diff options
Diffstat (limited to 'Documentation/devicetree')
46 files changed, 1367 insertions, 64 deletions
diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt new file mode 100644 index 000000000000..4755caaccba6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -0,0 +1,8 @@ +Calxeda Highbank Platforms Device Tree Bindings +----------------------------------------------- + +Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,highbank"; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt new file mode 100644 index 000000000000..c9848ad0e2e3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -0,0 +1,26 @@ +Freescale i.MX Platforms Device Tree Bindings +----------------------------------------------- + +i.MX51 Babbage Board +Required root node properties: + - compatible = "fsl,imx51-babbage", "fsl,imx51"; + +i.MX53 Automotive Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-ard", "fsl,imx53"; + +i.MX53 Evaluation Kit +Required root node properties: + - compatible = "fsl,imx53-evk", "fsl,imx53"; + +i.MX53 Quick Start Board +Required root node properties: + - compatible = "fsl,imx53-qsb", "fsl,imx53"; + +i.MX53 Smart Mobile Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-smd", "fsl,imx53"; + +i.MX6 Quad SABRE Automotive Board +Required root node properties: + - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt new file mode 100644 index 000000000000..52916b4aa1fe --- /dev/null +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -0,0 +1,55 @@ +* ARM Generic Interrupt Controller + +ARM SMP cores are often associated with a GIC, providing per processor +interrupts (PPI), shared processor interrupts (SPI) and software +generated interrupts (SGI). + +Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. +Secondary GICs are cascaded into the upward interrupt controller and do not +have PPIs or SGIs. + +Main node required properties: + +- compatible : should be one of: + "arm,cortex-a9-gic" + "arm,arm11mp-gic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 3. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of + the 8 possible cpus attached to the GIC. A bit set to '1' indicated + the interrupt is wired to that CPU. Only valid for PPI interrupts. + +- reg : Specifies base physical address(s) and size of the GIC registers. The + first region is the GIC distributor register base and size. The 2nd region is + the GIC cpu interface register base and size. + +Optional +- interrupts : Interrupt source of the parent interrupt controller. Only + present on secondary GICs. + +Example: + + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt new file mode 100644 index 000000000000..7ca52161e7ab --- /dev/null +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -0,0 +1,44 @@ +* ARM L2 Cache Controller + +ARM cores often have a separate level 2 cache controller. There are various +implementations of the L2 cache controller with compatible programming models. +The ARM L2 cache representation in the device tree should be done as follows: + +Required properties: + +- compatible : should be one of: + "arm,pl310-cache" + "arm,l220-cache" + "arm,l210-cache" +- cache-unified : Specifies the cache is a unified cache. +- cache-level : Should be set to 2 for a level 2 cache. +- reg : Physical base address and size of cache controller's memory mapped + registers. + +Optional properties: + +- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of + read, write and setup latencies. Minimum valid values are 1. Controllers + without setup latency control should use a value of 0. +- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of + read, write and setup latencies. Controllers without setup latency control + should use 0. Controllers without separate read and write Tag RAM latency + values should only use the first cell. +- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell. +- arm,filter-ranges : <start length> Starting address and length of window to + filter. Addresses in the filter window are directed to the M1 port. Other + addresses will go to the M0 port. +- interrupts : 1 combined interrupt. + +Example: + +L2: cache-controller { + compatible = "arm,pl310-cache"; + reg = <0xfff12000 0x1000>; + arm,data-latency = <1 1 1>; + arm,tag-latency = <2 2 2>; + arm,filter-latency = <0x80000000 0x8000000>; + cache-unified; + cache-level = <2>; + interrupts = <45>; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/dsp.txt b/Documentation/devicetree/bindings/arm/omap/dsp.txt new file mode 100644 index 000000000000..d3830a32ce08 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/dsp.txt @@ -0,0 +1,14 @@ +* TI - DSP (Digital Signal Processor) + +TI DSP included in OMAP SoC + +Required properties: +- compatible : Should be "ti,omap3-c64" for OMAP3 & 4 +- ti,hwmods: "dsp" + +Examples: + +dsp { + compatible = "ti,omap3-c64"; + ti,hwmods = "dsp"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/iva.txt b/Documentation/devicetree/bindings/arm/omap/iva.txt new file mode 100644 index 000000000000..6d6295171358 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/iva.txt @@ -0,0 +1,19 @@ +* TI - IVA (Imaging and Video Accelerator) subsystem + +The IVA contain various audio, video or imaging HW accelerator +depending of the version. + +Required properties: +- compatible : Should be: + - "ti,ivahd" for OMAP4 + - "ti,iva2.2" for OMAP3 + - "ti,iva2.1" for OMAP2430 + - "ti,iva1" for OMAP2420 +- ti,hwmods: "iva" + +Examples: + +iva { + compatible = "ti,ivahd", "ti,iva"; + ti,hwmods = "iva"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt new file mode 100644 index 000000000000..6888a5efc860 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -0,0 +1,19 @@ +* TI - L3 Network On Chip (NoC) + +This version is an implementation of the generic NoC IP +provided by Arteris. + +Required properties: +- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family + Should be "ti,omap4-l3-noc" for OMAP4 family +- ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. + +Examples: + +ocp { + compatible = "ti,omap4-l3-noc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt new file mode 100644 index 000000000000..1a5a42ce21bb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -0,0 +1,27 @@ +* TI - MPU (Main Processor Unit) subsystem + +The MPU subsystem contain one or several ARM cores +depending of the version. +The MPU contain CPUs, GIC, L2 cache and a local PRCM. + +Required properties: +- compatible : Should be "ti,omap3-mpu" for OMAP3 + Should be "ti,omap4-mpu" for OMAP4 +- ti,hwmods: "mpu" + +Examples: + +- For an OMAP4 SMP system: + +mpu { + compatible = "ti,omap4-mpu"; + ti,hwmods = "mpu"; +}; + + +- For an OMAP3 monocore system: + +mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt new file mode 100644 index 000000000000..dbdab40ed3a6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -0,0 +1,43 @@ +* Texas Instruments OMAP + +OMAP is currently using a static file per SoC family to describe the +IPs present in the SoC. +On top of that an omap_device is created to extend the platform_device +capabilities and to allow binding with one or several hwmods. +The hwmods will contain all the information to build the device: +adresse range, irq lines, dma lines, interconnect, PRCM register, +clock domain, input clocks. +For the moment just point to the existing hwmod, the next step will be +to move data from hwmod to device-tree representation. + + +Required properties: +- compatible: Every devices present in OMAP SoC should be in the + form: "ti,XXX" +- ti,hwmods: list of hwmod names (ascii strings), that comes from the OMAP + HW documentation, attached to a device. Must contain at least + one hwmod. + +Optional properties: +- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module + during suspend. + + +Example: + +spinlock@1 { + compatible = "ti,omap4-spinlock"; + ti,hwmods = "spinlock"; +}; + + +Boards: + +- OMAP3 BeagleBoard : Low cost community board + compatible = "ti,omap3-beagle", "ti,omap3" + +- OMAP4 SDP : Software Developement Board + compatible = "ti,omap4-sdp", "ti,omap4430" + +- OMAP4 PandaBoard : Low cost community board + compatible = "ti,omap4-panda", "ti,omap4430" diff --git a/Documentation/devicetree/bindings/arm/picoxcell.txt b/Documentation/devicetree/bindings/arm/picoxcell.txt new file mode 100644 index 000000000000..e75c0ef51e69 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/picoxcell.txt @@ -0,0 +1,24 @@ +Picochip picoXcell device tree bindings. +======================================== + +Required root node properties: + - compatible: + - "picochip,pc7302-pc3x3" : PC7302 development board with PC3X3 device. + - "picochip,pc7302-pc3x2" : PC7302 development board with PC3X2 device. + - "picochip,pc3x3" : picoXcell PC3X3 device based board. + - "picochip,pc3x2" : picoXcell PC3X2 device based board. + +Timers required properties: + - compatible = "picochip,pc3x2-timer" + - interrupts : The single IRQ line for the timer. + - clock-freq : The frequency in HZ of the timer. + - reg : The register bank for the timer. + +Note: two timers are required - one for the scheduler clock and one for the +event tick/NOHZ. + +VIC required properties: + - compatible = "arm,pl192-vic". + - interrupt-controller. + - reg : The register bank for the device. + - #interrupt-cells : Must be 1. diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt index 1d5d7a870ec7..951ca46789d4 100644 --- a/Documentation/devicetree/bindings/arm/primecell.txt +++ b/Documentation/devicetree/bindings/arm/primecell.txt @@ -6,7 +6,9 @@ driver matching. Required properties: -- compatible : should be a specific value for peripheral and "arm,primecell" +- compatible : should be a specific name for the peripheral and + "arm,primecell". The specific name will match the ARM + engineering name for the logic block in the form: "arm,pl???" Optional properties: diff --git a/Documentation/devicetree/bindings/ata/calxeda-sata.txt b/Documentation/devicetree/bindings/ata/calxeda-sata.txt new file mode 100644 index 000000000000..79caa5651f53 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/calxeda-sata.txt @@ -0,0 +1,17 @@ +* Calxeda SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, contains "calxeda,hb-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> + +Example: + sata@ffe08000 { + compatible = "calxeda,hb-ahci"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; + diff --git a/Documentation/devicetree/bindings/crypto/picochip-spacc.txt b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt new file mode 100644 index 000000000000..d8609ece1f4c --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt @@ -0,0 +1,23 @@ +Picochip picoXcell SPAcc (Security Protocol Accelerator) bindings + +Picochip picoXcell devices contain crypto offload engines that may be used for +IPSEC and femtocell layer 2 ciphering. + +Required properties: + - compatible : "picochip,spacc-ipsec" for