summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/omap4-droid4-xt894.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/boot/dts/omap4-droid4-xt894.dts')
-rw-r--r--arch/arm/boot/dts/omap4-droid4-xt894.dts203
1 files changed, 184 insertions, 19 deletions
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
index b21084da490b..bdf73cbcec3a 100644
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -70,8 +70,30 @@
regulator-always-on;
};
- /* HS USB Host PHY on PORT 1 */
- hsusb1_phy: hsusb1_phy {
+ /* FS USB Host PHY on port 1 for mdm6600 */
+ fsusb1_phy: usb-phy@1 {
+ compatible = "motorola,mapphone-mdm6600";
+ pinctrl-0 = <&usb_mdm6600_pins>;
+ pinctrl-names = "default";
+ enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */
+ power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */
+ reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */
+ /* mode: gpio_148 gpio_149 */
+ motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
+ <&gpio5 21 GPIO_ACTIVE_HIGH>;
+ /* cmd: gpio_103 gpio_104 gpio_142 */
+ motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
+ <&gpio4 8 GPIO_ACTIVE_HIGH>,
+ <&gpio5 14 GPIO_ACTIVE_HIGH>;
+ /* status: gpio_52 gpio_53 gpio_55 */
+ motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
+ <&gpio2 21 GPIO_ACTIVE_HIGH>,
+ <&gpio2 23 GPIO_ACTIVE_HIGH>;
+ #phy-cells = <0>;
+ };
+
+ /* HS USB host TLL nop-phy on port 2 for w3glte */
+ hsusb2_phy: usb-phy@2 {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
@@ -117,6 +139,26 @@
};
};
+
+ soundcard {
+ compatible = "audio-graph-card";
+ label = "Droid 4 Audio";
+
+ simple-graph-card,widgets =
+ "Speaker", "Earpiece",
+ "Speaker", "Loudspeaker",
+ "Headphone", "Headphone Jack",
+ "Microphone", "Internal Mic";
+
+ simple-graph-card,routing =
+ "Earpiece", "EP",
+ "Loudspeaker", "SPKR",
+ "Headphone Jack", "HSL",
+ "Headphone Jack", "HSR",
+ "MICR", "Internal Mic";
+
+ dais = <&mcbsp2_port>, <&mcbsp3_port>;
+ };
};
&dss {
@@ -124,13 +166,6 @@
};
&gpio6 {
- touchscreen_reset {
- gpio-hog;
- gpios = <13 0>;
- output-high;
- line-name = "touchscreen-reset";
- };
-
pwm8: dmtimer-pwm-8 {
pinctrl-names = "default";
pinctrl-0 = <&vibrator_direction_pin>;
@@ -362,22 +397,18 @@
};
};
-/*
- * REVISIT: Add gpio173 reset pin handling to the driver, see gpio-hog above.
- * If the GPIO reset is used, we probably need to have /lib/firmware/maxtouch.fw
- * available. See "mxt-app" and "droid4-touchscreen-firmware" tools for more
- * information.
- */
&i2c2 {
- tsp@4a {
+ touchscreen@4a {
compatible = "atmel,maxtouch";
reg = <0x4a>;
pinctrl-names = "default";
pinctrl-0 = <&touchscreen_pins>;
+ reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
+
/* gpio_183 with sys_nirq2 pad as wakeup */
- interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING
- &omap4_pmx_core 0x160>;
+ interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>,
+ <&omap4_pmx_core 0x160>;
interrupt-names = "irq", "wakeup";
wakeup-source;
};
@@ -435,6 +466,7 @@
touchscreen_pins: pinmux_touchscreen_pins {
pinctrl-single,pins = <
+ OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
>;
};
@@ -445,6 +477,43 @@
>;
};
+ usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
+ pinctrl-single,pins = <
+ /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
+ OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
+
+ /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
+ OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
+
+ /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
+ OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
+
+ /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
+ OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
+
+ /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
+ OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
+
+ /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
+ OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
+
+ /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
+ OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
+
+ /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
+ OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
+
+ /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
+ OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+
+ /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
+ OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+
+ /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
+ OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
+ >;
+ };
+
usb_ulpi_pins: pinmux_usb_ulpi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x196, MUX_MODE7)
@@ -484,6 +553,28 @@
>;
};
+ /*
+ * Note that the v3.0.8 stock userspace dynamically remuxes uart1
+ * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
+ * when not used. If needed, we can add rts pin remux later based
+ * on power measurements.
+ */
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
+ OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+ /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
+ OMAP4_IOPAD(0x13e, MUX_MODE1)
+
+ /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
+ OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
+
+ /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
+ OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
+ >;
+ };
+
/* uart3_tx_irtx and uart3_rx_irrx */
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
@@ -512,6 +603,24 @@
OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */
>;
};
+
+ mcbsp2_pins: pinmux_mcbsp2_pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx */
+ OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_dr */
+ OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0) /* abe_mcbsp2_dx */
+ OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx */
+ >;
+ };
+
+ mcbsp3_pins: pinmux_mcbsp3_pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_dr */
+ OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1) /* abe_mcbsp3_dx */
+ OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */
+ OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */
+ >;
+ };
};
&omap4_pmx_wkup {
@@ -535,6 +644,17 @@
};
};
+/*
+ * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
+ * uart1 wakeirq.
+ */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
+ &omap4_pmx_core 0xfc>;
+};
+
&uart3 {
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core 0x17c>;
@@ -551,8 +671,13 @@
};
};
+&usbhsohci {
+ phys = <&fsusb1_phy>;
+ phy-names = "usb";
+};
+
&usbhsehci {
- phys = <&hsusb1_phy>;
+ phys = <&hsusb2_phy>;
};
&usbhshost {
@@ -597,3 +722,43 @@
"0", "0", "1";
};
};
+
+&mcbsp2 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp2_pins>;
+ status = "okay";
+
+ mcbsp2_port: port {
+ cpu_dai2: endpoint {
+ dai-format = "i2s";
+ remote-endpoint = <&cpcap_audio_codec0>;
+ frame-master = <&cpcap_audio_codec0>;
+ bitclock-master = <&cpcap_audio_codec0>;
+ };
+ };
+};
+
+&mcbsp3 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp3_pins>;
+ status = "okay";
+
+ mcbsp3_port: port {
+ cpu_dai3: endpoint {
+ dai-format = "dsp_a";
+ frame-master = <&cpcap_audio_codec1>;
+ bitclock-master = <&cpcap_audio_codec1>;
+ remote-endpoint = <&cpcap_audio_codec1>;
+ };
+ };
+};
+
+&cpcap_audio_codec0 {
+ remote-endpoint = <&cpu_dai2>;
+};
+
+&cpcap_audio_codec1 {
+ remote-endpoint = <&cpu_dai3>;
+};
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 10:22:15 +0100