diff options
Diffstat (limited to 'arch/arm/mach-omap1/board-perseus2.c')
| -rw-r--r-- | arch/arm/mach-omap1/board-perseus2.c | 75 |
1 files changed, 36 insertions, 39 deletions
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c index 67acd4142639..6ed649b8b8d3 100644 --- a/arch/arm/mach-omap1/board-perseus2.c +++ b/arch/arm/mach-omap1/board-perseus2.c @@ -265,6 +265,39 @@ static void __init perseus2_init_smc91x(void) static void __init omap_perseus2_init(void) { + /* Early, board-dependent init */ + + /* + * Hold GSM Reset until needed + */ + omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL); + + /* + * UARTs -> done automagically by 8250 driver + */ + + /* + * CSx timings, GPIO Mux ... setup + */ + + /* Flash: CS0 timings setup */ + omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0); + omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0); + + /* + * Ethernet support through the debug board + * CS1 timings setup + */ + omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1); + omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1); + + /* + * Configure MPU_EXT_NIRQ IO in IO_CONF9 register, + * It is used as the Ethernet controller interrupt + */ + omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, + OMAP7XX_IO_CONF_9); + perseus2_init_smc91x(); if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0) @@ -294,11 +327,6 @@ static void __init omap_perseus2_init(void) omap_register_i2c_bus(1, 100, NULL, 0); } -static void __init omap_perseus2_init_irq(void) -{ - omap1_init_common_hw(); - omap1_init_irq(); -} /* Only FPGA needs to be mapped here. All others are done with ioremap */ static struct map_desc omap_perseus2_io_desc[] __initdata = { { @@ -311,49 +339,18 @@ static struct map_desc omap_perseus2_io_desc[] __initdata = { static void __init omap_perseus2_map_io(void) { - omap1_map_common_io(); + omap7xx_map_io(); iotable_init(omap_perseus2_io_desc, ARRAY_SIZE(omap_perseus2_io_desc)); - - /* Early, board-dependent init */ - - /* - * Hold GSM Reset until needed - */ - omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL); - - /* - * UARTs -> done automagically by 8250 driver - */ - - /* - * CSx timings, GPIO Mux ... setup - */ - - /* Flash: CS0 timings setup */ - omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0); - omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0); - - /* - * Ethernet support through the debug board - * CS1 timings setup - */ - omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1); - omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1); - - /* - * Configure MPU_EXT_NIRQ IO in IO_CONF9 register, - * It is used as the Ethernet controller interrupt - */ - omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9); } MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2") /* Maintainer: Kevin Hilman <kjh@hilman.org> */ .boot_params = 0x10000100, .map_io = omap_perseus2_map_io, + .init_early = omap1_init_early, .reserve = omap_reserve, - .init_irq = omap_perseus2_init_irq, + .init_irq = omap1_init_irq, .init_machine = omap_perseus2_init, .timer = &omap1_timer, MACHINE_END |