diff options
Diffstat (limited to 'Documentation/x86/x86_64')
| -rw-r--r-- | Documentation/x86/x86_64/00-INDEX | 16 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/boot-options.txt | 314 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/cpu-hotplug-spec | 21 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/fake-numa-for-cpusets | 66 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/kernel-stacks | 99 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/machinecheck | 77 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/mm.txt | 28 | ||||
| -rw-r--r-- | Documentation/x86/x86_64/uefi.txt | 38 |
8 files changed, 659 insertions, 0 deletions
diff --git a/Documentation/x86/x86_64/00-INDEX b/Documentation/x86/x86_64/00-INDEX new file mode 100644 index 000000000000..92fc20ab5f0e --- /dev/null +++ b/Documentation/x86/x86_64/00-INDEX @@ -0,0 +1,16 @@ +00-INDEX + - This file +boot-options.txt + - AMD64-specific boot options. +cpu-hotplug-spec + - Firmware support for CPU hotplug under Linux/x86-64 +fake-numa-for-cpusets + - Using numa=fake and CPUSets for Resource Management +kernel-stacks + - Context-specific per-processor interrupt stacks. +machinecheck + - Configurable sysfs parameters for the x86-64 machine check code. +mm.txt + - Memory layout of x86-64 (4 level page tables, 46 bits physical). +uefi.txt + - Booting Linux via Unified Extensible Firmware Interface. diff --git a/Documentation/x86/x86_64/boot-options.txt b/Documentation/x86/x86_64/boot-options.txt new file mode 100644 index 000000000000..b0c7b6c4abda --- /dev/null +++ b/Documentation/x86/x86_64/boot-options.txt @@ -0,0 +1,314 @@ +AMD64 specific boot options + +There are many others (usually documented in driver documentation), but +only the AMD64 specific ones are listed here. + +Machine check + + mce=off disable machine check + mce=bootlog Enable logging of machine checks left over from booting. + Disabled by default on AMD because some BIOS leave bogus ones. + If your BIOS doesn't do that it's a good idea to enable though + to make sure you log even machine check events that result + in a reboot. On Intel systems it is enabled by default. + mce=nobootlog + Disable boot machine check logging. + mce=tolerancelevel (number) + 0: always panic on uncorrected errors, log corrected errors + 1: panic or SIGBUS on uncorrected errors, log corrected errors + 2: SIGBUS or log uncorrected errors, log corrected errors + 3: never panic or SIGBUS, log all errors (for testing only) + Default is 1 + Can be also set using sysfs which is preferable. + + nomce (for compatibility with i386): same as mce=off + + Everything else is in sysfs now. + +APICs + + apic Use IO-APIC. Default + + noapic Don't use the IO-APIC. + + disableapic Don't use the local APIC + + nolapic Don't use the local APIC (alias for i386 compatibility) + + pirq=... See Documentation/i386/IO-APIC.txt + + noapictimer Don't set up the APIC timer + + no_timer_check Don't check the IO-APIC timer. This can work around + problems with incorrect timer initialization on some boards. + + apicmaintimer Run time keeping from the local APIC timer instead + of using the PIT/HPET interrupt for this. This is useful + when the PIT/HPET interrupts are unreliable. + + noapicmaintimer Don't do time keeping using the APIC timer. + Useful when this option was auto selected, but doesn't work. + + apicpmtimer + Do APIC timer calibration using the pmtimer. Implies + apicmaintimer. Useful when your PIT timer is totally + broken. + + disable_8254_timer / enable_8254_timer + Enable interrupt 0 timer routing over the 8254 in addition to over + the IO-APIC. The kernel tries to set a sensible default. + +Early Console + + syntax: earlyprintk=vga + earlyprintk=serial[,ttySn[,baudrate]] + + The early console is useful when the kernel crashes before the + normal console is initialized. It is not enabled by + default because it has some cosmetic problems. + Append ,keep to not disable it when the real console takes over. + Only vga or serial at a time, not both. + Currently only ttyS0 and ttyS1 are supported. + Interaction with the standard serial driver is not very good. + The VGA output