diff options
Diffstat (limited to 'Documentation/i2c/chips/w83781d')
| -rw-r--r-- | Documentation/i2c/chips/w83781d | 402 |
1 files changed, 0 insertions, 402 deletions
diff --git a/Documentation/i2c/chips/w83781d b/Documentation/i2c/chips/w83781d deleted file mode 100644 index e5459333ba68..000000000000 --- a/Documentation/i2c/chips/w83781d +++ /dev/null @@ -1,402 +0,0 @@ -Kernel driver w83781d -===================== - -Supported chips: - * Winbond W83781D - Prefix: 'w83781d' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) - Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83781d.pdf - * Winbond W83782D - Prefix: 'w83782d' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) - Datasheet: http://www.winbond.com/PDF/sheet/w83782d.pdf - * Winbond W83783S - Prefix: 'w83783s' - Addresses scanned: I2C 0x2d - Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83783s.pdf - * Winbond W83627HF - Prefix: 'w83627hf' - Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) - Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf - * Asus AS99127F - Prefix: 'as99127f' - Addresses scanned: I2C 0x28 - 0x2f - Datasheet: Unavailable from Asus - -Authors: - Frodo Looijaard <frodol@dds.nl>, - Philip Edelbrock <phil@netroedge.com>, - Mark Studebaker <mdsxyz123@yahoo.com> - -Module parameters ------------------ - -* init int - (default 1) - Use 'init=0' to bypass initializing the chip. - Try this if your computer crashes when you load the module. - -force_subclients=bus,caddr,saddr,saddr - This is used to force the i2c addresses for subclients of - a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b' - to force the subclients of chip 0x2d on bus 0 to i2c addresses - 0x4a and 0x4b. This parameter is useful for certain Tyan boards. - -Description ------------ - -This driver implements support for the Winbond W83781D, W83782D, W83783S, -W83627HF chips, and the Asus AS99127F chips. We will refer to them -collectively as W8378* chips. - -There is quite some difference between these chips, but they are similar -enough that it was sensible to put them together in one driver. -The W83627HF chip is assumed to be identical to the ISA W83782D. -The Asus chips are similar to an I2C-only W83782D. - -Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA -as99127f 7 3 0 3 0x31 0x12c3 yes no -as99127f rev.2 (type_name = as99127f) 0x31 0x5ca3 yes no -w83781d 7 3 0 3 0x10-1 0x5ca3 yes yes -w83627hf 9 3 2 3 0x21 0x5ca3 yes yes(LPC) -w83782d 9 3 2-4 3 0x30 0x5ca3 yes yes -w83783s 5-6 3 2 1-2 0x40 0x5ca3 yes no - -Detection of these chips can sometimes be foiled because they can be in -an internal state that allows no clean access. If you know the address -of the chip, use a 'force' parameter; this will put them into a more -well-behaved state first. - -The W8378* implements temperature sensors (three on the W83781D and W83782D, -two on the W83783S), three fan rotation speed sensors, voltage sensors -(seven on the W83781D, nine on the W83782D and six on the W83783S), VID -lines, alarms with beep warnings, and some miscellaneous stuff. - -Temperatures are measured in degrees Celsius. There is always one main -temperature sensor, and one (W83783S) or two (W83781D and W83782D) other -sensors. An alarm is triggered for the main sensor once when the -Overtemperature Shutdown limit is crossed; it is triggered again as soon as -it drops below the Hysteresis value. A more useful behavior -can be found by setting the Hysteresis value to +127 degrees Celsius; in -this case, alarms are issued during all the time when the actual temperature -is above the Overtemperature Shutdown value. The driver sets the -hysteresis value for temp1 to 127 at initialization. - -For the other temperature sensor(s), an alarm is triggered when the -temperature gets higher then the Overtemperature Shutdown value; it stays -on until the temperature falls below the Hysteresis value. But on the -W83781D, there is only one alarm that functions for both other sensors! -Temperatures are guaranteed