diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 30 insertions, 4 deletions
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index 42941fdefb11..67da20539540 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -9,4 +9,6 @@ using one of the following compatible strings: allwinner,sun6i-a31 allwinner,sun7i-a20 allwinner,sun8i-a23 + allwinner,sun8i-a33 + allwinner,sun8i-h3 allwinner,sun9i-a80 diff --git a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt index e75f0e549fff..971c3eedb1c7 100644 --- a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt @@ -65,8 +65,10 @@ Optional properties: - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel -- port: A port node with endpoint definitions as defined in +- port@[0-1]: Port nodes with endpoint definitions as defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0 is the input port connected to the IPU display interface, + port 1 is the output port connected to a panel. example: @@ -75,9 +77,29 @@ display@di0 { edid = [edid-data]; interface-pix-fmt = "rgb24"; - port { + port@0 { + reg = <0>; + display_in: endpoint { remote-endpoint = <&ipu_di0_disp0>; }; }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; + +panel { + ... + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index c03eec116872..3443e0f838df 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -35,3 +35,6 @@ the PCIe specification. NOTE: this only applies to the SMMU itself, not masters connected upstream of the SMMU. + +- hisilicon,broken-prefetch-cmd + : Avoid sending CMD_PREFETCH_* commands to the SMMU. diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt index 938f8e1ba205..0db60470ebb6 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -8,6 +8,7 @@ of the EMIF IP and memory parts attached to it. Required properties: - compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> is the IP revision of the specific EMIF instance. + For am437x should be ti,emif-am4372. - phy-type : <u32> indicating the DDR phy type. Following are the allowed values diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 5d0376b8f202..211e7785f4d2 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -17,7 +17,6 @@ Required properties: "fsl,imx6sx-usdhc" Optional properties: -- fsl,cd-controller : Indicate to use controller internal card detection - fsl,wp-controller : Indicate to use controller internal write protection - fsl,delay-line : Specify the number of delay cells for override mode. This is used to set the clock delay for DLL(Delay Line) on override mode @@ -35,7 +34,6 @@ esdhc@70004000 { compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - fsl,cd-controller; fsl,wp-controller; }; |