1 files changed, 122 insertions, 13 deletions

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 5babce497415..67d9c634c05d 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -17,6 +17,7 @@
 #include <linux/gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl022.h>
+#include <linux/amba/serial.h>
 #include <linux/spi/spi.h>
 #include <linux/mfd/ab8500.h>
 #include <linux/mfd/tc3589x.h>
@@ -29,12 +30,14 @@
 
 #include <plat/pincfg.h>
 #include <plat/i2c.h>
+#include <plat/ste_dma40.h>
 
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
 #include <mach/irqs.h>
 
+#include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
 #include "pins-db8500.h"
 #include "board-mop500.h"
@@ -123,16 +126,6 @@ struct platform_device ab8500_device = {
 	.resource = ab8500_resources,
 };
 
-static struct pl022_ssp_controller ssp0_platform_data = {
-	.bus_id = 0,
-	/* pl022 not yet supports dma */
-	.enable_dma = 0,
-	/* on this platform, gpio 31,142,144,214 &
-	 * 224 are connected as chip selects
-	 */
-	.num_chipselect = 5,
-};
-
 /*
  * TC35892
  */
@@ -319,16 +312,132 @@ static struct platform_device *platform_devs[] __initdata = {
 	&mop500_gpio_keys_device,
 };
 
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV8_SSP0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV8_SSP0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+	.bus_id = 0,
+#ifdef CONFIG_STE_DMA40
+	.enable_dma = 1,
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &ssp0_dma_cfg_rx,
+	.dma_tx_param = &ssp0_dma_cfg_tx,
+#else
+	.enable_dma = 0,
+#endif
+	/* on this platform, gpio 31,142,144,214 &
+	 * 224 are connected as chip selects
+	 */
+	.num_chipselect = 5,
+};
+
 static void __init mop500_spi_init(void)
 {
 	db8500_add_ssp0(&ssp0_platform_data);
 }
 
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV13_UART0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV13_UART0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV12_UART1_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV12_UART1_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV11_UART2_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV11_UART2_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct amba_pl011_data uart0_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart0_dma_cfg_rx,
+	.dma_tx_param = &uart0_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart1_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart1_dma_cfg_rx,
+	.dma_tx_param = &uart1_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart2_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart2_dma_cfg_rx,
+	.dma_tx_param = &uart2_dma_cfg_tx,
+#endif
+};
+
 static void __init mop500_uart_init(void)
 {
-	db8500_add_uart0();
-	db8500_add_uart1();
-	db8500_add_uart2();
+	db8500_add_uart0(&uart0_plat);
+	db8500_add_uart1(&uart1_plat);
+	db8500_add_uart2(&uart2_plat);
 }
 
 static void __init u8500_init_machine(void)