diff options
Diffstat (limited to 'Documentation/networking/bonding.txt')
| -rw-r--r-- | Documentation/networking/bonding.txt | 112 |
1 files changed, 81 insertions, 31 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index a0cda062bc33..688dfe1e6b70 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -289,35 +289,73 @@ downdelay fail_over_mac Specifies whether active-backup mode should set all slaves to - the same MAC address (the traditional behavior), or, when - enabled, change the bond's MAC address when changing the - active interface (i.e., fail over the MAC address itself). - - Fail over MAC is useful for devices that cannot ever alter - their MAC address, or for devices that refuse incoming - broadcasts with their own source MAC (which interferes with - the ARP monitor). - - The down side of fail over MAC is that every device on the - network must be updated via gratuitous ARP, vs. just updating - a switch or set of switches (which often takes place for any - traffic, not just ARP traffic, if the switch snoops incoming - traffic to update its tables) for the traditional method. If - the gratuitous ARP is lost, communication may be disrupted. - - When fail over MAC is used in conjuction with the mii monitor, - devices which assert link up prior to being able to actually - transmit and receive are particularly susecptible to loss of - the gratuitous ARP, and an appropriate updelay setting may be - required. - - A value of 0 disables fail over MAC, and is the default. A - value of 1 enables fail over MAC. This option is enabled - automatically if the first slave added cannot change its MAC - address. This option may be modified via sysfs only when no - slaves are present in the bond. - - This option was added in bonding version 3.2.0. + the same MAC address at enslavement (the traditional + behavior), or, when enabled, perform special handling of the + bond's MAC address in accordance with the selected policy. + + Possible values are: + + none or 0 + + This setting disables fail_over_mac, and causes + bonding to set all slaves of an active-backup bond to + the same MAC address at enslavement time. This is the + default. + + active or 1 + + The "active" fail_over_mac policy indicates that the + MAC address of the bond should always be the MAC + address of the currently active slave. The MAC + address of the slaves is not changed; instead, the MAC + address of the bond changes during a failover. + + This policy is useful for devices that cannot ever + alter their MAC address, or for devices that refuse + incoming broadcasts with their own source MAC (which + interferes with the ARP monitor). + + The down side of this policy is that every device on + the network must be updated via gratuitous ARP, + vs. just updating a switch or set of switches (which + often takes place for any traffic, not just ARP + traffic, if the switch snoops incoming traffic to + update its tables) for the traditional method. If the + gratuitous ARP is lost, communication may be + disrupted. + + When this policy is used in conjuction with the mii + monitor, devices which assert link up prior to being + able to actually transmit and receive are particularly + susecptible to loss of the gratuitous ARP, and an + appropriate updelay setting may be required. + + follow or 2 + + The "follow" fail_over_mac policy causes the MAC + address of the bond to be selected normally (normally + the MAC address of the first slave added to the bond). + However, the second and subsequent slaves are not set + to this MAC address while they are in a backup role; a + slave is programmed with the bond's MAC address at + failover time (and the formerly active slave receives + the newly active slave's MAC address). + + This policy is useful for multiport devices that + either become confused or incur a performance penalty + when multiple ports are programmed with the same MAC + address. + + + The default policy is none, unless the first slave cannot + change its MAC address, in which case the active policy is + selected by default. + + This option may be modified via sysfs only when no slaves are + present in the bond. + + This option was added in bonding version 3.2.0. The "follow" + policy was added in bonding version 3.3.0. lacp_rate @@ -338,7 +376,8 @@ max_bonds Specifies the number of bonding devices to create for this instance of the bonding driver. E.g., if max_bonds is 3, and the bonding driver is not already loaded, then bond0, bond1 - and bond2 will be created. The default value is 1. + and bond2 will be created. The default value is 1. Specifying + a value of 0 will load bonding, but will not create any devices. miimon @@ -501,6 +540,17 @@ mode swapped with the new curr_active_slave that was chosen. +num_grat_arp + + Specifies the number of gratuitous ARPs to be issued after a + failover event. One gratuitous ARP is issued immediately after + the failover, subsequent ARPs are sent at a rate of one per link + monitor interval (arp_interval or miimon, whichever is active). + + The valid range is 0 - 255; the default value is 1. This option + affects only the active-backup mode. This option was added for + bonding version 3.3.0. + primary A string (eth0, eth2, etc) specifying which slave is the @@ -581,7 +631,7 @@ xmit_hash_policy in environments where a layer3 gateway device is required to reach most destinations. - This algorithm is 802.3ad complient. + This algorithm is 802.3ad compliant. layer3+4 |