5 files changed, 144 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt
new file mode 100644
index 000000000000..1b87b741fa8e
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt
@@ -0,0 +1,35 @@
+Broadcom Kona Family I2C
+=========================
+
+This I2C controller is used in the following Broadcom SoCs:
+
+  BCM11130
+  BCM11140
+  BCM11351
+  BCM28145
+  BCM28155
+
+Required Properties
+-------------------
+- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c"
+- reg: Physical base address and length of controller registers
+- interrupts: The interrupt number used by the controller
+- clocks: clock specifier for the kona i2c external clock
+- clock-frequency: The I2C bus frequency in Hz
+- #address-cells: Should be <1>
+- #size-cells: Should be <0>
+
+Refer to clocks/clock-bindings.txt for generic clock consumer
+properties.
+
+Example:
+
+i2c@3e016000 {
+	compatible = "brcm,bcm11351-i2c","brcm,kona-i2c";
+	reg = <0x3e016000 0x80>;
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&bsc1_clk>;
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
new file mode 100644
index 000000000000..056732cfdcee
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
@@ -0,0 +1,44 @@
+* Samsung's High Speed I2C controller
+
+The Samsung's High Speed I2C controller is used to interface with I2C devices
+at various speeds ranging from 100khz to 3.4Mhz.
+
+Required properties:
+  - compatible: value should be.
+      -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - #address-cells: always 1 (for i2c addresses)
+  - #size-cells: always 0
+
+  - Pinctrl:
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - clock-frequency: Desired operating frequency in Hz of the bus.
+    -> If not specified, the bus operates in fast-speed mode at
+       at 100khz.
+    -> If specified, the bus operates in high-speed mode only if the
+       clock-frequency is >= 1Mhz.
+
+Example:
+
+hsi2c@12ca0000 {
+	compatible = "samsung,exynos5-hsi2c";
+	reg = <0x12ca0000 0x100>;
+	interrupts = <56>;
+	clock-frequency = <100000>;
+
+	pinctrl-0 = <&i2c4_bus>;
+	pinctrl-names = "default";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
new file mode 100644
index 000000000000..897cfcd5ce92
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
@@ -0,0 +1,23 @@
+I2C for R-Car platforms
+
+Required properties:
+- compatible: Must be one of
+	"renesas,i2c-rcar"
+	"renesas,i2c-r8a7778"
+	"renesas,i2c-r8a7779"
+	"renesas,i2c-r8a7790"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: interrupt specifier.
+
+Optional properties:
+- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this
+  propoerty indicates the default frequency 100 kHz.
+
+Examples :
+
+i2c0: i2c@e6500000 {
+	compatible = "renesas,i2c-rcar-h2";
+	reg = <0 0xe6500000 0 0x428>;
+	interrupts = <0 174 0x4>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
new file mode 100644
index 000000000000..437e0db3823c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt
@@ -0,0 +1,41 @@
+ST SSC binding, for I2C mode operation
+
+Required properties :
+- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c"
+- reg : Offset and length of the register set for the device
+- interrupts : the interrupt specifier
+- clock-names: Must contain "ssc".
+- clocks: Must contain an entry for each name in clock-names. See the common
+  clock bindings.
+- A pinctrl state named "default" must be defined to set pins in mode of
+  operation for I2C transfer.
+
+Optional properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+  the default 100 kHz frequency will be used. As only Normal and Fast modes
+  are supported, possible values are 100000 and 400000.
+- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- A pinctrl state named "idle" could be defined to set pins in idle state
+  when I2C instance is not performing a transfer.
+- A pinctrl state named "sleep" could be defined to set pins in sleep state
+  when driver enters in suspend.
+
+
+
+Example :
+
+i2c0: i2c@fed40000 {
+	compatible	= "st,comms-ssc4-i2c";
+	reg		= <0xfed40000 0x110>;
+	interrupts	=  <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+	clocks		= <&CLK_S_ICN_REG_0>;
+	clock-names	= "ssc";
+	clock-frequency = <400000>;
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_i2c0_default>;
+	st,i2c-min-scl-pulse-width-us = <0>;
+	st,i2c-min-sda-pulse-width-us = <5>;
+};
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index d29dea0f3232..7b0dcdb57173 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -25,6 +25,7 @@ Supported adapters:
   * Intel Avoton (SOC)
   * Intel Wellsburg (PCH)
   * Intel Coleto Creek (PCH)
+  * Intel Wildcat Point-LP (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller