diff options
Diffstat (limited to 'Documentation/devicetree')
11 files changed, 202 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/clock/exynos7-clock.txt b/Documentation/devicetree/bindings/clock/exynos7-clock.txt index 6d3d5f80c1c3..6bf1e7493f61 100644 --- a/Documentation/devicetree/bindings/clock/exynos7-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos7-clock.txt @@ -34,6 +34,8 @@ Required Properties for Clock Controller: - "samsung,exynos7-clock-peris" - "samsung,exynos7-clock-fsys0" - "samsung,exynos7-clock-fsys1" + - "samsung,exynos7-clock-mscl" + - "samsung,exynos7-clock-aud" - reg: physical base address of the controller and the length of memory mapped region. @@ -53,6 +55,7 @@ Input clocks for top0 clock controller: - dout_sclk_bus1_pll - dout_sclk_cc_pll - dout_sclk_mfc_pll + - dout_sclk_aud_pll Input clocks for top1 clock controller: - fin_pll @@ -76,6 +79,14 @@ Input clocks for peric1 clock controller: - sclk_uart1 - sclk_uart2 - sclk_uart3 + - sclk_spi0 + - sclk_spi1 + - sclk_spi2 + - sclk_spi3 + - sclk_spi4 + - sclk_i2s1 + - sclk_pcm1 + - sclk_spdif Input clocks for peris clock controller: - fin_pll @@ -91,3 +102,7 @@ Input clocks for fsys1 clock controller: - dout_aclk_fsys1_200 - dout_sclk_mmc0 - dout_sclk_mmc1 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt index ded5d6212c84..c6620bc96703 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt @@ -1,4 +1,4 @@ -NVIDIA Tegra124 Clock And Reset Controller +NVIDIA Tegra124 and Tegra132 Clock And Reset Controller This binding uses the common clock binding: Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -7,14 +7,16 @@ The CAR (Clock And Reset) Controller on Tegra is the HW module responsible for muxing and gating Tegra's clocks, and setting their rates. Required properties : -- compatible : Should be "nvidia,tegra124-car" +- compatible : Should be "nvidia,tegra124-car" or "nvidia,tegra132-car" - reg : Should contain CAR registers location and length - clocks : Should contain phandle and clock specifiers for two clocks: the 32 KHz "32k_in", and the board-specific oscillator "osc". - #clock-cells : Should be 1. In clock consumers, this cell represents the clock ID exposed by the - CAR. The assignments may be found in header file - <dt-bindings/clock/tegra124-car.h>. + CAR. The assignments may be found in the header files + <dt-bindings/clock/tegra124-car-common.h> (which covers IDs common + to Tegra124 and Tegra132) and <dt-bindings/clock/tegra124-car.h> + (for Tegra124-specific clocks). - #reset-cells : Should be 1. In clock consumers, this cell represents the bit number in the CAR's array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. diff --git a/Documentation/devicetree/bindings/clock/qcom,lcc.txt b/Documentation/devicetree/bindings/clock/qcom,lcc.txt new file mode 100644 index 000000000000..dd755be63a01 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,lcc.txt @@ -0,0 +1,21 @@ +Qualcomm LPASS Clock & Reset Controller Binding +------------------------------------------------ + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,lcc-msm8960" + "qcom,lcc-apq8064" + "qcom,lcc-ipq8064" + +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 +- #reset-cells : shall contain 1 + +Example: + clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 266ff9d23229..df4a259a6898 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -1,6 +1,6 @@ -* Clock Block on Freescale CoreNet Platforms +* Clock Block on Freescale QorIQ Platforms -Freescale CoreNet chips take primary clocking input from the external +Freescale qoriq chips take primary clocking input from the external SYSCLK signal. The SYSCLK input (frequency) is multiplied using multiple phase locked loops (PLL) to create a variety of frequencies which can then be passed to a variety of internal logic, including @@ -29,6 +29,7 @@ Required properties: * "fsl,t4240-clockgen" * "fsl,b4420-clockgen" * "fsl,b4860-clockgen" + * "fsl,ls1021a-clockgen" Chassis clock strings include: * "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks * "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 2e18676bd4b5..0a80fa70ca26 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -11,6 +11,7 @@ Required Properties: - compatible: Must be one of the following - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks + - "renesas,r8a73a4-mstp-clocks" for R8A73A4 (R-Mobile APE6) MSTP gate clocks - "renesas,r8a7740-mstp-clocks" for R8A7740 (R-Mobile