diff options
Diffstat (limited to 'Documentation/voyager.txt')
| -rw-r--r-- | Documentation/voyager.txt | 95 |
1 files changed, 0 insertions, 95 deletions
diff --git a/Documentation/voyager.txt b/Documentation/voyager.txt deleted file mode 100644 index 2749af552cdf..000000000000 --- a/Documentation/voyager.txt +++ /dev/null @@ -1,95 +0,0 @@ -Running Linux on the Voyager Architecture -========================================= - -For full details and current project status, see - -http://www.hansenpartnership.com/voyager - -The voyager architecture was designed by NCR in the mid 80s to be a -fully SMP capable RAS computing architecture built around intel's 486 -chip set. The voyager came in three levels of architectural -sophistication: 3,4 and 5 --- 1 and 2 never made it out of prototype. -The linux patches support only the Level 5 voyager architecture (any -machine class 3435 and above). - -The Voyager Architecture ------------------------- - -Voyager machines consist of a Baseboard with a 386 diagnostic -processor, a Power Supply Interface (PSI) a Primary and possibly -Secondary Microchannel bus and between 2 and 20 voyager slots. The -voyager slots can be populated with memory and cpu cards (up to 4GB -memory and from 1 486 to 32 Pentium Pro processors). Internally, the -voyager has a dual arbitrated system bus and a configuration and test -bus (CAT). The voyager bus speed is 40MHz. Therefore (since all -voyager cards are dual ported for each system bus) the maximum -transfer rate is 320Mb/s but only if you have your slot configuration -tuned (only memory cards can communicate with both busses at once, CPU -cards utilise them one at a time). - -Voyager SMP ------------ - -Since voyager was the first intel based SMP system, it is slightly -more primitive than the Intel IO-APIC approach to SMP. Voyager allows -arbitrary interrupt routing (including processor affinity routing) of -all 16 PC type interrupts. However it does this by using a modified -5259 master/slave chip set instead of an APIC bus. Additionally, -voyager supports Cross Processor Interrupts (CPI) equivalent to the -APIC IPIs. There are two routed voyager interrupt lines provided to -each slot. - -Processor Cards ---------------- - -These come in single, dyadic and quad configurations (the quads are -problematic--see later). The maximum configuration is 8 quad cards -for 32 way SMP. - -Quad Processors ---------------- - -Because voyager only supplies two interrupt lines to each Processor -card, the Quad processors have to be configured (and Bootstrapped) in -as a pair of Master/Slave processors. - -In fact, most Quad cards only accept one VIC interrupt line, so they -have one interrupt handling processor (called the VIC extended -processor) and three non-interrupt handling processors. - -Current Status --------------- - -The System will boot on Mono, Dyad and Quad cards. There was -originally a Quad boot problem which has been fixed by proper gdt -alignment in the initial boot loader. If you still cannot get your -voyager system to boot, email me at: - -<J.E.J.Bottomley@HansenPartnership.com> - - -The Quad cards now support using the separate Quad CPI vectors instead -of going through the VIC mailbox system. - -The Level 4 architecture (3430 and 3360 Machines) should also work -fine. - -Dump Switch ------------ - -The voyager dump switch sends out a broadcast NMI which the voyager -code intercepts and does a task dump. - -Power Switch ------------- - -The front panel power switch is intercepted by the kernel and should -cause a system shutdown and power off. - -A Note About Mixed CPU Systems ------------------------------- - -Linux isn't designed to handle mixed CPU systems very well. In order -to get everything going you *must* make sure that your lowest -capability CPU is used for booting. Also, mixing CPU classes -(e.g. 486 and 586) is really not going to work very well at all. |