diff options
Diffstat (limited to 'arch/mips/alchemy/common')
| -rw-r--r-- | arch/mips/alchemy/common/Makefile | 3 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/dbdma.c | 46 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/gpioint.c | 411 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/gpiolib.c | 42 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/platform.c | 31 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/power.c | 3 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/sleeper.S | 73 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/time.c | 1 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/vss.c | 84 |
9 files changed, 691 insertions, 3 deletions
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile index 811ece7b22e3..d3f5c5137804 100644 --- a/arch/mips/alchemy/common/Makefile +++ b/arch/mips/alchemy/common/Makefile @@ -6,9 +6,10 @@ # obj-y += prom.o time.o clocks.o platform.o power.o setup.o \ - sleeper.o dma.o dbdma.o + sleeper.o dma.o dbdma.o vss.o obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o +obj-$(CONFIG_ALCHEMY_GPIOINT_AU1300) += gpioint.o # optional gpiolib support ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),) diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c index 0e63ee487d6d..c723ec1d3b2c 100644 --- a/arch/mips/alchemy/common/dbdma.c +++ b/arch/mips/alchemy/common/dbdma.c @@ -148,6 +148,50 @@ static dbdev_tab_t au1200_dbdev_tab[] __initdata = { { DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, }; +static dbdev_tab_t au1300_dbdev_tab[] __initdata = { + { AU1300_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8, 0x10100004, 0, 0 }, + { AU1300_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN, 0, 8, 0x10100000, 0, 0 }, + { AU1300_DSCR_CMD0_UART1_TX, DEV_FLAGS_OUT, 0, 8, 0x10101004, 0, 0 }, + { AU1300_DSCR_CMD0_UART1_RX, DEV_FLAGS_IN, 0, 8, 0x10101000, 0, 0 }, + { AU1300_DSCR_CMD0_UART2_TX, DEV_FLAGS_OUT, 0, 8, 0x10102004, 0, 0 }, + { AU1300_DSCR_CMD0_UART2_RX, DEV_FLAGS_IN, 0, 8, 0x10102000, 0, 0 }, + { AU1300_DSCR_CMD0_UART3_TX, DEV_FLAGS_OUT, 0, 8, 0x10103004, 0, 0 }, + { AU1300_DSCR_CMD0_UART3_RX, DEV_FLAGS_IN, 0, 8, 0x10103000, 0, 0 }, + + { AU1300_DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8, 0x10600000, 0, 0 }, + { AU1300_DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN, 4, 8, 0x10600004, 0, 0 }, + { AU1300_DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 8, 8, 0x10601000, 0, 0 }, + { AU1300_DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN, 8, 8, 0x10601004, 0, 0 }, + + { AU1300_DSCR_CMD0_AES_RX, DEV_FLAGS_IN , 4, 32, 0x10300008, 0, 0 }, + { AU1300_DSCR_CMD0_AES_TX, DEV_FLAGS_OUT, 4, 32, 0x10300004, 0, 0 }, + + { AU1300_DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0001c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN, 0, 16, 0x10a0001c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC1_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0101c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN, 0, 16, 0x10a0101c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC2_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0201c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC2_RX, DEV_FLAGS_IN, 0, 16, 0x10a0201c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC3_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0301c, 0, 0 }, + { AU1300_DSCR_CMD0_PSC3_RX, DEV_FLAGS_IN, 0, 16, 0x10a0301c, 0, 0 }, + + { AU1300_DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, + { AU1300_DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, + + { AU1300_DSCR_CMD0_SDMS_TX2, DEV_FLAGS_OUT, 4, 8, 0x10602000, 0, 0 }, + { AU1300_DSCR_CMD0_SDMS_RX2, DEV_FLAGS_IN, 4, 8, 0x10602004, 0, 0 }, + + { AU1300_DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, + + { AU1300_DSCR_CMD0_UDMA, DEV_FLAGS_ANYUSE, 0, 32, 0x14001810, 0, 0 }, + + { AU1300_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 }, + { AU1300_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 }, + + { DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, + { DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, +}; + /* 32 predefined plus 32 custom */ #define DBDEV_TAB_SIZE 64 @@ -1038,6 +1082,8 @@ static int __init alchemy_dbdma_init(void) return dbdma_setup(AU1550_DDMA_INT, au1550_dbdev_tab); case ALCHEMY_CPU_AU1200: return dbdma_setup(AU1200_DDMA_INT, au1200_dbdev_tab); + case ALCHEMY_CPU_AU1300: + return dbdma_setup(AU1300_DDMA_INT, au1300_dbdev_tab); } return 0; } diff --git a/arch/mips/alchemy/common/gpioint.c b/arch/mips/alchemy/common/gpioint.c new file mode 100644 index 000000000000..b8cd3364ff69 --- /dev/null +++ b/arch/mips/alchemy/common/gpioint.c @@ -0,0 +1,411 @@ +/* + * gpioint.c - Au1300 GPIO+Interrupt controller (I call it "GPIC") support. + * + * Copyright (c) 2009-2011 Manuel Lauss <manuel.lauss@googlemail.com> + * + * licensed under the GPLv2. + */ + +#include <linux/io.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/syscore_ops.h> +#include <linux/types.h> + +#include <asm/irq_cpu.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-au1x00/gpio-au1300.h> + +static int au1300_gpic_settype(struct irq_data *d, unsigned int type); + +/* setup for known onchip sources */ +struct gpic_devint_data { + int irq; /* linux IRQ number */ + int type; /* IRQ_TYPE_ */ + int prio; /* irq priority, 0 highest, 3 lowest */ + int internal; /* internal source (no ext. pin)? */ +}; + +static const struct gpic_devint_data au1300_devints[] __initdata = { + /* multifunction: gpio pin or device */ + { AU1300_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_SD1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_SD2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + { AU1300_NAND_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, }, + /* au1300 internal */ + { AU1300_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_MMU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_MPU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_GPU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_UDMA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_TOY_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_RTC_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0, 1, }, + { AU1300_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_SD0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_USB_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_BSA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_MPE_INT, IRQ_TYPE_EDGE_RISING, 