is eventually overwritten by the real console. + +Timing + + notsc + Don't use the CPU time stamp counter to read the wall time. + This can be used to work around timing problems on multiprocessor systems + with not properly synchronized CPUs. + + report_lost_ticks + Report when timer interrupts are lost because some code turned off + interrupts for too long. + + nmi_watchdog=NUMBER[,panic] + NUMBER can be: + 0 don't use an NMI watchdog + 1 use the IO-APIC timer for the NMI watchdog + 2 use the local APIC for the NMI watchdog using a performance counter. Note + This will use one performance counter and the local APIC's performance + vector. + When panic is specified panic when an NMI watchdog timeout occurs. + This is useful when you use a panic=... timeout and need the box + quickly up again. + + nohpet + Don't use the HPET timer. + +Idle loop + + idle=poll + Don't do power saving in the idle loop using HLT, but poll for rescheduling + event. This will make the CPUs eat a lot more power, but may be useful + to get slightly better performance in multiprocessor benchmarks. It also + makes some profiling using performance counters more accurate. + Please note that on systems with MONITOR/MWAIT support (like Intel EM64T + CPUs) this option has no performance advantage over the normal idle loop. + It may also interact badly with hyperthreading. + +Rebooting + + reboot=b[ios] | t[riple] | k[bd] | a[cpi] | e[fi] [, [w]arm | [c]old] + bios Use the CPU reboot vector for warm reset + warm Don't set the cold reboot flag + cold Set the cold reboot flag + triple Force a triple fault (init) + kbd Use the keyboard controller. cold reset (default) + acpi Use the ACPI RESET_REG in the FADT. If ACPI is not configured or the + ACPI reset does not work, the reboot path attempts the reset using + the keyboard controller. + efi Use efi reset_system runtime service. If EFI is not configured or the + EFI reset does not work, the reboot path attempts the reset using + the keyboard controller. + + Using warm reset will be much faster especially on big memory + systems because the BIOS will not go through the memory check. + Disadvantage is that not all hardware will be completely reinitialized + on reboot so there may be boot problems on some systems. + + reboot=force + + Don't stop other CPUs on reboot. This can make reboot more reliable + in some cases. + +Non Executable Mappings + + noexec=on|off + + on Enable(default) + off Disable + +SMP + + additional_cpus=NUM Allow NUM more CPUs for hotplug + (defaults are specified by the BIOS, see Documentation/x86_64/cpu-hotplug-spec) + +NUMA + + numa=off Only set up a single NUMA node spanning all memory. + + numa=noacpi Don't parse the SRAT table for NUMA setup + + numa=fake=CMDLINE + If a number, fakes CMDLINE nodes and ignores NUMA setup of the + actual machine. Otherwise, system memory is configured + depending on the sizes and coefficients listed. For example: + numa=fake=2*512,1024,4*256,*128 + gives two 512M nodes, a 1024M node, four 256M nodes, and the + rest split into 128M chunks. If the last character of CMDLINE + is a *, the remaining memory is divided up equally among its + coefficient: + numa=fake=2*512,2* + gives two 512M nodes and the rest split into two nodes. + Otherwise, the remaining system RAM is allocated to an + additional node. + + numa=hotadd=percent + Only allow hotadd memory to preallocate page structures upto + percent of already available memory. + numa=hotadd=0 will disable hotadd memory. + +ACPI + + acpi=off Don't enable ACPI + acpi=ht Use ACPI boot table parsing, but don't enable ACPI + interpreter + acpi=force Force ACPI on (currently not needed) + + acpi=strict Disable out of spec ACPI workarounds. + + acpi_sci={edge,level,high,low} Set up ACPI SCI interrupt. + + acpi=noirq Don't route interrupts + +PCI + + pci=off Don't use PCI + pci=conf1 Use conf1 access. + pci=conf2 Use conf2 access. + pci=rom Assign ROMs. + pci=assign-busses Assign busses + pci=irqmask=MASK Set PCI interrupt mask to MASK + pci=lastbus=NUMBER Scan upto NUMBER busses, no matter what the mptable says. + pci=noacpi Don't use ACPI to set up PCI interrupt routing. + +IOMMU (input/output memory management unit) + + Currently four x86-64 PCI-DMA mapping implementations exist: + + 1. <arch/x86_64/kernel/pci-nommu.c>: use no hardware/software IOMMU at all + (e.g. because you have < 3 GB memory). + Kernel boot message: "PCI-DMA: Disabling IOMMU" + + 2. <arch/x86_64/kernel/pci-gart.c>: AMD GART based hardware IOMMU. + Kernel boot message: "PCI-DMA: using GART IOMMU" + + 3. <arch/x86_64/kernel/pci-swiotlb.c> : Software IOMMU implementation. Used + e.g. if there is no hardware IOMMU in the system and it is need because + you have >3GB memory or told the kernel to us it (iommu=soft)) + Kernel boot message: "PCI-DMA: Using software bounce buffering + for IO (SWIOTLB)" + + 4. <arch/x86_64/pci-calgary.c> : IBM Calgary hardware IOMMU. Used in IBM + pSeries and xSeries servers. This hardware IOMMU supports DMA address + mapping with memory protection, etc. + Kernel boot message: "PCI-DMA: Using Calgary IOMMU" + + iommu=[<size>][,noagp][,off][,force][,noforce][,leak[=<nr_of_leak_pages>] + [,memaper[=<order>]][,merge][,forcesac][,fullflush][,nomerge] + [,noaperture][,calgary] + + General iommu options: + off Don't initialize and use any kind of IOMMU. + noforce Don't force hardware IOMMU usage when it is not needed. + (default). + force Force the use of the hardware IOMMU even when it is + not actually needed (e.g. because < 3 GB memory). + soft Use software bounce buffering (SWIOTLB) (default for + Intel machines). This can be used to prevent the usage + of an available hardware IOMMU. + + iommu options only relevant to the AMD GART hardware IOMMU: + <size> Set the size of the remapping area in bytes. + allowed Overwrite iommu off workarounds for specific chipsets. + fullflush Flush IOMMU on each allocation (default). + nofullflush Don't use IOMMU fullflush. + leak Turn on simple iommu leak tracing (only when + CONFIG_IOMMU_LEAK is on). Default number of leak pages + is 20. + memaper[=<order>] Allocate an own aperture over RAM with size 32MB<<order. + (default: order=1, i.e. 64MB) + merge Do scatter-gather (SG) merging. Implies "force" + (experimental). + nomerge Don't do scatter-gather (SG) merging. + noaperture Ask the IOMMU not to touch the aperture for AGP. + forcesac Force single-address cycle (SAC) mode for masks <40bits + (experimental). + noagp Don't initialize the AGP driver and use full aperture. + allowdac Allow double-address cycle (DAC) mode, i.e. DMA >4GB. + DAC is used with 32-bit PCI to push a 64-bit address in + two cycles. When off all DMA over >4GB is forced through + an IOMMU or software bounce buffering. + nodac Forbid DAC mode, i.e. DMA >4GB. + panic Always panic when IOMMU overflows. + calgary Use the Calgary IOMMU if it is available + + iommu options only relevant to the software bounce buffering (SWIOTLB) IOMMU + implementation: + swiotlb=<pages>[,force] + <pages> Prereserve that many 128K pages for the software IO + bounce buffering. + force Force all IO through the software TLB. + + Settings for the IBM Calgary hardware IOMMU currently found in IBM + pSeries and xSeries machines: + + calgary=[64k,128k,256k,512k,1M,2M,4M,8M] + calgary=[translate_empty_slots] + calgary=[disable=<PCI bus number>] + panic Always panic when IOMMU overflows + + 64k,...,8M - Set the size of each PCI slot's translation table + when using the Calgary IOMMU. This is the size of the translation + table itself in main memory. The smallest table, 64k, covers an IO + space of 32MB; the largest, 8MB table, can cover an IO space of + 4GB. Normally the kernel will make the right choice by itself. + + translate_empty_slots - Enable translation even on slots that have + no devices attached to them, in case a device will be hotplugged + in the future. + + disable=<PCI bus number> - Disable translation on a given PHB. For + example, the built-in graphics adapter resides on the first bridge + (PCI bus number 0); if translation (isolation) is enabled on this + bridge, X servers that access the hardware directly from user + space might stop working. Use this option if you have devices that + are accessed from userspace directly on some PCI host bridge. + +Debugging + + oops=panic Always panic on oopses. Default is to just kill the process, + but there is a small probability of deadlocking the machine. + This will also cause panics on machine check exceptions. + Useful together with panic=30 to trigger a reboot. + + kstack=N Print N words from the kernel stack in oops dumps. + + pagefaulttrace Dump all page faults. Only useful for extreme debugging + and will create a lot of output. + + call_trace=[old|both|newfallback|new] + old: use old inexact backtracer + new: use new exact dwarf2 unwinder + both: print entries from both + newfallback: use new unwinder but fall back to old if it gets + stuck (default) + +Miscellaneous + + nogbpages + Do not use GB pages for kernel direct mappings. + gbpages + Use GB pages for kernel direct mappings. diff --git a/Documentation/x86/x86_64/cpu-hotplug-spec b/Documentation/x86/x86_64/cpu-hotplug-spec new file mode 100644 index 000000000000..3c23e0587db3 --- /dev/null +++ b/Documentation/x86/x86_64/cpu-hotplug-spec @@ -0,0 +1,21 @@ +Firmware support for CPU hotplug under Linux/x86-64 +--------------------------------------------------- + +Linux/x86-64 supports CPU hotplug now. For various reasons Linux wants to +know in advance of boot time the maximum number of CPUs that could be plugged +into the system. ACPI 3.0 currently has no official way to supply +this information from the firmware to the operating system. + +In ACPI each CPU needs an LAPIC object in the MADT table (5.2.11.5 in the +ACPI 3.0 specification). ACPI already has the concept of disabled LAPIC +objects by setting the Enabled bit in the LAPIC object to zero. + +For CPU hotplug Linux/x86-64 expects now that any possible future hotpluggable +CPU is already available in the MADT. If the CPU is not available yet +it should have its LAPIC Enabled bit set to 0. Linux will use the number +of disabled LAPICs to compute the maximum number of future CPUs. + +In the worst case the user can overwrite this choice using a command line +option (additional_cpus=...), but it is recommended to supply the correct +number (or a reasonable approximation of it, with erring towards more not less) +in the MADT to avoid manual configuration. diff --git a/Documentation/x86/x86_64/fake-numa-for-cpusets b/Documentation/x86/x86_64/fake-numa-for-cpusets new file mode 100644 index 000000000000..d1a985c5b00a --- /dev/null +++ b/Documentation/x86/x86_64/fake-numa-for-cpusets @@ -0,0 +1,66 @@ +Using numa=fake and CPUSets for Resource Management +Written by David Rientjes <rientjes@cs.washington.edu> + +This document describes how the numa=fake x86_64 command-line option can be used +in conjunction with cpusets for coarse memory management. Using this feature, +you can create fake NUMA nodes that represent contiguous chunks of memory and +assign them to cpusets and their attached tasks. This is a way of limiting the +amount of system memory that are available to a certain class of tasks. + +For more information on the features of cpusets, see Documentation/cpusets.txt. +There are a number of different configurations you can use for your needs. For +more information on the numa=fake command line option and its various ways of +configuring fake nodes, see Documentation/x86_64/boot-options.txt. + +For the purposes of this introduction, we'll assume a very primitive NUMA +emulation setup of "numa=fake=4*512,". This will split our system memory into +four equal chunks of 512M each that we can now use to assign to cpusets. As +you become more familiar with using this combination for resource control, +you'll determine a better setup to minimize the number of nodes you have to deal +with. + +A machine may be split as follows with "numa=fake=4*512," as reported by dmesg: + + Faking node 0 at 0000000000000000-0000000020000000 (512MB) + Faking node 1 at 0000000020000000-0000000040000000 (512MB) + Faking node 2 at 0000000040000000-0000000060000000 (512MB) + Faking node 3 at 0000000060000000-0000000080000000 (512MB) + ... + On node 0 totalpages: 130975 + On node 1 totalpages: 131072 + On node 2 totalpages: 131072 + On node 3 totalpages: 131072 + +Now following the instructions for mounting the cpusets filesystem from +Documentation/cpusets.txt, you can assign fake nodes (i.e. contiguous memory +address spaces) to individual cpusets: + + [root@xroads /]# mkdir exampleset + [root@xroads /]# mount -t cpuset none exampleset + [root@xroads /]# mkdir exampleset/ddset + [root@xroads /]# cd exampleset/ddset + [root@xroads /exampleset/ddset]# echo 0-1 > cpus + [root@xroads /exampleset/ddset]# echo 0-1 > mems + +Now this cpuset, 'ddset', will only allowed access to fake nodes 0 and 1 for +memory allocations (1G). + +You can now assign tasks to these cpusets to limit the memory resources +available to them according to the fake nodes assigned as mems: + + [root@xroads /exampleset/ddset]# echo $$ > tasks + [root@xroads /exampleset/ddset]# dd if=/dev/zero of=tmp bs=1024 count=1G + [1] 13425 + +Notice the difference between the system memory usage as reported by +/proc/meminfo between the restricted cpuset case above and the unrestricted +case (i.e. running the same 'dd' command without assigning it to a fake NUMA +cpuset): + Unrestricted Restricted + MemTotal: 3091900 kB 3091900 kB + MemFree: 42113 kB 1513236 kB + +This allows for coarse memory management for the tasks you assign to particular +cpusets. Since cpusets can form a hierarchy, you can create some pretty +interesting combinations of use-cases for various classes of tasks for your +memory management needs. diff --git a/Documentation/x86/x86_64/kernel-stacks b/Documentation/x86/x86_64/kernel-stacks new file mode 100644 index 000000000000..5ad65d51fb95 --- /dev/null +++ b/Documentation/x86/x86_64/kernel-stacks @@ -0,0 +1,99 @@ +Most of the text from Keith Owens, hacked by AK + +x86_64 page size (PAGE_SIZE) is 4K. + +Like all other architectures, x86_64 has a kernel stack for every +active thread. These thread stacks are THREAD_SIZE (2*PAGE_SIZE) big. +These stacks contain useful data as long as a thread is alive or a +zombie. While the thread is in user space the kernel stack is empty +except for the thread_info structure at the bottom. + +In addition to the per thread stacks, there are specialized stacks +associated with each CPU. These stacks are only used while the kernel +is in control on that CPU; when a CPU returns to user space the +specialized stacks contain no useful data. The main CPU stacks are: + +* Interrupt stack. IRQSTACKSIZE + + Used for external hardware interrupts. If this is the first external + hardware interrupt (i.e. not a nested hardware interrupt) then the + kernel switches from the current task to the interrupt stack. Like + the split thread and interrupt stacks on i386 (with CONFIG_4KSTACKS), + this gives more room for kernel interrupt processing without having + to increase the size of every per thread stack. + + The interrupt stack is also used when processing a softirq. + +Switching to the kernel interrupt stack is done by software based on a +per CPU interrupt nest counter. This is needed because x86-64 "IST" +hardware stacks cannot nest without races. + +x86_64 also has a feature which is not available on i386, the ability +to automatically switch to a new stack for designated events such as +double fault or NMI, which makes it easier to handle these unusual +events on x86_64. This feature is called the Interrupt Stack Table +(IST). There can be up to 7 IST entries per CPU. The IST code is an +index into the Task State Segment (TSS). The IST entries in the TSS +point to dedicated stacks; each stack can be a different size. + +An IST is selected by a non-zero value in the IST field of an +interrupt-gate descriptor. When an interrupt occurs and the hardware +loads such a descriptor, the hardware automatically sets the new stack +pointer based on the IST value, then invokes the interrupt handler. If +software wants to allow nested IST interrupts then the handler must +adjust the IST values on entry to and exit from the interrupt handler. +(This is occasionally done, e.g. for debug exceptions.) + +Events with different IST codes (i.e. with different stacks) can be +nested. For example, a debug interrupt can safely be interrupted by an +NMI. arch/x86_64/kernel/entry.S::paranoidentry adjusts the stack +pointers