even-active is specified, +the endpoint is assumed to use embedded BT.656 synchronization. + +Example: + +&i2c2 { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + + port { + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 9dafe6b06cd2..619193ccf7ff 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -6,6 +6,7 @@ family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - compatible: Must be one of the following + - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device - "renesas,vin-r8a7791" for the R8A7791 device diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt index 0cb94201bf92..d3436e5190f9 100644 --- a/Documentation/devicetree/bindings/media/renesas,jpu.txt +++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt @@ -5,11 +5,12 @@ and decoding function conforming to the JPEG baseline process, so that the JPU can encode image data and decode JPEG data quickly. Required properties: - - compatible: should containg one of the following: - - "renesas,jpu-r8a7790" for R-Car H2 - - "renesas,jpu-r8a7791" for R-Car M2-W - - "renesas,jpu-r8a7792" for R-Car V2H - - "renesas,jpu-r8a7793" for R-Car M2-N +- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback. + Examples with soctypes are: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N - reg: Base address and length of the registers block for the JPU. - interrupts: JPU interrupt specifier. @@ -17,7 +18,7 @@ Required properties: Example: R8A7790 (R-Car H2) JPU node jpeg-codec@fe980000 { - compatible = "renesas,jpu-r8a7790"; + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; reg = <0 0xfe980000 0 0x10300>; interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_JPU>; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 87fe08abf36d..627405abd144 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -1,30 +1,18 @@ -* Renesas VSP1 Video Processing Engine +* Renesas VSP Video Processing Engine -The VSP1 is a video processing engine that supports up-/down-scaling, alpha +The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. It can be found in the Renesas R-Car second generation SoCs. Required properties: - - compatible: Must contain "renesas,vsp1" + - compatible: Must contain one of the following values + - "renesas,vsp1" for the R-Car Gen2 VSP1 + - "renesas,vsp2" for the R-Car Gen3 VSP2 - - reg: Base address and length of the registers block for the VSP1. - - interrupts: VSP1 interrupt specifier. - - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. - - - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. - - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. - - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. - - -Optional properties: - - - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is - available. - - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is - available. - - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) - module is available. + - reg: Base address and length of the registers block for the VSP. + - interrupts: VSP interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP functional clock. Example: R8A7790 (R-Car H2) VSP1-S node @@ -34,10 +22,4 @@ Example: R8A7790 (R-Car H2) VSP1-S node reg = <0 0xfe928000 0 0x8000>; interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; - - renesas,has-lut; - renesas,has-sru; - renesas,#rpf = <5>; - renesas,#uds = <3>; - renesas,#wpf = <4>; }; diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt new file mode 100644 index 000000000000..ae9b52f37576 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-cal.txt @@ -0,0 +1,72 @@ +Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) +------------------------------------------------------ + +The Camera Adaptation Layer (CAL) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect CSI2 image-sensor modules to the +DRA72x device. + +Required properties: +- compatible: must be "ti,dra72-cal" +- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX + control address space +- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control + registers +- interrupts: should contain IRQ line for the CAL; + +CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes +should contain a 'port' child node with child 'endpoint' node. Please +refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + ti,hwmods = "cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>, + <0x4A002e94 0x4>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1", + "camerrx_control"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + endpoint { + slave-mode; + remote-endpoint = <&ar0330_1>; + }; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + + i2c5: i2c@4807c000 { + ar0330@10 { + compatible = "ti,ar0330"; + reg = <0x10>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ar0330_1: endpoint { + reg = <0>; + clock-lanes = <1>; + data-lanes = <0 2 3 4>; + remote-endpoint = <&csi2_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 451fef26b4df..10587bdadbbe 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -68,7 +68,7 @@ ethernet@f0b60000 { phy1: ethernet-phy@1 { max-speed = <1000>; reg = <0x1>; - compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22"; + compatible = "ethernet-phy-ieee802.3-c22"; }; }; }; @@ -115,7 +115,7 @@ ethernet@f0ba0000 { phy0: ethernet-phy@0 { max-speed = <1000>; reg = <0x0>; - compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22"; + compatible = "ethernet-phy-ieee802.3-c22"; }; }; }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index 80411b2f0490..ecacfa44b1eb 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -4,8 +4,6 @@ Required properties: - compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2". "hisilicon,hns-dsaf-v1" is for hip05. "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612. -- dsa-name: dsa fabric name who provide this interface. - should be "dsafX", X is the dsaf id. - mode: dsa fabric mode string. only support one of dsaf modes like these: "2port-64vf", "6port-16rss", @@ -26,9 +24,8 @@ Required properties: Example: -dsa: dsa@c7000000 { +dsaf0: dsa@c7000000 { compatible = "hisilicon,hns-dsaf-v1"; - dsa_name = "dsaf0"; mode = "6port-16rss"; interrupt-parent = <&mbigen_dsa>; reg = <0x0 0xC0000000 0x0 0x420000 diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index 41d19be7011e..e6a9d1c30878 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -4,8 +4,9 @@ Required properties: - compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2". "hisilicon,hns-nic-v1" is for hip05. "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612. -- ae-name: accelerator name who provides this interface, - is simply a name referring to the name of name in the accelerator node. +- ae-handle: accelerator engine handle for hns, + specifies a reference to the associating hardware driver node. + see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt - port-id: is the index of port provided by DSAF (the accelerator). DSAF can connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They are called debug ports. @@ -41,7 +42,7 @@ Example: ethernet@0{ compatible = "hisilicon,hns-nic-v1"; - ae-name = "dsaf0"; + ae-handle = <&dsaf0>; port-id = <0>; local-mac-address = [a2 14 e4 4b 56 76]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index aeea50c84e92..d0cb8693963b 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -6,12 +6,17 @@ Required properties: - interrupts: interrupt for the device - phy: See ethernet.txt file in the same directory. - phy-mode: See ethernet.txt file in the same directory -- clocks: a pointer to the reference clock for this device. +- clocks: List of clocks for this device. At least one clock is + mandatory for the core clock. If several clocks are given, then the + clock-names property must be used to identify them. Optional properties: - tx-csum-limit: maximum mtu supported by port that allow TX checksum. Value is presented in bytes. If not used, by default 1600B is set for "marvell,armada-370-neta" and 9800B for others. +- clock-names: List of names corresponding to clocks property; shall be + "core" for core clock and "bus" for the optional bus clock. + Example: diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt index 79384113c2b0..694987d3c17a 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt @@ -38,7 +38,6 @@ Example : phy11: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -48,7 +47,6 @@ Example : }; phy12: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -58,7 +56,6 @@ Example : }; phy13: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -68,7 +65,6 @@ Example : }; phy14: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -85,7 +81,6 @@ Example : phy21: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -95,7 +90,6 @@ Example : }; phy22: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -105,7 +99,6 @@ Example : }; phy23: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -115,7 +108,6 @@ Example : }; phy24: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt index f65606f8d632..491f5bd55203 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -47,7 +47,6 @@ Example : phy11: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -57,7 +56,6 @@ Example : }; phy12: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -67,7 +65,6 @@ Example : }; phy13: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -77,7 +74,6 @@ Example : }; phy14: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -94,7 +90,6 @@ Example : phy21: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -104,7 +99,6 @@ Example : }; phy22: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -114,7 +108,6 @@ Example : }; phy23: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -124,7 +117,6 @@ Example : }; phy24: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 525e1658f2da..bc1c3c8bf8fa 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -17,8 +17,7 @@ Optional Properties: "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 specifications. If neither of these are specified, the default is to - assume clause 22. The compatible list may also contain other - elements. + assume clause 22. If the phy's identifier is known then the list may contain an entry of the form: "ethernet-phy-idAAAA.BBBB" where @@ -28,6 +27,9 @@ Optional Properties: 4 hex digits. This is the chip vendor OUI bits 19:24, followed by 10 bits of a vendor specific ID. + The compatible list should not contain other values than those + listed here. + - max-speed: Maximum PHY supported speed (10, 100, 1000...) - broken-turn-around: If set, indicates the PHY device does not correctly diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 81a9f9e6b45f..c8ac222eac67 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -82,8 +82,8 @@ Example: "ch16", "ch17", "ch18", "ch19", "ch20", "ch21", "ch22", "ch23", "ch24"; - clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>; - power-domains = <&cpg_clocks>; + clocks = <&cpg CPG_MOD 812>; + power-domains = <&cpg>; phy-mode = "rgmii-id"; phy-handle = <&phy0>; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5b0853df9d5a..64f2fff12128 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -28,3 +28,20 @@ Optional properties: - clock-names: Must include the following entries: - "pcie" - "pcie_bus" + +Example configuration: + + pcie: pcie@0xdffff000 { + compatible = "snps,dw-pcie"; + reg = <0xdffff000 0x1000>, /* Controller registers */ + <0xd0000000 0x2000>; /* PCI config space */ + reg-names = "ctrlreg", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000 + 0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; + interrupts = <25>, <24>; + #interrupt-cells = <1>; + num-lanes = <1>; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 6fbba53a309b..3be80c68941a 