1, 1, }, + { AU1300_ITE_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_AES_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { AU1300_CIM_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, }, + { -1, }, /* terminator */ +}; + + +/* + * au1300_gpic_chgcfg - change PIN configuration. + * @gpio: pin to change (0-based GPIO number from datasheet). + * @clr: clear all bits set in 'clr'. + * @set: set these bits. + * + * modifies a pins' configuration register, bits set in @clr will + * be cleared in the register, bits in @set will be set. + */ +static inline void au1300_gpic_chgcfg(unsigned int gpio, + unsigned long clr, + unsigned long set) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long l; + + r += gpio * 4; /* offset into pin config array */ + l = __raw_readl(r + AU1300_GPIC_PINCFG); + l &= ~clr; + l |= set; + __raw_writel(l, r + AU1300_GPIC_PINCFG); + wmb(); +} + +/* + * au1300_pinfunc_to_gpio - assign a pin as GPIO input (GPIO ctrl). + * @pin: pin (0-based GPIO number from datasheet). + * + * Assigns a GPIO pin to the GPIO controller, so its level can either + * be read or set through the generic GPIO functions. + * If you need a GPOUT, use au1300_gpio_set_value(pin, 0/1). + * REVISIT: is this function really necessary? + */ +void au1300_pinfunc_to_gpio(enum au1300_multifunc_pins gpio) +{ + au1300_gpio_direction_input(gpio + AU1300_GPIO_BASE); +} +EXPORT_SYMBOL_GPL(au1300_pinfunc_to_gpio); + +/* + * au1300_pinfunc_to_dev - assign a pin to the device function. + * @pin: pin (0-based GPIO number from datasheet). + * + * Assigns a GPIO pin to its associated device function; the pin will be + * driven by the device and not through GPIO functions. + */ +void au1300_pinfunc_to_dev(enum au1300_multifunc_pins gpio) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long bit; + + r += GPIC_GPIO_BANKOFF(gpio); + bit = GPIC_GPIO_TO_BIT(gpio); + __raw_writel(bit, r + AU1300_GPIC_DEVSEL); + wmb(); +} +EXPORT_SYMBOL_GPL(au1300_pinfunc_to_dev); + +/* + * au1300_set_irq_priority - set internal priority of IRQ. + * @irq: irq to set priority (linux irq number). + * @p: priority (0 = highest, 3 = lowest). + */ +void au1300_set_irq_priority(unsigned int irq, int p) +{ + irq -= ALCHEMY_GPIC_INT_BASE; + au1300_gpic_chgcfg(irq, GPIC_CFG_IL_MASK, GPIC_CFG_IL_SET(p)); +} +EXPORT_SYMBOL_GPL(au1300_set_irq_priority); + +/* + * au1300_set_dbdma_gpio - assign a gpio to one of the DBDMA triggers. + * @dchan: dbdma trigger select (0, 1). + * @gpio: pin to assign as trigger. + * + * DBDMA controller has 2 external trigger sources; this function + * assigns a GPIO to the selected trigger. + */ +void au1300_set_dbdma_gpio(int dchan, unsigned int gpio) +{ + unsigned long r; + + if ((dchan >= 0) && (dchan <= 1)) { + r = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL); + r &= ~(0xff << (8 * dchan)); + r |= (gpio & 0x7f) << (8 * dchan); + __raw_writel(r, AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL); + wmb(); + } +} + +/**********************************************************************/ + +static