the IPSEC offload engine + "picochip,spacc-l2" for the femtocell layer 2 ciphering engine. + - reg : Offset and length of the register set for this device + - interrupt-parent : The interrupt controller that controls the SPAcc + interrupt. + - interrupts : The interrupt line from the SPAcc. + - ref-clock : The input clock that drives the SPAcc. + +Example SPAcc node: + +spacc@10000 { + compatible = "picochip,spacc-ipsec"; + reg = <0x100000 0x10000>; + interrupt-parent = <&vic0>; + interrupts = <24>; + ref-clock = <&ipsec_clk>, "ref"; +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 064db928c3c1..141087cf3107 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -8,7 +8,7 @@ node's name represents the name of the corresponding LED. LED sub-node properties: - gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/powerpc/booting-without-of.txt. Active + for devices" in Documentation/devicetree/booting-without-of.txt. Active low LEDs should be indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt new file mode 100644 index 000000000000..a2c416bcbccc --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt @@ -0,0 +1,10 @@ +ARM PL061 GPIO controller + +Required properties: +- compatible : "arm,pl061", "arm,primecell" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt mapping for GPIO IRQ. + diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt new file mode 100644 index 000000000000..f3cf43b66f7e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt @@ -0,0 +1,25 @@ +* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX + +Required properties: +- compatible : Should be "fsl,<chip>-i2c" +- reg : Should contain I2C/HS-I2C registers location and length +- interrupts : Should contain I2C/HS-I2C interrupt + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples: + +i2c@83fc4000 { /* I2C2 on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; +}; + +i2c@70038000 { /* HS-I2C on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x70038000 0x4000>; + interrupts = <64>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt new file mode 100644 index 000000000000..38832c712919 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt @@ -0,0 +1,39 @@ +* Samsung's I2C controller + +The Samsung's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. + (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. + +Optional properties: + - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not + specified, default value is 0. + - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not + specified, the default value in Hz is 100000. + +Example: + + i2c@13870000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x13870000 0x100>; + interrupts = <345>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <100000>; + gpios = <&gpd1 2 0 /* SDA */ + &gpd1 3 0 /* SCL */>; + #address-cells = <1>; + #size-cells = <0>; + + wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt new file mode 100644 index 000000000000..7e51154679a6 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt @@ -0,0 +1,27 @@ +* NVIDIA Tegra Secure Digital Host Controller + +This controller on Tegra family SoCs provides an interface for MMC, SD, +and SDIO types of memory cards. + +Required properties: +- compatible : Should be "nvidia,<chip>-sdhci" +- reg : Should contain SD/MMC registers location and length +- interrupts : Should contain SD/MMC interrupt + +Optional properties: +- cd-gpios : Specify GPIOs for card detection +- wp-gpios : Specify GPIOs for write protection +- power-gpios : Specify GPIOs for power control +- support-8bit : Boolean, indicates if 8-bit mode should be used. + +Example: + +sdhci@c8000200 { + compatible = "nvidia,tegra20-sdhci"; + reg = <0xc8000200 0x200>; + interrupts = <47>; + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 155 0>; /* gpio PT3 */ + support-8bit; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt new file mode 100644 index 000000000000..ef66ddd01da0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt @@ -0,0 +1,14 @@ +* Atmel Data Flash + +Required properties: +- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash". + +Example: + +flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <25000000>; + reg = <1>; +}; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index 1a729f089866..1ad80d5865a9 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -1,61 +1,24 @@ -CAN Device Tree Bindings ------------------------- -2011 Freescale Semiconductor, Inc. +Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC). -fsl,flexcan-v1.0 nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source shall be used for the controller. +Required properties: -CPI Clock- Can Protocol Interface Clock - This CLK_SRC bit of CTRL(control register) selects the clock source to - the CAN Protocol Interface(CPI) to be either the peripheral clock - (driven by the PLL) or the crystal oscillator clock. The selected clock - is the one fed to the prescaler to generate the Serial Clock (Sclock). - The PRESDIV field of CTRL(control register) controls a prescaler that - generates the Serial Clock (Sclock), whose period defines the - time quantum used to compose the CAN waveform. +- compatible : Should be "fsl,<processor>-flexcan" -Can Engine Clock Source - There are two sources for CAN clock - - Platform Clock It represents the bus clock - - Oscillator Clock + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: - Peripheral Clock (PLL) - -------------- - | - --------- ------------- - | |CPI Clock | Prescaler | Sclock - | |---------------->| (1.. 