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -13,6 +13,13 @@ Required properties: - clock-names: Must include the following additional entries: - "pcie_phy" +Optional properties: +- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 +- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 +- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 + Example: pcie@0x01000000 { diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 4e8b90e43dd8..07a75094c5a8 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -8,6 +8,7 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7793" for the R8A7793 SoC; "renesas,pci-r8a7794" for the R8A7794 SoC; "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt new file mode 100644 index 000000000000..f478874b79ce --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt @@ -0,0 +1,30 @@ +* ThunderX PCI host controller for pass-1.x silicon + +Firmware-initialized PCI host controller to on-chip devices found on +some Cavium ThunderX processors. These devices have ECAM-based config +access, but the BARs are all at fixed addresses. We handle the fixed +addresses by synthesizing Enhanced Allocation (EA) capabilities for +these devices. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-ecam" + +Example: + + pcie@84b000000000 { + compatible = "cavium,pci-host-thunder-ecam"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x30000 0x10000>; + bus-range = <0 31>; + #size-cells = <2>; + #address-cells = <3>; + #stream-id-cells = <1>; + reg = <0x84b0 0x00000000 0 0x02000000>; /* Configuration space */ + ranges = <0x03000000 0x8180 0x00000000 0x8180 0x00000000 0x80 0x00000000>; /* mem ranges */ + }; diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt new file mode 100644 index 000000000000..f131faea3b7c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt @@ -0,0 +1,43 @@ +* ThunderX PEM PCIe host controller + +Firmware-initialized PCI host controller found on some Cavium +ThunderX processors. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-pem" + +- reg : Two entries: First the configuration space for down + stream devices base address and size, as accessed + from the parent bus. Second, the register bank of + the PEM device PCIe bridge. + +Example: + + pci@87e0,c2000000 { + compatible = "cavium,pci-host-thunder-pem"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x10000 0x10000>; + bus-range = <0x8f 0xc7>; + #size-cells = <2>; + #address-cells = <3>; + + reg = <0x8880 0x8f000000 0x0 0x39000000>, /* Configuration space */ + <0x87e0 0xc2000000 0x0 0x00010000>; /* PEM space */ + ranges = <0x01000000 0x00 0x00020000 0x88b0 0x00020000 0x00 0x00010000>, /* I/O */ + <0x03000000 0x00 0x10000000 0x8890 0x10000000 0x0f 0xf0000000>, /* mem64 */ + <0x43000000 0x10 0x00000000 0x88a0 0x00000000 0x10 0x00000000>, /* mem64-pref */ + <0x03000000 0x87e0 0xc2f00000 0x87e0 0xc2000000 0x00 0x00100000>; /* mem64 PEM BAR4 */ + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic0 0 0 0 24 4>, /* INTA */ + <0 0 0 2 &gic0 0 0 0 25 4>, /* INTB */ + <0 0 0 3 &gic0 0 0 0 26 4>, /* INTC */ + <0 0 0 4 &gic0 0 0 0 27 4>; /* INTD */ + }; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 558fe528ae19..6cf99690eef9 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -4,6 +4,7 @@ Required properties: compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; + "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt new file mode 100644 index 000000000000..337fc97d18c9 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -0,0 +1,68 @@ +* Xilinx NWL PCIe Root Port Bridge DT description + +Required properties: +- compatible: Should contain "xlnx,nwl-pcie-2.11" +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- reg: Should contain Bridge, PCIe Controller registers location, + configuration space, and length +- reg-names: Must include the following entries: + "breg": bridge registers + "pcireg": PCIe controller registers + "cfg": configuration space region +- device_type: must be "pci" +- interrupts: Should contain NWL PCIe interrupt +- interrupt-names: Must include the following entries: + "msi1, msi0": interrupt asserted when MSI is received + "intx": interrupt asserted when a legacy interrupt is received + "misc": interrupt asserted when miscellaneous is received +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation +- msi-controller: indicates that this is MSI controller node +- msi-parent: MSI parent of the root complex itself +- legacy-interrupt-controller: Interrupt controller device node for Legacy interrupts + - interrupt-controller: identifies the node as an interrupt controller + - #interrupt-cells: should be set to 1 + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + +Example: +++++++++ + +nwl_pcie: pcie@fd0e0000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "xlnx,nwl-pcie-2.11"; + #interrupt-cells = <1>; + msi-controller; + device_type = "pci"; + interrupt-parent = <&gic>; + interrupts = <0 114 4>, <0 115 4>, <0 116 4>, <0 117 4>, <0 118 4>; + interrupt-names = "msi0", "msi1", "intx", "dummy", "misc"; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, + <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, + <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, + <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; + + msi-parent = <&nwl_pcie>; + reg = <0x0 0xfd0e0000 0x0 0x1000>, + <0x0 0xfd480000 0x0 0x1000>, + <0x0 0xe0000000 0x0 0x1000000>; + reg-names = "breg", "pcireg", "cfg"; + ranges = <0x02000000 0x00000000 0xe1000000 0x00000000 0xe1000000 0 0x0f000000>; + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + +}; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt index 02f979a48aeb..fd57a81180a4 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -17,7 +17,7 @@ Required properties: Please refer to the standard PCI bus binding document for a more detailed explanation -Optional properties: +Optional