diff options
Diffstat (limited to 'Documentation')
11 files changed, 210 insertions, 42 deletions
diff --git a/Documentation/devicetree/bindings/input/adc-keys.txt b/Documentation/devicetree/bindings/input/adc-keys.txt new file mode 100644 index 000000000000..e551814629b4 --- /dev/null +++ b/Documentation/devicetree/bindings/input/adc-keys.txt @@ -0,0 +1,49 @@ +ADC attached resistor ladder buttons +------------------------------------ + +Required properties: + - compatible: "adc-keys" + - io-channels: Phandle to an ADC channel + - io-channel-names = "buttons"; + - keyup-threshold-microvolt: Voltage at which all the keys are considered up. + +Optional properties: + - poll-interval: Poll interval time in milliseconds + - autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem. + +Each button (key) is represented as a sub-node of "adc-keys": + +Required subnode-properties: + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + - press-threshold-microvolt: Voltage ADC input when this key is pressed. + +Example: + +#include <dt-bindings/input/input.h> + + adc-keys { + compatible = "adc-keys"; + io-channels = <&lradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <2000000>; + + button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <1500000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <1000000>; + }; + + button-enter { + label = "Enter"; + linux,code = <KEY_ENTER>; + press-threshold-microvolt = <500000>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-decoder.txt b/Documentation/devicetree/bindings/input/gpio-decoder.txt new file mode 100644 index 000000000000..14a77fb96cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-decoder.txt @@ -0,0 +1,23 @@ +* GPIO Decoder DT bindings + +Required Properties: +- compatible: should be "gpio-decoder" +- gpios: a spec of gpios (at least two) to be decoded to a number with + first entry representing the MSB. + +Optional Properties: +- decoder-max-value: Maximum possible value that can be reported by + the gpios. +- linux,axis: the input subsystem axis to map to (ABS_X/ABS_Y). + Defaults to 0 (ABS_X). + +Example: + gpio-decoder0 { + compatible = "gpio-decoder"; + gpios = <&pca9536 3 GPIO_ACTIVE_HIGH>, + <&pca9536 2 GPIO_ACTIVE_HIGH>, + <&pca9536 1 GPIO_ACTIVE_HIGH>, + <&pca9536 0 GPIO_ACTIVE_HIGH>; + linux,axis = <0>; /* ABS_X */ + decoder-max-value = <9>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt index 95d0fb11a787..4d9a3717eaaf 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt @@ -34,11 +34,10 @@ Example nodes: gpio_keys_polled { compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; poll-interval = <100>; autorepeat; - button@21 { + + button21 { label = "GPIO Key UP"; linux,code = <103>; gpios = <&gpio1 0 1>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index f99528da1b1d..6db22103e2dd 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -19,6 +19,7 @@ Required properties: or: "edt,edt-ft5306" or: "edt,edt-ft5406" or: "edt,edt-ft5506" + or: "focaltech,ft6236" - reg: I2C slave address of the chip (0x38) - interrupt-parent: a phandle pointing to the interrupt controller @@ -43,6 +44,13 @@ Optional properties: - offset: allows setting the edge compensation in the range from 0 to 31. + - touchscreen-size-x : See touchscreen.txt + - touchscreen-size-y : See touchscreen.txt + - touchscreen-fuzz-x : See touchscreen.txt + - touchscreen-fuzz-y : See touchscreen.txt + - touchscreen-inverted-x : See touchscreen.txt + - touchscreen-inverted-y : See touchscreen.txt + - touchscreen-swapped-x-y : See touchscreen.txt Example: polytouch: edt-ft5x06@38 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt new file mode 100644 index 000000000000..5a19f4c3e9d7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt @@ -0,0 +1,27 @@ +* Elan eKTF2127 I2C touchscreen controller + +Required properties: + - compatible : "elan,ektf2127" + - reg : I2C slave address of the chip (0x40) + - interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts : interrupt specification for the ektf2127 interrupt + - power-gpios : GPIO specification for the pin connected to the + ektf2127's wake input. This needs to be driven high + to take ektf2127 out of it's low power state + +For additional optional properties see: touchscreen.txt + +Example: + +i2c@00000000 { + ektf2127: touchscreen@15 { + compatible = "elan,ektf2127"; + reg = <0x15>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt b/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt deleted file mode 100644 index 777521da3da5..000000000000 --- a/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt +++ /dev/null @@ -1,35 +0,0 @@ -* FocalTech FT6236 I2C touchscreen controller - -Required properties: - - compatible : "focaltech,ft6236" - - reg : I2C slave address of the chip (0x38) - - interrupt-parent : a phandle pointing to the interrupt controller - serving the interrupt for this chip - - interrupts : interrupt specification for the touch controller - interrupt - - reset-gpios : GPIO specification for the RSTN input - - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) - - touchscreen-size-y : vertical resolution of touchscreen (in pixels) - -Optional properties: - - touchscreen-fuzz-x : horizontal