on entry to and exit from all IST events, in theory allowing +IST events with the same code to be nested. However in most cases, the +stack size allocated to an IST assumes no nesting for the same code. +If that assumption is ever broken then the stacks will become corrupt. + +The currently assigned IST stacks are :- + +* STACKFAULT_STACK. EXCEPTION_STKSZ (PAGE_SIZE). + + Used for interrupt 12 - Stack Fault Exception (#SS). + + This allows the CPU to recover from invalid stack segments. Rarely + happens. + +* DOUBLEFAULT_STACK. EXCEPTION_STKSZ (PAGE_SIZE). + + Used for interrupt 8 - Double Fault Exception (#DF). + + Invoked when handling one exception causes another exception. Happens + when the kernel is very confused (e.g. kernel stack pointer corrupt). + Using a separate stack allows the kernel to recover from it well enough + in many cases to still output an oops. + +* NMI_STACK. EXCEPTION_STKSZ (PAGE_SIZE). + + Used for non-maskable interrupts (NMI). + + NMI can be delivered at any time, including when the kernel is in the + middle of switching stacks. Using IST for NMI events avoids making + assumptions about the previous state of the kernel stack. + +* DEBUG_STACK. DEBUG_STKSZ + + Used for hardware debug interrupts (interrupt 1) and for software + debug interrupts (INT3). + + When debugging a kernel, debug interrupts (both hardware and + software) can occur at any time. Using IST for these interrupts + avoids making assumptions about the previous state of the kernel + stack. + +* MCE_STACK. EXCEPTION_STKSZ (PAGE_SIZE). + + Used for interrupt 18 - Machine Check Exception (#MC). + + MCE can be delivered at any time, including when the kernel is in the + middle of switching stacks. Using IST for MCE events avoids making + assumptions about the previous state of the kernel stack. + +For more details see the Intel IA32 or AMD AMD64 architecture manuals. diff --git a/Documentation/x86/x86_64/machinecheck b/Documentation/x86/x86_64/machinecheck new file mode 100644 index 000000000000..a05e58e7b159 --- /dev/null +++ b/Documentation/x86/x86_64/machinecheck @@ -0,0 +1,77 @@ + +Configurable sysfs parameters for the x86-64 machine check code. + +Machine checks report internal hardware error conditions detected +by the CPU. Uncorrected errors typically cause a machine check +(often with panic), corrected ones cause a machine check log entry. + +Machine checks are organized in banks (normally associated with +a hardware subsystem) and subevents in a bank. The exact meaning +of the banks and subevent is CPU specific. + +mcelog knows how to decode them. + +When you see the "Machine check errors logged" message in the system +log then mcelog should run to collect and decode machine check entries +from /dev/mcelog. Normally mcelog should be run regularly from a cronjob. + +Each CPU has a directory in /sys/devices/system/machinecheck/machinecheckN +(N = CPU number) + +The directory contains some configurable entries: + +Entries: + +bankNctl +(N bank number) + 64bit Hex bitmask enabling/disabling specific subevents for bank N + When a bit in the bitmask is zero then the respective + subevent will not be reported. + By default all events are enabled. + Note that BIOS maintain another mask to disable specific events + per bank. This is not visible here + +The following entries appear for each CPU, but they are truly shared +between all CPUs. + +check_interval + How often to poll for corrected machine check errors, in seconds + (Note output is hexademical). Default 5 minutes. When the poller + finds MCEs it triggers an exponential speedup (poll more often) on + the polling interval. When the poller stops finding MCEs, it + triggers an exponential backoff (poll less often) on the polling + interval. The check_interval variable is both the initial and + maximum polling interval. + +tolerant + Tolerance level. When a machine check exception occurs for a non + corrected machine check the kernel can take different actions. + Since machine check exceptions can happen any time it is sometimes + risky for the kernel to kill a process because it defies + normal kernel locking rules. The tolerance level