diff options
Diffstat (limited to 'arch/arm/boot/dts/omap5-cm-t54.dts')
| -rw-r--r-- | arch/arm/boot/dts/omap5-cm-t54.dts | 277 |
1 files changed, 272 insertions, 5 deletions
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts index b8698ca68647..b54b271e153b 100644 --- a/arch/arm/boot/dts/omap5-cm-t54.dts +++ b/arch/arm/boot/dts/omap5-cm-t54.dts @@ -16,6 +16,12 @@ reg = <0x80000000 0x7F000000>; /* 2048 MB */ }; + aliases { + display0 = &hdmi0; + display1 = &dvi0; + display2 = &lcd0; + }; + vmmcsd_fixed: fixed-regulator-mmcsd { compatible = "regulator-fixed"; regulator-name = "vmmcsd_fixed"; @@ -45,6 +51,13 @@ enable-active-high; }; + ads7846reg: ads7846-reg { + compatible = "regulator-fixed"; + regulator-name = "ads7846-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; @@ -66,6 +79,105 @@ default-state = "off"; }; }; + + lcd0: display { + compatible = "startek,startek-kd050c", "panel-dpi"; + label = "lcd"; + + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + + enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>; + + panel-timing { + clock-frequency = <33000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <43>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_lcd_out>; + }; + }; + }; + + hdmi0: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_conn_pins>; + + hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; + + tfp410: encoder@0 { + compatible = "ti,tfp410"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_dvi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector@1 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c2>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; +}; + +&omap5_pmx_wkup { + + ads7846_pins: pinmux_ads7846_pins { + pinctrl-single,pins = < + 0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ + >; + }; }; &omap5_pmx_core { @@ -88,6 +200,13 @@ >; }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */ @@ -127,8 +246,8 @@ wlan_gpios_pins: pinmux_wlan_gpios_pins { pinctrl-single,pins = < - OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */ - OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */ + OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */ + OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */ >; }; @@ -144,6 +263,104 @@ OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ >; }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */ + OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */ + OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */ + >; + }; + + lcd_pins: pinmux_lcd_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */ + >; + }; + + hdmi_conn_pins: pinmux_hdmi_conn_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */ + OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */ + OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */ + OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */ + OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */ + OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */ + OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */ + OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */ + OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */ + OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */ + OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */ + OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */ + OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */ + OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */ + OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */ + OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */ + OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */ + OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */ + OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */ + OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */ + OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */ + OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */ + OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */ + OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */ + OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */ + OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */ + OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */ + OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */ + >; + }; + + mcspi2_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */ + OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */ + >; + }; +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; + + /* touch controller */ + ads7846@0 { + pinctrl-names = "default"; + pinctrl-0 = <&ads7846_pins>; + + compatible = "ti,ads7846"; + vcc-supply = <&ads7846reg>; + + reg = <0>; /* CS0 */ + spi-max-frequency = <1500000>; + + interrupt-parent = <&gpio1>; + interrupts = <15 0>; /* gpio1_wk15 */ + pendown-gpio = <&gpio1 15 0>; + + + ti,x-min = /bits/ 16 <0x0>; + ti,x-max = /bits/ 16 <0x0fff>; + ti,y-min = /bits/ 16 <0x0>; + ti,y-max = /bits/ 16 <0x0fff>; + + ti,x-plate-ohms = /bits/ 16 <180>; + ti,pressure-max = /bits/ 16 <255>; + + ti,debounce-max = /bits/ 16 <30>; + ti,debounce-tol = /bits/ 16 <10>; + ti,debounce-rep = /bits/ 16 <1>; + + linux,wakeup; + }; }; &mmc1 { @@ -353,13 +570,12 @@ }; ldo8_reg: ldo8 { - /* VDD_3v0: Does not go anywhere */ + /* VDD_3V_GP: act led/serial console */ regulator-name = "ldo8"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; + regulator-always-on; regulator-boot-on; - /* Unused */ - status = "disabled"; }; ldo9_reg: ldo9 { @@ -399,6 +615,13 @@ }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + &usbhshost { port2-mode = "ehci-hsic"; port3-mode = "ehci-hsic"; @@ -408,6 +631,50 @@ phys = <0 &hsusb2_phy &hsusb3_phy>; }; +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + &cpu0 { cpu0-supply = <&smps123_reg>; }; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_dvi_out: endpoint@0 { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + + dpi_lcd_out: endpoint@1 { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; + }; +}; + +&dsi2 { + status = "ok"; + vdd-supply = <&ldo4_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo4_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + lanes = <1 0 3 2 5 4 7 6>; + }; + }; +}; |