inline void gpic_pin_set_idlewake(unsigned int gpio, int allow) +{ + au1300_gpic_chgcfg(gpio, GPIC_CFG_IDLEWAKE, + allow ? GPIC_CFG_IDLEWAKE : 0); +} + +static void au1300_gpic_mask(struct irq_data *d) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long bit, irq = d->irq; + + irq -= ALCHEMY_GPIC_INT_BASE; + r += GPIC_GPIO_BANKOFF(irq); + bit = GPIC_GPIO_TO_BIT(irq); + __raw_writel(bit, r + AU1300_GPIC_IDIS); + wmb(); + + gpic_pin_set_idlewake(irq, 0); +} + +static void au1300_gpic_unmask(struct irq_data *d) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long bit, irq = d->irq; + + irq -= ALCHEMY_GPIC_INT_BASE; + + gpic_pin_set_idlewake(irq, 1); + + r += GPIC_GPIO_BANKOFF(irq); + bit = GPIC_GPIO_TO_BIT(irq); + __raw_writel(bit, r + AU1300_GPIC_IEN); + wmb(); +} + +static void au1300_gpic_maskack(struct irq_data *d) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long bit, irq = d->irq; + + irq -= ALCHEMY_GPIC_INT_BASE; + r += GPIC_GPIO_BANKOFF(irq); + bit = GPIC_GPIO_TO_BIT(irq); + __raw_writel(bit, r + AU1300_GPIC_IPEND); /* ack */ + __raw_writel(bit, r + AU1300_GPIC_IDIS); /* mask */ + wmb(); + + gpic_pin_set_idlewake(irq, 0); +} + +static void au1300_gpic_ack(struct irq_data *d) +{ + void __iomem *r = AU1300_GPIC_ADDR; + unsigned long bit, irq = d->irq; + + irq -= ALCHEMY_GPIC_INT_BASE; + r += GPIC_GPIO_BANKOFF(irq); + bit = GPIC_GPIO_TO_BIT(irq); + __raw_writel(bit, r + AU1300_GPIC_IPEND); /* ack */ + wmb(); +} + +static struct irq_chip au1300_gpic = { + .name = "GPIOINT", + .irq_ack = au1300_gpic_ack, + .irq_mask = au1300_gpic_mask, + .irq_mask_ack = au1300_gpic_maskack, + .irq_unmask = au1300_gpic_unmask, + .irq_set_type = au1300_gpic_settype, +}; + +static int au1300_gpic_settype(struct irq_data *d, unsigned int type) +{ + unsigned long s; + unsigned char *name = NULL; + irq_flow_handler_t hdl = NULL; + + switch (type) { + case IRQ_TYPE_LEVEL_HIGH: + s = GPIC_CFG_IC_LEVEL_HIGH; + name = "high"; + hdl = handle_level_irq; + break; + case IRQ_TYPE_LEVEL_LOW: + s = GPIC_CFG_IC_LEVEL_LOW; + name = "low"; + hdl = handle_level_irq; + break; + case IRQ_TYPE_EDGE_RISING: + s = GPIC_CFG_IC_EDGE_RISE; + name = "posedge"; + hdl = handle_edge_irq; + break; + case IRQ_TYPE_EDGE_FALLING: + s = GPIC_CFG_IC_EDGE_FALL; + name = "negedge"; + hdl = handle_edge_irq; + break; + case IRQ_TYPE_EDGE_BOTH: + s = GPIC_CFG_IC_EDGE_BOTH; + name = "bothedge"; + hdl = handle_edge_irq; + break; + case IRQ_TYPE_NONE: + s = GPIC_CFG_IC_OFF; + name = "disabled"; + hdl = handle_level_irq; + break; + default: + return -EINVAL; + } + + __irq_set_chip_handler_name_locked(d->irq, &au1300_gpic, hdl, name); + + au1300_gpic_chgcfg(d->irq - ALCHEMY_GPIC_INT_BASE, GPIC_CFG_IC_MASK, s); + + return 0; +} + +static void __init alchemy_gpic_init_irq(const struct gpic_devint_data *dints) +{ + int i; + void __iomem *bank_base; + + mips_cpu_irq_init(); + + /* disable & ack all possible interrupt sources */ + for (i = 0; i < 4; i++) { + bank_base = AU1300_GPIC_ADDR + (i * 4); + __raw_writel(~0UL, bank_base + AU1300_GPIC_IDIS); + wmb(); + __raw_writel(~0UL, bank_base + AU1300_GPIC_IPEND); + wmb(); + } + + /* register an irq_chip for them, with 2nd highest priority */ + for (i = ALCHEMY_GPIC_INT_BASE; i <= ALCHEMY_GPIC_INT_LAST; i++) { + au1300_set_irq_priority(i, 1); + au1300_gpic_settype(irq_get_irq_data(i), IRQ_TYPE_NONE); + } + + /* setup known on-chip sources */ + while ((i = dints->irq) != -1) { + au1300_gpic_settype(irq_get_irq_data(i), dints->type); + au1300_set_irq_priority(i, dints->prio); + + if (dints->internal) + au1300_pinfunc_to_dev(i - ALCHEMY_GPIC_INT_BASE); + + dints++; + } + + set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3); +} + +static unsigned long alchemy_gpic_pmdata[ALCHEMY_GPIC_INT_NUM + 6]; + +static int alchemy_gpic_suspend(void) +{ + void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR); + int i; + + /* save 4 interrupt mask status registers */ + alchemy_gpic_pmdata[0] = __raw_readl(base + AU1300_GPIC_IEN + 0x0); + alchemy_gpic_pmdata[1] = __raw_readl(base + AU1300_GPIC_IEN + 0x4); + alchemy_gpic_pmdata[2] = __raw_readl(base + AU1300_GPIC_IEN + 0x8); + alchemy_gpic_pmdata[3] = __raw_readl(base + AU1300_GPIC_IEN + 0xc); + + /* save misc register(s) */ + alchemy_gpic_pmdata[4] = __raw_readl(base + AU1300_GPIC_DMASEL); + + /* molto silenzioso */ + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc); + wmb(); + + /* save pin/int-type configuration */ + base += AU1300_GPIC_PINCFG; + for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++) + alchemy_gpic_pmdata[i + 5] = __raw_readl(base + (i << 2)); + + wmb(); + + return 0; +} + +static void alchemy_gpic_resume(void) +{ + void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR); + int i; + + /* disable all first */ + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8); + __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc); + wmb(); + + /* restore pin/int-type configurations */ + base += AU1300_GPIC_PINCFG; + for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++) + __raw_writel(alchemy_gpic_pmdata[i + 5], base + (i << 2)); + wmb(); + + /* restore misc register(s) */ + base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR); + __raw_writel(alchemy_gpic_pmdata[4], base + AU1300_GPIC_DMASEL); + wmb(); + + /* finally restore masks */ + __raw_writel(alchemy_gpic_pmdata[0], base + AU1300_GPIC_IEN + 0x0); + __raw_writel(alchemy_gpic_pmdata[1], base + AU1300_GPIC_IEN + 0x4); + __raw_writel(alchemy_gpic_pmdata[2], base + AU1300_GPIC_IEN + 0x8); + __raw_writel(alchemy_gpic_pmdata[3], base + AU1300_GPIC_IEN + 0xc); + wmb(); +} + +static struct syscore_ops alchemy_gpic_pmops = { + .suspend = alchemy_gpic_suspend, + .resume = alchemy_gpic_resume, +}; + +/**********************************************************************/ + +void __init arch_init_irq(void) +{ + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1300: + alchemy_gpic_init_irq(&au1300_devints[0]); + register_syscore_ops(&alchemy_gpic_pmops); + break; + } +} + +#define CAUSEF_GPIC (CAUSEF_IP2 | CAUSEF_IP3 | CAUSEF_IP4 | CAUSEF_IP5) + +void plat_irq_dispatch(void) +{ + unsigned long i, c = read_c0_cause() & read_c0_status(); + + if (c & CAUSEF_IP7) /* c0 timer */ + do_IRQ(MIPS_CPU_IRQ_BASE + 7); + else if (likely(c & CAUSEF_GPIC)) { + i = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_PRIENC); + do_IRQ(i + ALCHEMY_GPIC_INT_BASE); + } else + spurious_interrupt(); +} diff --git a/arch/mips/alchemy/common/gpiolib.c b/arch/mips/alchemy/common/gpiolib.c index 91fb4d9e30fd..f1b50f0c01db 100644 --- a/arch/mips/alchemy/common/gpiolib.c +++ b/arch/mips/alchemy/common/gpiolib.c @@ -27,6 +27,7 @@ * CONFIG_ALCHEMY_GPIO_INDIRECT=n, otherwise compilation will fail! * au1000 SoC have only one GPIO block : GPIO1 * Au1100, Au15x0, Au12x0 have a second one : GPIO2 + * Au1300 is totally different: 1 block with up to 128 GPIOs */ #include <linux/init.h> @@ -35,6 +36,7 @@ #include <linux/types.h> #include <linux/gpio.h> #include <asm/mach-au1x00/gpio-au1000.h> +#include <asm/mach-au1x00/gpio-au1300.h> static int gpio2_get(struct gpio_chip *chip, unsigned offset) { @@ -115,6 +117,43 @@ struct gpio_chip alchemy_gpio_chip[] = { }, }; +static int alchemy_gpic_get(struct gpio_chip *chip, unsigned int off) +{ + return au1300_gpio_get_value(off + AU1300_GPIO_BASE); +} + +static void alchemy_gpic_set(struct gpio_chip *chip, unsigned int off, int v) +{ + au1300_gpio_set_value(off + AU1300_GPIO_BASE, v); +} + +static int alchemy_gpic_dir_input(struct gpio_chip *chip, unsigned int off) +{ + return au1300_gpio_direction_input(off + AU1300_GPIO_BASE); +} + +static int alchemy_gpic_dir_output(struct gpio_chip *chip, unsigned int off, + int v) +{ + return au1300_gpio_direction_output(off + AU1300_GPIO_BASE, v); +} + +static int alchemy_gpic_gpio_to_irq(struct gpio_chip *chip, unsigned int off) +{ + return au1300_gpio_to_irq(off + AU1300_GPIO_BASE); +} + +static struct gpio_chip au1300_gpiochip = { + .label = "alchemy-gpic", + .direction_input = alchemy_gpic_dir_input, + .direction_output = alchemy_gpic_dir_output, + .get = alchemy_gpic_get, + .set = alchemy_gpic_set, + .to_irq = alchemy_gpic_gpio_to_irq, + .base = AU1300_GPIO_BASE, + .ngpio = AU1300_GPIO_NUM, +}; + static int __init alchemy_gpiochip_init(void) { int ret = 0; @@ -127,6 +166,9 @@ static int __init alchemy_gpiochip_init(void) ret = gpiochip_add(&alchemy_gpio_chip[0]); ret |= gpiochip_add(&alchemy_gpio_chip[1]); break; + case ALCHEMY_CPU_AU1300: + ret = gpiochip_add(&au1300_gpiochip); + break; } return ret; } diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c index c8e5d72a5826..95cb9113b12c 100644 --- a/arch/mips/alchemy/common/platform.c +++ b/arch/mips/alchemy/common/platform.c @@ -82,6 +82,12 @@ static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = { PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT), PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT), }, + [ALCHEMY_CPU_AU1300] = { + PORT(AU1300_UART0_PHYS_ADDR, AU1300_UART0_INT), + PORT(AU1300_UART1_PHYS_ADDR, AU1300_UART1_INT), + PORT(AU1300_UART2_PHYS_ADDR, AU1300_UART2_INT), + PORT(AU1300_UART3_PHYS_ADDR, AU1300_UART3_INT), + }, }; static struct platform_device au1xx0_uart_device = { @@ -122,10 +128,12 @@ static unsigned long alchemy_ohci_data[][2] __initdata = { [ALCHEMY_CPU_AU1100] = { AU1000_USB_OHCI_PHYS_ADDR, AU1100_USB_HOST_INT }, [ALCHEMY_CPU_AU1550] = { AU1550_USB_OHCI_PHYS_ADDR, AU1550_USB_HOST_INT }, [ALCHEMY_CPU_AU1200] = { AU1200_USB_OHCI_PHYS_ADDR, AU1200_USB_INT }, + [ALCHEMY_CPU_AU1300] = { AU1300_USB_OHCI0_PHYS_ADDR, AU1300_USB_INT }, }; static unsigned long alchemy_ehci_data[][2] __initdata = { [ALCHEMY_CPU_AU1200] = { AU1200_USB_EHCI_PHYS_ADDR, AU1200_USB_INT }, + [ALCHEMY_CPU_AU1300] = { AU1300_USB_EHCI_PHYS_ADDR, AU1300_USB_INT }, }; static int __init _new_usbres(struct resource **r, struct platform_device **d) @@ -169,8 +177,8 @@ static void __init alchemy_setup_usb(int ctype) printk(KERN_INFO "Alchemy USB: cannot add OHCI0\n"); - /* setup EHCI0: Au1200 */ - if (ctype == ALCHEMY_CPU_AU1200) { + /* setup EHCI0: Au1200/Au1300 */ + if ((ctype == ALCHEMY_CPU_AU1200) || (ctype == ALCHEMY_CPU_AU1300)) { if (_new_usbres(&res, &pdev)) return; @@ -187,6 +195,25 @@ static void __init alchemy_setup_usb(int ctype) if (platform_device_register(pdev)) printk(KERN_INFO "Alchemy USB: cannot add EHCI0\n"); } + + /* Au1300: OHCI1 */ + if (ctype == ALCHEMY_CPU_AU1300) { + if (_new_usbres(&res, &pdev)) + return; + + res[0].start = AU1300_USB_OHCI1_PHYS_ADDR; + res[0].end = res[0].start + 0x100 - 1; + res[0].flags = IORESOURCE_MEM; + res[1].start = AU1300_USB_INT; + res[1].end = res[1].start; + res[1].flags = IORESOURCE_IRQ; + pdev->name = "au1xxx-ohci"; + pdev->id = 1; + pdev->dev.dma_mask = &alchemy_ohci_dmamask; + + if (platform_device_register(pdev)) + printk(KERN_INFO "Alchemy USB: cannot add OHCI1\n"); + } } /* Macro to help defining the Ethernet MAC resources */ diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c index bdd6651e9a4f..0c7fce2a3c12 100644 --- a/arch/mips/alchemy/common/power.c +++ b/arch/mips/alchemy/common/power.c @@ -126,6 +126,9 @@ void au_sleep(void) case ALCHEMY_CPU_AU1200: alchemy_sleep_au1550(); break; + case ALCHEMY_CPU_AU1300: + alchemy_sleep_au1300(); + break; } restore_core_regs(); diff --git a/arch/mips/alchemy/common/sleeper.S b/arch/mips/alchemy/common/sleeper.S index 77f3c743b716..c7bcc7e5c822 100644 --- a/arch/mips/alchemy/common/sleeper.S +++ b/arch/mips/alchemy/common/sleeper.S @@ -153,6 +153,79 @@ LEAF(alchemy_sleep_au1550) END(alchemy_sleep_au1550) +/* sleepcode for Au1300 memory controller type */ +LEAF(alchemy_sleep_au1300) + + SETUP_SLEEP + + /* cache following instructions, as memory gets put to sleep */ + la t0, 2f + la t1, 4f + subu t2, t1, t0 + + .set mips3 + +1: cache 0x14, 0(t0) + subu t2, t2, 32 + bgez t2, 1b + addu t0, t0, 32 + + .set mips0 + +2: lui a0, 0xb400 /* mem_xxx */ + + /* disable all ports in mem_sdportcfga */ + sw zero, 0x868(a0) /* mem_sdportcfga */ + sync + + /* disable ODT */ + li t0, 0x03010000 + sw t0, 0x08d8(a0) /* mem_sdcmd0 */ + sw t0, 0x08dc(a0) /* mem_sdcmd1 */ + sync + + /* precharge */ + li t0, 0x23000400 + sw t0, 0x08dc(a0) /* mem_sdcmd1 */ + sw t0, 0x08d8(a0) /* mem_sdcmd0 */ + sync + + /* auto refresh */ + sw zero, 0x08c8(a0) /* mem_sdautoref */ + sync + + /* block access to the DDR */ + lw t0, 0x0848(a0) /* mem_sdconfigb */ + li t1, (1 << 7 | 0x3F) + or t0, t0, t1 + sw t0, 0x0848(a0) /* mem_sdconfigb */ + sync + + /* issue the Self Refresh command */ + li t0, 0x10000000 + sw t0, 0x08dc(a0) /* mem_sdcmd1 */ + sw t0, 0x08d8(a0) /* mem_sdcmd0 */ + sync + + /* wait for sdram to enter self-refresh mode */ + lui t0, 0x0300 +3: lw t1, 0x0850(a0) /* mem_sdstat */ + and