diff options
Diffstat (limited to 'Documentation/powerpc/booting-without-of.txt')
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 67 |
1 files changed, 12 insertions, 55 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index de4063cb4fdc..0ab0230cbcb0 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -41,25 +41,14 @@ Table of Contents VI - System-on-a-chip devices and nodes 1) Defining child nodes of an SOC 2) Representing devices without a current OF specification - a) MDIO IO device - b) Gianfar-compatible ethernet nodes - c) PHY nodes - d) Interrupt controllers - e) I2C - f) Freescale SOC USB controllers - g) Freescale SOC SEC Security Engines - h) Board Control and Status (BCSR) - i) Freescale QUICC Engine module (QE) - j) CFI or JEDEC memory-mapped NOR flash - k) Global Utilities Block - l) Freescale Communications Processor Module - m) Chipselect/Local Bus - n) 4xx/Axon EMAC ethernet nodes - o) Xilinx IP cores - p) Freescale Synchronous Serial Interface - q) USB EHCI controllers - r) MDIO on GPIOs - s) SPI busses + a) PHY nodes + b) Interrupt controllers + c) CFI or JEDEC memory-mapped NOR flash + d) 4xx/Axon EMAC ethernet nodes + e) Xilinx IP cores + f) USB EHCI controllers + g) MDIO on GPIOs + h) SPI busses VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -1830,41 +1819,7 @@ platforms are moved over to use the flattened-device-tree model. big-endian; }; - r) Freescale Display Interface Unit - - The Freescale DIU is a LCD controller, with proper hardware, it can also - drive DVI monitors. - - Required properties: - - compatible : should be "fsl-diu". - - reg : should contain at least address and length of the DIU register - set. - - Interrupts : one DIU interrupt should be describe here. - - Example (MPC8610HPCD) - display@2c000 { - compatible = "fsl,diu"; - reg = <0x2c000 100>; - interrupts = <72 2>; - interrupt-parent = <&mpic>; - }; - - s) Freescale on board FPGA - - This is the memory-mapped registers for on board FPGA. - - Required properities: - - compatible : should be "fsl,fpga-pixis". - - reg : should contain the address and the lenght of the FPPGA register - set. - - Example (MPC8610HPCD) - board-control@e8000000 { - compatible = "fsl,fpga-pixis"; - reg = <0xe8000000 32>; - }; - - r) MDIO on GPIOs + g) MDIO on GPIOs Currently defined compatibles: - virtual,gpio-mdio @@ -1884,7 +1839,7 @@ platforms are moved over to use the flattened-device-tree model. &qe_pio_c 6>; }; - s) SPI (Serial Peripheral Interface) busses + h) SPI (Serial Peripheral Interface) busses SPI busses can be described with a node for the SPI master device and a set of child nodes for each SPI slave on the bus. For this @@ -1917,6 +1872,8 @@ platforms are moved over to use the flattened-device-tree model. inverse clock polarity (CPOL) mode - spi-cpha - (optional) Empty property indicating device requires shifted clock phase (CPHA) mode + - spi-cs-high - (optional) Empty property indicating device requires + chip select active high SPI example for an MPC5200 SPI bus: spi@f00 { |