diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-pci | 10 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/designware-pcie.txt | 3 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt | 25 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/pci-keystone.txt | 63 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/xgene-pci.txt | 57 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/xilinx-pcie.txt | 62 | ||||
| -rw-r--r-- | Documentation/driver-model/devres.txt | 2 |
7 files changed, 221 insertions, 1 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci index 6615fda0abfb..ee6c04036492 100644 --- a/Documentation/ABI/testing/sysfs-bus-pci +++ b/Documentation/ABI/testing/sysfs-bus-pci @@ -65,6 +65,16 @@ Description: force a rescan of all PCI buses in the system, and re-discover previously removed devices. +What: /sys/bus/pci/devices/.../msi_bus +Date: September 2014 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a zero value to this attribute disallows MSI and + MSI-X for any future drivers of the device. If the device + is a bridge, MSI and MSI-X will be disallowed for future + drivers of all child devices under the bridge. Drivers + must be reloaded for the new setting to take effect. + What: /sys/bus/pci/devices/.../msi_irqs/ Date: September, 2011 Contact: Neil Horman <nhorman@tuxdriver.com> diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index ed0d9b9fff2b..9f4faa8e8d00 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -23,3 +23,6 @@ Required properties: Optional properties: - reset-gpio: gpio pin number of power good signal +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to + specify this property, to keep backwards compatibility a range of 0x00-0xff + is assumed if not present) diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 0823362548dc..d763e047c6ae 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -1,7 +1,10 @@ NVIDIA Tegra PCIe controller Required properties: -- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie" +- compatible: Must be one of: + - "nvidia,tegra20-pcie" + - "nvidia,tegra30-pcie" + - "nvidia,tegra124-pcie" - device_type: Must be "pci" - reg: A list of physical base address and length for each set of controller registers. Must contain an entry for each entry in the reg-names property. @@ -57,6 +60,11 @@ Required properties: - afi - pcie_x +Required properties on Tegra124 and later: +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -84,6 +92,21 @@ Power supplies for Tegra30: - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 000000000000..54eae2938174 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,63 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on Designware PCI h/w version 3.65. +It shares common functions with PCIe Designware core driver and inherit +common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +for the details of Designware DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to Generic Keystone SerDes phy for PCI + phy-names: name of the Generic Keystine SerDes phy for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + +Designware DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt new file mode 100644 index 000000000000..1070b068c7c6 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -0,0 +1,57 @@ +* AppliedMicro X-Gene PCIe interface + +Required properties: +- device_type: set to "pci" +- compatible: should contain "apm,xgene-pcie" to identify the core. +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "csr": controller configuration registers. + "cfg": pcie configuration space registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- ranges: ranges for the outbound memory, I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if dma operations are coherent + +Example: + +SoC specific DT Entry: + + pcie0: pcie@1f2b0000 { + status = "disabled"; + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + }; + + +Board specific DT Entry: + &pcie0 { + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt new file mode 100644 index 000000000000..3e2c88d97ad4 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -0,0 +1,62 @@ +* Xilinx AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a" +- reg: Should contain AXI PCIe registers location and length +- device_type: must be "pci" +- interrupts: Should contain AXI PCIe interrupt +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + +Optional properties: +- bus-range: PCI bus numbers covered + +Interrupt controller child node ++++++++++++++++++++++++++++++++ +Required properties: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +NOTE: +The core provides a single interrupt for both INTx/MSI messages. So, +created a interrupt controller node to support 'interrupt-map' DT +functionality. The driver will create an IRQ domain for this map, decode +the four INTx interrupts in ISR and route them to this domain. + + +Example: +++++++++ + + pci_express: axi-pcie@50000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = < 0x50000000 0x10000000 >; + device_type = "pci"; + interrupts = < 0 52 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + } + }; diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index 40677443c0c5..b5ab416cd53a 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -264,8 +264,10 @@ IIO IO region devm_release_mem_region() devm_release_region() + devm_release_resource() devm_request_mem_region() devm_request_region() + devm_request_resource() IOMAP devm_ioport_map() |