diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/batman-adv.txt | 54 | ||||
| -rw-r--r-- | Documentation/networking/bonding.txt | 66 | ||||
| -rw-r--r-- | Documentation/networking/netdevices.txt | 10 |
3 files changed, 45 insertions, 85 deletions
diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt index c1d82047a4b1..89490beb3c0b 100644 --- a/Documentation/networking/batman-adv.txt +++ b/Documentation/networking/batman-adv.txt @@ -69,8 +69,7 @@ folder: # aggregated_ogms gw_bandwidth log_level # ap_isolation gw_mode orig_interval # bonding gw_sel_class routing_algo -# bridge_loop_avoidance hop_penalty vis_mode -# fragmentation +# bridge_loop_avoidance hop_penalty fragmentation There is a special folder for debugging information: @@ -78,7 +77,7 @@ There is a special folder for debugging information: # ls /sys/kernel/debug/batman_adv/bat0/ # bla_backbone_table log transtable_global # bla_claim_table originators transtable_local -# gateways socket vis_data +# gateways socket Some of the files contain all sort of status information regard- ing the mesh network. For example, you can view the table of @@ -127,51 +126,6 @@ ously assigned to interfaces now used by batman advanced, e.g. # ifconfig eth0 0.0.0.0 -VISUALIZATION -------------- - -If you want topology visualization, at least one mesh node must -be configured as VIS-server: - -# echo "server" > /sys/class/net/bat0/mesh/vis_mode - -Each node is either configured as "server" or as "client" (de- -fault: "client"). Clients send their topology data to the server -next to them, and server synchronize with other servers. If there -is no server configured (default) within the mesh, no topology -information will be transmitted. With these "synchronizing -servers", there can be 1 or more vis servers sharing the same (or -at least very similar) data. - -When configured as server, you can get a topology snapshot of -your mesh: - -# cat /sys/kernel/debug/batman_adv/bat0/vis_data - -This raw output is intended to be easily parsable and convertable -with other tools. Have a look at the batctl README if you want a -vis output in dot or json format for instance and how those out- -puts could then be visualised in an image. - -The raw format consists of comma separated values per entry where -each entry is giving information about a certain source inter- -face. Each entry can/has to have the following values: --> "mac" - mac address of an originator's source interface - (each line begins with it) --> "TQ mac value" - src mac's link quality towards mac address - of a neighbor originator's interface which - is being used for routing --> "TT mac" - TT announced by source mac --> "PRIMARY" - this is a primary interface --> "SEC mac" - secondary mac address of source - (requires preceding PRIMARY) - -The TQ value has a range from 4 to 255 with 255 being the best. -The TT entries are showing which hosts are connected to the mesh -via bat0 or being bridged into the mesh network. The PRIMARY/SEC -values are only applied on primary interfaces - - LOGGING/DEBUGGING ----------------- @@ -245,5 +199,5 @@ Mailing-list: b.a.t.m.a.n@open-mesh.org (optional subscription You can also contact the Authors: -Marek Lindner <lindner_marek@yahoo.de> -Simon Wunderlich <siwu@hrz.tu-chemnitz.de> +Marek Lindner <mareklindner@neomailbox.ch> +Simon Wunderlich <sw@simonwunderlich.de> diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 9b28e714831a..3856ed2c45a9 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -743,21 +743,16 @@ xmit_hash_policy protocol information to generate the hash. Uses XOR of hardware MAC addresses and IP addresses to - generate the hash. The IPv4 formula is + generate the hash. The formula is - (((source IP XOR dest IP) AND 0xffff) XOR - ( source MAC XOR destination MAC )) - modulo slave count + hash = source MAC XOR destination MAC + hash = hash XOR source IP XOR destination IP + hash = hash XOR (hash RSHIFT 16) + hash = hash XOR (hash RSHIFT 8) + And then hash is reduced modulo slave count. - The IPv6 formula is - - hash = (source ip quad 2 XOR dest IP quad 2) XOR - (source ip quad 3 XOR dest IP quad 3) XOR - (source ip quad 4 XOR