diff options
Diffstat (limited to 'arch/cris/include/uapi/asm/etraxgpio.h')
| -rw-r--r-- | arch/cris/include/uapi/asm/etraxgpio.h | 157 |
1 files changed, 0 insertions, 157 deletions
diff --git a/arch/cris/include/uapi/asm/etraxgpio.h b/arch/cris/include/uapi/asm/etraxgpio.h index 461c089db765..c6e7d57c8b24 100644 --- a/arch/cris/include/uapi/asm/etraxgpio.h +++ b/arch/cris/include/uapi/asm/etraxgpio.h @@ -11,26 +11,6 @@ * g1-g7 and g25-g31 is both input and outputs but on different pins * Also note that some bits change pins depending on what interfaces * are enabled. - * - * For ETRAX FS (CONFIG_ETRAXFS): - * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction - * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction - * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction - * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction - * /dev/gpioe minor 5, 18 bit GPIO, each bit can change direction - * /dev/leds minor 2, Access to leds depending on kernelconfig - * - * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3): - * /dev/gpioa minor 0, 32 bit GPIO, each bit can change direction - * /dev/gpiob minor 1, 32 bit GPIO, each bit can change direction - * /dev/gpioc minor 3, 16 bit GPIO, each bit can change direction - * /dev/gpiod minor 4, 32 bit GPIO, input only - * /dev/leds minor 2, Access to leds depending on kernelconfig - * /dev/pwm0 minor 16, PWM channel 0 on PA30 - * /dev/pwm1 minor 17, PWM channel 1 on PA31 - * /dev/pwm2 minor 18, PWM channel 2 on PB26 - * /dev/ppwm minor 19, PPWM channel - * */ #ifndef _ASM_ETRAXGPIO_H #define _ASM_ETRAXGPIO_H @@ -40,52 +20,12 @@ #define ETRAXGPIO_IOCTYPE 43 /* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */ -#ifdef CONFIG_ETRAX_ARCH_V10 #define GPIO_MINOR_A 0 #define GPIO_MINOR_B 1 #define GPIO_MINOR_LEDS 2 #define GPIO_MINOR_G 3 #define GPIO_MINOR_LAST 3 #define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST -#endif - -#ifdef CONFIG_ETRAXFS -#define GPIO_MINOR_A 0 -#define GPIO_MINOR_B 1 -#define GPIO_MINOR_LEDS 2 -#define GPIO_MINOR_C 3 -#define GPIO_MINOR_D 4 -#define GPIO_MINOR_E 5 -#ifdef CONFIG_ETRAX_VIRTUAL_GPIO -#define GPIO_MINOR_V 6 -#define GPIO_MINOR_LAST 6 -#else -#define GPIO_MINOR_LAST 5 -#endif -#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST -#endif - -#ifdef CONFIG_CRIS_MACH_ARTPEC3 -#define GPIO_MINOR_A 0 -#define GPIO_MINOR_B 1 -#define GPIO_MINOR_LEDS 2 -#define GPIO_MINOR_C 3 -#define GPIO_MINOR_D 4 -#ifdef CONFIG_ETRAX_VIRTUAL_GPIO -#define GPIO_MINOR_V 6 -#define GPIO_MINOR_LAST 6 -#else -#define GPIO_MINOR_LAST 4 -#endif -#define GPIO_MINOR_FIRST_PWM 16 -#define GPIO_MINOR_PWM0 (GPIO_MINOR_FIRST_PWM+0) -#define GPIO_MINOR_PWM1 (GPIO_MINOR_FIRST_PWM+1) -#define GPIO_MINOR_PWM2 (GPIO_MINOR_FIRST_PWM+2) -#define GPIO_MINOR_PPWM (GPIO_MINOR_FIRST_PWM+3) -#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PPWM -#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST_PWM -#endif - /* supported ioctl _IOC_NR's */ @@ -139,101 +79,4 @@ #define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */ /* *arg updated with current output pins. */ -/* The following ioctl's are applicable to the PWM channels only */ - -#define IO_PWM_SET_MODE 0x20 - -enum io_pwm_mode { - PWM_OFF = 0, /* disabled, deallocated */ - PWM_STANDARD = 1, /* 390 kHz, duty cycle 0..255/256 */ - PWM_FAST = 2, /* variable freq, w/ 10ns active pulse len */ - PWM_VARFREQ = 3, /* individually configurable high/low periods */ - PWM_SOFT = 4 /* software generated */ -}; - -struct io_pwm_set_mode { - enum io_pwm_mode mode; -}; - -/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns - * from 10ns (value = 0) to 81920ns (value = 8191) - * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to - * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty - * cycle (81920 + 10ns or 10ns + 81920ns, respectively).) - */ -#define IO_PWM_SET_PERIOD 0x21 - -struct io_pwm_set_period { - unsigned int lo; /* 0..8191 */ - unsigned int hi; /* 0..8191 */ -}; - -/* Only for modes PWM_STANDARD and PWM_FAST. - * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from - * 0 (value = 0) to 255/256 (value = 255). - * For PWM_FAST, set duty cycle of PWM output signal from - * 0% (value = 0) to 100% (value = 255). Output signal in this mode - * is a 10ns pulse surrounded by a high or low level depending on duty - * cycle (except for 0% and 100% which result in a constant output). - * Resulting output frequency varies from 50 MHz at 50% duty cycle, - * down to 390 kHz at min/max duty cycle. - */ -#define IO_PWM_SET_DUTY 0x22 - -struct io_pwm_set_duty { - int duty; /* 0..255 */ -}; - -/* Returns information about the latest PWM pulse. - * lo: Length of the latest low period, in units of 10ns. - * hi: Length of the latest high period, in units of 10ns. - * cnt: Time since last detected edge, in units of 10ns. - * - * The input source to PWM is decied by IO_PWM_SET_INPUT_SRC. - * - * NOTE: All PWM devices is connected to the same input source. - */ -#define IO_PWM_GET_PERIOD 0x23 - -struct io_pwm_get_period { - unsigned int lo; - unsigned int hi; - unsigned int cnt; -}; - -/* Sets the input source for the PWM input. For the src value see the - * register description for gio:rw_pwm_in_cfg. - * - * NOTE: All PWM devices is connected to the same input source. - */ -#define IO_PWM_SET_INPUT_SRC 0x24 -struct io_pwm_set_input_src { - unsigned int src; /* 0..7 */ -}; - -/* Sets the duty cycles in steps of 1/256, 0 = 0%, 255 = 100% duty cycle */ -#define IO_PPWM_SET_DUTY 0x25 - -struct io_ppwm_set_duty { - int duty; /* 0..255 */ -}; - -/* Configuraton struct for the IO_PWMCLK_SET_CONFIG ioctl to configure - * PWM capable gpio pins: - */ -#define IO_PWMCLK_SETGET_CONFIG 0x26 -struct gpio_pwmclk_conf { - unsigned int gpiopin; /* The pin number based on the opened device */ - unsigned int baseclk; /* The base clock to use, or sw will select one close*/ - unsigned int low; /* The number of low periods of the baseclk */ - unsigned int high; /* The number of high periods of the baseclk */ -}; - -/* Examples: - * To get a symmetric 12 MHz clock without knowing anything about the hardware: - * baseclk = 12000000, low = 0, high = 0 - * To just get info of current setting: - * baseclk = 0, low = 0, high = 0, the values will be updated by driver. - */ - #endif |