256) |------------> - --------- ------------- - | | - -------------- ---------------------CLK_SRC - Oscillator Clock + - fsl,p1010-flexcan -- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects - the peripheral clock. PLL clock is fed to the - prescaler to generate the Serial Clock (Sclock). - Valid values are "oscillator" and "platform" - "oscillator": CAN engine clock source is oscillator clock. - "platform" The CAN engine clock source is the bus clock - (platform clock). +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device +- clock-frequency : The oscillator frequency driving the flexcan device -- fsl,flexcan-clock-divider : for the reference and system clock, an additional - clock divider can be specified. -- clock-frequency: frequency required to calculate the bitrate for FlexCAN. +Example: -Note: - - v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC. - - P1010 does not have oscillator as the Clock Source.So the default - Clock Source is platform clock. -Examples: - - can0@1c000 { - compatible = "fsl,flexcan-v1.0"; + can@1c000 { + compatible = "fsl,p1010-flexcan"; reg = <0x1c000 0x1000>; interrupts = <48 0x2>; interrupt-parent = <&mpic>; - fsl,flexcan-clock-source = "platform"; - fsl,flexcan-clock-divider = <2>; - clock-frequency = <fixed by u-boot>; + clock-frequency = <200000000>; // filled in by bootloader }; diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt new file mode 100644 index 000000000000..adb5b5744ecd --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -0,0 +1,38 @@ +* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller + +Required properties: +- compatible : Should be "smsc,lan<model>", "smsc,lan9115" +- reg : Address and length of the io space for SMSC LAN +- interrupts : Should contain SMSC LAN interrupt line +- interrupt-parent : Should be the phandle for the interrupt controller + that services interrupts for this device +- phy-mode : String, operation mode of the PHY interface. + Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", + "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". + +Optional properties: +- reg-shift : Specify the quantity to shift the register offsets by +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value for SMSC LAN is + 2 or 4. If it's omitted or invalid, the size would be 2. +- smsc,irq-active-high : Indicates the IRQ polarity is active-high +- smsc,irq-push-pull : Indicates the IRQ type is push-pull +- smsc,force-internal-phy : Forces SMSC LAN controller to use + internal PHY +- smsc,force-external-phy : Forces SMSC LAN controller to use + external PHY +- smsc,save-mac-address : Indicates that mac address needs to be saved + before resetting the controller +- local-mac-address : 6 bytes, mac address + +Examples: + +lan9220@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>; + reg-io-width = <4>; + smsc,irq-push-pull; +}; diff --git a/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt b/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt new file mode 100644 index 000000000000..36f82dbdd14d --- /dev/null +++ b/Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt @@ -0,0 +1,5 @@ +NVIDIA Tegra 2 pinmux controller + +Required properties: +- compatible : "nvidia,tegra20-pinmux" + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt index 39e941515a36..380914e965e0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -1,3 +1,8 @@ +Freescale Reference Board Bindings + +This document describes device tree bindings for various devices that +exist on some Freescale reference boards. + * Board Control and Status (BCSR) Required properties: @@ -12,25 +17,26 @@ Example: reg = <f8000000 8000>; }; -* Freescale on board FPGA +* Freescale on-board FPGA This is the memory-mapped registers for on board FPGA. Required properities: -- compatible : should be "fsl,fpga-pixis". -- reg : should contain the address and the length of the FPPGA register - set. +- compatible: should be a board-specific string followed by a string + indicating the type of FPGA. Example: + "fsl,<board>-fpga", "fsl,fpga-pixis" +- reg: should contain the address and the length of the FPGA register set. - interrupt-parent: should specify phandle for the interrupt controller. -- interrupts : should specify event (wakeup) IRQ. +- interrupts: should specify event (wakeup) IRQ. -Example (MPC8610HPCD): +Example (P1022DS): - board-control@e8000000 { - compatible = "fsl,fpga-pixis"; - reg = <0xe8000000 32>; - interrupt-parent = <&mpic>; - interrupts = <8 8>; - }; + board-control@3,0 { + compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + interrupt-parent = <&mpic>; + interrupts = <8 8 0 0>; + }; * Freescale BCSR GPIO banks diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt new file mode 100644 index 000000000000..9d54eb5a295f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt @@ -0,0 +1,395 @@ +=================================================================== +Debug Control and Status Register (DCSR) Binding +Copyright 2011 Freescale Semiconductor Inc. + +NOTE: The bindings described in this document are preliminary and subject +to change. Some of the compatible strings that contain only generic names +may turn out to be inappropriate, or need additional properties to describe +the integration of the block with the rest of the chip. + +===================================================================== +Debug Control and Status Register Memory Map + +Description + +This node defines the base address and range for the +defined DCSR Memory Map. Child nodes will describe the individual +debug blocks defined within this memory space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr" and "simple-bus". + The DCSR space exists in the memory-mapped bus. + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing physical addresses in child nodes. