3 files changed, 0 insertions, 109 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
deleted file mode 100644
index 47fc64922fe0..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
+++ /dev/null
@@ -1,49 +0,0 @@
-Netlogic XLP Family GPIO
-========================
-
-This GPIO driver is used for following Netlogic XLP SoCs:
-	XLP832, XLP316, XLP208, XLP980, XLP532
-This GPIO driver is also compatible with GPIO controller found on
-Broadcom Vulcan ARM64.
-
-Required properties:
--------------------
-
-- compatible: Should be one of the following:
-  - "netlogic,xlp832-gpio": For Netlogic XLP832
-  - "netlogic,xlp316-gpio": For Netlogic XLP316
-  - "netlogic,xlp208-gpio": For Netlogic XLP208
-  - "netlogic,xlp980-gpio": For Netlogic XLP980
-  - "netlogic,xlp532-gpio": For Netlogic XLP532
-  - "brcm,vulcan-gpio": For Broadcom Vulcan ARM64
-- reg: Physical base address and length of the controller's registers.
-- #gpio-cells: Should be two. The first cell is the pin number and the second
-  cell is used to specify optional parameters (currently unused).
-- gpio-controller: Marks the device node as a GPIO controller.
-- nr-gpios: Number of GPIO pins supported by the controller.
-- interrupt-cells: Should be two. The first cell is the GPIO Number. The
-  second cell is used to specify flags. The following subset of flags is
-  supported:
-  - trigger type:
-	1 = low to high edge triggered.
-	2 = high to low edge triggered.
-	4 = active high level-sensitive.
-	8 = active low level-sensitive.
-- interrupts: Interrupt number for this device.
-- interrupt-controller: Identifies the node as an interrupt controller.
-
-Example:
-
-	gpio: xlp_gpio@34000 {
-		compatible = "netlogic,xlp316-gpio";
-		reg = <0 0x34100 0x1000
-		       0 0x35100 0x1000>;
-		#gpio-cells = <2>;
-		gpio-controller;
-		nr-gpios = <57>;
-
-		#interrupt-cells = <2>;
-		interrupt-parent = <&pic>;
-		interrupts = <39>;
-		interrupt-controller;
-	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt
deleted file mode 100644
index f818ef507ab7..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-Device tree configuration for the I2C controller on the XLP9xx/5xx SoC
-
-Required properties:
-- compatible      : should be "netlogic,xlp980-i2c"
-- reg             : bus address start and address range size of device
-- interrupts      : interrupt number
-
-Optional properties:
-- clock-frequency : frequency of bus clock in Hz
-                    Defaults to 100 KHz when the property is not specified
-
-Example:
-
-i2c0: i2c@113100 {
-	compatible = "netlogic,xlp980-i2c";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	reg = <0 0x113100 0x100>;
-	clock-frequency = <400000>;
-	interrupts = <30>;
-	interrupt-parent = <&pic>;
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-xlp.txt b/Documentation/devicetree/bindings/spi/spi-xlp.txt
deleted file mode 100644
index f4925ec0ed33..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-xlp.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-SPI Master controller for Netlogic XLP MIPS64 SOCs
-==================================================
-
-Currently this SPI controller driver is supported for the following
-Netlogic XLP SoCs:
-	XLP832, XLP316, XLP208, XLP980, XLP532
-
-Required properties:
-- compatible		: Should be "netlogic,xlp832-spi".
-- #address-cells	: Number of cells required to define a chip select address
-			  on the SPI bus.
-- #size-cells		: Should be zero.
-- reg			: Should contain register location and length.
-- clocks		: Phandle of the spi clock
-- interrupts		: Interrupt number used by this controller.
-
-SPI slave nodes must be children of the SPI master node and can contain
-properties described in Documentation/devicetree/bindings/spi/spi-bus.txt.
-
-Example:
-
-	spi: xlp_spi@3a100 {
-		compatible = "netlogic,xlp832-spi";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0 0x3a100 0x100>;
-		clocks = <&spi_clk>;
-		interrupts = <34>;
-		interrupt-parent = <&pic>;
-
-		spi_nor@1 {
-			compatible = "spansion,s25sl12801";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <1>;	/* Chip Select */
-			spi-max-frequency = <40000000>;
-		};
-};