within a range of -55 to +125 degrees. The -main temperature sensors has a resolution of 1 degree; the other sensor(s) -of 0.5 degree. - -Fan rotation speeds are reported in RPM (rotations per minute). An alarm is -triggered if the rotation speed has dropped below a programmable limit. Fan -readings can be divided by a programmable divider (1, 2, 4 or 8 for the -W83781D; 1, 2, 4, 8, 16, 32, 64 or 128 for the others) to give -the readings more range or accuracy. Not all RPM values can accurately -be represented, so some rounding is done. With a divider of 2, the lowest -representable value is around 2600 RPM. - -Voltage sensors (also known as IN sensors) report their values in volts. -An alarm is triggered if the voltage has crossed a programmable minimum -or maximum limit. Note that minimum in this case always means 'closest to -zero'; this is important for negative voltage measurements. All voltage -inputs can measure voltages between 0 and 4.08 volts, with a resolution -of 0.016 volt. - -The VID lines encode the core voltage value: the voltage level your processor -should work with. This is hardcoded by the mainboard and/or processor itself. -It is a value in volts. When it is unconnected, you will often find the -value 3.50 V here. - -The W83782D and W83783S temperature conversion machine understands about -several kinds of temperature probes. You can program the so-called -beta value in the sensor files. '1' is the PII/Celeron diode, '2' is the -TN3904 transistor, and 3435 the default thermistor value. Other values -are (not yet) supported. - -In addition to the alarms described above, there is a CHAS alarm on the -chips which triggers if your computer case is open. - -When an alarm goes off, you can be warned by a beeping signal through -your computer speaker. It is possible to enable all beeping globally, -or only the beeping for some alarms. - -If an alarm triggers, it will remain triggered until the hardware register -is read at least once. This means that the cause for the alarm may -already have disappeared! Note that in the current implementation, all -hardware registers are read whenever any data is read (unless it is less -than 1.5 seconds since the last update). This means that you can easily -miss once-only alarms. - -The chips only update values each 1.5 seconds; reading them more often -will do no harm, but will return 'old' values. - -AS99127F PROBLEMS ------------------ -The as99127f support was developed without the benefit of a datasheet. -In most cases it is treated as a w83781d (although revision 2 of the -AS99127F looks more like a w83782d). -This support will be BETA until a datasheet is released. -One user has reported problems with fans stopping -occasionally. - -Note that the individual beep bits are inverted from the other chips. -The driver now takes care of this so that user-space applications -don't have to know about it. - -Known problems: - - Problems with diode/thermistor settings (supported?) - - One user reports fans stopping under high server load. - - Revision 2 seems to have 2 PWM registers but we don't know - how to handle them. More details below. - -These will not be fixed unless we get a datasheet. -If you have problems, please lobby Asus to release a datasheet. -Unfortunately several others have without success. -Please do not send mail to us asking for better as99127f support. -We have done the best we can without a datasheet. -Please do not send mail to the author or the sensors group asking for -a datasheet or ideas on how to convince Asus. We can't help. - - -NOTES: ------ - 783s has no in1 so that in[2-6] are compatible with the 781d/782d. - - 783s pin is programmable for -5V or temp1; defaults to -5V, - no control in driver so temp1 doesn't work. - - 782d and 783s datasheets differ on which is pwm1 and which is pwm2. - We chose to follow 782d. - - 782d and 783s pin is programmable for fan3 input or pwm2 output; - defaults to fan3 input. - If pwm2 is enabled (with echo 255 1 > pwm2), then - fan3 will report 0. - - 782d has pwm1-2 for ISA, pwm1-4 for i2c. (pwm3-4 share pins with - the ISA pins) - -Data sheet updates: ------------------- - - PWM clock registers: - - 000: master / 512 - 001: master / 1024 - 010: master / 2048 - 011: master / 4096 - 100: master / 8192 - - -Answers from Winbond tech support ---------------------------------- -> -> 1) In the W83781D data sheet section 7.2 last paragraph, it talks about -> reprogramming the R-T table if the Beta of the thermistor is not -> 3435K. The R-T table is described briefly in section 8.20. -> What formulas do I use to program a new R-T table for a given Beta? -> - We are sorry that the calculation for R-T table value is -confidential. If you have another Beta value of thermistor, we can help -to calculate the R-T table for you. But you should give us real R-T -Table which can be gotten by thermistor vendor. Therefore we will calculate -them and obtain 32-byte data, and you can fill the 32-byte data to the -register in Bank0.CR51 of W83781D. - - -> 2) In the W83782D data sheet, it mentions that pins 38, 39, and 40 are -> programmable to be either thermistor or Pentium II diode inputs. -> How do I program them for diode inputs? I can't find any register -> to program these to be diode inputs. - --> You may program Bank0 CR[5Dh] and CR[59h] registers. - - CR[5Dh] bit 1(VTIN1) bit 2(VTIN2) bit 3(VTIN3) - - thermistor 0 0 0 - diode 1 1 1 - - -(error) CR[59h] bit 4(VTIN1) bit 2(VTIN2) bit 3(VTIN3) -(right) CR[59h] bit 4(VTIN1) bit 5(VTIN2) bit 6(VTIN3) - - PII thermal diode 1 1 1 - 2N3904 diode 0 0 0 - - -Asus Clones ------------ - -We have no datasheets for the Asus clones (AS99127F and ASB100 Bach). -Here are some very useful information that were given to us by Alex Van -Kaam about how to detect these chips, and how to read their values. He -also gives advice for another Asus chipset, the Mozart-2 (which we -don't support yet). Thanks Alex! -I reworded some parts and added personal comments. - -# Detection: - -AS99127F rev.1, AS99127F rev.2 and ASB100: -- I2C address range: 0x29 - 0x2F -- If register 0x58 holds 0x31 then we have an Asus (either ASB100 or - AS99127F) -- Which one depends on register 0x4F (manufacturer ID): - 0x06 or 0x94: ASB100 - 0x12 or 0xC3: AS99127F rev.1 - 0x5C or 0xA3: AS99127F rev.2 - Note that 0x5CA3 is Winbond's ID (WEC), which let us think Asus get their - AS99127F rev.2 direct from Winbond. The other codes mean ATT and DVC, - respectively. ATT could stand for Asustek something (although it would be - very badly chosen IMHO), I don't know what DVC could stand for. Maybe - these codes simply aren't meant to be decoded that way. - -Mozart-2: -- I2C address: 0x77 -- If register 0x58 holds 0x56 or 0x10 then we have a Mozart-2 -- Of the Mozart there are 3 types: - 0x58=0x56, 0x4E=0x94, 0x4F=0x36: Asus ASM58 Mozart-2 - 0x58=0x56, 0x4E=0x94, 0x4F=0x06: Asus AS2K129R Mozart-2 - 0x58=0x10, 0x4E=0x5C, 0x4F=0xA3: Asus ??? Mozart-2 - You can handle all 3 the exact same way :) - -# Temperature sensors: - -ASB100: -- sensor 1: register 0x27 -- sensor 2 & 3 are the 2 LM75's on the SMBus -- sensor 4: register 0x17 -Remark: I noticed that on Intel boards sensor 2 is used for the CPU - and 4 is ignored/stuck, on AMD boards sensor 4 is the CPU and sensor 2 is - either ignored or a socket temperature. - -AS99127F (rev.1 and 2 alike): -- sensor 1: register 0x27 -- sensor 2 & 3 are the 2 LM75's on the SMBus -Remark: Register 0x5b is suspected to be temperature type selector. Bit 1 - would control temp1, bit 3 temp2 and bit 5 temp3. - -Mozart-2: -- sensor 1: register 0x27 -- sensor 2: register 0x13 - -# Fan sensors: - -ASB100, AS99127F (rev.1 and 2 alike): -- 3 fans, identical to the W83781D - -Mozart-2: -- 2 fans only, 1350000/RPM/div -- fan 1: register 0x28, divisor on register 0xA1 (bits 4-5) -- fan 2: register 0x29, divisor on register 0xA1 (bits 6-7) - -# Voltages: - -This is where there is a difference between AS99127F rev.1 and 2. -Remark: The