diff options
Diffstat (limited to 'arch/arm/boot/dts/meson8b-ec100.dts')
| -rw-r--r-- | arch/arm/boot/dts/meson8b-ec100.dts | 128 |
1 files changed, 128 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts index d50fc2f60fa3..3ca9638fad09 100644 --- a/arch/arm/boot/dts/meson8b-ec100.dts +++ b/arch/arm/boot/dts/meson8b-ec100.dts @@ -23,6 +23,7 @@ }; memory { + device_type = "memory"; reg = <0x40000000 0x40000000>; }; @@ -64,6 +65,11 @@ timeout-ms = <20000>; }; + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&saradc 8>; + }; + leds { compatible = "gpio-leds"; @@ -83,6 +89,9 @@ }; usb_vbus: regulator-usb-vbus { + /* + * Silergy SY6288CCAC-GP 2A Power Distribution Switch. + */ compatible = "regulator-fixed"; regulator-name = "USB_VBUS"; @@ -90,11 +99,20 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* + * signal name from the schematics: USB_PWR_EN + */ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; enable-active-high; }; vcc_5v: regulator-vcc5v { + /* + * supplied by the main power input which called PWR_5V_STB + * in the schematics + */ compatible = "regulator-fixed"; regulator-name = "VCC5V"; @@ -102,6 +120,9 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; + /* + * signal name from the schematics: 3V3_5V_EN + */ gpio = <&gpio GPIODV_29 GPIO_ACTIVE_LOW>; regulator-boot-on; @@ -109,12 +130,18 @@ }; vcck: regulator-vcck { + /* + * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz + * Synchronous Step Down Regulator. + */ compatible = "pwm-regulator"; regulator-name = "VCCK"; regulator-min-microvolt = <860000>; regulator-max-microvolt = <1140000>; + vin-supply = <&vcc_5v>; + pwms = <&pwm_cd 0 1148 0>; pwm-dutycycle-range = <100 0>; @@ -123,19 +150,66 @@ }; vcc_1v8: regulator-vcc1v8 { + /* + * ABLIC S-1339D18-M5001-GP + */ compatible = "regulator-fixed"; regulator-name = "VCC1V8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + + vin-supply = <&vcc_3v3>; }; vcc_3v3: regulator-vcc3v3 { + /* + * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz + * Synchronous Step Down Regulator. Also called + * VDDIO_AO3.3V in the schematics. + */ compatible = "regulator-fixed"; regulator-name = "VCC3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + + vin-supply = <&vcc_5v>; + }; + + vcc_ddr3: regulator-vcc-ddr3 { + /* + * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz + * Synchronous Step Down Regulator. Also called + * DDR3_1.5V in the schematics. + */ + compatible = "regulator-fixed"; + + regulator-name = "VCC_DDR3_1V5"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + + vin-supply = <&vcc_5v>; + + regulator-boot-on; + regulator-always-on; + }; + + vcc_rtc: regulator-vcc-rtc { + /* + * Global Mixed-mode Technology Inc. G918T12U-GP + */ + compatible = "regulator-fixed"; + + regulator-name = "VCC_RTC"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + /* + * When the board is powered then the input is VCC3V3, + * otherwise power is taken from the coin cell battery. + */ + vin-supply = <&vcc_3v3>; }; }; @@ -164,6 +238,10 @@ eth_phy0: ethernet-phy@0 { /* IC Plus IP101A/G (0x02430c54) */ reg = <0>; + icplus,select-interrupt; + interrupt-parent = <&gpio_intc>; + /* GPIOH_3 */ + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; }; }; }; @@ -211,6 +289,56 @@ }; }; +&gpio_ao { + gpio-line-names = "Linux_TX", "Linux_RX", + "SLP_S5_N", "USB2_OC_FLAG#", + "HUB_RST", "USB_PWR_EN", + "I2S_IN", "SLP_S1_N", + "TCK", "TMS", "TDI", "TDO", + "HDMI_CEC", "5640_IRQ", + "MUTE", "S805_TEST#"; +}; + +&gpio { + gpio-line-names = /* Bank GPIOX */ + "WIFI_SD_D0", "WIFI_SD_D1", "WIFI_SD_D2", + "WIFI_SD_D3", "BTPCM_DOUT", "BTPCM_DIN", + "BTPCM_SYNC", "BTPCM_CLK", "WIFI_SD_CLK", + "WIFI_SD_CMD", "WIFI_32K", "WIFI_PWREN", + "UART_B_TX", "UART_B_RX", "UART_B_CTS_N", + "UART_B_RTS_N", "BT_EN", "WIFI_WAKE_HOST", + /* Bank GPIOY */ + "", "", "", "", "", "", "", "", "", "", + "", "", + /* Bank GPIODV */ + "VCCK_PWM_C", "I2C_SDA_A", "I2C_SCL_A", + "I2C_SDA_B", "I2C_SCL_B", "VDDEE_PWM_D", + "VDDEE_PWM 3V3_5V_EN", + /* Bank GPIOH */ + "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", + "RMII_IRQ", "RMII_RST#", "RMII_TXD1", + "RMII_TXD0", "AV_select_1", "AV_select_2", + "MCU_Control_S", + /* Bank CARD */ + "SD_D1_B", "SD_D0_B", "SD_CLK_8726MX", + "SD_CMD_8726MX", "SD_D3_B", "SD_D2_B", + "CARD_EN_DET (CARD_DET)", + /* Bank BOOT */ + "NAND_D0 (EMMC)", "NAND_D1 (EMMC)", + "NAND_D2 (EMMC)", "NAND_D3 (EMMC)", + "NAND_D4 (EMMC)", "NAND_D5 (EMMC)", + "NAND_D6 (EMMC)", "NAND_D7 (EMMC)", + "NAND_CS1 (EMMC)", "NAND_CS2 iNAND_RS1 (EMMC)", + "NAND_nR/B iNAND_CMD (EMMC)", "NAND_ALE (EMMC)", + "NAND_CLE (EMMC)", "nRE_S1 NAND_nRE (EMMC)", + "nWE_S1 NAND_nWE (EMMC)", "", "", "SPI_CS", + /* Bank DIF */ + "RMII_RXD1", "RMII_RXD0", "RMII_CRS_DV", + "RMII_50M_IN", "GPIODIF_4", "GPIODIF_5", + "RMII_TXEN", "CPUETH_25MOUT", "RMII_MDC", + "RMII_MDIO"; +}; + &pwm_cd { status = "okay"; pinctrl-0 = <&pwm_c1_pins>; |