diff options
Diffstat (limited to 'arch/powerpc/boot/dts')
23 files changed, 1525 insertions, 252 deletions
diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts index 27bd267d631c..a7511f2d844d 100644 --- a/arch/powerpc/boot/dts/digsy_mtc.dts +++ b/arch/powerpc/boot/dts/digsy_mtc.dts @@ -23,19 +23,26 @@ soc5200@f0000000 { timer@600 { // General Purpose Timer + #gpio-cells = <2>; fsl,has-wdt; + gpio-controller; }; - rtc@800 { - status = "disabled"; + timer@610 { + #gpio-cells = <2>; + gpio-controller; }; - can@900 { + rtc@800 { status = "disabled"; }; - can@980 { - status = "disabled"; + spi@f00 { + msp430@0 { + compatible = "spidev"; + spi-max-frequency = <32000>; + reg = <0>; + }; }; psc@2000 { // PSC1 @@ -73,11 +80,16 @@ }; i2c@3d00 { - rtc@50 { + eeprom@50 { compatible = "at,24c08"; reg = <0x50>; }; + rtc@56 { + compatible = "mc,rv3029c2"; + reg = <0x56>; + }; + rtc@68 { compatible = "dallas,ds1339"; reg = <0x68>; @@ -90,11 +102,22 @@ }; pci@f0000d00 { - status = "disabled"; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 + 0xc000 0 0 2 &mpc5200_pic 0 0 3 + 0xc000 0 0 3 &mpc5200_pic 0 0 3 + 0xc000 0 0 4 &mpc5200_pic 0 0 3>; + clock-frequency = <0>; // From boot loader + interrupts = <2 8 0 2 9 0 2 10 0>; + bus-range = <0 0>; + ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000 + 0x02000000 0 0x90000000 0x90000000 0 0x10000000 + 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>; }; localbus { - ranges = <0 0 0xff000000 0x1000000>; + ranges = <0 0 0xff000000 0x1000000 + 4 0 0x60000000 0x0001000>; // 16-bit flash device at LocalPlus Bus CS0 flash@0,0 { @@ -122,5 +145,25 @@ reg = <0x00f00000 0x100000>; }; }; + + can@4,0 { + compatible = "nxp,sja1000"; + reg = <4 0x000 0x80>; + nxp,external-clock-frequency = <24000000>; + interrupts = <1 2 3>; // Level-low + }; + + can@4,100 { + compatible = "nxp,sja1000"; + reg = <4 0x100 0x80>; + nxp,external-clock-frequency = <24000000>; + interrupts = <1 2 3>; // Level-low + }; + + serial@4,200 { + compatible = "nxp,sc28l92"; + reg = <4 0x200 0x10>; + interrupts = <1 3 3>; + }; }; }; diff --git a/arch/powerpc/boot/dts/gef_ppc9a.dts b/arch/powerpc/boot/dts/gef_ppc9a.dts index 83f4b79dff85..2266bbb303d0 100644 --- a/arch/powerpc/boot/dts/gef_ppc9a.dts +++ b/arch/powerpc/boot/dts/gef_ppc9a.dts @@ -269,14 +269,16 @@ enet0: ethernet@24000 { #address-cells = <1>; #size-cells = <1>; + cell-index = <0>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x24000 0x1000>; ranges = <0x0 0x24000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>; + interrupts = <29 2 30 2 34 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi0>; phy-handle = <&phy0>; phy-connection-type = "gmii"; @@ -290,25 +292,48 @@ interrupt-parent = <&gef_pic>; interrupts = <0x9 0x4>; reg = <1>; + device_type = "ethernet-phy"; }; phy2: ethernet-phy@2 { interrupt-parent = <&gef_pic>; interrupts = <0x8 0x4>; reg = <3>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; }; }; }; enet1: ethernet@26000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <2>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x26000 0x1000>; + ranges = <0x0 0x26000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1f 0x2 0x20 0x2 0x21 0x2>; + interrupts = <31 2 32 2 33 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi2>; phy-handle = <&phy2>; phy-connection-type = "gmii"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi2: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; }; serial0: serial@4500 { diff --git a/arch/powerpc/boot/dts/gef_sbc310.dts b/arch/powerpc/boot/dts/gef_sbc310.dts index fc3a331dd392..429e87d9acef 100644 --- a/arch/powerpc/boot/dts/gef_sbc310.dts +++ b/arch/powerpc/boot/dts/gef_sbc310.dts @@ -267,14 +267,16 @@ enet0: ethernet@24000 { #address-cells = <1>; #size-cells = <1>; + cell-index = <0>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x24000 0x1000>; ranges = <0x0 0x24000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>; + interrupts = <29 2 30 2 34 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi0>; phy-handle = <&phy0>; phy-connection-type = "gmii"; @@ -288,25 +290,48 @@ interrupt-parent = <&gef_pic>; interrupts = <0x9 0x4>; reg = <1>; + device_type = "ethernet-phy"; }; phy2: ethernet-phy@2 { interrupt-parent = <&gef_pic>; interrupts = <0x8 0x4>; reg = <3>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; }; }; }; enet1: ethernet@26000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <2>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x26000 0x1000>; + ranges = <0x0 0x26000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1f 0x2 0x20 0x2 0x21 0x2>; + interrupts = <31 2 32 2 33 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi2>; phy-handle = <&phy2>; phy-connection-type = "gmii"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi2: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; }; serial0: serial@4500 { diff --git a/arch/powerpc/boot/dts/gef_sbc610.dts b/arch/powerpc/boot/dts/gef_sbc610.dts index c0671cc98125..d81201ac2cad 100644 --- a/arch/powerpc/boot/dts/gef_sbc610.dts +++ b/arch/powerpc/boot/dts/gef_sbc610.dts @@ -267,14 +267,16 @@ enet0: ethernet@24000 { #address-cells = <1>; #size-cells = <1>; + cell-index = <0>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x24000 0x1000>; ranges = <0x0 0x24000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>; + interrupts = <29 2 30 2 34 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi0>; phy-handle = <&phy0>; phy-connection-type = "gmii"; @@ -288,25 +290,48 @@ interrupt-parent = <&gef_pic>; interrupts = <0x9 0x4>; reg = <1>; + device_type = "ethernet-phy"; }; phy2: ethernet-phy@2 { interrupt-parent = <&gef_pic>; interrupts = <0x8 0x4>; reg = <3>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; }; }; }; enet1: ethernet@26000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <2>; device_type = "network"; - model = "eTSEC"; + model = "TSEC"; compatible = "gianfar"; reg = <0x26000 0x1000>; + ranges = <0x0 0x26000 0x1000>; local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <0x1f 0x2 0x20 0x2 0x21 0x2>; + interrupts = <31 2 32 2 33 2>; interrupt-parent = <&mpic>; + tbi-handle = <&tbi2>; phy-handle = <&phy2>; phy-connection-type = "gmii"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi2: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; }; serial0: serial@4500 { diff --git a/arch/powerpc/boot/dts/hcu4.dts b/arch/powerpc/boot/dts/hcu4.dts deleted file mode 100644 index 7988598da4c9..000000000000 --- a/arch/powerpc/boot/dts/hcu4.dts +++ /dev/null @@ -1,168 +0,0 @@ -/* -* Device Tree Source for Netstal Maschinen HCU4 -* based on the IBM Walnut -* -* Copyright 2008 -* Niklaus Giger <niklaus.giger@member.fsf.org> -* -* Copyright 2007 IBM Corp. -* Josh Boyer <jwboyer@linux.vnet.ibm.com> -* -* This file is licensed under the terms of the GNU General Public -* License version 2. This program is licensed "as is" without -* any warranty of any kind, whether express or implied. -*/ - -/dts-v1/; - -/ { - #address-cells = <0x1>; - #size-cells = <0x1>; - model = "netstal,hcu4"; - compatible = "netstal,hcu4"; - dcr-parent = <0x1>; - - aliases { - ethernet0 = "/plb/opb/ethernet@ef600800"; - serial0 = "/plb/opb/serial@ef600300"; - }; - - cpus { - #address-cells = <0x1>; - #size-cells = <0x0>; - - cpu@0 { - device_type = "cpu"; - model = "PowerPC,405GPr"; - reg = <0x0>; - clock-frequency = <0>; /* Filled in by U-Boot */ - timebase-frequency = <0x0>; /* Filled in by U-Boot */ - i-cache-line-size = <0x20>; - d-cache-line-size = <0x20>; - i-cache-size = <0x4000>; - d-cache-size = <0x4000>; - dcr-controller; - dcr-access-method = "native"; - linux,phandle = <0x1>; - }; - }; - - memory { - device_type = "memory"; - reg = <0x0 0x0>; /* Filled in by U-Boot */ - }; - - UIC0: interrupt-controller { - compatible = "ibm,uic"; - interrupt-controller; - cell-index = <0x0>; - dcr-reg = <0xc0 0x9>; - #address-cells = <0x0>; - #size-cells = <0x0>; - #interrupt-cells = <0x2>; - linux,phandle = <0x2>; - }; - - plb { - compatible = "ibm,plb3"; - #address-cells = <0x1>; - #size-cells = <0x1>; - ranges; - clock-frequency = <0x0>; /* Filled in by U-Boot */ - - SDRAM0: memory-controller { - compatible = "ibm,sdram-405gp"; - dcr-reg = <0x10 0x2>; - }; - - MAL: mcmal { - compatible = "ibm,mcmal-405gp", "ibm,mcmal"; - dcr-reg = <0x180 0x62>; - num-tx-chans = <0x1>; - num-rx-chans = <0x1>; - interrupt-parent = <0x2>; - interrupts = <0xb 0x4 0xc 0x4 0xa 0x4 0xd 0x4 0xe 0x4>; - linux,phandle = <0x3>; - }; - - POB0: opb { - compatible = "ibm,opb-405gp", "ibm,opb"; - #address-cells = <0x1>; - #size-cells = <0x1>; - ranges = <0xef600000 0xef600000 0xa00000>; - dcr-reg = <0xa0 0x5>; - clock-frequency = <0x0>; /* Filled in by U-Boot */ - - UART0: serial@ef600300 { - device_type = "serial"; - compatible = "ns16550"; - reg = <0xef600300 0x8>; - virtual-reg = <0xef600300>; - clock-frequency = <0x0>;/* Filled in by U-Boot */ - current-speed = <0>; /* Filled in by U-Boot */ - interrupt-parent = <0x2>; - interrupts = <0x0 0x4>; - }; - - IIC: i2c@ef600500 { - compatible = "ibm,iic-405gp", "ibm,iic"; - reg = <0xef600500 0x11>; - interrupt-parent = <0x2>; - interrupts = <0x2 0x4>; - }; - - GPIO: gpio@ef600700 { - compatible = "ibm,gpio-405gp"; - reg = <0xef600700 0x20>; - }; - - EMAC: ethernet@ef600800 { - device_type = "network"; - compatible = "ibm,emac-405gp", "ibm,emac"; - interrupt-parent = <0x2>; - interrupts = <0xf 0x4 0x9 0x4>; - local-mac-address = [00 00 00 00 00 00]; - reg = <0xef600800 0x70>; - mal-device = <0x3>; - mal-tx-channel = <0x0>; - mal-rx-channel = <0x0>; - cell-index = <0x0>; - max-frame-size = <0x5dc>; - rx-fifo-size = <0x1000>; - tx-fifo-size = <0x800>; - phy-mode = "rmii"; - phy-map = <0x1>; - }; - }; - - EBC0: ebc { - compatible = "ibm,ebc-405gp", "ibm,ebc"; - dcr-reg = <0x12 0x2>; - #address-cells = <0x2>; - #size-cells = <0x1>; - clock-frequency = <0x0>; /* Filled in by U-Boot */ - - sram@0,0 { - reg = <0x0 0x0 0x80000>; - }; - - flash@0,80000 { - compatible = "jedec-flash"; - bank-width = <0x1>; - reg = <0x0 0x80000 0x80000>; - #address-cells = <0x1>; - #size-cells = <0x1>; - - partition@0 { - label = "OpenBIOS"; - reg = <0x0 0x80000>; - read-only; - }; - }; - }; - }; - - chosen { - linux,stdout-path = "/plb/opb/serial@ef600300"; - }; -}; diff --git a/arch/powerpc/boot/dts/ksi8560.dts b/arch/powerpc/boot/dts/ksi8560.dts index bdb7fc0fa332..296c572ea605 100644 --- a/arch/powerpc/boot/dts/ksi8560.dts +++ b/arch/powerpc/boot/dts/ksi8560.dts @@ -306,7 +306,7 @@ localbus@fdf05000 { #address-cells = <2>; #size-cells = <1>; - compatible = "fsl,mpc8560-localbus"; + compatible = "fsl,mpc8560-localbus", "simple-bus"; reg = <0xfdf05000 0x68>; ranges = <0x0 0x0 0xe0000000 0x00800000 diff --git a/arch/powerpc/boot/dts/mgcoge.dts b/arch/powerpc/boot/dts/mgcoge.dts index 1360d2f69024..ededaf5ac015 100644 --- a/arch/powerpc/boot/dts/mgcoge.dts +++ b/arch/powerpc/boot/dts/mgcoge.dts @@ -213,6 +213,15 @@ linux,network-index = <2>; fsl,cpm-command = <0x16200300>; }; + + usb@11b60 { + compatible = "fsl,mpc8272-cpm-usb"; + mode = "peripheral"; + reg = <0x11b60 0x40 0x8b00 0x100>; + interrupts = <11 8>; + interrupt-parent = <&PIC>; + usb-clock = <5>; + }; }; cpm2_pio_c: gpio-controller@10d40 { diff --git a/arch/powerpc/boot/dts/mpc5200b.dtsi