diff options
Diffstat (limited to 'Documentation/devicetree')
9 files changed, 199 insertions, 55 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt index f2febb94550e..451fef26b4df 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt @@ -24,7 +24,7 @@ Optional properties: - fixed-link: When the GENET interface is connected to a MoCA hardware block or when operating in a RGMII to RGMII type of connection, or when the MDIO bus is voluntarily disabled, this property should be used to describe the "fixed link". - See Documentation/devicetree/bindings/net/fsl-tsec-phy.txt for information on + See Documentation/devicetree/bindings/net/fixed-link.txt for information on the property specifics Required child nodes: diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt new file mode 100644 index 000000000000..c183ea90d9bc --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt @@ -0,0 +1,29 @@ +* Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT) + +Required properties: +- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" +- reg: address and length of the register set for the device. +- interrupts: interrupts for the device, first cell must be for the the rx + interrupts, and the second cell should be for the transmit queues +- local-mac-address: Ethernet MAC address (48 bits) of this adapter +- phy-mode: Should be a string describing the PHY interface to the + Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt +- fixed-link: see Documentation/devicetree/bindings/net/fixed-link.txt for + the property specific details + +Optional properties: +- systemport,num-tier2-arb: number of tier 2 arbiters, an integer +- systemport,num-tier1-arb: number of tier 1 arbiters, an integer +- systemport,num-txq: number of HW transmit queues, an integer +- systemport,num-rxq: number of HW receive queues, an integer + +Example: +ethernet@f04a0000 { + compatible = "brcm,systemport-v1.00"; + reg = <0xf04a0000 0x4650>; + local-mac-address = [ 00 11 22 33 44 55 ]; + fixed-link = <0 1 1000 0 0>; + phy-mode = "gmii"; + interrupts = <0x0 0x16 0x0>, + <0x0 0x17 0x0>; +}; diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt index 7ff57a119f81..764c0c79b43d 100644 --- a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt +++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt @@ -2,7 +2,9 @@ TI CPSW Phy mode Selection Device Tree Bindings ----------------------------------------------- Required properties: -- compatible : Should be "ti,am3352-cpsw-phy-sel" +- compatible : Should be "ti,am3352-cpsw-phy-sel" for am335x platform and + "ti,dra7xx-cpsw-phy-sel" for dra7xx platform + "ti,am43xx-cpsw-phy-sel" for am43xx platform - reg : physical base address and size of the cpsw registers map - reg-names : names of the register map given in "reg" node diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt new file mode 100644 index 000000000000..82bf7e0f47b6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -0,0 +1,42 @@ +Fixed link Device Tree binding +------------------------------ + +Some Ethernet MACs have a "fixed link", and are not connected to a +normal MDIO-managed PHY device. For those situations, a Device Tree +binding allows to describe a "fixed link". + +Such a fixed link situation is described by creating a 'fixed-link' +sub-node of the Ethernet MAC device node, with the following +properties: + +* 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +* 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. +* 'pause' (boolean, optional), to indicate that pause should be + enabled. +* 'asym-pause' (boolean, optional), to indicate that asym_pause should + be enabled. + +Old, deprecated 'fixed-link' binding: + +* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the + form <a b c d e> with the following accepted values: + - a: emulated PHY ID, choose any but but unique to the all specified + fixed-links, from 0 to 31 + - b: duplex configuration: 0 for half duplex, 1 for full duplex + - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000 + - d: pause configuration: 0 for no pause, 1 for pause + - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for + asymmetric pause + +Example: + +ethernet@0 { + ... + fixed-link { + speed = <1000>; + full-duplex; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 737cdef4f903..be6ea8960f20 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -42,10 +42,7 @@ Properties: interrupt. For TSEC and eTSEC devices, the first interrupt is transmit, the second is receive, and the third is error. - phy-handle : See ethernet.txt file in the same directory. - - fixed-link : <a b c d e> where a is emulated phy id - choose any, - but unique to the all specified fixed-links, b is duplex - 0 half, - 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no - pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. + - fixed-link : See fixed-link.txt in the same directory. - phy-connection-type : See ethernet.txt file in the same directory. This property is only really needed if the connection is of type "rgmii-id", as all other connection types are detected by hardware. diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt new file mode 100644 index 000000000000..d3bbdded4cbe --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt @@ -0,0 +1,23 @@ +* AT86RF230 IEEE 802.15.4 * + +Required properties: + - compatible: should be "atmel,at86rf230", "atmel,at86rf231", + "atmel,at86rf233" or "atmel,at86rf212" + - spi-max-frequency: maximal bus speed, should be set to 7500000 depends + sync or async operation mode + - reg: the chipselect index + - interrupts: the interrupt generated by the device + +Optional properties: + - reset-gpio: GPIO spec for the rstn pin + - sleep-gpio: GPIO spec for the slp_tr pin + +Example: + + at86rf231@0 { + compatible = "atmel,at86rf231"; + spi-max-frequency = <7500000>; + reg = <0>; + interrupts = <19 1>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt b/Documentation/devicetree/bindings/net/micrel-ksz9021.txt deleted file mode 100644 index 997a63f1aea1..000000000000 --- a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt +++ /dev/null @@ -1,49 +0,0 @@ -Micrel KSZ9021 Gigabit Ethernet PHY - -Some boards require special tuning values, particularly when it comes to -clock delays. You can specify clock delay values by adding -micrel-specific properties to an Ethernet OF device node. - -All skew control options are specified in picoseconds. The minimum -value is 0, and the maximum value is 3000. - -Optional properties: - - rxc-skew-ps : Skew control of RXC pad - - rxdv-skew-ps : Skew control of RX CTL pad - - txc-skew-ps : Skew control of TXC pad - - txen-skew-ps : Skew control of TX_CTL pad - - rxd0-skew-ps : Skew control of RX data 0 pad - - rxd1-skew-ps : Skew control of RX data 1 pad - - rxd2-skew-ps : Skew control of RX data 2 pad - - rxd3-skew-ps : Skew control of RX data 3 pad - - txd0-skew-ps : Skew control of TX data 0 pad - - txd1-skew-ps : Skew control of TX data 1 pad - - txd2-skew-ps : Skew control of TX data 2 pad - - txd3-skew-ps : Skew control of TX data 3 pad - -Examples: - - /* Attach to an Ethernet device with autodetected PHY */ - &enet { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - status = "okay"; - }; - - /* Attach to an explicitly-specified PHY */ - mdio { - phy0: ethernet-phy@0 { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - reg = <0>; - }; - }; - ethernet@70000 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; - }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt new file mode 100644 index 000000000000..692076fda0e5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -0,0 +1,83 @@ +Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY + +Some boards require special tuning values, particularly when it comes to +clock delays. You can specify clock delay values by adding +micrel-specific properties to an Ethernet OF device node. + +Note that these settings are applied after any phy-specific fixup from +phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), +and therefore may overwrite them. + +KSZ9021: + + All skew control options are specified in picoseconds. The minimum + value is 0, the maximum value is 3000, and it is incremented by 200ps + steps. + + Optional properties: + + - rxc-skew-ps : Skew control of RXC pad + - rxdv-skew-ps : Skew control of RX CTL pad + - txc-skew-ps : Skew control of TXC pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +KSZ9031: + + All skew control options are specified in picoseconds. The minimum + value is 0, and the maximum is property-dependent. The increment + step is 60ps. + + Optional properties: + + Maximum value of 1860: + + - rxc-skew-ps : Skew control of RX clock pad + - txc-skew-ps : Skew control of TX clock pad + + Maximum value of 900: + + - rxdv-skew-ps : Skew control of RX CTL pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +Examples: + + /* Attach to an Ethernet device with autodetected PHY */ + &enet { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + status = "okay"; + }; + + /* Attach to an explicitly-specified PHY */ + mdio { + phy0: ethernet-phy@0 { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + reg = <0>; + }; + }; + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt new file mode 100644 index 000000000000..334eca2bf937 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-rhine.txt @@ -0,0 +1,17 @@ +* VIA Rhine 10/100 Network Controller + +Required properties: +- compatible : Should be "via,vt8500-rhine" for integrated + Rhine controllers found in VIA VT8500, WonderMedia WM8950 + and similar. These are listed as 1106:3106 rev. 0x84 on the + virtual PCI bus under vendor-provided kernels +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Examples: + +ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; +}; |