properties for Zynq/Microblaze: - bus-range: PCI bus numbers covered Interrupt controller child node @@ -38,13 +38,13 @@ the four INTx interrupts in ISR and route them to this domain. Example: ++++++++ - +Zynq: pci_express: axi-pcie@50000000 { #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; compatible = "xlnx,axi-pcie-host-1.00.a"; - reg = < 0x50000000 0x10000000 >; + reg = < 0x50000000 0x1000000 >; device_type = "pci"; interrupts = < 0 52 4 >; interrupt-map-mask = <0 0 0 7>; @@ -60,3 +60,29 @@ Example: #interrupt-cells = <1>; }; }; + + +Microblaze: + pci_express: axi-pcie@10000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = <0x10000000 0x4000000>; + device_type = "pci"; + interrupt-parent = <µblaze_0_intc>; + interrupts = <1 2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x10000000>; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + }; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9213b27e1036..69617220c5d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -21,6 +21,8 @@ Required properties: "allwinner,sun9i-a80-r-pinctrl" "allwinner,sun8i-a83t-pinctrl" "allwinner,sun8i-h3-pinctrl" + "allwinner,sun8i-h3-r-pinctrl" + "allwinner,sun50i-a64-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt new file mode 100644 index 000000000000..e295dda4bbba --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt @@ -0,0 +1,102 @@ +Broadcom Northstar2 IOMUX Controller + +The Northstar2 IOMUX controller supports group based mux configuration. There +are some individual pins that support modifying the pinconf parameters. + +Required properties: + +- compatible: + Must be "brcm,ns2-pinmux" + +- reg: + Define the base and range of the I/O address space that contains the + Northstar2 IOMUX and pin configuration registers. + +Properties in sub nodes: + +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +- pins: + List of pin names to change configuration + +The generic properties bias-disable, bias-pull-down, bias-pull-up, +drive-strength, slew-rate, input-enable, input-disable are supported +for some individual pins listed at the end. + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinctrl: pinctrl@6501d130 { + compatible = "brcm,ns2-pinmux"; + reg = <0x6501d130 0x08>, + <0x660a0028 0x04>, + <0x660009b0 0x40>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel &uart3_rx &sdio0_d4>; + + /* Select nand function */ + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + + /* Pull up the uart3 rx pin */ + uart3_rx: uart3_rx { + pins = "uart3_sin"; + bias-pull-up; + }; + + /* Set the drive strength of sdio d4 pin */ + sdio0_d4: sdio0_d4 { + pins = "sdio0_data4"; + drive-strength = <8>; + }; + }; + +List of supported functions and groups in Northstar2: + +"nand": "nand_grp" + +"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp", + "nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp", + "nor_addr_12_15_grp" + +"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp", + "gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp", + "gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp", + "gpio_28_29_grp", "gpio_30_31_grp" + +"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp", + "pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp" + +"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp" + +"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp", + "uart1_rts_cts_grp", "uart1_in_out_grp" + +"uart2": "uart2_rts_cts_grp" + +"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp" + + +List of pins that support pinconf parameters: + +"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout", +"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck", +"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7", +"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4", +"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1", +"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk", +"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1", +"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk", +"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc", +"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent", +"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc", +"usb2_overcurrent", "sata_led1", "sata_led0" diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt new file mode 100644 index 000000000000..4b5efa51bec7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -0,0 +1,60 @@ +* Microchip PIC32 Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +PIC32 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configuraions of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "microchip,pic32mada-pinctrl" + - reg: Address range of the pinctrl registers. + - clocks: Clock specifier (see clock bindings for details) + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - input-enable: Set the pin as an input. + - output-low: Set the pin as an output level low. + - output-high: Set the pin as an output level high. + - microchip,digital: Enable digital I/O. + - microchip,analog: Enable analog I/O. + +Example: + +pic32_pinctrl: pinctrl@1f801400{ + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,pic32mzda-pinctrl"; + reg = <0x1f801400 0x400>; + clocks = <&PBCLK1>; + + pinctrl_uart2: pinctrl_uart2 { + uart2-tx { + pins = "G9"; + function = "U2TX"; + microchip,digital; + output-low; + }; + uart2-rx { + pins = "B0"; + function = "U2RX"; + microchip,digital; + input-enable; + }; + }; +}; + +uart2: serial@1f822200 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822200 0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt index df0309c57505..bd8b0c69fa44 100644 --- a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt +++ b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt @@ -22,6 +22,10 @@ The following generic nodes are supported: - input-schmitt-disable - slew-rate +NXP