diff options
Diffstat (limited to 'Documentation/networking/comx.txt')
| -rw-r--r-- | Documentation/networking/comx.txt | 248 |
1 files changed, 0 insertions, 248 deletions
diff --git a/Documentation/networking/comx.txt b/Documentation/networking/comx.txt deleted file mode 100644 index d1526eba2645..000000000000 --- a/Documentation/networking/comx.txt +++ /dev/null @@ -1,248 +0,0 @@ - - COMX drivers for the 2.2 kernel - -Originally written by: Tivadar Szemethy, <tiv@itc.hu> -Currently maintained by: Gergely Madarasz <gorgo@itc.hu> - -Last change: 21/06/1999. - -INTRODUCTION - -This document describes the software drivers and their use for the -COMX line of synchronous serial adapters for Linux version 2.2.0 and -above. -The cards are produced and sold by ITC-Pro Ltd. Budapest, Hungary -For further info contact <info@itc.hu> -or http://www.itc.hu (mostly in Hungarian). -The firmware files and software are available from ftp://ftp.itc.hu - -Currently, the drivers support the following cards and protocols: - -COMX (2x64 kbps intelligent board) -CMX (1x256 + 1x128 kbps intelligent board) -HiCOMX (2x2Mbps intelligent board) -LoCOMX (1x512 kbps passive board) -MixCOM (1x512 or 2x512kbps passive board with a hardware watchdog an - optional BRI interface and optional flashROM (1-32M)) -SliceCOM (1x2Mbps channelized E1 board) -PciCOM (X21) - -At the moment of writing this document, the (Cisco)-HDLC, LAPB, SyncPPP and -Frame Relay (DTE, rfc1294 IP encapsulation with partially implemented Q933a -LMI) protocols are available as link-level protocol. -X.25 support is being worked on. - -USAGE - -Load the comx.o module and the hardware-specific and protocol-specific -modules you'll need into the running kernel using the insmod utility. -This creates the /proc/comx directory. -See the example scripts in the 'etc' directory. - -/proc INTERFACE INTRO - -The COMX driver set has a new type of user interface based on the /proc -filesystem which eliminates the need for external user-land software doing -IOCTL calls. -Each network interface or device (i.e. those ones you configure with 'ifconfig' -and 'route' etc.) has a corresponding directory under /proc/comx. You can -dynamically create a new interface by saying 'mkdir /proc/comx/comx0' (or you -can name it whatever you want up to 8 characters long, comx[n] is just a -convention). -Generally the files contained in these directories are text files, which can -be viewed by 'cat filename' and you can write a string to such a file by -saying 'echo _string_ >filename'. This is very similar to the sysctl interface. -Don't use a text editor to edit these files, always use 'echo' (or 'cat' -where appropriate). -When you've created the comx[n] directory, two files are created automagically -in it: 'boardtype' and 'protocol'. You have to fill in these files correctly -for your board and protocol you intend to use (see the board and protocol -descriptions in this file below or the example scripts in the 'etc' directory). -After filling in these files, other files will appear in the directory for -setting the various hardware- and protocol-related informations (for example -irq and io addresses, keepalive values etc.) These files are set to default -values upon creation, so you don't necessarily have to change all of them. - -When you're ready with filling in the files in the comx[n] directory, you can -configure the corresponding network interface with the standard network -configuration utilities. If you're unable to bring the interfaces up, look up -the various kernel log files on your system, and consult the messages for -a probable reason. - -EXAMPLE - -To create the interface 'comx0' which is the first channel of a COMX card: - -insmod comx -# insmod comx-hw-comx ; insmod comx-proto-ppp (these are usually -autoloaded if you use the kernel module loader) - -mkdir /proc/comx/comx0 -echo comx >/proc/comx/comx0/boardtype -echo 0x360 >/proc/comx/comx0/io <- jumper-selectable I/O port -echo 0x0a >/proc/comx/comx0/irq <- jumper-selectable IRQ line -echo 0xd000 >/proc/comx/comx0/memaddr <- software-configurable memory - address. COMX uses 64 KB, and this - can be: 0xa000, 0xb000, 0xc000, - 0xd000, 0xe000. Avoid conflicts - with other hardware. -cat </etc/siol1.rom >/proc/comx/comx0/firmware <- the firmware for the card -echo HDLC >/proc/comx/comx0/protocol <- the data-link protocol -echo 10 >/proc/comx/comx0/keepalive <- the keepalive for the protocol -ifconfig comx0 1.2.3.4 pointopoint 5.6.7.8 netmask 255.255.255.255 <- - finally configure it with ifconfig -Check its status: -cat /proc/comx/comx0/status - -If you want to use the second channel of this board: - -mkdir /proc/comx/comx1 -echo comx >/proc/comx/comx1/boardtype -echo 0x360 >/proc/comx/comx1/io -echo 10 >/proc/comx/comx1/irq -echo 0xd000 >/proc/comx/comx1/memaddr -echo 1 >/proc/comx/comx1/channel <- channels are numbered - as 0 (default) and 1 - -Now, check if the driver recognized that you're going to use the other -channel of the same adapter: - -cat /proc/comx/comx0/twin -comx1 -cat /proc/comx/comx1/twin -comx0 - -You don't have to load the firmware twice, if you use both channels of -an adapter, just write it into the channel 0's /proc firmware file. - -Default values: io 0x360 for COMX, 0x320 (HICOMX), irq 10, memaddr 0xd0000 - -THE