noise value of the absolute input - device (in pixels) - - touchscreen-fuzz-y : vertical noise value of the absolute input - device (in pixels) - - touchscreen-inverted-x : X axis is inverted (boolean) - - touchscreen-inverted-y : Y axis is inverted (boolean) - - touchscreen-swapped-x-y: X and Y axis are swapped (boolean) - Swapping is done after inverting the axis - -Example: - - ft6x06@38 { - compatible = "focaltech,ft6236"; - reg = <0x38>; - interrupt-parent = <&gpio>; - interrupts = <23 2>; - touchscreen-size-x = <320>; - touchscreen-size-y = <480>; - touchscreen-inverted-x; - touchscreen-swapped-x-y; - }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt new file mode 100644 index 000000000000..7b8944c2cb31 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt @@ -0,0 +1,21 @@ +* MELFAS MIP4 Touchscreen + +Required properties: +- compatible: must be "melfas,mip4_ts" +- reg: I2C slave address of the chip (0x48 or 0x34) +- interrupt-parent: interrupt controller to which the chip is connected +- interrupts: interrupt to which the chip is connected + +Optional properties: +- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip + +Example: + i2c@00000000 { + touchscreen: melfas_mip4@48 { + compatible = "melfas,mip4_ts"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt index e30e0b93f2b3..3e5b9793341f 100644 --- a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -1,13 +1,24 @@ -Texas Instruments TPS65218 power button +Texas Instruments TPS65217 and TPS65218 power button + +This module is part of the TPS65217/TPS65218. For more details about the whole +TPS65217 chip see Documentation/devicetree/bindings/regulator/tps65217.txt. This driver provides a simple power button event via an Interrupt. Required properties: -- compatible: should be "ti,tps65218-pwrbutton" +- compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton" + +Required properties for TPS65218: - interrupts: should be one of the following - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 -Example: +Examples: + +&tps { + tps65217-pwrbutton { + compatible = "ti,tps65217-pwrbutton"; + }; +}; &tps { power-button { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 1992aa97d45a..4e3d7d4e315e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -156,6 +156,7 @@ maxim Maxim Integrated Products meas Measurement Specialties mediatek MediaTek Inc. melexis Melexis N.V. +melfas MELFAS Inc. merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index 1fec1135791d..8d1341ccde64 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -319,3 +319,60 @@ For touchpad packet, the format is: otherwise byte 0 bit 4 must be set and byte 0/4/5 are in NEW fmt F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ... + + +ALPS Absolute Mode - Protocol Version 8 +--------------------------------------- + +Spoken by SS4 (73 03 14) and SS5 (73 03 28) hardware. + +The packet type is given by the APD field, bits 4-5 of byte 3. + +Touchpad packet (APD = 0x2): + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 0 0 X7 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: 0 T&P 1 0 1 0 0 Y7 + byte 4: 0 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 0 0 0 0 0 0 0 + +SWM, SWR, SWL: Middle, Right, and Left button states + +Touchpad 1 Finger packet (APD = 0x0): + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 X2 X1 X0 + byte 1: X9 X8 X7 1 X6 X5 X4 X3 + byte 2: 0 X11 X10 LFB Y3 Y2 Y1 Y0 + byte 3: Y5 Y4 0 0 1 TAPF2 TAPF1 TAPF0 + byte 4: Zv7 Y11 Y10 1 Y9 Y8 Y7 Y6 + byte 5: Zv6 Zv5 Zv4 0 Zv3 Zv2 Zv1 Zv0 + +TAPF: ??? +LFB: ??? + +Touchpad 2 Finger packet (APD = 0x1): + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4 + byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0 + byte 2: AY11 AY10 AY9 CONT AY8 AY7 AY6 AY5 + byte 3: 0 0 0 1 1 BX6 BX5 BX4 + byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0 + byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5 + +CONT: A 3-or-4 Finger packet is to follow + +Touchpad 3-or-4 Finger packet (APD = 0x3): + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4 + byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0 + byte 2: AY11 AY10 AY9 OVF AY8 AY7 AY6 AY5 + byte 3: 0 0 1 1 1 BX6 BX5 BX4 + byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0 + byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5 + +OVF: 5th finger detected diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a4f4d693e2c1..46726d4899fe 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1457,7 +1457,14 @@ bytes respectively. Such letter suffixes can also be entirely omitted. i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX controllers i8042.notimeout [HW] Ignore timeout condition signalled by controller - i8042.reset [HW] Reset the controller during init and cleanup + i8042.reset [HW] Reset the controller during init, cleanup and + suspend-to-ram transitions, only during s2r + transitions, or never reset + Format: { 1 | Y | y | 0 | N | n } + 1, Y, y: always reset controller + 0, N, n: don't ever reset controller + Default: only on s2r transitions on x86; most other + architectures force reset to be always executed i8042.unlock [HW] Unlock (ignore) the keylock i8042.kbdreset [HW] Reset device connected to KBD port |