specific properties: + - nxp,gpio-pin-interrupt : Assign pin to gpio pin interrupt controller + irq number 0 to 7. See example below. + Not all pins support all properties so either refer to the NXP 1850/4350 user manual or the pin table in the pinctrl-lpc18xx driver for supported pin properties. @@ -54,4 +58,14 @@ pinctrl: pinctrl@40086000 { bias-disable; }; }; + + gpio_joystick_pins: gpio-joystick-pins { + gpio_joystick_1_cfg { + pins = "p9_0"; + function = "gpio"; + nxp,gpio-pin-interrupt = <0>; + input-enable; + bias-disable; + }; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 9ffb0b276bb4..17631d0a9af7 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -6,6 +6,7 @@ Required properties: - compatible: value should be one of the following. "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl. "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl. + "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl. "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl. "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. "mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt new file mode 100644 index 000000000000..cfb8500dd56b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt @@ -0,0 +1,74 @@ +Qualcomm Atheros IPQ4019 TLMM block + +This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019 +platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities. + +Required properties: +- compatible: "qcom,ipq4019-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength. + +Non-empty subnodes must specify the 'pins' property. +Note that not all properties are valid for all pins. + + +Valid values for qcom,pins are: + gpio0-gpio99 + Supports mux, bias and drive-strength + +Valid values for qcom,function are: +gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq4019-pinctrl"; + reg = <0x1000000 0x300000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 0cd701b1947f..c68b9554561f 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -22,7 +22,7 @@ Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl" + "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt new file mode 100644 index 000000000000..7b4800cc251e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -0,0 +1,126 @@ +* STM32 GPIO and Pin Mux/Config controller + +STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pins and +also provides ability to multiplex and configure the output of various on-chip +controllers onto these pads. + +Pin controller node: +Required properies: + - compatible: value should be one of the following: + (a) "st,stm32f429-pinctrl" + - #address-cells: The value of this property must be 1 + - #size-cells : The value of this property must be 1 + - ranges : defines mapping between pin controller node (parent) to + gpio-bank node (children). + - pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. + +GPIO controller/bank node: +Required properties: + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Should be two. + The first cell is the pin number + The second one is the polarity: + - 0 for active high + - 1 for active low + - reg : The gpio address range, relative to the pinctrl range + - clocks : clock that drives this bank + - st,bank-name : Should be a name string for this bank as specified in + the datasheet + +Optional properties: + - reset: : Reference to the reset controller + +Example: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + }; + ... + pin-functions nodes follow... + }; + +Contents of function subnode node: +---------------------------------- +Subnode format +A pinctrl node should contain at least one subnode representing the +pinctrl group available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive, output high/low and output speed. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined in + dt-bindings/pinctrl/<soc>-pinfunc.h directly. + These defines are calculated as: + ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use. + Available options are: + - bias-disable, + - bias-pull-down, + - bias-pull-up, + - drive-push-pull, + - drive-open-drain, + - output-low + - output-high + - slew-rate = <x>, with x being: + < 0 > : Low speed + < 1 > : Medium speed + < 2 > : Fast speed + < 3 > : High speed + +Example: + +pin-controller { +... + usart1_pins_a: usart1@0 { + pins1 { + pinmux = <STM32F429_PA9_FUNC_USART1_TX>; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32F429_PA10_FUNC_USART1_RX>; + bias-disable; + }; + }; +}; + +&usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index b494f8b8ef72..e98a9652ccc8 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -5,15 +5,18 @@ Index Device Endianness properties --------------------------------------------------- 1 BE 'big-endian' 2 LE 'little-endian' +3 Native 'native-endian' For one device driver, which will run in different scenarios above on different SoCs using the devicetree, we need one way to simplify this. -Required properties: -- {big,little}-endian: these are boolean properties, if absent - meaning that the CPU and the Device are in the same endianness mode, - these properties are for register values and all the buffers only. +Optional properties: +- {big,little,native}-endian: these are boolean properties, if absent + then the implementation will choose a default based on the device + being controlled. These properties are for register values and all + the buffers only. Native endian means that the CPU and device have + the same endianness. Examples: Scenario 1 : CPU in LE mode & device in LE mode. diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt new file mode 100644 index 000000000000..5c80a7779552 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -0,0 +1,80 @@ +Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + +Optional properties: +- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high. + If this property is missing, assume