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Defines the number of cells + or representing the size of physical addresses in + child nodes. + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + range of the DCSR space. + +EXAMPLE + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + +===================================================================== +Event Processing Unit + +This node represents the region of DCSR space allocated to the EPU + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-epu" + + - interrupts + Usage: required + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by the EPU. + The value of the interrupts property consists of three + interrupt specifiers. The format of the specifier is defined + by the binding document describing the node's interrupt parent. + + The EPU counters can be configured to assert the performance + monitor interrupt signal based on either counter overflow or value + match. Which counter asserted the interrupt is captured in an EPU + Counter Interrupt Status Register (EPCPUISR). + + The EPU unit can also be configured to assert either or both of + two interrupt signals based on debug event sources within the SoC. + The interrupt signals are epu_xt_int0 and epu_xt_int1. + Which event source asserted the interrupt is captured in an EPU + Interrupt Status Register (EPISR0,EPISR1). + + Interrupt numbers are lised in order (perfmon, event0, event1). + + - interrupt-parent + Usage: required + Value type: <phandle> + Definition: A single <phandle> value that points + to the interrupt parent to which the child domain + is being mapped. Value must be "&mpic" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + +======================================================================= +Nexus Port Controller + +This node represents the region of DCSR space allocated to the NPC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-npc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The Nexus Port controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the Nexus Port Controller + control and status registers. + + The second register range describes the Nexus Port Controller + internal trace buffer. The NPC trace buffer is a small memory buffer + which stages the nexus trace data for transmission via the Aurora port + or to a DDR based trace buffer. In some configurations the NPC trace + buffer can be the only trace buffer used. + + +EXAMPLE + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + +======================================================================= +Nexus Concentrator + +This node represents the region of DCSR space allocated to the NXC + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-nxc" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; +======================================================================= +CoreNet Debug Controller + +This node represents the region of DCSR space allocated to +the CoreNet Debug controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-corenet" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + The CoreNet Debug controller occupies two regions in the DCSR space + with distinct functionality. + + The first register range describes the CoreNet Debug Controller + functionalty to perform transaction and transaction attribute matches. + + The second register range describes the CoreNet Debug Controller + functionalty to trigger event notifications and debug traces. + +EXAMPLE + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + +======================================================================= +Data Path Debug controller + +This node represents the region of DCSR space allocated to +the DPAA Debug Controller. This controller controls debug configuration +for the QMAN and FMAN blocks. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-dpaa" in addition to the + generic compatible string "fsl,dcsr-dpaa". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-dpaa@9000 { + compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + +======================================================================= +OCeaN Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-ocn" in addition to the + generic compatible string "fsl,dcsr-ocn". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ocn@11000 { + compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + +======================================================================= +DDR Controller Debug controller + +This node represents the region of DCSR space allocated to +the OCN Debug Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,dcsr-ddr" + + - dev-handle + Usage: required + Definition: A phandle to associate this debug node with its + component controller. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr1>; + reg = <0x12000 0x1000>; + }; + +======================================================================= +Nexus Aurora Link Controller + +This node represents the region of DCSR space allocated to +the NAL Controller. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-nal" in addition to the + generic compatible string "fsl,dcsr-nal". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-nal@18000 { + compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + + +======================================================================= +Run Control and Power Management + +This node represents the region of DCSR space allocated to +the RCPM Debug Controller. This functionlity is limited to the +control the debug operations of the SoC and cores. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the SoC + or Debug IP of the form "fsl,<soc>-dcsr-rcpm" in addition to the + generic compatible string "fsl,dcsr-rcpm". + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-rcpm@22000 { + compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + +======================================================================= +Core Service Bridge Proxy + +This node represents the region of DCSR space allocated to +the Core Service Bridge Proxies. +There is one Core Service Bridge Proxy device for each CPU in the system. +This functionlity provides access to the debug operations of the CPU. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include both an identifier specific to the cpu + of the form "fsl,dcsr-<cpu>-sb-proxy" in addition to the + generic compatible string "fsl,dcsr-cpu-sb-proxy". + + - cpu-handle + Usage: required + Definition: A phandle to associate this debug node with its cpu. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical address + offset and length of the DCSR space registers of the device + configuration block. + +EXAMPLE + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", + "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + +======================================================================= diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt index 70558c3f3682..5d586e1ccaf5 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -25,6 +25,16 @@ Required properties: are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed to MPIC. +Optional properties: +- msi-address-64: 64-bit PCI address of the MSIIR register. The MSIIR register + is used for MSI messaging. The address of MSIIR in PCI address space is + the MSI message address. + + This property may be used in virtualized environments where the hypervisor + has created an alternate mapping for the MSIR block. See below for an + explanation. + + Example: msi@41600 { compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; @@ -41,3 +51,35 @@ Example: 0xe7 0>; interrupt-parent = <&mpic>; }; + +The Freescale hypervisor and msi-address-64 +------------------------------------------- +Normally, PCI devices have access to all of CCSR via an ATMU mapping. The +Freescale MSI driver calculates the address of MSIIR (in the MSI register +block) and sets that address as the MSI message address. + +In a virtualized environment, the hypervisor may need to create an IOMMU +mapping for MSIIR. The Freescale ePAPR hypervisor has this requirement +because of hardware limitations of the Peripheral Access Management Unit +(PAMU), which is currently the only IOMMU that the hypervisor supports. +The ATMU is programmed with the guest physical address, and the PAMU +intercepts transactions and reroutes them to the true physical address. + +In the PAMU, each PCI controller is given only one primary window. The +PAMU restricts DMA operations so that they can only occur within a window. +Because PCI devices must be able to DMA to memory, the primary window must +be used to cover all of the guest's memory space. + +PAMU primary windows can be divided into 256 subwindows, and each +subwindow can have its own address mapping ("guest physical" to "true +physical"). However, each subwindow has to have the same alignment, which +means they cannot be located at just any address. Because of these +restrictions, it is usually impossible to create a 4KB subwindow that +covers MSIIR where it's normally located. + +Therefore, the hypervisor has to create a subwindow inside the same +primary window used for memory, but mapped to the MSIR block (where MSIIR +lives). The first subwindow after the end of guest memory is used for +this. The address specified in the msi-address-64 property is the PCI +address of MSIIR. The hypervisor configures the PAMU to map that address to +the true physical address of MSIIR. diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt new file mode 100644 index 000000000000..1e753c69fc83 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -0,0 +1,31 @@ +* RS485 serial communications + +The RTS signal is capable of automatically controlling line direction for +the built-in half-duplex mode. +The properties described hereafter shall be given to a half-duplex capable +UART node. + +Required properties: +- rs485-rts-delay: prop-encoded-array <a b> where: + * a is the delay beteween rts signal and beginning of data sent in milliseconds. + it corresponds to the delay before sending data. + * b is the delay between end of data sent and rts signal in milliseconds + it corresponds to the delay after sending data and actual release of the line. + +Optional properties: +- linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 + feature at boot time. It can be disabled later with proper ioctl. +- rs485-rx-during-tx: empty