A1) MSTP gate clocks - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt new file mode 100644 index 000000000000..ece92393e80d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt @@ -0,0 +1,33 @@ +* Renesas R8A73A4 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A73A4 SoC. It includes five PLLs +and several fixed ratio dividers. + +Required Properties: + + - compatible: Must be "renesas,r8a73a4-cpg-clocks" + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the parent clocks ("extal1" and "extal2") + + - #clock-cells: Must be 1 + + - clock-output-names: The names of the clocks. Supported clocks are "main", + "pll0", "pll1", "pll2", "pll2s", "pll2h", "z", "z2", "i", "m3", "b", + "m1", "m2", "zx", "zs", and "hp". + + +Example +------- + + cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a73a4-cpg-clocks"; + reg = <0 0xe6150000 0 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>; + #clock-cells = <1>; + clock-output-names = "main", "pll0", "pll1", "pll2", + "pll2s", "pll2h", "z", "z2", + "i", "m3", "b", "m1", "m2", + "zx", "zs", "hp"; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index e6ad35b894f9..b02944fba9de 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -8,15 +8,18 @@ Required Properties: - compatible: Must be one of - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG - "renesas,rcar-gen2-cpg-clocks" for the generic R-Car Gen2 CPG - reg: Base address and length of the memory resource used by the CPG - - clocks: Reference to the parent clock + - clocks: References to the parent clocks: first to the EXTAL clock, second + to the USB_EXTAL clock - #clock-cells: Must be 1 - clock-output-names: The names of the clocks. Supported clocks are "main", - "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1" and "z" + "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", and + "adsp" Example @@ -26,8 +29,9 @@ Example compatible = "renesas,r8a7790-cpg-clocks", "renesas,rcar-gen2-cpg-clocks"; reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk>; + clocks = <&extal_clk &usb_extal_clk>; #clock-cells = <1>; clock-output-names = "main", "pll0, "pll1", "pll3", - "lb", "qspi", "sdh", "sd0", "sd1", "z"; + "lb", "qspi", "sdh", "sd0", "sd1", "z", + "rcan", "adsp"; }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 67b2b99f2b33..60b44285250d 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -26,7 +26,7 @@ Required properties: "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 - "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 + "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80 @@ -55,9 +55,11 @@ Required properties: "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 - "allwinner,sun4i-a10-mmc-output-clk" - for the MMC output clock on A10 - "allwinner,sun4i-a10-mmc-sample-clk" - for the MMC sample clock on A10 + "allwinner,sun4i-a10-mmc-clk" - for the MMC clock + "allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80 + "allwinner,sun9i-a80-mmc-config-clk" - for mmc gates + resets on A80 "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks + "allwinner,sun9i-a80-mod0-clk" - for module 0 (storage) clocks on A80 "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 @@ -73,7 +75,9 @@ Required properties for all clocks: - #clock-cells : from common clock binding; shall be set to 0 except for the following compatibles where it shall be set to 1: "allwinner,*-gates-clk", "allwinner,sun4i-pll5-clk", - "allwinner,sun4i-pll6-clk", "allwinner,sun6i-a31-pll6-clk" + "allwinner,sun4i-pll6-clk", "allwinner,sun6i-a31-pll6-clk", + "allwinner,*-usb-clk", "allwinner,*-mmc-clk", + "allwinner,*-mmc-config-clk" - clock-output-names : shall be the corresponding names of the outputs. If the clock module only has one output, the name shall be the module name. @@ -81,6 +85,10 @@ Required properties for all clocks: And "allwinner,*-usb-clk" clocks also require: - reset-cells : shall be set to 1 +The "allwinner,sun9i-a80-mmc-config-clk" clock also requires: +- #reset-cells : shall be set to 1 +- resets : shall be the reset control phandle for the mmc block. + For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate dummy clocks at 25 MHz and 125 MHz, respectively. See example. @@ -95,6 +103,14 @@ For "allwinner,sun6i-a31-pll6-clk", there are 2 outputs. The first output is the normal PLL6 output, or "pll6". The second output is rate doubled PLL6, or "pll6x2". +The "allwinner,*-mmc-clk" clocks have three different outputs: the +main clock, with