1 files changed, 136 insertions, 0 deletions
diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c
new file mode 100644
index 000000000000..831e4a56cae1
--- /dev/null
+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -0,0 +1,136 @@
+/*
+ * arch/arm/mach-kirkwood/sheevaplug-setup.c
+ *
+ * Marvell SheevaPlug Reference Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include <plat/orion_nand.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition sheevaplug_nand_parts[] = {
+	{
+		.name = "u-boot",
+		.offset = 0,
+		.size = SZ_1M
+	}, {
+		.name = "uImage",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size = SZ_4M
+	}, {
+		.name = "root",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size = MTDPART_SIZ_FULL
+	},
+};
+
+static struct resource sheevaplug_nand_resource = {
+	.flags		= IORESOURCE_MEM,
+	.start		= KIRKWOOD_NAND_MEM_PHYS_BASE,
+	.end		= KIRKWOOD_NAND_MEM_PHYS_BASE +
+			  KIRKWOOD_NAND_MEM_SIZE - 1,
+};
+
+static struct orion_nand_data sheevaplug_nand_data = {
+	.parts		= sheevaplug_nand_parts,
+	.nr_parts	= ARRAY_SIZE(sheevaplug_nand_parts),
+	.cle		= 0,
+	.ale		= 1,
+	.width		= 8,
+	.chip_delay	= 25,
+};
+
+static struct platform_device sheevaplug_nand_flash = {
+	.name		= "orion_nand",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &sheevaplug_nand_data,
+	},
+	.resource	= &sheevaplug_nand_resource,
+	.num_resources	= 1,
+};
+
+static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
+	// unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led sheevaplug_led_pins[] = {
+	{
+		.name			= "plug:green:health",
+		.default_trigger	= "default-on",
+		.gpio			= 49,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data sheevaplug_led_data = {
+	.leds		= sheevaplug_led_pins,
+	.num_leds	= ARRAY_SIZE(sheevaplug_led_pins),
+};
+
+static struct platform_device sheevaplug_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &sheevaplug_led_data,
+	}
+};
+
+static unsigned int sheevaplug_mpp_config[] __initdata = {
+	MPP29_GPIO,	/* USB Power Enable */
+	MPP49_GPIO,	/* LED */
+	0
+};
+
+static void __init sheevaplug_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_init();
+	kirkwood_mpp_conf(sheevaplug_mpp_config);
+
+	kirkwood_uart0_init();
+
+	if (gpio_request(29, "USB Power Enable") != 0 ||
+	    gpio_direction_output(29, 1) != 0)
+		printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+	kirkwood_ehci_init();
+
+	kirkwood_ge00_init(&sheevaplug_ge00_data);
+	kirkwood_sdio_init(&sheevaplug_mvsdio_data);
+
+	platform_device_register(&sheevaplug_nand_flash);
+	platform_device_register(&sheevaplug_leds);
+}
+
+MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
+	/* Maintainer: shadi Ammouri <shadi@marvell.com> */
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= sheevaplug_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END