property that enables the receiving of data even + whilst sending data. + +RS485 example for Atmel USART: + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 200>; // in milliseconds + }; + diff --git a/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt b/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt new file mode 100644 index 000000000000..2c3cd413f042 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt @@ -0,0 +1,11 @@ +* Freescale SGTL5000 Stereo Codec + +Required properties: +- compatible : "fsl,sgtl5000". + +Example: + +codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8510.txt b/Documentation/devicetree/bindings/sound/wm8510.txt new file mode 100644 index 000000000000..fa1a32b85577 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8510.txt @@ -0,0 +1,18 @@ +WM8510 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8510" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8510@1a { + compatible = "wlf,wm8510"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8523.txt b/Documentation/devicetree/bindings/sound/wm8523.txt new file mode 100644 index 000000000000..04746186b283 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8523.txt @@ -0,0 +1,16 @@ +WM8523 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8523" + + - reg : the I2C address of the device. + +Example: + +codec: wm8523@1a { + compatible = "wlf,wm8523"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt new file mode 100644 index 000000000000..7d9821f348da --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -0,0 +1,16 @@ +WM8580 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8580" + + - reg : the I2C address of the device. + +Example: + +codec: wm8580@1a { + compatible = "wlf,wm8580"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8711.txt b/Documentation/devicetree/bindings/sound/wm8711.txt new file mode 100644 index 000000000000..8ed9998cd23c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8711.txt @@ -0,0 +1,18 @@ +WM8711 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8711" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8711@1a { + compatible = "wlf,wm8711"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8728.txt b/Documentation/devicetree/bindings/sound/wm8728.txt new file mode 100644 index 000000000000..a8b5c3668e60 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8728.txt @@ -0,0 +1,18 @@ +WM8728 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8728" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8728@1a { + compatible = "wlf,wm8728"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8731.txt b/Documentation/devicetree/bindings/sound/wm8731.txt new file mode 100644 index 000000000000..15f70048469b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8731.txt @@ -0,0 +1,18 @@ +WM8731 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8731" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8731@1a { + compatible = "wlf,wm8731"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8737.txt b/Documentation/devicetree/bindings/sound/wm8737.txt new file mode 100644 index 000000000000..4bc2cea3b140 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8737.txt @@ -0,0 +1,18 @@ +WM8737 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8737" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8737@1a { + compatible = "wlf,wm8737"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8741.txt b/Documentation/devicetree/bindings/sound/wm8741.txt new file mode 100644 index 000000000000..74bda58c1bcf --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8741.txt @@ -0,0 +1,18 @@ +WM8741 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8741" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8741@1a { + compatible = "wlf,wm8741"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8750.txt b/Documentation/devicetree/bindings/sound/wm8750.txt new file mode 100644 index 000000000000..8db239fd5ecd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8750.txt @@ -0,0 +1,18 @@ +WM8750 and WM8987 audio CODECs + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8750" or "wlf,wm8987" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8750@1a { + compatible = "wlf,wm8750"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8753.txt b/Documentation/devicetree/bindings/sound/wm8753.txt new file mode 100644 index 000000000000..e65277a0fb60 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8753.txt @@ -0,0 +1,18 @@ +WM8753 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8753" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8737@1a { + compatible = "wlf,wm8753"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8770.txt b/Documentation/devicetree/bindings/sound/wm8770.txt new file mode 100644 index 000000000000..866e00ca150b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8770.txt @@ -0,0 +1,16 @@ +WM8770 audio CODEC + +This device supports SPI. + +Required properties: + + - compatible : "wlf,wm8770" + + - reg : the chip select number. + +Example: + +codec: wm8770@1 { + compatible = "wlf,wm8770"; + reg = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8776.txt b/Documentation/devicetree/bindings/sound/wm8776.txt new file mode 100644 index 000000000000..3b9ca49abc2b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8776.txt @@ -0,0 +1,18 @@ +WM8776 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8776" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8776@1a { + compatible = "wlf,wm8776"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt new file mode 100644 index 000000000000..4d3a56f38adc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -0,0 +1,18 @@ +WM8804 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm8804" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8804@1a { + compatible = "wlf,wm8804"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt new file mode 100644 index 000000000000..306ec3ff3c0e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -0,0 +1,12 @@ +ARM PL022 SPI controller + +Required properties: +- compatible : "arm,pl022", "arm,primecell" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt + +Optional properties: +- cs-gpios : should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + diff --git a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt new file mode 100644 index 000000000000..a49d9a1d4ccf --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt @@ -0,0 +1,27 @@ +* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +Required properties: +- compatible: Should be "atmel,<chip>-usart" + The compatible <chip> indicated will be the first SoC to support an + additional mode or an USART new feature. +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Optional properties: +- atmel,use-dma-rx: use of PDC or DMA for receiving data +- atmel,use-dma-tx: use of PDC or DMA for transmitting data + +<chip> compatible description: +- at91rm9200: legacy USART support +- at91sam9260: generic USART implementation for SAM9 SoCs + +Example: + + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + }; + diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt new file mode 100644 index 000000000000..aef383eb8876 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt @@ -0,0 +1,27 @@ +* Qualcomm MSM UART + +Required properties: +- compatible : + - "qcom,msm-uart", and one of "qcom,msm-hsuart" or + "qcom,msm-lsuart". +- reg : offset and length of the register set for the device + for the hsuart operating in compatible mode, there should be a + second pair describing the gsbi registers. +- interrupts : should contain the uart interrupt. + +There are two different UART blocks used in MSM devices, +"qcom,msm-hsuart" and "qcom,msm-lsuart". The msm-serial driver is +able to handle both of these, and matches against the "qcom,msm-uart" +as the compatibility. + +The registers for the "qcom,msm-hsuart" device need to specify both +register blocks, even for the common driver. + +Example: + + uart@19c400000 { + compatible = "qcom,msm-hsuart", "qcom,msm-uart"; + reg = <0x19c40000 0x1000>, + <0x19c00000 0x1000>; + interrupts = <195>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt new file mode 100644 index 000000000000..f13f1c5be91c --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt @@ -0,0 +1,25 @@ +* Synopsys DesignWare ABP UART + +Required properties: +- compatible : "snps,dw-apb-uart" +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART. + +Optional properties: +- reg-shift : quantity to shift the register offsets by. If this property is + not present then the register offsets are not shifted. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. If this property is not present then single byte + accesses are used. + +Example: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt new file mode 100644 index 000000000000..e8552782b440 --- /dev/null +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -0,0 +1,40 @@ +Device tree binding vendor prefix registry. Keep list in alphabetical order. + +This isn't an exhaustive list, but you should add new prefixes to it before +using them to avoid name-space collisions. + +adi Analog Devices, Inc. +amcc Applied Micro Circuits Corporation (APM, formally AMCC) +apm Applied Micro Circuits Corporation (APM) +arm ARM Ltd. +atmel Atmel Corporation +chrp Common Hardware Reference Platform +dallas Maxim Integrated Products (formerly Dallas Semiconductor) +denx Denx Software Engineering +epson Seiko Epson Corp. +est ESTeem Wireless Modems +fsl Freescale Semiconductor +GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. +gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +hp Hewlett Packard +ibm International Business Machines (IBM) +idt Integrated Device Technologies, Inc. +intercontrol Inter Control Group +linux Linux-specific binding +marvell Marvell Technology Group Ltd. +maxim Maxim Integrated Products +mosaixtech Mosaix Technologies, Inc. +national National Semiconductor +nintendo Nintendo +nvidia NVIDIA +nxp NXP Semiconductors +powervr Imagination Technologies +qcom Qualcomm, Inc. +ramtron Ramtron International +samsung Samsung Semiconductor +schindler Schindler +simtek +sirf SiRF Technology, Inc. +stericsson ST-Ericsson +ti Texas Instruments +xlnx Xilinx diff --git a/Documentation/devicetree/bindings/virtio/mmio.txt b/Documentation/devicetree/bindings/virtio/mmio.txt new file mode 100644 index 000000000000..5069c1b8e193 --- /dev/null +++ b/Documentation/devicetree/bindings/virtio/mmio.txt @@ -0,0 +1,17 @@ +* virtio memory mapped device + +See http://ozlabs.org/~rusty/virtio-spec/ for more details. + +Required properties: + +- compatible: "virtio,mmio" compatibility string +- reg: control registers base address and size including configuration space +- interrupts: interrupt generated by the device + +Example: + + virtio_block@3000 { + compatible = "virtio,mmio"; + reg = <0x3000 0x100>; + interrupts = <41>; + } |