the ID 0, and the output and sample clocks, with the +IDs 1 and 2, respectively. + +The "allwinner,sun9i-a80-mmc-config-clk" clock has one clock/reset output +per mmc controller. The number of outputs is determined by the size of +the address block, which is related to the overall mmc block. + For example: osc24M: clk@01c20050 { @@ -138,11 +154,11 @@ cpu: cpu@01c20054 { }; mmc0_clk: clk@01c20088 { - #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-mmc-clk"; reg = <0x01c20088 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; - clock-output-names = "mmc0"; + clock-output-names = "mmc0", "mmc0_output", "mmc0_sample"; }; mii_phy_tx_clk: clk@2 { @@ -170,3 +186,16 @@ gmac_clk: clk@01c20164 { clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; clock-output-names = "gmac"; }; + +mmc_config_clk: clk@01c13000 { + compatible = "allwinner,sun9i-a80-mmc-config-clk"; + reg = <0x01c13000 0x10>; + clocks = <&ahb0_gates 8>; + clock-names = "ahb"; + resets = <&ahb0_resets 8>; + reset-names = "ahb"; + #clock-cells = <1>; + #reset-cells = <1>; + clock-output-names = "mmc0_config", "mmc1_config", + "mmc2_config", "mmc3_config"; +}; diff --git a/Documentation/devicetree/bindings/clock/ti,cdce706.txt b/Documentation/devicetree/bindings/clock/ti,cdce706.txt new file mode 100644 index 000000000000..616836e7e1e2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti,cdce706.txt @@ -0,0 +1,42 @@ +Bindings for Texas Instruments CDCE706 programmable 3-PLL clock +synthesizer/multiplier/divider. + +Reference: http://www.ti.com/lit/ds/symlink/cdce706.pdf + +I2C device node required properties: +- compatible: shall be "ti,cdce706". +- reg: i2c device address, shall be in range [0x68...0x6b]. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock + handles, shall be reference clock(s) connected to CLK_IN0 + and CLK_IN1 pins. +- clock-names: shall be clk_in0 and/or clk_in1. Use clk_in0 + in case of crystal oscillator or differential signal input + configuration. Use clk_in0 and clk_in1 in case of independent + single-ended LVCMOS inputs configuration. + +Example: + + clocks { + clk54: clk54 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <54000000>; + }; + }; + ... + i2c0: i2c-master@0d090000 { + ... + cdce706: clock-synth@69 { + compatible = "ti,cdce706"; + #clock-cells = <1>; + reg = <0x69>; + clocks = <&clk54>; + clock-names = "clk_in0"; + }; + }; + ... + simple-audio-card,codec { + ... + clocks = <&cdce706 4>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/fapll.txt b/Documentation/devicetree/bindings/clock/ti/fapll.txt new file mode 100644 index 000000000000..c19b3f253b8c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/fapll.txt @@ -0,0 +1,33 @@ +Binding for Texas Instruments FAPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped FAPLL with usually two selectable input clocks +(reference clock and bypass clock), and one or more child +syntesizers. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dm816-fapll-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks (clk-ref and clk-bypass) +- reg : address and length of the register set for controlling the FAPLL. + +Examples: + main_fapll: main_fapll { + #clock-cells = <1>; + compatible = "ti,dm816-fapll-clock"; + reg = <0x400 0x40>; + clocks = <&sys_clkin_ck &sys_clkin_ck>; + clock-indices = <1>, <2>, <3>, <4>, <5>, + <6>, <7>; + clock-output-names = "main_pll_clk1", + "main_pll_clk2", + "main_pll_clk3", + "main_pll_clk4", + "main_pll_clk5", + "main_pll_clk6", + "main_pll_clk7"; + }; diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 91b3a3467150..4bf41d833804 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -10,8 +10,8 @@ Absolute maximum transfer rate is 200MB/s Required properties: - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc" - reg : mmc controller base registers - - clocks : a list with 2 phandle + clock specifier pairs - - clock-names : must contain "ahb" and "mmc" + - clocks : a list with 4 phandle + clock specifier pairs + - clock-names : must contain "ahb", "mmc", "output" and "sample" - interrupts : mmc controller interrupt Optional properties: @@ -25,8 +25,8 @@ Examples: mmc0: mmc@01c0f000 { compatible = "allwinner,sun5i-a13-mmc"; reg = <0x01c0f000 0x1000>; - clocks = <&ahb_gates 8>, <&mmc0_clk>; - clock-names = "ahb", "mod"; + clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>; + clock-names = "ahb", "mod", "output", "sample"; interrupts = <0 32 4>; status = "disabled"; }; |