diff options
Diffstat (limited to 'arch/arm/boot/dts/omap3-gta04.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/omap3-gta04.dtsi | 50 |
1 files changed, 35 insertions, 15 deletions
diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index ee62d00bcbe6..fb3a69604ed5 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -237,11 +237,18 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; - }; - twl_audio: audio { - compatible = "ti,twl4030-audio"; - codec { + twl_audio: audio { + compatible = "ti,twl4030-audio"; + ti,enable-vibra = <1>; + codec { + ti,ramp_delay_value = <3>; + }; + }; + + twl_power: power { + compatible = "ti,twl4030-power"; + ti,use_poweroff; }; }; }; @@ -257,15 +264,23 @@ compatible = "bosch,bmp085"; reg = <0x77>; interrupt-parent = <&gpio4>; - interrupts = <17 IRQ_TYPE_EDGE_RISING>; + interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* GPIO_113 */ }; /* accelerometer */ bma180@41 { compatible = "bosch,bma180"; reg = <0x41>; - interrupt-parent = <&gpio3>; - interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio4>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */ + }; + + /* gyroscope */ + itg3200@68 { + compatible = "invensense,itg3200"; + reg = <0x68>; + interrupt-parent = <&gpio2>; + interrupts = <24 0>; /* GPIO_56 */ }; /* leds */ @@ -316,7 +331,7 @@ compatible = "ti,tsc2007"; reg = <0x48>; interrupt-parent = <&gpio6>; - interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* GPIO_160 */ gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; ti,x-plate-ohms = <600>; }; @@ -355,12 +370,17 @@ vmmc-supply = <&vaux4>; bus-width = <4>; ti,non-removable; + cap-power-off-card; }; &mmc3 { status = "disabled"; }; +&twl_keypad { + status = "disabled"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; @@ -377,8 +397,8 @@ }; &charger { - bb_uvolt = <3200000>; - bb_uamp = <150>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; }; /* spare */ @@ -412,16 +432,12 @@ regulator-max-microvolt = <3150000>; }; -/* Needed to power the DPI pins */ -&vpll2 { - regulator-always-on; -}; - &dss { pinctrl-names = "default"; pinctrl-0 = < &dss_dpi_pins >; status = "okay"; + vdds_dsi-supply = <&vpll2>; port { dpi_out: endpoint { @@ -498,3 +514,7 @@ }; }; }; + +&mcbsp2 { + status = "okay"; +}; |