diff options
Diffstat (limited to 'arch/cris/arch-v32/mach-a3/Kconfig')
| -rw-r--r-- | arch/cris/arch-v32/mach-a3/Kconfig | 111 |
1 files changed, 0 insertions, 111 deletions
diff --git a/arch/cris/arch-v32/mach-a3/Kconfig b/arch/cris/arch-v32/mach-a3/Kconfig deleted file mode 100644 index 7b63755544dd..000000000000 --- a/arch/cris/arch-v32/mach-a3/Kconfig +++ /dev/null @@ -1,111 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -if CRIS_MACH_ARTPEC3 - -menu "Artpec-3 options" - depends on CRIS_MACH_ARTPEC3 - -config ETRAX_DRAM_VIRTUAL_BASE - hex - default "c0000000" - -config ETRAX_L2CACHE - bool - default y - -config ETRAX_SERIAL_PORTS - int - default 5 - -config ETRAX_DDR2_MRS - hex "DDR2 MRS" - default "0" - -config ETRAX_DDR2_TIMING - hex "DDR2 SDRAM timing" - default "0" - help - SDRAM timing parameters. - -config ETRAX_DDR2_CONFIG - hex "DDR2 config" - default "0" - -config ETRAX_DDR2_LATENCY - hex "DDR2 latency" - default "0" - -config ETRAX_PIO_CE0_CFG - hex "PIO CE0 configuration" - default "0" - -config ETRAX_PIO_CE1_CFG - hex "PIO CE1 configuration" - default "0" - -config ETRAX_PIO_CE2_CFG - hex "PIO CE2 configuration" - default "0" - -config ETRAX_DEF_GIO_PA_OE - hex "GIO_PA_OE" - default "00000000" - help - Configures the direction of general port A bits. 1 is out, 0 is in. - This is often totally different depending on the product used. - There are some guidelines though - if you know that only LED's are - connected to port PA, then they are usually connected to bits 2-4 - and you can therefore use 1c. On other boards which don't have the - LED's at the general ports, these bits are used for all kinds of - stuff. If you don't know what to use, it is always safe to put all - as inputs, although floating inputs isn't good. - -config ETRAX_DEF_GIO_PA_OUT - hex "GIO_PA_OUT" - default "00000000" - help - Configures the initial data for the general port A bits. Most - products should use 00 here. - -config ETRAX_DEF_GIO_PB_OE - hex "GIO_PB_OE" - default "000000000" - help - Configures the direction of general port B bits. 1 is out, 0 is in. - This is often totally different depending on the product used. - There are some guidelines though - if you know that only LED's are - connected to port PA, then they are usually connected to bits 2-4 - and you can therefore use 1c. On other boards which don't have the - LED's at the general ports, these bits are used for all kinds of - stuff. If you don't know what to use, it is always safe to put all - as inputs, although floating inputs isn't good. - -config ETRAX_DEF_GIO_PB_OUT - hex "GIO_PB_OUT" - default "000000000" - help - Configures the initial data for the general port B bits. Most - products should use 00000 here. - -config ETRAX_DEF_GIO_PC_OE - hex "GIO_PC_OE" - default "00000" - help - Configures the direction of general port C bits. 1 is out, 0 is in. - This is often totally different depending on the product used. - There are some guidelines though - if you know that only LED's are - connected to port PA, then they are usually connected to bits 2-4 - and you can therefore use 1c. On other boards which don't have the - LED's at the general ports, these bits are used for all kinds of - stuff. If you don't know what to use, it is always safe to put all - as inputs, although floating inputs isn't good. - -config ETRAX_DEF_GIO_PC_OUT - hex "GIO_PC_OUT" - default "00000" - help - Configures the initial data for the general port C bits. Most - products should use 00000 here. - -endmenu - -endif |