diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 124 |
1 files changed, 102 insertions, 22 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 33121d6c827c..8fd5aa40585f 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -34,6 +34,7 @@ parameter is applicable: ALSA ALSA sound support is enabled. APIC APIC support is enabled. APM Advanced Power Management support is enabled. + AVR32 AVR32 architecture is enabled. AX25 Appropriate AX.25 support is enabled. BLACKFIN Blackfin architecture is enabled. DRM Direct Rendering Management support is enabled. @@ -167,6 +168,11 @@ and is between 256 and 4096 characters. It is defined in the file acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA Format: <irq>,<irq>... + acpi_new_pts_ordering [HW,ACPI] + Enforce the ACPI 2.0 ordering of the _PTS control + method wrt putting devices into low power states + default: pre ACPI 2.0 ordering of _PTS + acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS @@ -369,7 +375,8 @@ and is between 256 and 4096 characters. It is defined in the file configured. Potentially dangerous and should only be used if you are entirely sure of the consequences. - chandev= [HW,NET] Generic channel device initialisation + ccw_timeout_log [S390] + See Documentation/s390/CommonIO for details. checkreqprot [SELINUX] Set initial checkreqprot flag value. Format: { "0" | "1" } @@ -381,6 +388,12 @@ and is between 256 and 4096 characters. It is defined in the file Value can be changed at runtime via /selinux/checkreqprot. + cio_ignore= [S390] + See Documentation/s390/CommonIO for details. + + cio_msg= [S390] + See Documentation/s390/CommonIO for details. + clock= [BUGS=X86-32, HW] gettimeofday clocksource override. [Deprecated] Forces specified clocksource (if available) to be used @@ -408,8 +421,21 @@ and is between 256 and 4096 characters. It is defined in the file [SPARC64] tick [X86-64] hpet,tsc - code_bytes [IA32] How many bytes of object code to print in an - oops report. + clearcpuid=BITNUM [X86] + Disable CPUID feature X for the kernel. See + include/asm-x86/cpufeature.h for the valid bit numbers. + Note the Linux specific bits are not necessarily + stable over kernel options, but the vendor specific + ones should be. + Also note that user programs calling CPUID directly + or using the feature without checking anything + will still see it. This just prevents it from + being used by the kernel or shown in /proc/cpuinfo. + Also note the kernel might malfunction if you disable + some critical bits. + + code_bytes [IA32/X86_64] How many bytes of object code to print + in an oops report. Range: 0 - 8192 Default: 64 @@ -523,33 +549,34 @@ and is between 256 and 4096 characters. It is defined in the file 1 will print _a lot_ more information - normally only useful to kernel developers. - decnet= [HW,NET] + decnet.addr= [HW,NET] Format: <area>[,<node>] See also Documentation/networking/decnet.txt. - default_blu= [VT] + vt.default_blu= [VT] Format: <blue0>,<blue1>,<blue2>,...,<blue15> Change the default blue palette of the console. This is a 16-member array composed of values ranging from 0-255. - default_grn= [VT] + vt.default_grn= [VT] Format: <green0>,<green1>,<green2>,...,<green15> Change the default green palette of the console. This is a 16-member array composed of values ranging from 0-255. - default_red= [VT] + vt.default_red= [VT] Format: <red0>,<red1>,<red2>,...,<red15> Change the default red palette of the console. This is a 16-member array composed of values ranging from 0-255. - default_utf8= [VT] + vt.default_utf8= + [VT] Format=<0|1> Set system-wide default UTF-8 mode for all tty's. - Default is 0 and by setting to 1, it enables UTF-8 - mode for all newly opened or allocated terminals. + Default is 1, i.e. UTF-8 mode is enabled for all + newly opened terminals. dhash_entries= [KNL] Set number of hash buckets for dentry cache. @@ -561,6 +588,12 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/digiepca.txt. + disable_mtrr_trim [X86, Intel and AMD only] + By default the kernel will trim any uncacheable + memory out of your available memory pool based on + MTRR settings. This parameter disables that behavior, + possibly causing your machine to run very slowly. + dmasound= [HW,OSS] Sound subsystem buffers dscc4.setup= [NET] @@ -651,6 +684,10 @@ and is between 256 and 4096 characters. It is defined in the file gamma= [HW,DRM] + gart_fix_e820= [X86_64] disable the fix e820 for K8 GART + Format: off | on + default: on + gdth= [HW,SCSI] See header of drivers/scsi/gdth.c. @@ -685,6 +722,7 @@ and is between 256 and 4096 characters. It is defined in the file See Documentation/isdn/README.HiSax. hugepages= [HW,X86-32,IA-64] Maximal number of HugeTLB pages. + hugepagesz= [HW,IA-64,PPC] The size of the HugeTLB pages. i8042.direct [HW] Put keyboard port into non-translated mode i8042.dumbkbd [HW] Pretend that controller can only read data from @@ -742,6 +780,9 @@ and is between 256 and 4096 characters. It is defined in the file loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same as idle=poll. + ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem + Claim all unknown PCI IDE storage controllers. + ignore_loglevel [KNL] Ignore loglevel setting - this will print /all/ kernel messages to the console. Useful for debugging. @@ -785,6 +826,16 @@ and is between 256 and 4096 characters. It is defined in the file for translation below 32 bit and if not available then look in the higher range. + io_delay= [X86-32,X86-64] I/O delay method + 0x80 + Standard port 0x80 based delay + 0xed + Alternate port 0xed based delay (needed on some systems) + udelay + Simple two microseconds delay + none + No delay + io7= [HW] IO7 for Marvel based alpha systems See comment before marvel_specify_io7 in arch/alpha/kernel/core_marvel.c. @@ -882,6 +933,14 @@ and is between 256 and 4096 characters. It is defined in the file lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer in C2 power state. + libata.dma= [LIBATA] DMA control + libata.dma=0 Disable all PATA and SATA DMA + libata.dma=1 PATA and SATA Disk DMA only + libata.dma=2 ATAPI (CDROM) DMA only + libata.dma=4 Compact Flash DMA only + Combinations also work, so libata.dma=3 enables DMA + for disks and CDROMs, but not CFs. + libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume when set. Format: <int> @@ -1042,6 +1101,11 @@ and is between 256 and 4096 characters. It is defined in the file Multi-Function General Purpose Timers on AMD Geode platforms. + mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when + the BIOS has incorrectly applied a workaround. TinyBIOS + version 0.98 is known to be affected, 0.99 fixes the + problem by letting the user disable the workaround. + mga= [HW,DRM] mousedev.tap_time= @@ -1114,6 +1178,10 @@ and is between 256 and 4096 characters. It is defined in the file of returning the full 64-bit number. The default is to return 64-bit inode numbers. + nmi_debug= [KNL,AVR32] Specify one or more actions to take + when a NMI is triggered. + Format: [state][,regs][,debounce][,die] + nmi_watchdog= [KNL,BUGS=X86-32] Debugging features for SMP kernels no387 [BUGS=X86-32] Tells the kernel to use the 387 maths @@ -1138,6 +1206,8 @@ and is between 256 and 4096 characters. It is defined in the file nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects. + noefi [X86-32,X86-64] Disable EFI runtime services support. + noexec [IA-64] noexec [X86-32,X86-64] @@ -1148,6 +1218,8 @@ and is between 256 and 4096 characters. It is defined in the file register save and restore. The kernel will only save legacy floating-point registers on task switch. + noclflush [BUGS=X86] Don't use the CLFLUSH instruction + nohlt [BUGS=ARM] no-hlt [BUGS=X86-32] Tells the kernel that the hlt @@ -1492,14 +1564,17 @@ and is between 256 and 4096 characters. It is defined in the file ramdisk_size= [RAM] Sizes of RAM disks in kilobytes See Documentation/ramdisk.txt. - rcu.blimit= [KNL,BOOT] Set maximum number of finished - RCU callbacks to process in one batch. + rcupdate.blimit= [KNL,BOOT] + Set maximum number of finished RCU callbacks to process + in one batch. - rcu.qhimark= [KNL,BOOT] Set threshold of queued + rcupdate.qhimark= [KNL,BOOT] + Set threshold of queued RCU callbacks over which batch limiting is disabled. - rcu.qlowmark= [KNL,BOOT] Set threshold of queued - RCU callbacks below which batch limiting is re-enabled. + rcupdate.qlowmark= [KNL,BOOT] + Set threshold of queued RCU callbacks below which + batch limiting is re-enabled. rdinit= [KNL] Format: <full_path> @@ -1584,7 +1659,13 @@ and is between 256 and 4096 characters. It is defined in the file Format: <vendor>:<model>:<flags> (flags are integer value) - scsi_logging= [SCSI] + scsi_logging_level= [SCSI] a bit mask of logging levels + See drivers/scsi/scsi_logging.h for bits. Also + settable via sysctl at dev.scsi.logging_level + (/proc/sys/dev/scsi/logging_level). + There is also a nice 'scsi_logging_level' script in the + S390-tools package, available for download at + http://www-128.ibm.com/developerworks/linux/linux390/s390-tools-1.5.4.html scsi_mod.scan= [SCSI] sync (default) scans SCSI busses as they are discovered. async scans them in kernel threads, @@ -1813,9 +1894,6 @@ and is between 256 and 4096 characters. It is defined in the file st= [HW,SCSI] SCSI tape parameters (buffers, etc.) See Documentation/scsi/st.txt. - st0x= [HW,SCSI] - See header of drivers/scsi/seagate.c. - sti= [PARISC,HW] Format: <num> Set the STI (builtin display/keyboard on the HP-PARISC @@ -1900,9 +1978,6 @@ and is between 256 and 4096 characters. It is defined in the file tipar.delay= [HW,PPT] Set inter-bit delay in microseconds (default 10). - tmc8xx= [HW,SCSI] - See header of drivers/scsi/seagate.c. - tmscsim= [HW,SCSI] See comment before function dc390_setup() in drivers/scsi/tmscsim.c. @@ -1951,6 +2026,11 @@ and is between 256 and 4096 characters. It is defined in the file vdso=1: enable VDSO (default) vdso=0: disable VDSO mapping + vdso32= [X86-32,X86-64] + vdso32=2: enable compat VDSO (default with COMPAT_VDSO) + vdso32=1: enable 32-bit VDSO (default) + vdso32=0: disable 32-bit VDSO mapping + vector= [IA-64,SMP] vector=percpu: enable percpu vector domain |