the VSEL pin is set to logic-low. + +Optional input supply properties: + - vp1-supply: The input supply for REG_DCDC1 + - vp2-supply: The input supply for REG_DCDC2 + - vp3-supply: The input supply for REG_DCDC3 + - inl45-supply: The input supply for REG_LDO1 and REG_LDO2 + - inl67-supply: The input supply for REG_LDO3 and REG_LDO4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..14cfdc564159 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,29 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The Hi655x regulator control is managed by Hi655x PMIC. +So the node of this regulator must be child node of Hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8 +LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt index 78183182dad9..ca58a68ffdf1 100644 --- a/Documentation/devicetree/bindings/regulator/lp872x.txt +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -28,6 +28,7 @@ Optional properties: - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + - enable-gpios: GPIO specifier for EN pin control of LP872x devices. Sub nodes for regulator_init_data LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 09d796ed48be..879e98d3b9aa 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are: 1: Normal regulator voltage output mode. 3: Low Power which reduces the quiescent current down to only 1uA -The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h header and can be included by device tree source files. The standard "regulator-mode" property can only be used for regulators that diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt new file mode 100644 index 000000000000..b3c8ca672024 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -0,0 +1,200 @@ +Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. + +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply +of these regulators are defined under parent device node. +Details of regulator properties are defined as child node under +sub-node "regulators" which is child node of device node. + +Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt> +for common regulator bindings used by client. + +Following are properties of parent node related to regulators. + +Optional properties: +------------------- +The input supply of regulators are the optional properties on the +parent device node. The input supply of these regulators are provided +through following properties: +in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. +in-sd1-supply: Input supply for SD1. +in-sd2-supply: Input supply for SD2. +in-sd3-supply: Input supply for SD3. +in-ldo0-1-supply: Input supply for LDO0 and LDO1. +in-ldo2-supply: Input supply for LDO2. +in-ldo3-5-supply: Input supply for LDO3 and LDO5 +in-ldo4-6-supply: Input supply for LDO4 and LDO6. +in-ldo7-8-supply: Input supply for LDO7 and LDO8. + +Optional sub nodes for regulators under "regulators" subnode: +------------------------------------------------------------ +The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + +Each sub-node should contain the constraints and initialization +information for that regulator. The definition for each of these +nodes is defined using the standard binding for regulators found at +<Documentation/devicetree/bindings/regulator/regulator.txt>. + +Theres are also additional properties for SD/LDOs. These additional properties +are required to configure FPS configuration parameters for SDs and LDOs. +Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible +Power Sequence (FPS). +Following are additional properties: + +- maxim,active-fps-source: FPS source for the regulators to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + Regulator is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + regulator to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the regulator get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the regulator get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + regulators { + sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + }; + + sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 1d112fc456aa..ecfc593cac15 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -44,6 +44,11 @@ Optional properties: any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. - regulator-over-current-protection: Enable over current protection. +- regulator-active-discharge: tristate, enable/disable active discharge of + regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index d18109657da6..4f05d208c95c 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -26,11 +26,7 @@ Example: ti,pmic-shutdown-controller; regulators { - #address-cells = <1>; - #size-cells = <0>; - dcdc1_reg: dcdc1 { - reg = <0>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -38,7 +34,6 @@ Example: }; dcdc2_reg: dcdc2 { - reg = <1>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -46,7 +41,6 @@ Example: }; dcdc3_reg: dcc3 { - reg = <2>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; @@ -54,7 +48,6 @@ Example: }; ldo1_reg: ldo1 { - reg = <3>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -62,7 +55,6 @@ Example: }; ldo2_reg: ldo2 { - reg = <4>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -70,7 +62,6 @@ Example: }; ldo3_reg: ldo3 { - reg = <5>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -78,7 +69,6 @@ Example: }; ldo4_reg: ldo4 { - reg = <6>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt new file mode 100644 index 000000000000..76ebca568db9 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt @@ -0,0 +1,19 @@ +* Alphascale asm9260 SoC Real Time Clock + +Required properties: +- compatible: Should be "alphascale,asm9260-rtc" +- reg: Physical base address of the controller and length + of memory mapped region. +- interrupts: IRQ line for the RTC. +- clocks: Reference to the clock entry. +- clock-names: should contain: + * "ahb" for the SoC RTC clock + +Example: +rtc0: rtc@800a0000 { + compatible = "alphascale,asm9260-rtc"; + reg = <0x800a0000 0x100>; + clocks = <&acc CLKID_AHB_RTC>; + clock-names = "ahb"; + interrupts = <2>; +}; diff --git a/Documentation/devicetree/bindings/rtc/epson,rx6110.txt b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt new file mode 100644 index 000000000000..3dc313e01f77 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt @@ -0,0 +1,39 @@ +Epson RX6110 Real Time Clock +============================ + +The Epson RX6110 can be used with SPI or I2C busses. The kind of +bus depends on the SPISEL pin and can not be configured via software. + +I2C mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg : the I2C address of the device for I2C + +Example: + + rtc: rtc@32 { + compatible = "epson,rx6110" + reg = <0x32>; + }; + +SPI mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg: chip select number + - spi-cs-high: RX6110 needs chipselect high + - spi-cpha: RX6110 works with SPI shifted clock phase + - spi-cpol: RX6110 works with SPI inverse clock polarity + +Example: + + rtc: rtc@3 { + compatible = "epson,rx6110" + reg = <3> + spi-cs-high; + spi-cpha; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt new file mode 100644 index 000000000000..ddef330d2709 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -0,0 +1,37 @@ +* Maxim DS3231 Real Time Clock + +Required properties: +see: Documentation/devicetree/bindings/i2c/trivial-devices.txt + +Optional property: +- #clock-cells: Should be 1. +- clock-output-names: + overwrite the default clock names "ds3231_clk_sqw" and "ds3231_clk_32khz". + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: square-wave output on the SQW pin + - 1: square-wave output on the 32kHz pin + +- interrupts: rtc alarm/event interrupt. When this property is selected, + clock on the SQW pin cannot be used. + +Example: + +ds3231: ds3231@51 { + compatible = "maxim,ds3231"; + reg = <0x68>; + #clock-cells = <1>; +}; + +device1 { +... + clocks = <&ds3231 0>; +... +}; + +device2 { +... + clocks = <&ds3231 1>; +... +}; diff --git a/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt new file mode 100644 index 000000000000..180b7144bfcc --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt @@ -0,0 +1,21 @@ +* Microchip PIC32 Real Time Clock and Calendar + +The RTCC keeps time in hours, minutes, and seconds, and one half second. It +provides a calendar in weekday, date, month, and year. It also provides a +configurable alarm. + +Required properties: +- compatible: should be: "microchip,pic32mzda-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: RTC alarm/event interrupt +- clocks: clock phandle + +Example: + + rtc: rtc@1f8c0000 { + compatible = "microchip,pic32mzda-rtc"; + reg = <0x1f8c0000 0x60>; + interrupts = <166 IRQ_TYPE_EDGE_RISING>; + clocks = <&PBCLK6>; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index ac2fcd6ff4b8..1068ffce9f91 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -14,6 +14,10 @@ Required properties: interrupt number is the rtc alarm interrupt and second interrupt number is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. +- clocks: Must contain a list of phandle and clock specifier for the rtc + and source clocks. +- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the + same order as the clocks property. Example: @@ -21,4 +25,6 @@ Example: compatible = "samsung,s3c6410-rtc"; reg = <0x10070000 0x100>; interrupts = <44 0 45 0>; + clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index f67e761bcc18..bf2411f366e5 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -5,6 +5,7 @@ The HiSilicon SAS controller supports SAS/SATA. Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset + (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control @@ -13,7 +14,7 @@ Main node required properties: - ctrl-clock-ena-reg : offset to controller clock enable register in ctrl reg - queue-count : number of delivery and completion queues in the controller - phy-count : number of phys accessible by the controller - - interrupts : Interrupts for phys, completion queues, and fatal + - interrupts : For v1 hw: Interrupts for phys, completion queues, and fatal sources; the interrupts are ordered in 3 groups, as follows: - Phy interrupts - Completion queue interrupts @@ -30,6 +31,24 @@ Main node required properties: Fatal interrupts : the fatal interrupts are ordered as follows: - ECC - AXI bus + For v2 hw: Interrupts for phys, Sata, and completion queues; + the interrupts are ordered in 3 groups, as follows: + - Phy interrupts + - Sata interrupts + - Completion queue interrupts + Phy interrupts : Each controller has 2 phy interrupts: + - phy up/down + - channel interrupt + Sata interrupts : Each phy on the controller has 1 Sata + interrupt. The interrupts are ordered in increasing + order. + Completion queue interrupts : each completion queue has 1 + interrupt source. The interrupts are ordered in + increasing order. + +Optional main node properties: + - hip06-sas-v2-quirk-amt : when set, indicates that the v2 controller has the + "am-max-transmissions" limitation. Example: sas0: sas@c1000000 { diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 35ae1fb3537f..ed94c217c98d 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -9,7 +9,7 @@ Optional properties: - fsl,uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works - is DCE mode by default. + in DCE mode by default. Note: Each uart controller should have an alias correctly numbered in "aliases" node. diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index e2cd1d7539e5..6e699ceabacd 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -33,12 +33,19 @@ Optional properties: Note that this is not needed in case the clocks are stable throughout the entire runtime of the codec. + - vd-supply: Digital power + - vl-supply: Logic power + - va-supply: Analog Power + Examples: codec_i2c: cs4271@10 { compatible = "cirrus,cs4271"; reg = <0x10>; reset-gpio = <&gpio 23 0>; + vd-supply = <&vdd_3v3_reg>; + vl-supply = <&vdd_3v3_reg>; + va-supply = <&vdd_3v3_reg>; }; codec_spi: cs4271@0 { diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt index ce55c0a6f757..4da41bf1888e 100644 --- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -30,6 +30,8 @@ The compatible list for this generic sound card currently: "fsl,imx-audio-sgtl5000" (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt) + "fsl,imx-audio-wm8960" + Required properties: - compatible : Contains one of entries in the compatible list. diff --git a/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt new file mode 100644 index 000000000000..8a18d71e6879 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt @@ -0,0 +1,31 @@ +Analog Devices AXI SPI Engine controller Device Tree Bindings + +Required properties: +- compatible : Must be "adi,axi-spi-engine-1.00.a"" +- reg : Physical base address and size of the register map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names - "s_axi_aclk", "spi_clk" +- clocks : Clock phandles and specifiers (See clock bindings for + details on clock-names and clocks). +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional subnodes: + Subnodes are use to represent the SPI slave devices connected to the SPI + master. They follow the generic SPI bindings as outlined in spi-bus.txt. + +Example: + + spi@@44a00000 { + compatible = "adi,axi-spi-engine-1.00.a"; + reg = <0x44a00000 0x1000>; + interrupts = <0 56 4>; + clocks = <&clkc 15 &clkc 15>; + clock-names = "s_axi_aclk", "spi_clk"; + + #address-cells = <1>; + #size-cells = <0>; + + /* SPI devices */ + }; diff --git a/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt new file mode 100644 index 000000000000..852b651f3bc5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt @@ -0,0 +1,54 @@ +* ICP DAS LP-8841 SPI Controller for RTC + +ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO +memory register, which acts as an SPI master device. + +The device uses the standard MicroWire half-duplex transfer timing. +Master output is set on low clock and sensed by the RTC on the rising +edge. Master input is set by the RTC on the trailing edge and is sensed +by the master on low clock. + +Required properties: + +- #address-cells: should be 1 + +- #size-cells: should be 0 + +- compatible: should be "icpdas,lp8841-spi-rtc" + +- reg: should provide IO memory address + +Requirements to SPI slave nodes: + +- There can be only one slave device. + +- The spi slave node should claim the following flags which are + required by the spi controller. + + - spi-3wire: The master itself has only 3 wire. It cannor work in + full duplex mode. + + - spi-cs-high: DS-1302 has active high chip select line. The master + doesn't support active low. + + - spi-lsb-first: DS-1302 requires least significant bit first + transfers. The master only support this type of bit ordering. + + +Example: + +spi@901c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "icpdas,lp8841-spi-rtc"; + reg = <0x901c 0x1>; + + rtc@0 { + compatible = "maxim,ds1302"; + reg = <0>; + spi-max-frequency = <500000>; + spi-3wire; + spi-lsb-first; + spi-cs-high; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 0c491bda4c65..1b14d69d8903 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -9,6 +9,7 @@ Required Properties: "rockchip,rk3066-spi" for rk3066. "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. + "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt new file mode 100644 index 000000000000..c7b7856bd528 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -0,0 +1,22 @@ +Xilinx SPI controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b" +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller + +Optional properties: +- xlnx,num-ss-bits : Number of chip selects used. + +Example: + axi_quad_spi@41e00000 { + compatible = "xlnx,xps-spi-2.00.a"; + interrupt-parent = <&intc>; + interrupts = <0 31 1>; + reg = <0x41e00000 0x10000>; + xlnx,num-ss-bits = <0x1>; + }; + diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 332e625f6ed0..e5ee3f159893 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -1,8 +1,9 @@ * Renesas R-Car Thermal Required properties: -- compatible : "renesas,thermal-<soctype>", "renesas,rcar-thermal" - as fallback. +- compatible : "renesas,thermal-<soctype>", + "renesas,rcar-gen2-thermal" (with thermal-zone) or + "renesas,rcar-thermal" (without thermal-zone) as fallback. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) - "renesas,thermal-r8a7779" (R-Car H1) @@ -36,3 +37,35 @@ thermal@e61f0000 { 0xe61f0300 0x38>; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; }; + +Example (with thermal-zone): + +thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <1000>; + polling-delay = <5000>; + + thermal-sensors = <&thermal>; + + trips { + cpu-crit { + temperature = <115000>; + hysteresis = <0>; + type = "critical"; + }; + }; + cooling-maps { + }; + }; +}; + +thermal: thermal@e61f0000 { + compatible = "renesas,thermal-r8a7790", + "renesas,rcar-gen2-thermal", + "renesas,rcar-thermal"; + reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; + power-domains = <&cpg_clocks>; + #thermal-sensor-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index e00029d66d66..83700da22b79 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -120,6 +120,7 @@ intercontrol Inter Control Group invensense InvenSense Inc. isee ISEE 2007 S.L. isil Intersil +issi Integrated Silicon Solutions Inc. jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH @@ -205,6 +206,7 @@ seagate Seagate Technology PLC semtech Semtech Corporation sgx SGX Sensortech sharp Sharp Corporation +si-en Si-En Technology Ltd. sigma Sigma Designs, Inc. sil Silicon Image silabs Silicon Laboratories |