diff options
Diffstat (limited to 'arch/avr32/boards/atstk1000/Kconfig')
| -rw-r--r-- | arch/avr32/boards/atstk1000/Kconfig | 109 |
1 files changed, 0 insertions, 109 deletions
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig deleted file mode 100644 index 8dc48214f0b7..000000000000 --- a/arch/avr32/boards/atstk1000/Kconfig +++ /dev/null @@ -1,109 +0,0 @@ -# STK1000 customization - -if BOARD_ATSTK1000 - -choice - prompt "ATSTK1000 CPU daughterboard type" - default BOARD_ATSTK1002 - -config BOARD_ATSTK1002 - bool "ATSTK1002" - select CPU_AT32AP7000 - -config BOARD_ATSTK1003 - bool "ATSTK1003" - select CPU_AT32AP7001 - -config BOARD_ATSTK1004 - bool "ATSTK1004" - select CPU_AT32AP7002 - -config BOARD_ATSTK1006 - bool "ATSTK1006" - select CPU_AT32AP7000 - -endchoice - - -config BOARD_ATSTK100X_CUSTOM - bool "Non-default STK1002/STK1003/STK1004 jumper settings" - help - You will normally leave the jumpers on the CPU card at their - default settings. If you need to use certain peripherals, - you will need to change some of those jumpers. - -if BOARD_ATSTK100X_CUSTOM - -config BOARD_ATSTK100X_SW1_CUSTOM - bool "SW1: use SSC1 (not SPI0)" - help - This also prevents using the external DAC as an audio interface, - and means you can't initialize the on-board QVGA display. - -config BOARD_ATSTK100X_SW2_CUSTOM - bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" - help - If you change this you'll want an updated boot loader putting - the console on UART-C not UART-A. - -config BOARD_ATSTK100X_SW3_CUSTOM - bool "SW3: use TIMER1 (not SSC0 and GCLK)" - help - This also prevents using the external DAC as an audio interface. - -config BOARD_ATSTK100X_SW4_CUSTOM - bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" - help - To use the camera interface you'll need a custom card (on the - PCI-format connector) connect a video sensor. - -config BOARD_ATSTK1002_SW5_CUSTOM - bool "SW5: use MACB1 (not LCDC)" - depends on BOARD_ATSTK1002 - -config BOARD_ATSTK1002_SW6_CUSTOM - bool "SW6: more GPIOs (not MACB0)" - depends on BOARD_ATSTK1002 - -endif # custom - -config BOARD_ATSTK100X_SPI1 - bool "Configure SPI1 controller" - depends on !BOARD_ATSTK100X_SW4_CUSTOM - help - All the signals for the second SPI controller are available on - GPIO lines and accessed through the J1 jumper block. Say "y" - here to configure that SPI controller. - -config BOARD_ATSTK1000_J2_LED - bool - default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB - -choice - prompt "LEDs connected to J2:" - depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM - optional - help - Select this if you have jumpered the J2 jumper block to the - LED0..LED7 amber leds, or to the RGB leds, using a ten-pin - IDC cable. A default "heartbeat" trigger is provided, but - you can of course override this. - -config BOARD_ATSTK1000_J2_LED8 - bool "LED0..LED7" - help - Select this if J2 is jumpered to LED0..LED7 amber leds. - -config BOARD_ATSTK1000_J2_RGB - bool "RGB leds" - help - Select this if J2 is jumpered to the RGB leds. - -endchoice - -config BOARD_ATSTK1000_EXTDAC - bool - depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM - default y - -endif # stk 1000 |