diff options
Diffstat (limited to 'arch/powerpc')
| -rw-r--r-- | arch/powerpc/include/asm/reg_fsl_emb.h | 2 | ||||
| -rw-r--r-- | arch/powerpc/kernel/kgdb.c | 2 | ||||
| -rw-r--r-- | arch/powerpc/kernel/tau_6xx.c | 2 | ||||
| -rw-r--r-- | arch/powerpc/kernel/vdso.c | 2 | ||||
| -rw-r--r-- | arch/powerpc/oprofile/op_model_cell.c | 6 | ||||
| -rw-r--r-- | arch/powerpc/platforms/52xx/mpc52xx_pci.c | 2 | ||||
| -rw-r--r-- | arch/powerpc/platforms/powermac/pci.c | 2 | ||||
| -rw-r--r-- | arch/powerpc/sysdev/dart_iommu.c | 2 |
8 files changed, 10 insertions, 10 deletions
diff --git a/arch/powerpc/include/asm/reg_fsl_emb.h b/arch/powerpc/include/asm/reg_fsl_emb.h index 1e180a594589..0de404dfee8b 100644 --- a/arch/powerpc/include/asm/reg_fsl_emb.h +++ b/arch/powerpc/include/asm/reg_fsl_emb.h @@ -39,7 +39,7 @@ #define PMRN_PMLCB2 0x112 /* PM Local Control B2 */ #define PMRN_PMLCB3 0x113 /* PM Local Control B3 */ -#define PMLCB_THRESHMUL_MASK 0x0700 /* Threshhold Multiple Field */ +#define PMLCB_THRESHMUL_MASK 0x0700 /* Threshold Multiple Field */ #define PMLCB_THRESHMUL_SHIFT 8 #define PMLCB_THRESHOLD_MASK 0x003f /* Threshold Field */ diff --git a/arch/powerpc/kernel/kgdb.c b/arch/powerpc/kernel/kgdb.c index 641c74bb8e27..b6bd1eaa1c24 100644 --- a/arch/powerpc/kernel/kgdb.c +++ b/arch/powerpc/kernel/kgdb.c @@ -52,7 +52,7 @@ static struct hard_trap_info { 0x2030, 0x08 /* SIGFPE */ }, /* spe fp data */ { 0x2040, 0x08 /* SIGFPE */ }, /* spe fp data */ { 0x2050, 0x08 /* SIGFPE */ }, /* spe fp round */ - { 0x2060, 0x0e /* SIGILL */ }, /* performace monitor */ + { 0x2060, 0x0e /* SIGILL */ }, /* performance monitor */ { 0x2900, 0x08 /* SIGFPE */ }, /* apu unavailable */ { 0x3100, 0x0e /* SIGALRM */ }, /* fixed interval timer */ { 0x3200, 0x02 /* SIGINT */ }, /* watchdog */ diff --git a/arch/powerpc/kernel/tau_6xx.c b/arch/powerpc/kernel/tau_6xx.c index c3a56d65c5a9..a753b72efbc0 100644 --- a/arch/powerpc/kernel/tau_6xx.c +++ b/arch/powerpc/kernel/tau_6xx.c @@ -59,7 +59,7 @@ void set_thresholds(unsigned long cpu) mtspr(SPRN_THRM1, THRM1_THRES(tau[cpu].low) | THRM1_V | THRM1_TIE | THRM1_TID); /* setup THRM2, - * threshold, valid bit, enable interrupts, interrupt when above threshhold + * threshold, valid bit, enable interrupts, interrupt when above threshold */ mtspr (SPRN_THRM2, THRM1_THRES(tau[cpu].high) | THRM1_V | THRM1_TIE); #else diff --git a/arch/powerpc/kernel/vdso.c b/arch/powerpc/kernel/vdso.c index 137dc22afa42..d84d19224a95 100644 --- a/arch/powerpc/kernel/vdso.c +++ b/arch/powerpc/kernel/vdso.c @@ -721,7 +721,7 @@ static int __init vdso_init(void) #ifdef CONFIG_PPC64 /* - * Fill up the "systemcfg" stuff for backward compatiblity + * Fill up the "systemcfg" stuff for backward compatibility */ strcpy((char *)vdso_data->eye_catcher, "SYSTEMCFG:PPC64"); vdso_data->version.major = SYSTEMCFG_MAJOR; diff --git a/arch/powerpc/oprofile/op_model_cell.c b/arch/powerpc/oprofile/op_model_cell.c index ae06c6236d9c..2c9e52267292 100644 --- a/arch/powerpc/oprofile/op_model_cell.c +++ b/arch/powerpc/oprofile/op_model_cell.c @@ -248,7 +248,7 @@ static int pm_rtas_activate_signals(u32 node, u32 count) * There is no debug setup required for the cycles event. * Note that only events in the same group can be used. * Otherwise, there will be conflicts in correctly routing - * the signals on the debug bus. It is the responsiblity + * the signals on the debug bus. It is the responsibility * of the OProfile user tool to check the events are in * the same group. */ @@ -1594,7 +1594,7 @@ static void cell_handle_interrupt_spu(struct pt_regs *regs, * to a latch. The new values (interrupt setting bits, reset * counter value etc.) are not copied to the actual registers * until the performance monitor is enabled. In order to get - * this to work as desired, the permormance monitor needs to + * this to work as desired, the performance monitor needs to * be disabled while writing to the latches. This is a * HW design issue. */ @@ -1668,7 +1668,7 @@ static void cell_handle_interrupt_ppu(struct pt_regs *regs, * to a latch. The new values (interrupt setting bits, reset * counter value etc.) are not copied to the actual registers * until the performance monitor is enabled. In order to get - * this to work as desired, the permormance monitor needs to + * this to work as desired, the performance monitor needs to * be disabled while writing to the latches. This is a * HW design issue. */ diff --git a/arch/powerpc/platforms/52xx/mpc52xx_pci.c b/arch/powerpc/platforms/52xx/mpc52xx_pci.c index dd43114e9684..da110bd88346 100644 --- a/arch/powerpc/platforms/52xx/mpc52xx_pci.c +++ b/arch/powerpc/platforms/52xx/mpc52xx_pci.c @@ -100,7 +100,7 @@ const struct of_device_id mpc52xx_pci_ids[] __initdata = { }; /* ======================================================================== */ -/* PCI configuration acess */ +/* PCI configuration access */ /* ======================================================================== */ static int diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c index e81403b245b5..ab2027cdf893 100644 --- a/arch/powerpc/platforms/powermac/pci.c +++ b/arch/powerpc/platforms/powermac/pci.c @@ -302,7 +302,7 @@ static void __init setup_chaos(struct pci_controller *hose, * 1 -> Skip the device but act as if the access was successfull * (return 0xff's on reads, eventually, cache config space * accesses in a later version) - * -1 -> Hide the device (unsuccessful acess) + * -1 -> Hide the device (unsuccessful access) */ static int u3_ht_skip_device(struct pci_controller *hose, struct pci_bus *bus, unsigned int devfn) diff --git a/arch/powerpc/sysdev/dart_iommu.c b/arch/powerpc/sysdev/dart_iommu.c index ae3c4db86fe8..bafc3f85360d 100644 --- a/arch/powerpc/sysdev/dart_iommu.c +++ b/arch/powerpc/sysdev/dart_iommu.c @@ -160,7 +160,7 @@ static int dart_build(struct iommu_table *tbl, long index, dp = ((unsigned int*)tbl->it_base) + index; - /* On U3, all memory is contigous, so we can move this + /* On U3, all memory is contiguous, so we can move this * out of the loop. */ l = npages; |