1 files changed, 79 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
new file mode 100644
index 000000000000..3340fc3f0739
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-edgeble-neu2.dtsi"
+
+/ {
+	model = "Edgeble Neu2 IO Board";
+	compatible = "edgeble,neural-compute-module-2-io",
+		     "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+};
+
+&gmac {
+	assigned-clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>,
+			  <&cru CLK_GMAC_ETHERNET_OUT>;
+	assigned-clock-parents = <&cru CLK_GMAC_SRC_M1>, <&cru RGMII_MODE_CLK>;
+	assigned-clock-rates = <125000000>, <0>, <25000000>;
+	clock_in_out = "input";
+	phy-handle = <&phy>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins &clk_out_ethernetm1_pins>;
+	tx_delay = <0x2a>;
+	rx_delay = <0x1a>;
+	status = "okay";
+};
+
+&mdio {
+	phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c916",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	ethernet {
+		eth_phy_rst: eth-phy-rst {
+			rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr104;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};