t2, t1, t0 + bne t2, t0, 3b + nop + + /* disable SDRAM clocks */ + li t0, ~(3<<28) + lw t1, 0x0840(a0) /* mem_sdconfiga */ + and t1, t1, t0 /* clear CE[1:0] */ + sw t1, 0x0840(a0) /* mem_sdconfiga */ + sync + + DO_SLEEP +4: + +END(alchemy_sleep_au1300) + /* This is where we return upon wakeup. * Reload all of the registers and return. diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c index d5da6adbf634..a594a85337d6 100644 --- a/arch/mips/alchemy/common/time.c +++ b/arch/mips/alchemy/common/time.c @@ -178,6 +178,7 @@ static int alchemy_m2inttab[] __initdata = { AU1100_RTC_MATCH2_INT, AU1550_RTC_MATCH2_INT, AU1200_RTC_MATCH2_INT, + AU1300_RTC_MATCH2_INT, }; void __init plat_time_init(void) diff --git a/arch/mips/alchemy/common/vss.c b/arch/mips/alchemy/common/vss.c new file mode 100644 index 000000000000..d23b1444d365 --- /dev/null +++ b/arch/mips/alchemy/common/vss.c @@ -0,0 +1,84 @@ +/* + * Au1300 media block power gating (VSS) + * + * This is a stop-gap solution until I have the clock framework integration + * ready. This stuff here really must be handled transparently when clocks + * for various media blocks are enabled/disabled. + */ + +#include <linux/module.h> +#include <linux/spinlock.h> +#include <asm/mach-au1x00/au1000.h> + +#define VSS_GATE 0x00 /* gate wait timers */ +#define VSS_CLKRST 0x04 /* clock/block control */ +#define VSS_FTR 0x08 /* footers */ + +#define VSS_ADDR(blk) (KSEG1ADDR(AU1300_VSS_PHYS_ADDR) + (blk * 0x0c)) + +static DEFINE_SPINLOCK(au1300_vss_lock); + +/* enable a block as outlined in the databook */ +static inline void __enable_block(int block) +{ + void __iomem *base = (void __iomem *)VSS_ADDR(block); + + __raw_writel(3, base + VSS_CLKRST); /* enable clock, assert reset */ + wmb(); + + __raw_writel(0x01fffffe, base + VSS_GATE); /* maximum setup time */ + wmb(); + + /* enable footers in sequence */ + __raw_writel(0x01, base + VSS_FTR); + wmb(); + __raw_writel(0x03, base + VSS_FTR); + wmb(); + __raw_writel(0x07, base + VSS_FTR); + wmb(); + __raw_writel(0x0f, base + VSS_FTR); + wmb(); + + __raw_writel(0x01ffffff, base + VSS_GATE); /* start FSM too */ + wmb(); + + __raw_writel(2, base + VSS_CLKRST); /* deassert reset */ + wmb(); + + __raw_writel(0x1f, base + VSS_FTR); /* enable isolation cells */ + wmb(); +} + +/* disable a block as outlined in the databook */ +static inline void __disable_block(int block) +{ + void __iomem *base = (void __iomem *)VSS_ADDR(block); + + __raw_writel(0x0f, base + VSS_FTR); /* disable isolation cells */ + wmb(); + __raw_writel(0, base + VSS_GATE); /* disable FSM */ + wmb(); + __raw_writel(3, base + VSS_CLKRST); /* assert reset */ + wmb(); + __raw_writel(1, base + VSS_CLKRST); /* disable clock */ + wmb(); + __raw_writel(0, base + VSS_FTR); /* disable all footers */ + wmb(); +} + +void au1300_vss_block_control(int block, int enable) +{ + unsigned long flags; + + if (alchemy_get_cputype() != ALCHEMY_CPU_AU1300) + return; + + /* only one block at a time */ + spin_lock_irqsave(&au1300_vss_lock, flags); + if (enable) + __enable_block(block); + else + __disable_block(block); + spin_unlock_irqrestore(&au1300_vss_lock, flags); +} +EXPORT_SYMBOL_GPL(au1300_vss_block_control); |