diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/coretemp | 105 | ||||
| -rw-r--r-- | Documentation/hwmon/f71882fg | 4 | ||||
| -rw-r--r-- | Documentation/hwmon/jc42 | 97 | ||||
| -rw-r--r-- | Documentation/hwmon/pkgtemp | 36 | ||||
| -rw-r--r-- | Documentation/hwmon/smm665 | 157 |
5 files changed, 397 insertions, 2 deletions
diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index 92267b62db59..25568f844804 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -21,8 +21,8 @@ Temperature is measured in degrees Celsius and measurement resolution is 1 degree C. Valid temperatures are from 0 to TjMax degrees C, because the actual value of temperature register is in fact a delta from TjMax. -Temperature known as TjMax is the maximum junction temperature of processor. -Intel defines this temperature as 85C or 100C. At this temperature, protection +Temperature known as TjMax is the maximum junction temperature of processor, +which depends on the CPU model. See table below. At this temperature, protection mechanism will perform actions to forcibly cool down the processor. Alarm may be raised, if the temperature grows enough (more than TjMax) to trigger the Out-Of-Spec bit. Following table summarizes the exported sysfs files: @@ -38,3 +38,104 @@ temp1_label - Contains string "Core X", where X is processor The TjMax temperature is set to 85 degrees C if undocumented model specific register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as (sometimes) documented in processor datasheet. + +Appendix A. Known TjMax lists (TBD): +Some information comes from ark.intel.com + +Process Processor TjMax(C) + +32nm Core i3/i5/i7 Processors + i7 660UM/640/620, 640LM/620, 620M, 610E 105 + i5 540UM/520/430, 540M/520/450/430 105 + i3 330E, 370M/350/330 90 rPGA, 105 BGA + i3 330UM 105 + +32nm Core i7 Extreme Processors + 980X 100 + +32nm Celeron Processors + U3400 105 + P4505/P4500 90 + +45nm Xeon Processors 5400 Quad-Core + X5492, X5482, X5472, X5470, X5460, X5450 85 + E5472, E5462, E5450/40/30/20/10/05 85 + L5408 95 + L5430, L5420, L5410 70 + +45nm Xeon Processors 5200 Dual-Core + X5282, X5272, X5270, X5260 90 + E5240 90 + E5205, E5220 70, 90 + L5240 70 + L5238, L5215 95 + +45nm Atom Processors + D525/510/425/410 100 + Z560/550/540/530P/530/520PT/520/515/510PT/510P 90 + Z510/500 90 + N475/470/455/450 100 + N280/270 90 + 330/230 125 + +45nm Core2 Processors + Solo ULV SU3500/3300 100 + T9900/9800/9600/9550/9500/9400/9300/8300/8100 105 + T6670/6500/6400 105 + T6600 90 + SU9600/9400/9300 105 + SP9600/9400 105 + SL9600/9400/9380/9300 105 + P9700/9600/9500/8800/8700/8600/8400/7570 105 + P7550/7450 90 + +45nm Core2 Quad Processors + Q9100/9000 100 + +45nm Core2 Extreme Processors + X9100/9000 105 + QX9300 100 + +45nm Core i3/i5/i7 Processors + i7 940XM/920 100 + i7 840QM/820/740/720 100 + +45nm Celeron Processors + SU2300 100 + 900 105 + +65nm Core2 Duo Processors + Solo U2200, U2100 100 + U7700/7600/7500 100 + T7800/7700/7600/7500/7400/7300/7250/7200/7100 100 + T5870/5670/5600/5550/5500/5470/5450/5300/5270 100 + T5250 100 + T5800/5750/5200 85 + L7700/7500/7400/7300/7200 100 + +65nm Core2 Extreme Processors + X7900/7800 100 + +65nm Core Duo Processors + U2500/2400 100 + T2700/2600/2450/2400/2350/2300E/2300/2250/2050 100 + L2500/2400/2300 100 + +65nm Core Solo Processors + U1500/1400/1300 100 + T1400/1350/1300/1250 100 + +65nm Xeon Processors 5000 Quad-Core + X5000 90-95 + E5000 80 + L5000 70 + L5318 95 + +65nm Xeon Processors 5000 Dual-Core + 5080, 5063, 5060, 5050, 5030 80-90 + 5160, 5150, 5148, 5140, 5130, 5120, 5110 80 + L5138 100 + +65nm Celeron Processors + T1700/1600 100 + 560/550/540/530 100 diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg index a7952c2bd959..1a07fd674cd0 100644 --- a/Documentation/hwmon/f71882fg +++ b/Documentation/hwmon/f71882fg @@ -2,6 +2,10 @@ Kernel driver f71882fg ====================== Supported chips: + * Fintek F71808E + Prefix: 'f71808fg' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public * Fintek F71858FG Prefix: 'f71858fg' Addresses scanned: none, address read from Super I/O config space diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 new file mode 100644 index 000000000000..0e76ef12e4c6 --- /dev/null +++ b/Documentation/hwmon/jc42 @@ -0,0 +1,97 @@ +Kernel driver jc42 +================== + +Supported chips: + * Analog Devices ADT7408 + Prefix: 'adt7408' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf + * IDT TSE2002B3, TS3000B3 + Prefix: 'tse2002b3', 'ts3000b3' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.idt.com/products/getdoc.cfm?docid=18715691 + http://www.idt.com/products/getdoc.cfm?docid=18715692 + * Maxim MAX6604 + Prefix: 'max6604' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf + * Microchip MCP9805, MCP98242, MCP98243, MCP9843 + Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf + http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf + * NXP Semiconductors SE97, SE97B + Prefix: 'se97' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.nxp.com/documents/data_sheet/SE97.pdf + http://www.nxp.com/documents/data_sheet/SE97B.pdf + * NXP Semiconductors SE98 + Prefix: 'se98' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.nxp.com/documents/data_sheet/SE98.pdf + * ON Semiconductor CAT34TS02, CAT6095 + Prefix: 'cat34ts02', 'cat6095' + Addresses scanned: I2C 0x18 - 0x1f + Datasheet: + http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF + http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF + * ST Microelectronics STTS424, STTS424E02 + Prefix: 'stts424' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf + http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf + * JEDEC JC 42.4 compliant temperature sensor chips + Prefix: 'jc42' + Addresses scanned: I2C 0x18 - 0x1f + Datasheet: - + +Author: + Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver implements support for JEDEC JC 42.4 compliant temperature sensors. +The driver auto-detects the chips listed above, but can be manually instantiated +to support other JC 42.4 compliant chips. + +Example: the following will load the driver for a generic JC 42.4 compliant +temperature sensor at address 0x18 on I2C bus #1: + +# modprobe jc42 +# echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device + +A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum, +and critical temperature can be configured. There are alarms for high, low, +and critical thresholds. + +There is also an hysteresis to control the thresholds for resetting alarms. +Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5, +3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those +limits. The chip supports only a single register to configure the hysteresis, +which applies to all limits. This register can be written by writing into +temp1_crit_hyst. Other hysteresis attributes are read-only. + +Sysfs entries +------------- + +temp1_input Temperature (RO) +temp1_min Minimum temperature (RW) +temp1_max Maximum temperature (RW) +temp1_crit Critical high temperature (RW) + +temp1_crit_hyst Critical hysteresis temperature (RW) +temp1_max_hyst Maximum hysteresis temperature (RO) + +temp1_min_alarm Temperature low alarm +temp1_max_alarm Temperature high alarm +temp1_crit_alarm Temperature critical alarm diff --git a/Documentation/hwmon/pkgtemp b/Documentation/hwmon/pkgtemp new file mode 100644 index 000000000000..c8e1fb0fadd3 --- /dev/null +++ b/Documentation/hwmon/pkgtemp @@ -0,0 +1,36 @@ +Kernel driver pkgtemp +====================== + +Supported chips: + * Intel family + Prefix: 'pkgtemp' + CPUID: + Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual + Volume 3A: System Programming Guide + +Author: Fenghua Yu + +Description +----------- + +This driver permits reading package level temperature sensor embedded inside +Intel CPU package. The sensors can be in core, uncore, memory controller, or +other components in a package. The feature is first implemented in Intel Sandy +Bridge platform. + +Temperature is measured in degrees Celsius and measurement resolution is +1 degree C. Valid temperatures are from 0 to TjMax degrees C, because the actual +value of temperature register is in fact a delta from TjMax. + +Temperature known as TjMax is the maximum junction temperature of package. +We get this from MSR_IA32_TEMPERATURE_TARGET. If the MSR is not accessible, +we define TjMax as 100 degrees Celsius. At this temperature, protection +mechanism will perform actions to forcibly cool down the package. Alarm +may be raised, if the temperature grows enough (more than TjMax) to trigger +the Out-Of-Spec bit. Following table summarizes the exported sysfs files: + +temp1_input - Package temperature (in millidegrees Celsius). +temp1_max - All cooling devices should be turned on. +temp1_crit - Maximum junction temperature (in millidegrees Celsius). +temp1_crit_alarm - Set when Out-of-spec bit is set, never clears. + Correct CPU operation is no longer guaranteed. diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 new file mode 100644 index 000000000000..3820fc9ca52d --- /dev/null +++ b/Documentation/hwmon/smm665 @@ -0,0 +1,157 @@ +Kernel driver smm665 +==================== + +Supported chips: + * Summit Microelectronics SMM465 + Prefix: 'smm465' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf + * Summit Microelectronics SMM665, SMM665B + Prefix: 'smm665' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf + * Summit Microelectronics SMM665C + Prefix: 'smm665c' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf + * Summit Microelectronics SMM764 + Prefix: 