diff options
Diffstat (limited to 'arch/arm/boot/dts')
| -rw-r--r-- | arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi | 73 | ||||
| -rw-r--r-- | arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 70 |
2 files changed, 70 insertions, 73 deletions
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi index de6acee738e5..b9b85ffc142d 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi @@ -8,7 +8,7 @@ / { soc { i2c@80128000 { - lsm303dlh@18 { + accelerometer@18 { /* Accelerometer */ compatible = "st,lsm303dlh-accel"; st,drdy-int-pin = <1>; @@ -30,7 +30,7 @@ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; */ }; - lsm303dlh@1e { + magnetometer@1e { /* Magnetometer */ compatible = "st,lsm303dlh-magn"; reg = <0x1e>; @@ -48,7 +48,7 @@ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; */ }; - lis331dl@1c { + accelerometer@1c { /* Accelerometer */ compatible = "st,lis331dl-accel"; st,drdy-int-pin = <1>; @@ -62,6 +62,46 @@ interrupts = <18 IRQ_TYPE_EDGE_RISING>, <19 IRQ_TYPE_EDGE_RISING>; }; + magnetometer@f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + dvdd-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; + */ + }; + gyroscope@68 { + /* Gyroscope */ + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x68>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupts-extended = + <&gpio1 0 IRQ_TYPE_EDGE_RISING>, + <&gpio0 31 IRQ_TYPE_EDGE_RISING>; + }; + pressure@5c { + /* Barometer/pressure sensor */ + compatible = "st,lps001wp-press"; + reg = <0x5c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; }; i2c@80110000 { synaptics@4b { @@ -102,6 +142,33 @@ }; }; pinctrl { + accelerometer { + accel_tvk_mode: accel_tvk { + /* Accelerometer interrupt lines 1 & 2 */ + tvk_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + gyroscope { + /* + * These lines are shared between Gyroscope l3g400dh + * and AK8974 magnetometer. + */ + gyro_magn_tvk_mode: gyro_magn_tvk { + /* GPIO 31 used for INT pull down the line */ + tvk_cfg1 { + pins = "GPIO31_V3"; + ste,config = <&gpio_in_pd>; + }; + /* GPIO 32 used for DRDY, pull this down */ + tvk_cfg2 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; synaptics { synaptics_tvk_mode: synaptics_tvk { /* Touchscreen uses GPIO 84 */ diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 34b9f434b4b7..aa68224560f6 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -81,49 +81,6 @@ }; }; }; - /* Sensors mounted on all board variants */ - i2c@80128000 { - ak8974@f { - /* Magnetometer */ - compatible = "asahi-kasei,ak8974"; - reg = <0x0f>; - avdd-supply = <&ab8500_ldo_aux1_reg>; - dvdd-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; - */ - }; - l3g4200d@68 { - /* Gyroscope */ - compatible = "st,l3g4200d-gyro"; - st,drdy-int-pin = <2>; - reg = <0x68>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - interrupts-extended = - <&gpio1 0 IRQ_TYPE_EDGE_RISING>, - <&gpio0 31 IRQ_TYPE_EDGE_RISING>; - }; - lsp001wm@5c { - /* Barometer/pressure sensor */ - compatible = "st,lps001wp-press"; - reg = <0x5c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - }; - }; pinctrl { /* Pull up this GPIO pin */ @@ -151,33 +108,6 @@ }; }; }; - accelerometer { - accel_tvk_mode: accel_tvk { - /* Accelerometer interrupt lines 1 & 2 */ - tvk_cfg { - pins = "GPIO82_C1", "GPIO83_D3"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - gyroscope { - /* - * These lines are shared between Gyroscope l3g400dh - * and AK8974 magnetometer. - */ - gyro_magn_tvk_mode: gyro_magn_tvk { - /* GPIO 31 used for INT pull down the line */ - tvk_cfg1 { - pins = "GPIO31_V3"; - ste,config = <&gpio_in_pd>; - }; - /* GPIO 32 used for DRDY, pull this down */ - tvk_cfg2 { - pins = "GPIO32_V2"; - ste,config = <&gpio_in_pd>; - }; - }; - }; }; }; }; |