b/arch/powerpc/boot/dts/mpc5200b.dtsi index bc27548e895d..7ab286ab5300 100644 --- a/arch/powerpc/boot/dts/mpc5200b.dtsi +++ b/arch/powerpc/boot/dts/mpc5200b.dtsi @@ -147,6 +147,8 @@ }; spi@f00 { + #address-cells = <1>; + #size-cells = <0>; compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; reg = <0xf00 0x20>; interrupts = <2 13 0 2 14 0>; diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts index b53d1df11e2d..505dc842d808 100644 --- a/arch/powerpc/boot/dts/mpc8349emitx.dts +++ b/arch/powerpc/boot/dts/mpc8349emitx.dts @@ -390,7 +390,8 @@ #address-cells = <2>; #size-cells = <1>; compatible = "fsl,mpc8349e-localbus", - "fsl,pq2pro-localbus"; + "fsl,pq2pro-localbus", + "simple-bus"; reg = <0xe0005000 0xd8>; ranges = <0x0 0x0 0xfe000000 0x1000000 /* flash */ 0x1 0x0 0xf8000000 0x20000 /* VSC 7385 */ diff --git a/arch/powerpc/boot/dts/p1022ds.dts b/arch/powerpc/boot/dts/p1022ds.dts index 1be9743ab5e0..b9b8719a6204 100644 --- a/arch/powerpc/boot/dts/p1022ds.dts +++ b/arch/powerpc/boot/dts/p1022ds.dts @@ -150,7 +150,7 @@ }; board-control@3,0 { - compatible = "fsl,p1022ds-pixis"; + compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis"; reg = <3 0 0x30>; interrupt-parent = <&mpic>; /* diff --git a/arch/powerpc/boot/dts/p2020ds.dts b/arch/powerpc/boot/dts/p2020ds.dts index dae403100f2f..66f03d6477b2 100644 --- a/arch/powerpc/boot/dts/p2020ds.dts +++ b/arch/powerpc/boot/dts/p2020ds.dts @@ -118,6 +118,11 @@ }; }; + board-control@3,0 { + compatible = "fsl,p2020ds-fpga", "fsl,fpga-ngpixis"; + reg = <0x3 0x0 0x30>; + }; + nand@4,0 { compatible = "fsl,elbc-fcm-nand"; reg = <0x4 0x0 0x40000>; diff --git a/arch/powerpc/boot/dts/p2040rdb.dts b/arch/powerpc/boot/dts/p2041rdb.dts index 7d84e391c632..79b6895027c0 100644 --- a/arch/powerpc/boot/dts/p2040rdb.dts +++ b/arch/powerpc/boot/dts/p2041rdb.dts @@ -1,5 +1,5 @@ /* - * P2040RDB Device Tree Source + * P2041RDB Device Tree Source * * Copyright 2011 Freescale Semiconductor Inc. * @@ -32,11 +32,11 @@ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ -/include/ "p2040si.dtsi" +/include/ "p2041si.dtsi" / { - model = "fsl,P2040RDB"; - compatible = "fsl,P2040RDB"; + model = "fsl,P2041RDB"; + compatible = "fsl,P2041RDB"; #address-cells = <2>; #size-cells = <2>; interrupt-parent = <&mpic>; @@ -45,6 +45,10 @@ device_type = "memory"; }; + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + soc: soc@ffe000000 { spi@110000 { flash@0 { @@ -97,13 +101,8 @@ }; }; - usb0: usb@210000 { - phy_type = "utmi"; - }; - usb1: usb@211000 { dr_mode = "host"; - phy_type = "utmi"; }; }; diff --git a/arch/powerpc/boot/dts/p2040si.dtsi b/arch/powerpc/boot/dts/p2041si.dtsi index 5fdbb24c0763..f7492edd0dfd 100644 --- a/arch/powerpc/boot/dts/p2040si.dtsi +++ b/arch/powerpc/boot/dts/p2041si.dtsi @@ -1,5 +1,5 @@ /* - * P2040 Silicon Device Tree Source + * P2041 Silicon Device Tree Source * * Copyright 2011 Freescale Semiconductor Inc. * @@ -35,13 +35,14 @@ /dts-v1/; / { - compatible = "fsl,P2040"; + compatible = "fsl,P2041"; #address-cells = <2>; #size-cells = <2>; interrupt-parent = <&mpic>; aliases { ccsr = &soc; + dcsr = &dcsr; serial0 = &serial0; serial1 = &serial1; @@ -109,6 +110,74 @@ }; }; + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p2041-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p2041-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr>; + reg = <0x12000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p2041-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p2041-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + dcsr-cpu-sb-proxy@42000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu2>; + reg = <0x42000 0x1000>; + }; + dcsr-cpu-sb-proxy@43000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu3>; + reg = <0x43000 0x1000>; + }; + }; + soc: soc@ffe000000 { #address-cells = <1>; #size-cells = <1>; @@ -128,14 +197,14 @@ fsl,num-laws = <32>; }; - memory-controller@8000 { + ddr: memory-controller@8000 { compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller"; reg = <0x8000 0x1000>; interrupts = <16 2 1 23>; }; cpc: l3-cache-controller@10000 { - compatible = "fsl,p2040-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache"; + compatible = "fsl,p2041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache"; reg = <0x10000 0x1000>; interrupts = <16 2 1 27>; }; @@ -226,7 +295,7 @@ }; clockgen: global-utilities@e1000 { - compatible = "fsl,p2040-clockgen", "fsl,qoriq-clockgen-1.0"; + compatible = "fsl,p2041-clockgen", "fsl,qoriq-clockgen-1.0"; reg = <0xe1000 0x1000>; clock-frequency = <0>; }; @@ -238,45 +307,45 @@ }; sfp: sfp@e8000 { - compatible = "fsl,p2040-sfp", "fsl,qoriq-sfp-1.0"; + compatible = "fsl,p2041-sfp", "fsl,qoriq-sfp-1.0"; reg = <0xe8000 0x1000>; }; serdes: serdes@ea000 { - compatible = "fsl,p2040-serdes"; + compatible = "fsl,p2041-serdes"; reg = <0xea000 0x1000>; }; dma0: dma@100300 { #address-cells = <1>; #size-cells = <1>; - compatible = "fsl,p2040-dma", "fsl,eloplus-dma"; + compatible = "fsl,p2041-dma", "fsl,eloplus-dma"; reg = <0x100300 0x4>; ranges = <0x0 0x100100 0x200>; cell-index = <0>; dma-channel@0 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x0 0x80>; cell-index = <0>; interrupts = <28 2 0 0>; }; dma-channel@80 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x80 0x80>; cell-index = <1>; interrupts = <29 2 0 0>; }; dma-channel@100 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x100 0x80>; cell-index = <2>; interrupts = <30 2 0 0>; }; dma-channel@180 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x180 0x80>; cell-index = <3>; @@ -287,33 +356,33 @@ dma1: dma@101300 { #address-cells = <1>; #size-cells = <1>; - compatible = "fsl,p2040-dma", "fsl,eloplus-dma"; + compatible = "fsl,p2041-dma", "fsl,eloplus-dma"; reg = <0x101300 0x4>; ranges = <0x0 0x101100 0x200>; cell-index = <1>; dma-channel@0 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x0 0x80>; cell-index = <0>; interrupts = <32 2 0 0>; }; dma-channel@80 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x80 0x80>; cell-index = <1>; interrupts = <33 2 0 0>; }; dma-channel@100 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x100 0x80>; cell-index = <2>; interrupts = <34 2 0 0>; }; dma-channel@180 { - compatible = "fsl,p2040-dma-channel", + compatible = "fsl,p2041-dma-channel", "fsl,eloplus-dma-channel"; reg = <0x180 0x80>; cell-index = <3>; @@ -324,22 +393,20 @@ spi@110000 { #address-cells = <1>; #size-cells = <0>; - compatible = "fsl,p2040-espi", "fsl,mpc8536-espi"; + compatible = "fsl,p2041-espi", "fsl,mpc8536-espi"; reg = <0x110000 0x1000>; interrupts = <53 0x2 0 0>; fsl,espi-num-chipselects = <4>; - }; sdhc: sdhc@114000 { - compatible = "fsl,p2040-esdhc", "fsl,esdhc"; + compatible = "fsl,p2041-esdhc", "fsl,esdhc"; reg = <0x114000 0x1000>; interrupts = <48 2 0 0>; sdhci,auto-cmd12; clock-frequency = <0>; }; - i2c@118000 { #address-cells = <1>; #size-cells = <0>; @@ -417,7 +484,7 @@ }; gpio0: gpio@130000 { - compatible = "fsl,p2040-gpio", "fsl,qoriq-gpio"; + compatible = "fsl,p2041-gpio", "fsl,qoriq-gpio"; reg = <0x130000 0x1000>; interrupts = <55 2 0 0>; #gpio-cells = <2>; @@ -425,32 +492,34 @@ }; usb0: usb@210000 { - compatible = "fsl,p2040-usb2-mph", + compatible = "fsl,p2041-usb2-mph", "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph"; reg = <0x210000 0x1000>; #address-cells = <1>; #size-cells = <0>; interrupts = <44 0x2 0 0>; + phy_type = "utmi"; port0; }; usb1: usb@211000 { - compatible = "fsl,p2040-usb2-dr", + compatible = "fsl,p2041-usb2-dr", "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr"; reg = <0x211000 0x1000>; #address-cells = <1>; #size-cells = <0>; interrupts = <45 0x2 0 0>; + phy_type = "utmi"; }; sata@220000 { - compatible = "fsl,p2040-sata", "fsl,pq-sata-v2"; + compatible = "fsl,p2041-sata", "fsl,pq-sata-v2"; reg = <0x220000 0x1000>; interrupts = <68 0x2 0 0>; }; sata@221000 { - compatible = "fsl,p2040-sata", "fsl,pq-sata-v2"; + compatible = "fsl,p2041-sata", "fsl,pq-sata-v2"; reg = <0x221000 0x1000>; interrupts = <69 0x2 0 0>; }; @@ -534,19 +603,19 @@ }; localbus@ffe124000 { - compatible = "fsl,p2040-elbc", "fsl,elbc", "simple-bus"; + compatible = "fsl,p2041-elbc", "fsl,elbc", "simple-bus"; interrupts = <25 2 0 0>; #address-cells = <2>; #size-cells = <1>; }; pci0: pcie@ffe200000 { - compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2"; + compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2"; device_type = "pci"; #size-cells = <2>; #address-cells = <3>; bus-range = <0x0 0xff>; - clock-frequency = <0x1fca055>; + clock-frequency = <33333333>; fsl,msi = <&msi0>; interrupts = <16 2 1 15>; pcie@0 { @@ -568,12 +637,12 @@ }; pci1: pcie@ffe201000 { - compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2"; + compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2"; device_type = "pci"; #size-cells = <2>; #address-cells = <3>; bus-range = <0 0xff>; - clock-frequency = <0x1fca055>; + clock-frequency = <33333333>; fsl,msi = <&msi1>; interrupts = <16 2 1 14>; pcie@0 { @@ -595,12 +664,12 @@ }; pci2: pcie@ffe202000 { - compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2"; + compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2"; device_type = "pci"; #size-cells = <2>; #address-cells = <3>; bus-range = <0x0 0xff>; - clock-frequency = <0x1fca055>; + clock-frequency = <33333333>; fsl,msi = <&msi2>; interrupts = <16 2 1 13>; pcie@0 { diff --git a/arch/powerpc/boot/dts/p3041ds.dts b/arch/powerpc/boot/dts/p3041ds.dts index 69cae674f396..bbd113b49a8f 100644 --- a/arch/powerpc/boot/dts/p3041ds.dts +++ b/arch/powerpc/boot/dts/p3041ds.dts @@ -45,6 +45,10 @@ device_type = "memory"; }; + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + soc: soc@ffe000000 { spi@110000 { flash@0 { @@ -147,8 +151,8 @@ }; board-control@3,0 { - compatible = "fsl,p3041ds-pixis"; - reg = <3 0 0x20>; + compatible = "fsl,p3041ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; }; }; diff --git a/arch/powerpc/boot/dts/p3041si.dtsi b/arch/powerpc/boot/dts/p3041si.dtsi index 8b695801f505..87130b732bc7 100644 --- a/arch/powerpc/boot/dts/p3041si.dtsi +++ b/arch/powerpc/boot/dts/p3041si.dtsi @@ -42,6 +42,7 @@ aliases { ccsr = &soc; + dcsr = &dcsr; serial0 = &serial0; serial1 = &serial1; @@ -114,6 +115,74 @@ }; }; + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p43041-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p43041-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr>; + reg = <0x12000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p43041-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p43041-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + dcsr-cpu-sb-proxy@42000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu2>; + reg = <0x42000 0x1000>; + }; + dcsr-cpu-sb-proxy@43000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu3>; + reg = <0x43000 0x1000>; + }; + }; + soc: soc@ffe000000 { #address-cells = <1>; #size-cells = <1>; @@ -133,7 +202,7 @@ fsl,num-laws = <32>; }; - memory-controller@8000 { + ddr: memory-controller@8000 { compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller"; reg = <0x8000 0x1000>; interrupts = <16 2 1 23>; diff --git a/arch/powerpc/boot/dts/p3060qds.dts b/arch/powerpc/boot/dts/p3060qds.dts new file mode 100644 index 000000000000..08b9193213e7 --- /dev/null +++ b/arch/powerpc/boot/dts/p3060qds.dts @@ -0,0 +1,238 @@ +/* + * P3060QDS Device Tree Source + * + * Copyright 2011 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/include/ "p3060si.dtsi" + +/ { + model = "fsl,P3060QDS"; + compatible = "fsl,P3060QDS"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mpic>; + + memory { + device_type = "memory"; + }; + + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + + soc: soc@ffe000000 { + spi@110000 { + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25sl12801"; + reg = <0>; + spi-max-frequency = <40000000>; /* input clock */ + partition@u-boot { + label = "u-boot"; + reg = <0x00000000 0x00100000>; + read-only; + }; + partition@kernel { + label = "kernel"; + reg = <0x00100000 0x00500000>; + read-only; + }; + partition@dtb { + label = "dtb"; + reg = <0x00600000 0x00100000>; + read-only; + }; + partition@fs { + label = "file system"; + reg = <0x00700000 0x00900000>; + }; + }; + flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,en25q32b"; + reg = <1>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi1 { + label = "spi1"; + reg = <0x00000000 0x00400000>; + }; + }; + flash@2 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db081d"; + reg = <2>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi1 { + label = "spi2"; + reg = <0x00000000 0x00100000>; + }; + }; + flash@3 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,sst25wf040"; + reg = <3>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi3 { + label = "spi3"; + reg = <0x00000000 0x00080000>; + }; + }; + }; + + i2c@118000 { + eeprom@51 { + compatible = "at24,24c256"; + reg = <0x51>; + }; + eeprom@53 { + compatible = "at24,24c256"; + reg = <0x53>; + }; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + interrupts = <0x1 0x1 0 0>; + }; + }; + + usb0: usb@210000 { + phy_type = "ulpi"; + }; + + usb1: usb@211000 { + dr_mode = "host"; + phy_type = "ulpi"; + }; + }; + + rapidio@ffe0c0000 { + reg = <0xf 0xfe0c0000 0 0x11000>; + + port1 { + ranges = <0 0 0xc 0x20000000 0 0x10000000>; + }; + port2 { + ranges = <0 0 0xc 0x30000000 0 0x10000000>; + }; + }; + + localbus@ffe124000 { + reg = <0xf 0xfe124000 0 0x1000>; + ranges = <0 0 0xf 0xe8000000 0x08000000 + 2 0 0xf 0xffa00000 0x00040000 + 3 0 0xf 0xffdf0000 0x00008000>; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x08000000>; + bank-width = <2>; + device-width = <2>; + }; + + nand@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elbc-fcm-nand"; + reg = <0x2 0x0 0x40000>; + + partition@0 { + label = "NAND U-Boot Image"; + reg = <0x0 0x02000000>; + read-only; + }; + + partition@2000000 { + label = "NAND Root File System"; + reg = <0x02000000 0x10000000>; + }; + + partition@12000000 { + label = "NAND Compressed RFS Image"; + reg = <0x12000000 0x08000000>; + }; + + partition@1a000000 { + label = "NAND Linux Kernel Image"; + reg = <0x1a000000 0x04000000>; + }; + + partition@1e000000 { + label = "NAND DTB Image"; + reg = <0x1e000000 0x01000000>; + }; + + partition@1f000000 { + label = "NAND Writable User area"; + reg = <0x1f000000 0x21000000>; + }; + }; + + board-control@3,0 { + compatible = "fsl,p3060qds-fpga", "fsl,fpga-qixis"; + reg = <3 0 0x100>; + }; + }; + + pci0: pcie@ffe200000 { + reg = <0xf 0xfe200000 0 0x1000>; + ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000 + 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>; + pcie@0 { + ranges = <0x02000000 0 0xe0000000 + 0x02000000 0 0xe0000000 + 0 0x20000000 + + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00010000>; + }; + }; + + pci1: pcie@ffe201000 { + reg = <0xf 0xfe201000 0 0x1000>; + ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000 + 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>; + pcie@0 { + ranges = <0x02000000 0 0xe0000000 + 0x02000000 0 0xe0000000 + 0 0x20000000 + + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00010000>; + }; + }; +}; diff --git a/arch/powerpc/boot/dts/p3060si.dtsi b/arch/powerpc/boot/dts/p3060si.dtsi new file mode 100644 index 000000000000..68947e157bbc --- /dev/null +++ b/arch/powerpc/boot/dts/p3060si.dtsi @@ -0,0 +1,719 @@ +/* + * P3060 Silicon Device Tree Source + * + * Copyright 2011 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +/ { + compatible = "fsl,P3060"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mpic>; + + aliases { + ccsr = &soc; + dcsr = &dcsr; + + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + pci0 = &pci0; + pci1 = &pci1; + usb0 = &usb0; + usb1 = &usb1; + dma0 = &dma0; + dma1 = &dma1; + msi0 = &msi0; + msi1 = &msi1; + msi2 = &msi2; + + crypto = &crypto; + sec_jr0 = &sec_jr0; + sec_jr1 = &sec_jr1; + sec_jr2 = &sec_jr2; + sec_jr3 = &sec_jr3; + rtic_a = &rtic_a; + rtic_b = &rtic_b; + rtic_c = &rtic_c; + rtic_d = &rtic_d; + sec_mon = &sec_mon; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: PowerPC,e500mc@0 { + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu1: PowerPC,e500mc@1 { + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu4: PowerPC,e500mc@4 { + device_type = "cpu"; + reg = <4>; + next-level-cache = <&L2_4>; + L2_4: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu5: PowerPC,e500mc@5 { + device_type = "cpu"; + reg = <5>; + next-level-cache = <&L2_5>; + L2_5: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu6: PowerPC,e500mc@6 { + device_type = "cpu"; + reg = <6>; + next-level-cache = <&L2_6>; + L2_6: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu7: PowerPC,e500mc@7 { + device_type = "cpu"; + reg = <7>; + next-level-cache = <&L2_7>; + L2_7: l2-cache { + next-level-cache = <&cpc>; + }; + }; + }; + + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p3060-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p3060-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr>; + reg = <0x12000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p3060-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p3060-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + dcsr-cpu-sb-proxy@44000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu4>; + reg = <0x44000 0x1000>; + }; + dcsr-cpu-sb-proxy@45000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu5>; + reg = <0x45000 0x1000>; + }; + dcsr-cpu-sb-proxy@46000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu6>; + reg = <0x46000 0x1000>; + }; + dcsr-cpu-sb-proxy@47000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu7>; + reg = <0x47000 0x1000>; + }; + }; + + soc: soc@ffe000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x00000000 0xf 0xfe000000 0x1000000>; + reg = <0xf 0xfe000000 0 0x00001000>; + + soc-sram-error { + compatible = "fsl,soc-sram-error"; + interrupts = <16 2 1 29>; + }; + + corenet-law@0 { + compatible = "fsl,corenet-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <32>; + }; + + ddr: memory-controller@8000 { + compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; + + cpc: l3-cache-controller@10000 { + compatible = "fsl,p3060-l3-cache-controller", "cache"; + reg = <0x10000 0x1000 + 0x11000 0x1000>; + interrupts = <16 2 1 27>; + }; + + corenet-cf@18000 { + compatible = "fsl,corenet-cf"; + reg = <0x18000 0x1000>; + interrupts = <16 2 1 31>; + fsl,ccf-num-csdids = <32>; + fsl,ccf-num-snoopids = <32>; + }; + + iommu@20000 { + compatible = "fsl,pamu-v1.0", "fsl,pamu"; + reg = <0x20000 0x5000>; + interrupts = < + 24 2 0 0 + 16 2 1 30>; + }; + + mpic: pic@40000 { + clock-frequency = <0>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <4>; + reg = <0x40000 0x40000>; + compatible = "fsl,mpic", "chrp,open-pic"; + device_type = "open-pic"; + }; + + msi0: msi@41600 { + compatible = "fsl,mpic-msi"; + reg = <0x41600 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 0 0 + 0xe1 0 0 0 + 0xe2 0 0 0 + 0xe3 0 0 0 + 0xe4 0 0 0 + 0xe5 0 0 0 + 0xe6 0 0 0 + 0xe7 0 0 0>; + }; + + msi1: msi@41800 { + compatible = "fsl,mpic-msi"; + reg = <0x41800 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe8 0 0 0 + 0xe9 0 0 0 + 0xea 0 0 0 + 0xeb 0 0 0 + 0xec 0 0 0 + 0xed 0 0 0 + 0xee 0 0 0 + 0xef 0 0 0>; + }; + + msi2: msi@41a00 { + compatible = "fsl,mpic-msi"; + reg = <0x41a00 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xf0 0 0 0 + 0xf1 0 0 0 + 0xf2 0 0 0 + 0xf3 0 0 0 + 0xf4 0 0 0 + 0xf5 0 0 0 + 0xf6 0 0 0 + 0xf7 0 0 0>; + }; + + rmu: rmu@d3000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,srio-rmu"; + reg = <0xd3000 0x500>; + ranges = <0x0 0xd3000 0x500>; + + message-unit@0 { + compatible = "fsl,srio-msg-unit"; + reg = <0x0 0x100>; + interrupts = < + 60 2 0 0 /* msg1_tx_irq */ + 61 2 0 0>;/* msg1_rx_irq */ + }; + message-unit@100 { + compatible = "fsl,srio-msg-unit"; + reg = <0x100 0x100>; + interrupts = < + 62 2 0 0 /* msg2_tx_irq */ + 63 2 0 0>;/* msg2_rx_irq */ + }; + doorbell-unit@400 { + compatible = "fsl,srio-dbell-unit"; + reg = <0x400 0x80>; + interrupts = < + 56 2 0 0 /* bell_outb_irq */ + 57 2 0 0>;/* bell_inb_irq */ + }; + port-write-unit@4e0 { + compatible = "fsl,srio-port-write-unit"; + reg = <0x4e0 0x20>; + interrupts = <16 2 1 11>; + }; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; + + pins: global-utilities@e0e00 { + compatible = "fsl,qoriq-pin-control-1.0"; + reg = <0xe0e00 0x200>; + #sleep-cells = <2>; + }; + + clockgen: global-utilities@e1000 { + compatible = "fsl,p3060-clockgen", "fsl,qoriq-clockgen-1.0"; + reg = <0xe1000 0x1000>; + clock-frequency = <0>; + }; + + rcpm: global-utilities@e2000 { + compatible = "fsl,qoriq-rcpm-1.0"; + reg = <0xe2000 0x1000>; + #sleep-cells = <1>; + }; + + sfp: sfp@e8000 { + compatible = "fsl,p3060-sfp", "fsl,qoriq-sfp-1.0"; + reg = <0xe8000 0x1000>; + }; + + serdes: serdes@ea000 { + compatible = "fsl,p3060-serdes"; + reg = <0xea000 0x1000>; + }; + + dma0: dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p3060-dma", "fsl,eloplus-dma"; + reg = <0x100300 0x4>; + ranges = <0x0 0x100100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <31 2 0 0>; + }; + }; + + dma1: dma@101300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p3060-dma", "fsl,eloplus-dma"; + reg = <0x101300 0x4>; + ranges = <0x0 0x101100 0x200>; + cell-index = <1>; + dma-channel@0 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <32 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <33 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <34 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <35 2 0 0>; + }; + }; + + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,p3060-espi", "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2 0 0>; + fsl,espi-num-chipselects = <4>; + }; + + i2c@118000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x118000 0x100>; + interrupts = <38 2 0 0>; + dfsrr; + }; + + i2c@118100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x118100 0x100>; + interrupts = <38 2 0 0>; + dfsrr; + }; + + i2c@119000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <2>; + compatible = "fsl-i2c"; + reg = <0x119000 0x100>; + interrupts = <39 2 0 0>; + dfsrr; + }; + + i2c@119100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <3>; + compatible = "fsl-i2c"; + reg = <0x119100 0x100>; + interrupts = <39 2 0 0>; + dfsrr; + }; + + serial0: serial@11c500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11c500 0x100>; + clock-frequency = <0>; + interrupts = <36 2 0 0>; + }; + + serial1: serial@11c600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11c600 0x100>; + clock-frequency = <0>; + interrupts = <36 2 0 0>; + }; + + serial2: serial@11d500 { + cell-index = <2>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11d500 0x100>; + clock-frequency = <0>; + interrupts = <37 2 0 0>; + }; + + serial3: serial@11d600 { + cell-index = <3>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11d600 0x100>; + clock-frequency = <0>; + interrupts = <37 2 0 0>; + }; + + gpio0: gpio@130000 { + compatible = "fsl,p3060-gpio", "fsl,qoriq-gpio"; + reg = <0x130000 0x1000>; + interrupts = <55 2 0 0>; + #gpio-cells = <2>; + gpio-controller; + }; + + usb0: usb@210000 { + compatible = "fsl,p3060-usb2-mph", + "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph"; + reg = <0x210000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <44 0x2 0 0>; + }; + + usb1: usb@211000 { + compatible = "fsl,p3060-usb2-dr", + "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr"; + reg = <0x211000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <45 0x2 0 0>; + }; + + crypto: crypto@300000 { + compatible = "fsl,sec-v4.1", "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x300000 0x10000>; + ranges = <0 0x300000 0x10000>; + interrupt-parent = <&mpic>; + interrupts = <92 2 0 0>; + + sec_jr0: jr@1000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x1000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <88 2 0 0>; + }; + + sec_jr1: jr@2000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <89 2 0 0>; + }; + + sec_jr2: jr@3000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x3000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <90 2 0 0>; + }; + + sec_jr3: jr@4000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x4000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <91 2 0 0>; + }; + + rtic@6000 { + compatible = "fsl,sec-v4.1-rtic", "fsl,sec-v4.0-rtic"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x6000 0x100>; + ranges = <0x0 0x6100 0xe00>; + + rtic_a: rtic-a@0 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x00 0x20 0x100 0x80>; + }; + + rtic_b: rtic-b@20 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x20 0x20 0x200 0x80>; + }; + + rtic_c: rtic-c@40 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x40 0x20 0x300 0x80>; + }; + + rtic_d: rtic-d@60 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x60 0x20 0x500 0x80>; + }; + }; + }; + + sec_mon: sec_mon@314000 { + compatible = "fsl,sec-v4.1-mon", "fsl,sec-v4.0-mon"; + reg = <0x314000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <93 2 0 0>; + }; + }; + + rapidio@ffe0c0000 { + compatible = "fsl,srio"; + interrupts = <16 2 1 11>; + #address-cells = <2>; + #size-cells = <2>; + fsl,srio-rmu-handle = <&rmu>; + ranges; + + port1 { + #address-cells = <2>; + #size-cells = <2>; + cell-index = <1>; + }; + + port2 { + #address-cells = <2>; + #size-cells = <2>; + cell-index = <2>; + }; + }; + + localbus@ffe124000 { + compatible = "fsl,p3060-elbc", "fsl,elbc", "simple-bus"; + interrupts = <25 2 0 0>; + #address-cells = <2>; + #size-cells = <1>; + }; + + pci0: pcie@ffe200000 { + compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2"; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + bus-range = <0x0 0xff>; + clock-frequency = <33333333>; + fsl,msi = <&msi0>; + interrupts = <16 2 1 15>; + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + interrupts = <16 2 1 15>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 40 1 0 0 + 0000 0 0 2 &mpic 1 1 0 0 + 0000 0 0 3 &mpic 2 1 0 0 + 0000 0 0 4 &mpic 3 1 0 0 + >; + }; + }; + + pci1: pcie@ffe201000 { + compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2"; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + bus-range = <0 0xff>; + clock-frequency = <33333333>; + fsl,msi = <&msi1>; + interrupts = <16 2 1 14>; + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + interrupts = <16 2 1 14>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 41 1 0 0 + 0000 0 0 2 &mpic 5 1 0 0 + 0000 0 0 3 &mpic 6 1 0 0 + 0000 0 0 4 &mpic 7 1 0 0 + >; + }; + }; +}; diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts index eb11098bb687..c7916dc28014 100644 --- a/arch/powerpc/boot/dts/p4080ds.dts +++ b/arch/powerpc/boot/dts/p4080ds.dts @@ -45,6 +45,10 @@ device_type = "memory"; }; + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + soc: soc@ffe000000 { spi@110000 { flash@0 { @@ -108,7 +112,8 @@ localbus@ffe124000 { reg = <0xf 0xfe124000 0 0x1000>; - ranges = <0 0 0xf 0xe8000000 0x08000000>; + ranges = <0 0 0xf 0xe8000000 0x08000000 + 3 0 0xf 0xffdf0000 0x00008000>; flash@0,0 { compatible = "cfi-flash"; @@ -116,6 +121,11 @@ bank-width = <2>; device-width = <2>; }; + + board-control@3,0 { + compatible = "fsl,p4080ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + }; }; pci0: pcie@ffe200000 { diff --git a/arch/powerpc/boot/dts/p4080si.dtsi b/arch/powerpc/boot/dts/p4080si.dtsi index b71051f506c1..f20c01ab2473 100644 --- a/arch/powerpc/boot/dts/p4080si.dtsi +++ b/arch/powerpc/boot/dts/p4080si.dtsi @@ -42,6 +42,7 @@ aliases { ccsr = &soc; + dcsr = &dcsr; serial0 = &serial0; serial1 = &serial1; @@ -77,7 +78,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu0: PowerPC,4080@0 { + cpu0: PowerPC,e500mc@0 { device_type = "cpu"; reg = <0>; next-level-cache = <&L2_0>; @@ -85,7 +86,7 @@ next-level-cache = <&cpc>; }; }; - cpu1: PowerPC,4080@1 { + cpu1: PowerPC,e500mc@1 { device_type = "cpu"; reg = <1>; next-level-cache = <&L2_1>; @@ -93,7 +94,7 @@ next-level-cache = <&cpc>; }; }; - cpu2: PowerPC,4080@2 { + cpu2: PowerPC,e500mc@2 { device_type = "cpu"; reg = <2>; next-level-cache = <&L2_2>; @@ -101,7 +102,7 @@ next-level-cache = <&cpc>; }; }; - cpu3: PowerPC,4080@3 { + cpu3: PowerPC,e500mc@3 { device_type = "cpu"; reg = <3>; next-level-cache = <&L2_3>; @@ -109,7 +110,7 @@ next-level-cache = <&cpc>; }; }; - cpu4: PowerPC,4080@4 { + cpu4: PowerPC,e500mc@4 { device_type = "cpu"; reg = <4>; next-level-cache = <&L2_4>; @@ -117,7 +118,7 @@ next-level-cache = <&cpc>; }; }; - cpu5: PowerPC,4080@5 { + cpu5: PowerPC,e500mc@5 { device_type = "cpu"; reg = <5>; next-level-cache = <&L2_5>; @@ -125,7 +126,7 @@ next-level-cache = <&cpc>; }; }; - cpu6: PowerPC,4080@6 { + cpu6: PowerPC,e500mc@6 { device_type = "cpu"; reg = <6>; next-level-cache = <&L2_6>; @@ -133,7 +134,7 @@ next-level-cache = <&cpc>; }; }; - cpu7: PowerPC,4080@7 { + cpu7: PowerPC,e500mc@7 { device_type = "cpu"; reg = <7>; next-level-cache = <&L2_7>; @@ -143,6 +144,99 @@ }; }; + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p4080-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p4080-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr1>; + reg = <0x12000 0x1000>; + }; + dcsr-ddr@13000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr2>; + reg = <0x13000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p4080-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p4080-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + dcsr-cpu-sb-proxy@42000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu2>; + reg = <0x42000 0x1000>; + }; + dcsr-cpu-sb-proxy@43000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu3>; + reg = <0x43000 0x1000>; + }; + dcsr-cpu-sb-proxy@44000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu4>; + reg = <0x44000 0x1000>; + }; + dcsr-cpu-sb-proxy@45000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu5>; + reg = <0x45000 0x1000>; + }; + dcsr-cpu-sb-proxy@46000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu6>; + reg = <0x46000 0x1000>; + }; + dcsr-cpu-sb-proxy@47000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu7>; + reg = <0x47000 0x1000>; + }; + }; + soc: soc@ffe000000 { #address-cells = <1>; #size-cells = <1>; @@ -162,13 +256,13 @@ fsl,num-laws = <32>; }; - memory-controller@8000 { + ddr1: memory-controller@8000 { compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller"; reg = <0x8000 0x1000>; interrupts = <16 2 1 23>; }; - memory-controller@9000 { + ddr2: memory-controller@9000 { compatible = "fsl,qoriq-memory-controller-v4.4","fsl,qoriq-memory-controller"; reg = <0x9000 0x1000>; interrupts = <16 2 1 22>; diff --git a/arch/powerpc/boot/dts/p5020ds.dts b/arch/powerpc/boot/dts/p5020ds.dts index 8366e2fd2fba..e6d40999ccd7 100644 --- a/arch/powerpc/boot/dts/p5020ds.dts +++ b/arch/powerpc/boot/dts/p5020ds.dts @@ -45,6 +45,10 @@ device_type = "memory"; }; + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + soc: soc@ffe000000 { spi@110000 { flash@0 { @@ -147,8 +151,8 @@ }; board-control@3,0 { - compatible = "fsl,p5020ds-pixis"; - reg = <3 0 0x20>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; }; }; diff --git a/arch/powerpc/boot/dts/p5020si.dtsi b/arch/powerpc/boot/dts/p5020si.dtsi index 5e6048ec55bb..e7948ad71fa3 100644 --- a/arch/powerpc/boot/dts/p5020si.dtsi +++ b/arch/powerpc/boot/dts/p5020si.dtsi @@ -42,6 +42,7 @@ aliases { ccsr = &soc; + dcsr = &dcsr; serial0 = &serial0; serial1 = &serial1; @@ -98,6 +99,69 @@ }; }; + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p5020-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p5020-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr1>; + reg = <0x12000 0x1000>; + }; + dcsr-ddr@13000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr2>; + reg = <0x13000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p5020-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p5020-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + }; + soc: soc@ffe000000 { #address-cells = <1>; #size-cells = <1>; @@ -117,13 +181,13 @@ fsl,num-laws = <32>; }; - memory-controller@8000 { + ddr1: memory-controller@8000 { compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller"; reg = <0x8000 0x1000>; interrupts = <16 2 1 23>; }; - memory-controller@9000 { + ddr2: memory-controller@9000 { compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller"; reg = <0x9000 0x1000>; interrupts = <16 2 1 22>; diff --git a/arch/powerpc/boot/dts/sbc8560.dts b/arch/powerpc/boot/dts/sbc8560.dts index 9e13ed8a1193..72078eb15616 100644 --- a/arch/powerpc/boot/dts/sbc8560.dts +++ b/arch/powerpc/boot/dts/sbc8560.dts @@ -331,7 +331,7 @@ }; localbus@ff705000 { - compatible = "fsl,mpc8560-localbus"; + compatible = "fsl,mpc8560-localbus", "simple-bus"; #address-cells = <2>; #size-cells = <1>; reg = <0xff705000 0x100>; // BRx, ORx, etc. diff --git a/arch/powerpc/boot/dts/yosemite.dts b/arch/powerpc/boot/dts/yosemite.dts index 64923245f0e5..30bb4753577a 100644 --- a/arch/powerpc/boot/dts/yosemite.dts +++ b/arch/powerpc/boot/dts/yosemite.dts @@ -138,6 +138,42 @@ clock-frequency = <0>; /* Filled in by zImage */ interrupts = <0x5 0x1>; interrupt-parent = <&UIC1>; + + nor_flash@0,0 { + compatible = "amd,s29gl256n", "cfi-flash"; + bank-width = <2>; + reg = <0x00000000 0x00000000 0x04000000>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "kernel"; + reg = <0x00000000 0x001e0000>; + }; + partition@1e0000 { + label = "dtb"; + reg = <0x001e0000 0x00020000>; + }; + partition@200000 { + label = "ramdisk"; + reg = <0x00200000 0x01400000>; + }; + partition@1600000 { + label = "jffs2"; + reg = <0x01600000 0x00400000>; + }; + partition@1a00000 { + label = "user"; + reg = <0x01a00000 0x02540000>; + }; + partition@3f40000 { + label = "env"; + reg = <0x03f40000 0x00040000>; + }; + partition@3f80000 { + label = "u-boot"; + reg = <0x03f80000 0x00080000>; + }; + }; }; UART0: serial@ef600300 { |