difference is similar to the difference between - W83781D and W83782D. - -ASB100: -in0=r(0x20)*0.016 -in1=r(0x21)*0.016 -in2=r(0x22)*0.016 -in3=r(0x23)*0.016*1.68 -in4=r(0x24)*0.016*3.8 -in5=r(0x25)*(-0.016)*3.97 -in6=r(0x26)*(-0.016)*1.666 - -AS99127F rev.1: -in0=r(0x20)*0.016 -in1=r(0x21)*0.016 -in2=r(0x22)*0.016 -in3=r(0x23)*0.016*1.68 -in4=r(0x24)*0.016*3.8 -in5=r(0x25)*(-0.016)*3.97 -in6=r(0x26)*(-0.016)*1.503 - -AS99127F rev.2: -in0=r(0x20)*0.016 -in1=r(0x21)*0.016 -in2=r(0x22)*0.016 -in3=r(0x23)*0.016*1.68 -in4=r(0x24)*0.016*3.8 -in5=(r(0x25)*0.016-3.6)*5.14+3.6 -in6=(r(0x26)*0.016-3.6)*3.14+3.6 - -Mozart-2: -in0=r(0x20)*0.016 -in1=255 -in2=r(0x22)*0.016 -in3=r(0x23)*0.016*1.68 -in4=r(0x24)*0.016*4 -in5=255 -in6=255 - - -# PWM - -Additional info about PWM on the AS99127F (may apply to other Asus -chips as well) by Jean Delvare as of 2004-04-09: - -AS99127F revision 2 seems to have two PWM registers at 0x59 and 0x5A, -and a temperature sensor type selector at 0x5B (which basically means -that they swapped registers 0x59 and 0x5B when you compare with Winbond -chips). -Revision 1 of the chip also has the temperature sensor type selector at -0x5B, but PWM registers have no effect. - -We don't know exactly how the temperature sensor type selection works. -Looks like bits 1-0 are for temp1, bits 3-2 for temp2 and bits 5-4 for -temp3, although it is possible that only the most significant bit matters -each time. So far, values other than 0 always broke the readings. - -PWM registers seem to be split in two parts: bit 7 is a mode selector, -while the other bits seem to define a value or threshold. - -When bit 7 is clear, bits 6-0 seem to hold a threshold value. If the value -is below a given limit, the fan runs at low speed. If the value is above -the limit, the fan runs at full speed. We have no clue as to what the limit -represents. Note that there seem to be some inertia in this mode, speed -changes may need some time to trigger. Also, an hysteresis mechanism is -suspected since walking through all the values increasingly and then -decreasingly led to slightly different limits. - -When bit 7 is set, bits 3-0 seem to hold a threshold value, while bits 6-4 -would not be significant. If the value is below a given limit, the fan runs -at full speed, while if it is above the limit it runs at low speed (so this -is the contrary of the other mode, in a way). Here again, we don't know -what the limit is supposed to represent. - -One remarkable thing is that the fans would only have two or three -different speeds (transitional states left apart), not a whole range as -you usually get with PWM. - -As a conclusion, you can write 0x00 or 0x8F to the PWM registers to make -fans run at low speed, and 0x7F or 0x80 to make them run at full speed. - -Please contact us if you can figure out how it is supposed to work. As -long as we don't know more, the w83781d driver doesn't handle PWM on -AS99127F chips at all. - -Additional info about PWM on the AS99127F rev.1 by Hector Martin: - -I've been fiddling around with the (in)famous 0x59 register and -found out the following values do work as a form of coarse pwm: - -0x80 - seems to turn fans off after some time(1-2 minutes)... might be -some form of auto-fan-control based on temp? hmm (Qfan? this mobo is an -old ASUS, it isn't marketed as Qfan. Maybe some beta pre-attemp at Qfan -that was dropped at the BIOS) -0x81 - off -0x82 - slightly "on-ner" than off, but my fans do not get to move. I can -hear the high-pitched PWM sound that motors give off at too-low-pwm. -0x83 - now they do move. Estimate about 70% speed or so. -0x84-0x8f - full on - -Changing the high nibble doesn't seem to do much except the high bit -(0x80) must be set for PWM to work, else the current pwm doesn't seem to -change. - -My mobo is an ASUS A7V266-E. This behavior is similar to what I got -with speedfan under Windows, where 0-15% would be off, 15-2x% (can't -remember the exact value) would be 70% and higher would be full on. |