LOCOMX HARDWARE DRIVER - -The LoCOMX driver doesn't require firmware, and it doesn't use memory either, -but it uses DMA channels 1 and 3. You can set the clock rate (if enabled by -jumpers on the board) by writing the kbps value into the file named 'clock'. -Set it to 'external' (it is the default) if you have external clock source. - -(Note: currently the LoCOMX driver does not support the internal clock) - -THE COMX, CMX AND HICOMX DRIVERS - -On the HICOMX, COMX and CMX, you have to load the firmware (it is different for -the three cards!). All these adapters can share the same memory -address (we usually use 0xd0000). On the CMX you can set the internal -clock rate (if enabled by jumpers on the small adapter boards) by writing -the kbps value into the 'clock' file. You have to do this before initializing -the card. If you use both HICOMX and CMX/COMX cards, initialize the HICOMX -first. The I/O address of the HICOMX board is not configurable by any -method available to the user: it is hardwired to 0x320, and if you have to -change it, consult ITC-Pro Ltd. - -THE MIXCOM DRIVER - -The MixCOM board doesn't require firmware, the driver communicates with -it through I/O ports. You can have three of these cards in one machine. - -THE SLICECOM DRIVER - -The SliceCOM board doesn't require firmware. You can have 4 of these cards -in one machine. The driver doesn't (yet) support shared interrupts, so -you will need a separate IRQ line for every board. -Read Documentation/networking/slicecom.txt for help on configuring -this adapter. - -THE HDLC/PPP LINE PROTOCOL DRIVER - -The HDLC/SyncPPP line protocol driver uses the kernel's built-in syncppp -driver (syncppp.o). You don't have to manually select syncppp.o when building -the kernel, the dependencies compile it in automatically. - - - - -EXAMPLE -(setting up hw parameters, see above) - -# using HDLC: -echo hdlc >/proc/comx/comx0/protocol -echo 10 >/proc/comx/comx0/keepalive <- not necessary, 10 is the default -ifconfig comx0 1.2.3.4 pointopoint 5.6.7.8 netmask 255.255.255.255 - -(setting up hw parameters, see above) - -# using PPP: -echo ppp >/proc/comx/comx0/protocol -ifconfig comx0 up -ifconfig comx0 1.2.3.4 pointopoint 5.6.7.8 netmask 255.255.255.255 - - -THE LAPB LINE PROTOCOL DRIVER - -For this, you'll need to configure LAPB support (See 'LAPB Data Link Driver' in -'Network options' section) into your kernel (thanks to Jonathan Naylor for his -excellent implementation). -comx-proto-lapb.o provides the following files in the appropriate directory -(the default values in parens): t1 (5), t2 (1), n2 (20), mode (DTE, STD) and -window (7). Agree with the administrator of your peer router on these -settings (most people use defaults, but you have to know if you are DTE or -DCE). - -EXAMPLE - -(setting up hw parameters, see above) -echo lapb >/proc/comx/comx0/protocol -echo dce >/proc/comx/comx0/mode <- DCE interface in this example -ifconfig comx0 1.2.3.4 pointopoint 5.6.7.8 netmask 255.255.255.255 - - -THE FRAME RELAY PROTOCOL DRIVER - -You DON'T need any other frame relay related modules from the kernel to use -COMX-Frame Relay. This protocol is a bit more complicated than the others, -because it allows to use 'subinterfaces' or DLCIs within one physical device. -First you have to create the 'master' device (the actual physical interface) -as you would do for other protocols. Specify 'frad' as protocol type. -Now you can bring this interface up by saying 'ifconfig comx0 up' (or whatever -you've named the interface). Do not assign any IP address to this interface -and do not set any routes through it. -Then, set up your DLCIs the following way: create a comx interface for each -DLCI you intend to use (with mkdir), and write 'dlci' to the 'boardtype' file, -and 'ietf-ip' to the 'protocol' file. Currently, the only supported -encapsulation type is this (also called as RFC1294/1490 IP encapsulation). -Write the DLCI number to the 'dlci' file, and write the name of the physical -COMX device to the file called 'master'. -Now you can assign an IP address to this interface and set routes using it. -See the example file for further info and example config script. -Notes: this driver implements a DTE interface with partially implemented -Q933a LMI. -You can find an extensively commented example in the 'etc' directory. - -FURTHER /proc FILES - -boardtype: -Type of the hardware. Valid values are: - 'comx', 'hicomx', 'locomx', 'cmx', 'slicecom'. - -protocol: -Data-link protocol on this channel. Can be: HDLC, LAPB, PPP, FRAD - -status: -You can read the channel's actual status from the 'status' file, for example -'cat /proc/comx/comx3/status'. - -lineup_delay: -Interpreted in seconds (default is 1). Used to avoid line jitter: the system -will consider the line status 'UP' only if it is up for at least this number -of seconds. - -debug: -You can set various debug options through this file. Valid options are: -'comx_events', 'comx_tx', 'comx_rx', 'hw_events', 'hw_tx', 'hw_rx'. -You can enable a debug options by writing its name prepended by a '+' into -the debug file, for example 'echo +comx_rx >comx0/debug'. -Disabling an option happens similarly, use the '-' prefix -(e.g. 'echo -hw_rx >debug'). -Debug results can be read from the debug file, for example: -tail -f /proc/comx/comx2/debug - - |