diff options
Diffstat (limited to 'Documentation/driver-api/mtdnand.rst')
| -rw-r--r-- | Documentation/driver-api/mtdnand.rst | 34 |
1 files changed, 17 insertions, 17 deletions
diff --git a/Documentation/driver-api/mtdnand.rst b/Documentation/driver-api/mtdnand.rst index c55a6034c397..55447659b81f 100644 --- a/Documentation/driver-api/mtdnand.rst +++ b/Documentation/driver-api/mtdnand.rst @@ -180,10 +180,10 @@ by a chip select decoder. { struct nand_chip *this = mtd_to_nand(mtd); switch(cmd){ - case NAND_CTL_SETCLE: this->IO_ADDR_W |= CLE_ADRR_BIT; break; - case NAND_CTL_CLRCLE: this->IO_ADDR_W &= ~CLE_ADRR_BIT; break; - case NAND_CTL_SETALE: this->IO_ADDR_W |= ALE_ADRR_BIT; break; - case NAND_CTL_CLRALE: this->IO_ADDR_W &= ~ALE_ADRR_BIT; break; + case NAND_CTL_SETCLE: this->legacy.IO_ADDR_W |= CLE_ADRR_BIT; break; + case NAND_CTL_CLRCLE: this->legacy.IO_ADDR_W &= ~CLE_ADRR_BIT; break; + case NAND_CTL_SETALE: this->legacy.IO_ADDR_W |= ALE_ADRR_BIT; break; + case NAND_CTL_CLRALE: this->legacy.IO_ADDR_W &= ~ALE_ADRR_BIT; break; } } @@ -197,7 +197,7 @@ to read back the state of the pin. The function has no arguments and should return 0, if the device is busy (R/B pin is low) and 1, if the device is ready (R/B pin is high). If the hardware interface does not give access to the ready busy pin, then the function must not be defined -and the function pointer this->dev_ready is set to NULL. +and the function pointer this->legacy.dev_ready is set to NULL. Init function ------------- @@ -235,18 +235,18 @@ necessary information about the device. } /* Set address of NAND IO lines */ - this->IO_ADDR_R = baseaddr; - this->IO_ADDR_W = baseaddr; + this->legacy.IO_ADDR_R = baseaddr; + this->legacy.IO_ADDR_W = baseaddr; /* Reference hardware control function */ this->hwcontrol = board_hwcontrol; /* Set command delay time, see datasheet for correct value */ - this->chip_delay = CHIP_DEPENDEND_COMMAND_DELAY; + this->legacy.chip_delay = CHIP_DEPENDEND_COMMAND_DELAY; /* Assign the device ready function, if available */ - this->dev_ready = board_dev_ready; + this->legacy.dev_ready = board_dev_ready; this->eccmode = NAND_ECC_SOFT; /* Scan to find existence of the device */ - if (nand_scan (board_mtd, 1)) { + if (nand_scan (this, 1)) { err = -ENXIO; goto out_ior; } @@ -277,7 +277,7 @@ unregisters the partitions in the MTD layer. static void __exit board_cleanup (void) { /* Release resources, unregister device */ - nand_release (board_mtd); + nand_release (mtd_to_nand(board_mtd)); /* unmap physical address */ iounmap(baseaddr); @@ -336,17 +336,17 @@ connected to an address decoder. struct nand_chip *this = mtd_to_nand(mtd); /* Deselect all chips */ - this->IO_ADDR_R &= ~BOARD_NAND_ADDR_MASK; - this->IO_ADDR_W &= ~BOARD_NAND_ADDR_MASK; + this->legacy.IO_ADDR_R &= ~BOARD_NAND_ADDR_MASK; + this->legacy.IO_ADDR_W &= ~BOARD_NAND_ADDR_MASK; switch (chip) { case 0: - this->IO_ADDR_R |= BOARD_NAND_ADDR_CHIP0; - this->IO_ADDR_W |= BOARD_NAND_ADDR_CHIP0; + this->legacy.IO_ADDR_R |= BOARD_NAND_ADDR_CHIP0; + this->legacy.IO_ADDR_W |= BOARD_NAND_ADDR_CHIP0; break; .... case n: - this->IO_ADDR_R |= BOARD_NAND_ADDR_CHIPn; - this->IO_ADDR_W |= BOARD_NAND_ADDR_CHIPn; + this->legacy.IO_ADDR_R |= BOARD_NAND_ADDR_CHIPn; + this->legacy.IO_ADDR_W |= BOARD_NAND_ADDR_CHIPn; break; } } |