diff options
Diffstat (limited to 'Documentation/frv/booting.txt')
| -rw-r--r-- | Documentation/frv/booting.txt | 182 |
1 files changed, 0 insertions, 182 deletions
diff --git a/Documentation/frv/booting.txt b/Documentation/frv/booting.txt deleted file mode 100644 index cd9dc1dfb144..000000000000 --- a/Documentation/frv/booting.txt +++ /dev/null @@ -1,182 +0,0 @@ - ========================= - BOOTING FR-V LINUX KERNEL - ========================= - -====================== -PROVIDING A FILESYSTEM -====================== - -First of all, a root filesystem must be made available. This can be done in -one of two ways: - - (1) NFS Export - - A filesystem should be constructed in a directory on an NFS server that - the target board can reach. This directory should then be NFS exported - such that the target board can read and write into it as root. - - (2) Flash Filesystem (JFFS2 Recommended) - - In this case, the image must be stored or built up on flash before it - can be used. A complete image can be built using the mkfs.jffs2 or - similar program and then downloaded and stored into flash by RedBoot. - - -======================== -LOADING THE KERNEL IMAGE -======================== - -The kernel will need to be loaded into RAM by RedBoot (or by some alternative -boot loader) before it can be run. The kernel image (arch/frv/boot/Image) may -be loaded in one of three ways: - - (1) Load from Flash - - This is the simplest. RedBoot can store an image in the flash (see the - RedBoot documentation) and then load it back into RAM. RedBoot keeps - track of the load address, entry point and size, so the command to do - this is simply: - - fis load linux - - The image is then ready to be executed. - - (2) Load by TFTP - - The following command will download a raw binary kernel image from the - default server (as negotiated by BOOTP) and store it into RAM: - - load -b 0x00100000 -r /tftpboot/image.bin - - The image is then ready to be executed. - - (3) Load by Y-Modem - - The following command will download a raw binary kernel image across the - serial port that RedBoot is currently using: - - load -m ymodem -b 0x00100000 -r zImage - - The serial client (such as minicom) must then be told to transmit the - program by Y-Modem. - - When finished, the image will then be ready to be executed. - - -================== -BOOTING THE KERNEL -================== - -Boot the image with the following RedBoot command: - - exec -c "<CMDLINE>" 0x00100000 - -For example: - - exec -c "console=ttySM0,115200 ip=:::::dhcp root=/dev/mtdblock2 rw" - -This will start the kernel running. Note that if the GDB-stub is compiled in, -then the kernel will immediately wait for GDB to connect over serial before -doing anything else. See the section on kernel debugging with GDB. - -The kernel command line <CMDLINE> tells the kernel where its console is and -how to find its root filesystem. This is made up of the following components, -separated by spaces: - - (*) console=ttyS<x>[,<baud>[<parity>[<bits>[<flow>]]]] - - This specifies that the system console should output through on-chip - serial port <x> (which can be "0" or "1"). - - <baud> is a standard baud rate between 1200 and 115200 (default 9600). - - <parity> is a parity setting of "N", "O", "E", "M" or "S" for None, Odd, - Even, Mark or Space. "None" is the default. - - <stop> is "7" or "8" for the number of bits per character. "8" is the - default. - - <flow> is "r" to use flow control (XCTS on serial port 2 only). The - default is to not use flow control. - - For example: - - console=ttyS0,115200 - - To use the first on-chip serial port at baud rate 115200, no parity, 8 - bits, and no flow control. - - (*) root=<xxxx> - - This specifies the device upon which the root filesystem resides. It - may be specified by major and minor number, device path, or even - partition uuid, if supported. For example: - - /dev/nfs NFS root filesystem - /dev/mtdblock3 Fourth RedBoot partition on the System Flash - PARTUUID=00112233-4455-6677-8899-AABBCCDDEEFF/PARTNROFF=1 - first partition after the partition with the given UUID - 253:0 Device with major 253 and minor 0 - - Authoritative information can be found in - "Documentation/admin-guide/kernel-parameters.rst". - - (*) rw - - Start with the root filesystem mounted Read/Write. - - The remaining components are all optional: - - (*) ip=<ip>::::<host>:<iface>:<cfg> - - Configure the network interface. If <cfg> is "off" then <ip> should - specify the IP address for the network device <iface>. <host> provide - the hostname for the device. - - If <cfg> is "bootp" or "dhcp", then all of these parameters will be - discovered by consulting a BOOTP or DHCP server. - - For example, the following might be used: - - ip=192.168.73.12::::frv:eth0:off - - This sets the IP address on the VDK motherboard RTL8029 ethernet chipset - (eth0) to be 192.168.73.12, and sets the board's hostname to be "frv". - - (*) nfsroot=<server>:<dir>[,v<vers>] - - This is mandatory if "root=/dev/nfs" is given as an option. It tells the - kernel the IP address of the NFS server providing its root filesystem, - and the pathname on that server of the filesystem. - - The NFS version to use can also be specified. v2 and v3 are supported by - Linux. - - For example: - - nfsroot=192.168.73.1:/nfsroot-frv - - (*) profile=1 - - Turns on the kernel profiler (accessible through /proc/profile). - - (*) console=gdb0 - - This can be used as an alternative to the "console=ttyS..." listed - above. I tells the kernel to pass the console output to GDB if the - gdbstub is compiled in to the kernel. - - If this is used, then the gdbstub passes the text to GDB, which then - simply dumps it to its standard output. - - (*) mem=<xxx>M - - Normally the kernel will work out how much SDRAM it has by reading the - SDRAM controller registers. That can be overridden with this - option. This allows the kernel to be told that it has <xxx> megabytes of - memory available. - - (*) init=<prog> [<arg> [<arg> [<arg> ...]]] - - This tells the kernel what program to run initially. By default this is - /sbin/init, but /sbin/sash or /bin/sh are common alternatives. |