diff options
Diffstat (limited to 'Documentation/powerpc')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/board.txt | 4 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpc5200.txt | 27 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/xilinx.txt | 11 |
3 files changed, 41 insertions, 1 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt index e8b5bc24d0ac..39e941515a36 100644 --- a/Documentation/powerpc/dts-bindings/fsl/board.txt +++ b/Documentation/powerpc/dts-bindings/fsl/board.txt @@ -20,12 +20,16 @@ Required properities: - compatible : should be "fsl,fpga-pixis". - reg : should contain the address and the length of the FPPGA register set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts : should specify event (wakeup) IRQ. Example (MPC8610HPCD): board-control@e8000000 { compatible = "fsl,fpga-pixis"; reg = <0xe8000000 32>; + interrupt-parent = <&mpic>; + interrupts = <8 8>; }; * Freescale BCSR GPIO banks diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt index 8447fd7090d0..5c6602dbfdc2 100644 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt +++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt @@ -103,7 +103,22 @@ fsl,mpc5200-gpt nodes --------------------- On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board design supports the internal wdt, then the device node for GPT0 should -include the empty property 'fsl,has-wdt'. +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. An mpc5200-gpt can be used as a single line GPIO controller. To do so, add the following properties to the gpt node: @@ -178,3 +193,13 @@ External interrupts: external irq3: interrupts = <1 3 n>; 'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properites, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source- a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt index 80339fe4300b..ea68046bb9cb 100644 --- a/Documentation/powerpc/dts-bindings/xilinx.txt +++ b/Documentation/powerpc/dts-bindings/xilinx.txt @@ -292,4 +292,15 @@ - reg-offset : A value of 3 is required - reg-shift : A value of 2 is required + vii) Xilinx USB Host controller + + The Xilinx USB host controller is EHCI compatible but with a different + base address for the EHCI registers, and it is always a big-endian + USB Host controller. The hardware can be configured as high speed only, + or high speed/full speed hybrid. + + Required properties: + - xlnx,support-usb-fs: A value 0 means the core is built as high speed + only. A value 1 means the core also supports + full speed devices. |