diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 115 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 379b84a567cc..1d25b04cd05e 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -12,6 +12,16 @@ Required properties: - interrupts: Should contain phy interrupt - fsl,anatop: phandle for anatop register, it is only for imx6 SoC series +Optional properties: +- fsl,tx-cal-45-dn-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DN output signal. Default: 45 +- fsl,tx-cal-45-dp-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DP output signal. Default: 45 +- fsl,tx-d-cal: Integer [79-119]. Current trimming value (as a percentage) of + the 17.78mA TX reference current. Default: 100 + Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 20a68bf2b4e7..7d16ebfaa5a1 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -26,7 +26,10 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. -- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. + +Deprecated properties: +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) + in gadget mode. Example: diff --git a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt new file mode 100644 index 000000000000..710b782ccf65 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt @@ -0,0 +1,28 @@ +Cavium SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "cavium,octeon-7130-usb-uctl" + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + uctl@1180069000000 { + compatible = "cavium,octeon-7130-usb-uctl"; + reg = <0x00011800 0x69000000 0x00000000 0x00000100>; + ranges; + #address-cells = <0x00000002>; + #size-cells = <0x00000002>; + refclk-frequency = <0x05f5e100>; + refclk-type-ss = "dlmc_ref_clk0"; + refclk-type-hs = "dlmc_ref_clk0"; + power = <0x00000002 0x00000002 0x00000001>; + xhci@1690000000000 { + compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3"; + reg = <0x00016900 0x00000000 0x00000010 0x00000000>; + interrupt-parent = <0x00000010>; + interrupts = <0x00000009 0x00000004>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7d7ce089b003..e3e6983288e3 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -13,7 +13,8 @@ Optional properties: in the array is expected to be a handle to the USB2/HS PHY and the second element is expected to be a handle to the USB3/SS PHY - phys: from the *Generic PHY* bindings - - phy-names: from the *Generic PHY* bindings + - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" + or "usb3-phy". - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. @@ -39,6 +40,11 @@ Optional properties: disabling the suspend signal to the PHY. - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection in PHY P3 power state. + - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists + in GUSB2PHYCFG, specify that USB2 PHY doesn't provide + a free-running PHY clock. + - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power + from P0 to P1/P2/P3 without delay. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index bba825711873..bfadeb1c3bab 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -11,6 +11,11 @@ Optional properties: "peripheral" and "otg". In case this attribute isn't passed via DT, USB DRD controllers should default to OTG. + - phy_type: tells USB controllers that we want to configure the core to support + a UTMI+ PHY with an 8- or 16-bit interface if UTMI+ is + selected. Valid arguments are "utmi" and "utmi_wide". + In case this isn't passed via DT, USB controllers should + default to HW capability. - otg-rev: tells usb driver the release number of the OTG and EH supplement with which the device and its descriptors are compliant, in binary-coded decimal (i.e. 2.0 is 0200H). This @@ -34,6 +39,7 @@ dwc3@4a030000 { usb-phy = <&usb2_phy>, <&usb3,phy>; maximum-speed = "super-speed"; dr_mode = "otg"; + phy_type = "utmi_wide"; otg-rev = <0x0200>; adp-disable; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index b6040563e51a..9e18e000339e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -9,6 +9,7 @@ Required properties: - "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device + - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt new file mode 100644 index 000000000000..0536a938e3ab --- /dev/null +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -0,0 +1,59 @@ +Rockchip SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "ref_clk" Controller reference clk, have to be 24 MHz + "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz + "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS + operation and >= 30MHz for HS operation + "grf_clk" Controller grf clk + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/rockchip,dwc3-usb-phy.txt + +Example device nodes: + + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_0: dwc3@fe800000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; + + usbdrd3_1: usb@fe900000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, + <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_1: dwc3@fe900000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe900000 0x0 0x100000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; |