diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 33 |
1 files changed, 23 insertions, 10 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 8c666d80f0e7..839b21b0699a 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -54,6 +54,7 @@ parameter is applicable: IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. + IPV6 IPv6 support is enabled. ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. @@ -199,10 +200,6 @@ and is between 256 and 4096 characters. It is defined in the file acpi_display_output=video See above. - acpi_early_pdc_eval [HW,ACPI] Evaluate processor _PDC methods - early. Needed on some platforms to properly - initialize the EC. - acpi_irq_balance [HW,ACPI] ACPI will balance active IRQs default in APIC mode @@ -323,11 +320,6 @@ and is between 256 and 4096 characters. It is defined in the file amd_iommu= [HW,X86-84] Pass parameters to the AMD IOMMU driver in the system. Possible values are: - isolate - enable device isolation (each device, as far - as possible, will get its own protection - domain) [default] - share - put every device behind one IOMMU into the - same protection domain fullflush - enable flushing of IO/TLB entries when they are unmapped. Otherwise they are flushed before they will be reused, which @@ -356,6 +348,9 @@ and is between 256 and 4096 characters. It is defined in the file Change the amount of debugging information output when initialising the APIC and IO-APIC components. + autoconf= [IPV6] + See Documentation/networking/ipv6.txt. + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller Limit apic dumping. The parameter defines the maximal number of local apics being dumped. Also it is possible @@ -638,6 +633,12 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/serial/digiepca.txt. + disable= [IPV6] + See Documentation/networking/ipv6.txt. + + disable_ipv6= [IPV6] + See Documentation/networking/ipv6.txt. + disable_mtrr_cleanup [X86] The kernel tries to adjust MTRR layout from continuous to discrete, to make X server driver able to add WB @@ -1193,7 +1194,7 @@ and is between 256 and 4096 characters. It is defined in the file libata.force= [LIBATA] Force configurations. The format is comma separated list of "[ID:]VAL" where ID is - PORT[:DEVICE]. PORT and DEVICE are decimal numbers + PORT[.DEVICE]. PORT and DEVICE are decimal numbers matching port, link or device. Basically, it matches the ATA ID string printed on console by libata. If the whole ID part is omitted, the last PORT and DEVICE @@ -1784,6 +1785,12 @@ and is between 256 and 4096 characters. It is defined in the file purges which is reported from either PAL_VM_SUMMARY or SAL PALO. + nr_cpus= [SMP] Maximum number of processors that an SMP kernel + could support. nr_cpus=n : n >= 1 limits the kernel to + supporting 'n' processors. Later in runtime you can not + use hotplug cpu feature to put more cpu back to online. + just like you compile the kernel NR_CPUS=n + nr_uarts= [SERIAL] maximum number of UARTs to be registered. numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. @@ -2818,6 +2825,12 @@ and is between 256 and 4096 characters. It is defined in the file default x2apic cluster mode on platforms supporting x2apic. + x86_mrst_timer= [X86-32,APBT] + Choose timer option for x86 Moorestown MID platform. + Two valid options are apbt timer only and lapic timer + plus one apbt timer for broadcast timer. + x86_mrst_timer=apbt_only | lapic_and_apbt + xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks. xd_geo= See header of drivers/block/xd.c. |