'smm764' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf + * Summit Microelectronics SMM766, SMM766B + Prefix: 'smm766' + Addresses scanned: - + Datasheets: + http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf + http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Module Parameters +----------------- + +* vref: int + Default: 1250 (mV) + Reference voltage on VREF_ADC pin in mV. It should not be necessary to set + this parameter unless a non-default reference voltage is used. + + +Description +----------- + +[From datasheet] The SMM665 is an Active DC Output power supply Controller +that monitors, margins and cascade sequences power. The part monitors six +power supply channels as well as VDD, 12V input, two general-purpose analog +inputs and an internal temperature sensor using a 10-bit ADC. + +Each monitored channel has its own high and low limits, plus a critical +limit. + +Support for SMM465, SMM764, and SMM766 has been implemented but is untested. + + +Usage Notes +----------- + +This driver does not probe for devices, since there is no register which +can be safely used to identify the chip. You will have to instantiate +the devices explicitly. When instantiating the device, you have to specify +its configuration register address. + +Example: the following will load the driver for an SMM665 at address 0x57 +on I2C bus #1: +$ modprobe smm665 +$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +This driver uses the values in the datasheet to convert ADC register values +into the values specified in the sysfs-interface document. All attributes are +read only. + +Min, max, lcrit, and crit values are used by the chip to trigger external signals +and/or other activity. Triggered signals can include HEALTHY, RST, Power Off, +or Fault depending on the chip configuration. The driver reports values as lcrit +or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or +max otherwise. For details please see the SMM665 datasheet. + +For SMM465 and SMM764, values for Channel E and F are reported but undefined. + +in1_input 12V input voltage (mV) +in2_input 3.3V (VDD) input voltage (mV) +in3_input Channel A voltage (mV) +in4_input Channel B voltage (mV) +in5_input Channel C voltage (mV) +in6_input Channel D voltage (mV) +in7_input Channel E voltage (mV) +in8_input Channel F voltage (mV) +in9_input AIN1 voltage (mV) +in10_input AIN2 voltage (mV) + +in1_min 12v input minimum voltage (mV) +in2_min 3.3V (VDD) input minimum voltage (mV) +in3_min Channel A minimum voltage (mV) +in4_min Channel B minimum voltage (mV) +in5_min Channel C minimum voltage (mV) +in6_min Channel D minimum voltage (mV) +in7_min Channel E minimum voltage (mV) +in8_min Channel F minimum voltage (mV) +in9_min AIN1 minimum voltage (mV) +in10_min AIN2 minimum voltage (mV) + +in1_max 12v input maximum voltage (mV) +in2_max 3.3V (VDD) input maximum voltage (mV) +in3_max Channel A maximum voltage (mV) +in4_max Channel B maximum voltage (mV) +in5_max Channel C maximum voltage (mV) +in6_max Channel D maximum voltage (mV) +in7_max Channel E maximum voltage (mV) +in8_max Channel F maximum voltage (mV) +in9_max AIN1 maximum voltage (mV) +in10_max AIN2 maximum voltage (mV) + +in1_lcrit 12v input critical minimum voltage (mV) +in2_lcrit 3.3V (VDD) input critical minimum voltage (mV) +in3_lcrit Channel A critical minimum voltage (mV) +in4_lcrit Channel B critical minimum voltage (mV) +in5_lcrit Channel C critical minimum voltage (mV) +in6_lcrit Channel D critical minimum voltage (mV) +in7_lcrit Channel E critical minimum voltage (mV) +in8_lcrit Channel F critical minimum voltage (mV) +in9_lcrit AIN1 critical minimum voltage (mV) +in10_lcrit AIN2 critical minimum voltage (mV) + +in1_crit 12v input critical maximum voltage (mV) +in2_crit 3.3V (VDD) input critical maximum voltage (mV) +in3_crit Channel A critical maximum voltage (mV) +in4_crit Channel B critical maximum voltage (mV) +in5_crit Channel C critical maximum voltage (mV) +in6_crit Channel D critical maximum voltage (mV) +in7_crit Channel E critical maximum voltage (mV) +in8_crit Channel F critical maximum voltage (mV) +in9_crit AIN1 critical maximum voltage (mV) +in10_crit AIN2 critical maximum voltage (mV) + +in1_crit_alarm 12v input critical alarm +in2_crit_alarm 3.3V (VDD) input critical alarm +in3_crit_alarm Channel A critical alarm +in4_crit_alarm Channel B critical alarm +in5_crit_alarm Channel C critical alarm +in6_crit_alarm Channel D critical alarm +in7_crit_alarm Channel E critical alarm +in8_crit_alarm Channel F critical alarm +in9_crit_alarm AIN1 critical alarm +in10_crit_alarm AIN2 critical alarm + +temp1_input Chip tempererature +temp1_min Mimimum chip tempererature +temp1_max Maximum chip tempererature +temp1_crit Critical chip tempererature +temp1_crit_alarm Temperature critical alarm |