configures + how hard the kernel tries to recover even at some risk of + deadlock. Higher tolerant values trade potentially better uptime + with the risk of a crash or even corruption (for tolerant >= 3). + + 0: always panic on uncorrected errors, log corrected errors + 1: panic or SIGBUS on uncorrected errors, log corrected errors + 2: SIGBUS or log uncorrected errors, log corrected errors + 3: never panic or SIGBUS, log all errors (for testing only) + + Default: 1 + + Note this only makes a difference if the CPU allows recovery + from a machine check exception. Current x86 CPUs generally do not. + +trigger + Program to run when a machine check event is detected. + This is an alternative to running mcelog regularly from cron + and allows to detect events faster. + +TBD document entries for AMD threshold interrupt configuration + +For more details about the x86 machine check architecture +see the Intel and AMD architecture manuals from their developer websites. + +For more details about the architecture see +see http://one.firstfloor.org/~andi/mce.pdf diff --git a/Documentation/x86/x86_64/mm.txt b/Documentation/x86/x86_64/mm.txt new file mode 100644 index 000000000000..efce75097369 --- /dev/null +++ b/Documentation/x86/x86_64/mm.txt @@ -0,0 +1,28 @@ + +<previous description obsolete, deleted> + +Virtual memory map with 4 level page tables: + +0000000000000000 - 00007fffffffffff (=47 bits) user space, different per mm +hole caused by [48:63] sign extension +ffff800000000000 - ffff80ffffffffff (=40 bits) guard hole +ffff810000000000 - ffffc0ffffffffff (=46 bits) direct mapping of all phys. memory +ffffc10000000000 - ffffc1ffffffffff (=40 bits) hole +ffffc20000000000 - ffffe1ffffffffff (=45 bits) vmalloc/ioremap space +ffffe20000000000 - ffffe2ffffffffff (=40 bits) virtual memory map (1TB) +... unused hole ... +ffffffff80000000 - ffffffffa0000000 (=512 MB) kernel text mapping, from phys 0 +ffffffffa0000000 - fffffffffff00000 (=1536 MB) module mapping space + +The direct mapping covers all memory in the system up to the highest +memory address (this means in some cases it can also include PCI memory +holes). + +vmalloc space is lazily synchronized into the different PML4 pages of +the processes using the page fault handler, with init_level4_pgt as +reference. + +Current X86-64 implementations only support 40 bits of address space, +but we support up to 46 bits. This expands into MBZ space in the page tables. + +-Andi Kleen, Jul 2004 diff --git a/Documentation/x86/x86_64/uefi.txt b/Documentation/x86/x86_64/uefi.txt new file mode 100644 index 000000000000..7d77120a5184 --- /dev/null +++ b/Documentation/x86/x86_64/uefi.txt @@ -0,0 +1,38 @@ +General note on [U]EFI x86_64 support +------------------------------------- + +The nomenclature EFI and UEFI are used interchangeably in this document. + +Although the tools below are _not_ needed for building the kernel, +the needed bootloader support and associated tools for x86_64 platforms +with EFI firmware and specifications are listed below. + +1. UEFI specification: http://www.uefi.org + +2. Booting Linux kernel on UEFI x86_64 platform requires bootloader + support. Elilo with x86_64 support can be used. + +3. x86_64 platform with EFI/UEFI firmware. + +Mechanics: +--------- +- Build the kernel with the following configuration. + CONFIG_FB_EFI=y + CONFIG_FRAMEBUFFER_CONSOLE=y + If EFI runtime services are expected, the following configuration should + be selected. + CONFIG_EFI=y + CONFIG_EFI_VARS=y or m # optional +- Create a VFAT partition on the disk +- Copy the following to the VFAT partition: + elilo bootloader with x86_64 support, elilo configuration file, + kernel image built in first step and corresponding + initrd. Instructions on building elilo and its dependencies + can be found in the elilo sourceforge project. +- Boot to EFI shell and invoke elilo choosing the kernel image built + in first step. +- If some or all EFI runtime services don't work, you can try following + kernel command line parameters to turn off some or all EFI runtime + services. + noefi turn off all EFI runtime services + reboot_type=k turn off EFI reboot runtime service |