dest IP quad 4) - - (((hash >> 24) XOR (hash >> 16) XOR (hash >> 8) XOR hash) - XOR (source MAC XOR destination MAC)) - modulo slave count + If the protocol is IPv6 then the source and destination + addresses are first hashed using ipv6_addr_hash. This algorithm will place all traffic to a particular network peer on the same slave. For non-IP traffic, @@ -779,21 +774,16 @@ xmit_hash_policy slaves, although a single connection will not span multiple slaves. - The formula for unfragmented IPv4 TCP and UDP packets is - - ((source port XOR dest port) XOR - ((source IP XOR dest IP) AND 0xffff) - modulo slave count + The formula for unfragmented TCP and UDP packets is - The formula for unfragmented IPv6 TCP and UDP packets is + hash = source port, destination port (as in the header) + hash = hash XOR source IP XOR destination IP + hash = hash XOR (hash RSHIFT 16) + hash = hash XOR (hash RSHIFT 8) + And then hash is reduced modulo slave count. - hash = (source port XOR dest port) XOR - ((source ip quad 2 XOR dest IP quad 2) XOR - (source ip quad 3 XOR dest IP quad 3) XOR - (source ip quad 4 XOR dest IP quad 4)) - - ((hash >> 24) XOR (hash >> 16) XOR (hash >> 8) XOR hash) - modulo slave count + If the protocol is IPv6 then the source and destination + addresses are first hashed using ipv6_addr_hash. For fragmented TCP or UDP packets and all other IPv4 and IPv6 protocol traffic, the source and destination port @@ -801,10 +791,6 @@ xmit_hash_policy formula is the same as for the layer2 transmit hash policy. - The IPv4 policy is intended to mimic the behavior of - certain switches, notably Cisco switches with PFC2 as - well as some Foundry and IBM products. - This algorithm is not fully 802.3ad compliant. A single TCP or UDP conversation containing both fragmented and unfragmented packets will see packets @@ -815,6 +801,26 @@ xmit_hash_policy conversations. Other implementations of 802.3ad may or may not tolerate this noncompliance. + encap2+3 + + This policy uses the same formula as layer2+3 but it + relies on skb_flow_dissect to obtain the header fields + which might result in the use of inner headers if an + encapsulation protocol is used. For example this will + improve the performance for tunnel users because the + packets will be distributed according to the encapsulated + flows. + + encap3+4 + + This policy uses the same formula as layer3+4 but it + relies on skb_flow_dissect to obtain the header fields + which might result in the use of inner headers if an + encapsulation protocol is used. For example this will + improve the performance for tunnel users because the + packets will be distributed according to the encapsulated + flows. + The default value is layer2. This option was added in bonding version 2.6.3. In earlier versions of bonding, this parameter does not exist, and the layer2 policy is the only policy. The diff --git a/Documentation/networking/netdevices.txt b/Documentation/networking/netdevices.txt index c7ecc7080494..0b1cf6b2a592 100644 --- a/Documentation/networking/netdevices.txt +++ b/Documentation/networking/netdevices.txt @@ -10,12 +10,12 @@ network devices. struct net_device allocation rules ================================== Network device structures need to persist even after module is unloaded and -must be allocated with kmalloc. If device has registered successfully, -it will be freed on last use by free_netdev. This is required to handle the -pathologic case cleanly (example: rmmod mydriver </sys/class/net/myeth/mtu ) +must be allocated with alloc_netdev_mqs() and friends. +If device has registered successfully, it will be freed on last use +by free_netdev(). This is required to handle the pathologic case cleanly +(example: rmmod mydriver </sys/class/net/myeth/mtu ) -There are routines in net_init.c to handle the common cases of -alloc_etherdev, alloc_netdev. These reserve extra space for driver +alloc_netdev_mqs()/alloc_netdev() reserve extra space for driver private data which gets freed when the network device is freed. If separately allocated data is attached to the network device (netdev_priv(dev)) then it is up to the module exit handler to free that. |